Crafstman CMXEVBCV430L Owner's manual

Category
Vacuum cleaners
Type
Owner's manual
4 U.S. GALLON
*
WET/DRY VAC
ASPIRATEUR DE DÉBRIS SECS/HUMIDES - 4 GALLONS
AMÉRICAINS*
ASPIRADORA PARA LÍQUIDOS/SÓLIDOS DE 4 GALONES
ESTADOUNIDENSES*
Household and Workshop Use
Pour usage domestique et en atelier
Para uso en talleres y doméstico
CMXEVBCV430L
INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCTIONES
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.
1-888-331-4569 WWW.CRAFTSMAN.COM
87558-08
ENGLISH
10
13
3
COMPONENTS
1
Vacuum
2
Hose Inlet
3
Blower Port (not pictured)
4
Caster Feet (4)
5
Casters (4)
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or seriousinjury.
WARNING: Never modify the product or any part of it. Damage or personal injury couldresult.
WARNING: To reduce the risk of injury, read the instructionmanual.
If you have any questions or comments about this or any product, call CRAFTSMAN toll free at: 1-888-331-4569.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
seriousinjury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderateinjury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.
1
5
4
6
8
Tools Included:
Filters Included:
7
9
2
18
6
Lid Latches
7
Plug
8
Grounding Pin
9
Screws (4)
10
Hose Strap
11
Extension Wands (3)
12
Hose
13
Utility Nozzle
14
Cartridge Filter
15
Retainer
16
Foam Sleeve
17
Filter Bag
18
Tool Holder
1
16
14
12
11
15
17
ENGLISH
CMXEVBCV430L
IMPORTANT SAFETY
INSTRUCTIONS
Read all safety rules carefully before attempting
to operate.
DANGER:
Never operate this unit
when flammable materials or vapors are
present.
What can happen How to prevent it
Because electrical devices produce
arcs or sparks, ammable materials
and vapors can cause a re or
explosion.
Never use the vacuum around
ammable materials or vapors.
WARNING:
ALWAYS DISCONNECT
THE PLUG FROM THE WALL OUTLET BEFORE
REMOVING THE TANK COVER.
What can happen How to prevent it
Always unplug power cord
from the wall outlet before
removing the tank cover.
Vacuum could turn on.
WARNING: ALWAYS WEAR EYE
PROTECTION.
What can happen How to prevent it
Always wear eye protection while
operating vacuum.
Rocks or debris can be blown or
ricochet into the eyes or face
which can result in serious injury.
When using an electrical appliance, basic precautions should
always be followed, including the following: READ ALL
INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING: TO REDUCE THE RISK OF
FIRE ELECTRIC SHOCK OR INJURY:
a) Do not leave appliance when plugged in. Unplug from
outlet when not in use and before servicing. Connect
to a properly grounded outlet only. See Grounding
Instructions.
b) Do not expose to rain – store indoors.
c) Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
d) Use only as described in this manual. Use only
Manufacturer’s recommended attachments.
e) Do not use with damaged cord or plug. If appliance
is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return
to service center.
f) Do Not: pull or carry by cord, use cord as a handle,
close a door on cord or pull cord around sharp edges
or corners. Do not run appliance over cord. Keep cord
away from heated surfaces.
g) Do not unplug by pulling on cord. To unplug, grasp
the plug; not the cord.
h) Do not handle plug or appliance with wet hands.
i) Do not put any object into openings. Do not use with
any openings blocked; keep free of dust, lint, hair and
anything that may reduce air flow.
j) Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
k) Do not pick up anything that is burning or smoking,
such as cigarettes, matches or hot ashes.
l) Do not use without dust bag and/or filters in place.
m) Turn off all controls before unplugging.
n) Use extra care when cleaning on stairs.
o) Do not use to pick up flammable or combustible
liquids such as gasoline or use in areas where they
may be present.
p) Do not use the cleaner as a sprayer of flammable
liquids such as oil base paints, lacquers, household
cleaners, etc.
q) Do not vacuum toxic, carcinogenic, combustible or
other hazardous materials such as asbestos, arsenic,
barium, beryllium, lead, pesticides or other health
endangering materials. Specially designed units are
available for these purposes.
r) Do not pick up soot, cement, plaster or drywall dust
without cartridge filter and collection filter bag in
place. These are very fine particles that may pass
through the foam and affect the performance of the
motor or be exhausted back into the air. Additional
collection filter bags are available.
