Whirlpool WED9270XL2 Owner's manual

Brand: Whirlpool

Model: WED9270XL2

Category: Electric laundry dryers

Type: Owner's manual

This manual is also suitable for

ELECTRONIC DRYER

For questions about features, operation/performance, parts,

accessories, or service,call: 1-800-253-1301

or visit our website at...

www.whirlpool.com

In Canada, call: 1-800-807-6777

or visit our website at...

www.whirlpool.ca

QUICK START GUIDE/

DRYER USE ............ PG. 4

Para una versibn en espahol, visite:

www.whirlpool.com

Nt_mero de pieza W10294021A

SECHEUSE

ELECTRONIQUE

Pour assistance, installation, ou service, composez le : 1-800-807-6777

ou visitez notre site internet A..

www.whirlpool.ca

GUIDE DE DI_MARRAGE RAPIDE/UTILISATION

DE LA SI_CHEUSE.... PG. 15

LE0F C 8

Page

DRYER SAFETY ........................................................................................... 2

QUICK START GUIDE/DRYER USE .......................................................... 4

Cycles ....................................................................................................... 6

Additional Features ................................................................................... 7

Control Lock ............................................................................................. 7

Changing Cycles and Settings ................................................................ 8

DRYER CARE ............................................................................................... 8

TROUBLESHOOTING ............................................................................... 10

WARRANTY ............................................................................................... 12

ASSISTANCE OR SERVICE .................................................. BACK COVER

Page

SI_CURITI_ DE LA SI_CHEUSE ................................................................. 13

GUIDE DE DI_MARRAGE RAPIDE/

UTILISATION DE LA SI_CHEUSE ............................................................. 16

Programmes ........................................................................................... 18

Caract6ristiques suppl6mentaires .......................................................... 19

Verrouillage/d6verrouillage des commandes ......................................... 20

Modification des programmes et r6glages ............................................ 20

ENTRETIEN DE LA SECHEUSE ............................................................... 21

DEPANNAGE ............................................................................................. 23

GARANTIE .................................................................................................. 25

ASSISTANCE OU SERVICE ............................... COUVERTURE ARRIERE

W10293937A

W10294021A - SP

CASUAl NORMAL ECONORMAL

........,,,:3 L

......:1 E

ENHANCED REFRESH

TOUCHU_

WARNING: To reduce the risk of fire electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS

before operating this appliance.

This Use and Care Guide covers several different models. Your dryer may not have all the cycles and features described.

r; r i r i r r r r r r r ...............................................................r;r; r r; r; r; r r .............................r r; r r

iiiiiiiiiii_iii

NOTE: Not all cycles are available on all models.

Select the drying cycle that matches the type of load you

are drying. See the Automatic Cycle Settings or Timed Cycle

Settings chart.

CASUALyO"MAkECO"ORMAL

DELICATE___HEAVY DUTY

ENHANCED REFRESH

TOUCH UP

Cycle Control knob

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you are

drying. See the following Automatic Cycle Settings chart. Each

cycle dries certain fabrics at the recommended temperature.

A sensor detects the moisture in the load and automatically

adjusts the drying time for optimal drying. Press the DRYNESS

button to adjust the default dryness level.

Automatic Cycle Settings

Automatic Cycles

Load Type

Temperature

Est.

Cycle

Time

(Minutes)

HEAVY DUTY

Heavyweight items, towels, jeans

High 40

ECO NORMAL

Designed for average size loads

of medium weight where

improved energy is desired

Medium 35

NORMAL

Jackets, pillows, corduroys, work

clothes, sheets

Medium 35

CASUAL Low 35

Permanent press, synthetics

DELICATE

Lingerie, blouses, washable

woolens

Extra Low 30

DAMP DRY

Clothes to come out suitable

for ironing

Low 20

If loads do not seem as dry as you would like, select More Time

next time you dry a similar load.

Timed Cycles

Use Timed Cycles to select a specific amount of drying time

and a drying temperature. When a Timed Cycle is selected,

the Estimated Time Remaining display shows the actual time

remaining inyour cycle.

Press the TEMP button to change the drying temperature from

the default setting.

Press the MORE TIME or LESS TIME button to increase or

decrease the drying time. Tap MORE TIME or LESS TIME

and the time will change by 1-minute intervals. Press and

hold MORE TIME or LESS TIME and the time will change by

5-minute intervals.

Timed Cycle Setting

Timed Cycles Default Default Cycle

Load Type Temperature Time*

(Minutes)

TIMED DRY High 80

Heavyweight items,

bulky items, bedspreads,

work clothes

*Reset time to complete drying, if needed.

Steam Cycle

In these cycles, a small amount of water is sprayed into the dryer

drum after several minutes of tumbling with heat. The STEAM

Status Light will come on while the water is sprayed into the drum.