s) Do not leave the cord lying on the floor once you have
finished the cleaning job. It can become a tripping
hazard.
t) Use special care when emptying heavily loaded tanks.
u) To avoid spontaneous combustion, empty tank after
each use.
v) The operation of a utility vac can result in foreign
objects being blown into eyes, which can result in eye
damage. Always wear safety goggles when operating
vacuum.
w) STAY ALERT. Watch what you are doing and use
common sense. Do not use vacuum cleaner when you
are tired, distracted or under the influence of drugs,
alcohol or medication causing diminished control.
x) WARNING: Do NOT use this vacuum cleaner to
vacuum lead paint debris because this may disperse
fine lead particles into the air. This vacuum cleaner is
not intended for use under EPA Regulation 40 CFR Part
745 for lead paint material cleanup.
2
ENGLISH
Volts
Total length of cord in feet
120V
Ampere Rating
More Not More
Than Than
0 - 6
6 - 10
10 - 12
25 50 100
150
AWG
18
18
18
16
16
16
16
14
14
14
12
12
TABLE A
UNPACKING
Pull lid latches
6
in an outward motion and remove tank
cover. Remove any accessories and literature that may have
been packed in the vacuum tank.
ASSEMBLY
Caster System Assembly
You will find four casters
5
, four caster feet
4
and
four screws
9
with this wet/dry vacuum.
WARNING:
DO NOT LEAVE
VACUUM UNATTENDED WHEN IT IS PLUGGED IN
AND/OR OPERATING.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
appliance is equipped with a cord having an equipment-
grounding conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
WARNING:
IMPROPER
CONNECTION OF THE EQUIPMENTGROUNDING
CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN
OR SERVICE PERSON IF YOU ARE IN DOUBT
AS TO WHETHER THE OUTLET IS PROPERLY
GROUNDED. DO NOT MODIFY THE PLUG
PROVIDED WITH THE APPLIANCE  IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET
INSTALLED BY A QUALIFIED ELECTRICIAN.
This appliance is for use on a nominal 120-volt circuit, and has
a grounded plug
7
and grounding pin
8
that looks like the
plug illustrated in Sketch A. A temporary adapter that looks
like the adapter illustrated in Sketch B and C may be used to
connect this plug to a 2-pole receptacle as shown in Sketch B
if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet
(Sketch A) can be installed by a qualified electrician. The green
colored rigid ear, lug or the like extending from the adapter
must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it
must be held in place by a metal screw.
GROUNDING PIN
GROUNDED
OUTLET
GROUNDED OUTLET BOX
Sketch A
Sketch CSketch B
ADAPTER
TAB FOR
GROUNDING SCREW
ADAPTER
METAL
SCREW
GROUNDED OUTLET BOX
IN CANADA, THE USE OF A TEMPORARY ADAPTER IS NOT
PERMITTED BY THE CANADIAN ELECTRICAL CODE. Make sure
that the appliance is connected to an outlet having the same
configuration as the plug. No adapter should be used with this
appliance.
EXTENSION CORDS
When using the appliance at a distance where an extension
cord becomes necessary, a 3-conductor grounding cord of
adequate size must be used for safety, and to prevent loss of
power and overheating. Use TABLE A to determine A.W.G.
wire size required. To determine ampere rating of the vacuum,
refer to nameplate located on motor housing.
Before using appliance, inspect power cord for loose or exposed
wires and damaged insulation. Make any needed repairs or
replacements before using the appliance. Use only three-wire
outdoor extension cords, which have three-prong grounding-
type plugs and three-pole receptacles which accept the
extension cord’s plug. When vacuuming liquids, be sure the
extension cord connection does not come in contact with the
liquid.
NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR
WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW. THIS IS
ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE
APPLIANCE. TO REDUCE THE FREQUENCY OF STATIC SHOCKS
IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO
THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER.
7
8
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
GROUNDING PIN
GROUNDED
OUTLET
GROUNDED OUTLET BOX
Sketch A
Sketch CSketch B
ADAPTER
TAB FOR
GROUNDING SCREW
ADAPTER
METAL
SCREW
GROUNDED OUTLET BOX
3
ENGLISH
Fig.1
Assemble as follows:
1. With cord disconnected from the receptacle and tank
cover removed, turn tank upside-down so bottom is facing
up.
2. Take caster feet
4
and place into slots on tank. Fig. 1.
3. Secure caster feet
4
to tank with screws provided
9
.
Fig. 2.
4. Insert casters
5
into caster feet
4
by placing the caster
stems into the holes provided. Apply pressure and twisting
motion until casters snap into place. Fig. 3.
Fig. 2
5. Return tank to upright position.
GENERAL SET UP
6. Before replacing tank cover, refer to Dry Pick Up or Wet
Pick Up Operation in user manual to ensure you have the
proper filters installed for this cleaning operation.
7. Replace tank cover, and apply pressure with thumb to
each latch until it snaps tightly into place. Make certain all
lid latches are clamped securely.
8. Insert hose
12
into inlet of tank
2
. Do not over-tighten.
9. Attach the extension wands
11
to the accessory end of
the hose
12
. Twist slightly to tighten the connection. Fig.
4.
10. Attach one of the cleaning accessories (depending on
your cleaning requirements) on the extension wands
11
.
Twist slightly to tighten the connection. Fig. 4.
11. Plug the cord
7
into the wall outlet. Your cleaner is
ready for use. I = ON, O = OFF
FILTER INSTALLATION AND CLEAN UP
Dry Pick Up Operation
NOTE: Never use the vacuum for dry pick up without a dry
use filter installed on the lid cage. Using the vacuum without a
filter will cause dust to discharge from blower port and cause
damage to motor.
INSTALLING AND CLEANING THE CARTRIDGE
FILTER
14
,
15
:
WARNING: ALWAYS DISCONNECT
THE PLUG FROM THE WALL OUTLET BEFORE
REMOVING THE TANK COVER.
NOTE: If foam sleeve
16
is installed on lid cage, remove before
installing the cartridge filter
14
.
12. The cartridge filter
14
can be used for dry pick up and
small quantities of wet pick up. Installation is the same
for both. When picking up large quantities of water
we recommend using a foam sleeve
16
instead of the
cartridge filter
14
. When picking up fine dust or powders
a high efficiency filter bag (not standard with all models)
must be used with the cartridge filter.
NOTE: If cartridge filter
14
has been used for wet pick up, it
must be cleaned and dried before using it for dry pick up.
Fig. 3
Fig. 4
4
ENGLISH
13. With the tank cover in an upside down position, slide the
cartridge filter
14
down over the lid cage, pushing until
the filter seals against the cover. Fig. 5.
14. Place filter retainer
15
into the top of the cartridge filter
14
. Fig. 6.
15. Hold the tank cover with one hand, turn the handle on
the filter retainer
15
clockwise to tighten, locking the
filter
14
into place. Fig. 7.
16. To remove the filter
14
for cleaning, again hold the tank
cover and turn the filter retainer
15
counter-clockwise to
loosen and remove. Fig. 8.
17. Slide the cartridge filter
14
off the lid cage. Fig. 9.
18 To clean cartridge filter
14
shake or brush off excess dirt.
Fig. 10.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
5
ENGLISH
19. Or rinse (from the inside of the filter
14
) with water.
Fig. 11. Dry completely (approximately 24 hours).
INSTALLING FILTER BAG
17
:
Use the filter bag
17
in conjunction with the cartridge filter
14
for easy disposal of the debris. The bag is not required for
normal dry pick up. When picking up fine dust or powders a
high efficiency filter bag (not standard with all models)
must be used. NOTE: For dry use only.
WARNING:
MAKE SURE THE CORD
IS DISCONNECTED FROM THE RECEPTACLE,
TANK COVER IS REMOVED AND THE HOSE IS
DISCONNECTED FROM TANK INLET.
20. Grasp carboard collar firmly and slide rubber guard onto
inlet fitting, as firmly as possible. Fig. 12.
21. When securely in place, expand and position bag
17
around inside of tank. Fig. 13.
WARNING:
KEEP FILTERS CLEAN.
EFFICIENCY OF THE VACUUM IS LARGELY
DEPENDENT ON THE FILTER. A CLOGGED FILTER
CAN CAUSE OVERHEATING AND POSSIBLY
DAMAGE THE CLEANER. CHECK THE FILTER
PERIODICALLY AND REPLACE AS REQUIRED.
WARNING:
FOR FINE DUST
POWDERS
When vacuuming fine dust, or powders of any kind
(plaster, drywall dust, cold ashes, concrete dust, etc.)
a high efficiency drywall filter bag must be used.