The dryer will continue to tumble at Medium heat for the duration

of the cycle. The Steam Cycles include Enhanced Touch Up and

Quick Refresh. The heat setting and cycle time are not adjustable

for the Quick Refresh Cycle, but can be adjusted for the Enhanced

Touch Up Cycle.

NOTE: Results may vary depending on fabric. 100% cotton

garments with wrinkle-free finish may yield better results than

those without.

Use of a fabric softener sheet is not recommended with steam

cycles as it may cause temporary staining on the clothes.

Steam Preset Cycle Settings

Timed Cycles Default Est. Time*

Load Type Temperature* (Minutes)

ENHANCED TOUCH UP Medium 20

Helps to smooth out

wrinkles in loads left in the

dryer for an extended

period.

QUICK REFRESH

Helps to smooth out

wrinkles and reduce odors

from loads consisting of

one to four dry items.

Medium 15

*The Enhanced Touch Up Cycle has a minimum dry time of

15 minutes and a maximum dry time of 40 minutes. Only the

Medium and High temperature settings can be used for the

Enhanced Touch Up Cycle.

Air Dry

Use the Air Dry temperature setting with Timed Cycles for items

that require drying without heat such as rubber, plastic, and

heat-sensitive fabrics. This chart shows examples of items that

can be dried using Air Dry.

Type of Load Est.

Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30

Plastic - shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

When using Air Dry:

• Check that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the

Air Dry setting.

More (_

Time

Less @

Time

Signal

hold 3 sec to

IocWunlock

control

Temp Dryness Wrinkle

Shield (90)

Sensing/Estimated Time Remaining

• In an Automatic Cycle, the Sensing light illuminates until a wet

item is detected.

• In the Timed Cycle, the Sensing light illuminates at the beginning

of a cycle and turns off 5 minutes into the cycle.

NOTE: Moisture sensing strips inthe dryer measure the amount of

moisture in the clothes. The estimated time display may adjust to

show a more accurate drying time.

Wet

The Wet light illuminates at the beginning of an Automatic Cycle if a

wet item is detected.

• In an Automatic Cycle, if a wet item is not detected after

approximately 5 minutes, the dryer goes directly into Cool Down

and the Cool Down and the WRINKLE SHIELD TM setting

indicators illuminate, if selected.

• In a Timed Cycle, wet items are not detected. The dryer will

continue to run for the length of time selected, and the Wet light

will illuminate. The damp light will not illuminate.

In the Enhanced Touch Up or the Quick Refresh Steam

Cycles, the Wet light comes on after the water has been

sprayed into the drum, 4-5 minutes into the cycle. The Wet

light illuminates until the dryer goes into Cool Down with

1 minute of time remaining.

Damp Dry Signal

On some models, the Damp Dry Signal may be selected to

alert you that your clothes are approximately 80% dry. This is

useful when you want to remove lightweight items in a mixed

load to avoid overdrying or remove partially dry items that may

need ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens

in a mixed load. When the signal goes off, open the door to stop

the dryer, rearrange the load inside the dryer, close the door and

restart the dryer to finish the drying cycle. Rearranging the load

will aid in the drying process.

NOTE: The Damp Dry Signal is available only with the Automatic

Cycles.

Cool Down

The Cool Down light illuminates during the cool down part of the

cycle. Laundry cools for ease in handling.

Done

The Done light illuminates when the drying cycle isfinished. This

indicator stays on during the WRINKLE SHIELD TM (90) setting.

WRINKLE SHIELD TM (90) Feature

When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The WRINKLE SHIELD TM

(90) feature periodically tumbles, rearranges, and fluffs the load to

help keep wrinkles from forming.

• Get up to 90 minutes of heat-free, periodic tumbling at the

end of a cycle. Press the WRINKLE SHIELD TM (90) button to

turn ON or OFF at any time before the cycle has ended.

• The WRINKLE SHIELD TM (90) feature is preset to "OFF." If

selected for other cycles, the WRINKLE SHIELD TM (90)feature

setting will remain "ON" the next time that cycle is selected.

Signal

The Signal produces an audible sound when the drying cycle is

finished. Press the SIGNAL button to turn On or Off at any time

before the cycle has ended.

NOTE: When the WRINKLE SHIELD TM (90) feature is selected

and the Signal is on, an audible sound will be emitted every

20 minutes until the clothes are removed, or the WRINKLE

SHIELD TM (90) feature is finished.

Indicator Lights

Other indicator lights show Cycle, Modifiers, Options, and Signal

settings selected. The display shows the estimated or actual time

remaining.

This feature allows you to lock your settings to avoid unintended

use of the dryer. You can also use the Control Lock feature to

avoid unintended cycle or option changes during dryer operation.

To enable the Control Lock feature when

dryer is running:

Press and hold the SIGNAL button for 3 seconds. The control is

locked when a single beep is