When vacuuming normal household dust and debris,
standard household disposable filter bags may be
used.
22. Check the filter
17
for tears or small holes. If none are
found, reinstall the filter
17
. To prevent damage to this
vacuum, do not use a filter
17
with a hole or a tear.
WET PICK UP OPERATION
23. Your vacuum can be used for wet pick up. Remove ALL
dirt and debris found in the tank. Remove all dry use only
filters, including the filter bag
17
, from this vacuum.
24. A clean cartridge
14
filter may be used to pick up small
quantities of liquid. To use the cartridge filter
14
; follow
the cleaning and installation instructions under dry pick
up.
25. For vacuuming large quantities of liquid use a foam
sleeve
16
. To use the foam sleeve
16
; follow the
installation instructions in this section.
26. Misting in the exhaust air or dripping of liquid around the
tank cover may occur if the filter
16
becomes saturated
during wet pick up. If this occurs, remove the filter and
allow to dry, or replace with another dry filter.
27. Turn the unit off immediately upon completing a wet
pick up job or when tank is full and ready to be emptied.
When the tank is full, suction will drastically reduce. Refer
to “automatic suction shut off” in this manual. Raise the
hose
12
to drain any excess liquid into the tank. Follow
the “emptying liquid waste” section in this manual.
28. Before storing the vacuum cleaner or using for dry
pick up, clean and dry the interior of the tank and the
underside of the tank cover. Clean and allow the filters to
dry completely.
NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED
PERIODICALLY; ESPECIALLY AFTER PICKING UP WET, STICKY
ACCIDENTS. THIS CAN BE ACCOMPLISHED WITH A WARM
SOLUTION OF SOAP AND WATER.
Fig. 11
6
Fig. 12
Fig. 13
ENGLISH
FOAM SLEEVE
16
INSTALLATION AND CLEANING:
29. With tank cover in an upside down position, slide foam
sleeve
16
down over lid cage pulling until foam sleeve
16
completely covers lid cage. Fig. 14.
WARNING:
TO CLEAN THE FOAM
SLEEVE, DISCONNECT THE PLUG FROM THE
WALL OUTLET. REMOVE THE TANK COVER
AND PLACE THE COVER IN AN UPSIDEDOWN
POSITION. REMOVE FOAM SLEEVE BY SLIDING IT
UP AND OFF THE LID CAGE.
30. Shake excess debris off of the foam sleeve
16
with a
rapid up and down movement.
31. Hold foam sleeve
16
under running water for a minute
or two, rinsing from the inside of the filter. A water wash
is not always required, depending on the condition of the
foam sleeve.
32. Check the filter
16
for tears. If any are found, replace with
a new filter
16
.
BLOWER FEATURE
33. Your vacuum can be used as a powerful blower. To use
the blower feature
3
, clear the hose of any debris or
obstructions. Insert machine hose
12
end into blower
port
3
located on the back of the tank cover. Twist
the hose end slightly to tighten the connection. Fig.
15. Caution should be used when using as a blower
due to the powerful force of air when using certain
attachments.
WARNING: ALWAYS WEAR EYE
PROTECTION TO PREVENT ROCKS OR DEBRIS
FROM BEING BLOWN OR RICOCHETING INTO THE
EYES OR FACE WHICH CAN RESULT IN SERIOUS
INJURY.
EMPTYING LIQUID WASTE FROM THE TANK
34. To empty liquid waste from the tank, turn the vacuum off
and remove the plug
7
from the wall outlet. Remove
the tank cover and deposit the liquid waste in a suitable
drain. After tank is empty, return the tank cover to its
original position.
AUTOMATIC SUCTION SHUT-OFF
35. The vacuum is equipped with an automatic suction
shut-off that operates when picking up liquids. As the
level of the liquid rises in the tank, an internal float rises
until it seats itself against a seal at the intake of the
motor, shutting off suction. When this happens, the
motor will develop a higher than normal pitch noise and
the suction is drastically reduced. If this occurs, turn unit
off immediately. Failure to turn unit off after float rises
and shuts off suction will result in extensive damage to
the motor. To continue use, empty the liquid waste from
the tank as outlined in the previous section.
NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD
LOSE SUCTION. IF THIS OCCURS, TURN UNIT OFF AND PLACE
VAC IN UPRIGHT POSITION. THIS WILL ALLOW THE FLOAT TO
RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE
TO CONTINUE OPERATION.
LUBRICATION
36. No lubrication is necessary as the motor is equipped with
lifetime lubricated bearings.
TOOL STORAGE
37. Set tank cover onto the tank. Position back of tank facing
you.
38. Take tool holder
18
and slide over notches located on
rear of tank. Fig. 16.
HOSE STRAP
10
39. Wrap hose strap Fig. 17 around hose
12
aligning raised
areas on back of strap into a groove on hose Fig. 18.
Fig. 14
7
Fig. 16
Fig. 15
ENGLISH
Fig. 21
8
40. Insert button #1 into button hole #1 Fig. 19 (this may be
difficult at first), continue to wrap hose strap
10
around
hose
12
Fig. 19. Insert button #2 into button hole #2
Fig. 20.
41. Place vacuum tools in tool holder
18
. Fig. 21. The
vacuum should be stored indoors.
Register Online
Thank you for your purchase. Register your product nowfor:
WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
CONFIRMATION OF OWNERSHIP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.
FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
Register online at www.craftsman.com/registration
Three Year Limited Warranty
CRAFTSMAN will repair or replace, without charge, any
defects due to faulty materials or workmanship for three
years from the date of purchase. This warranty does not
cover part failure due to normal wear or tool abuse. For
further detail of warranty coverage and warranty repair
information, visit www.craftsman.com or call
1-888-331-4569 . This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states orprovinces.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of
your CRAFTSMAN Wet Dry Vacuum for any reason, you can
return it within 90 days from the date of purchase with a
receipt for a full refund – no questionsasked.
Fig. 18
Fig. 19
Fig. 20
Fig. 17
Button hole #2
Button hole #1
Raised area
(fits in groove of hose to
prevent it from slipping)
Button hole #2
Button hole #1
Button #2
Button #1
ENGLISH
TROUBLESHOOTING GUIDE
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
For assistance with your product, visit our website at www.craftsman.com for a list of service centers, or call CRAFTSMAN
at 1-888-331-4569.
PROBLEM CAUSE CORRECTION
Loss of suction wet pick up Clogged filter. Clean filter, see steps 30-32 on page 7.
Full tank. Empty tank, see step 34 on page 7.
Loss of suction dry pick up Full tank. Empty tank.
Clogged filter. Clean filter, see steps 16-19 on pages 5 & 6.
Loss of suction or misting Full tank. Drain and clean tank, see step 34 on page 7.
during wet pick up Saturated filter. Clean filter, see step 26 on page 6.
*Tank capacity refers to actual tank volume, and does not reflect capacity available during operation.
9
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-888-331-4569
for a freereplacement.
FRENCH
10
GUIDE DE DÉPANNAGE
ASSUREZ-VOUS DE SUIVRE LES CONSIGNES DE SÉCURITÉ ET DE MISE À LA TERRE
Pour obtenir de l'aide avec votre produit, consultez notre site Web au www.craftsman.com pour obtenir la liste des
centres de service, ou appelez CRAFTSMAN au 1888331-4569.
PROBLÈME CAUSE CORRECTIF
Perte d'aspiration lors d'un ramassage
de débris humides
Filtre bouché Nettoyez le filtre, voir les étapes 30 à 32 aux pages 7.
Cuve pleine. Videz la cuve, voir l'étape 34 à la page 8.
Perte d'aspiration lors d'un ramassage
de débris secs
Cuve pleine. Videz la cuve.
Filtre bouché. Nettoyez le filtre, voir les étapes 16 à 19 aux pages 6.
Perte d'aspiration ou de brumisation
durant le ramassage de débris humides
Cuve pleine. Videz et nettoyez la cuve, voir l'étape 34 à la page 8.
Filtre saturé. Nettoyez le filtre, voir l'étape 26 à la page 7.
* La capacité de la cuve fait référence à son volume réel et non à la capacité disponible durant le fonctionnement.
CRAFTSMAN®
is a registered trademark of Stanley Black & Decker, Inc., used under license.
es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia.
est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.
© 2019 CRAFTSMAN
Product Manufactured by: Shop-Vac Corporation
Producto fabricado por: Shop-Vac Corporation
Produit fabriqué par: Shop-Vac Corporation
LICENSEE NAME: Shop Vac Corporation
LICENSEE ADDRESS: Williamsport, PA
U.S. & Canada Only • É.-U. et Canada seulement
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Crafstman CMXEVBCV430L Owner's manual

Category
Vacuum cleaners
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI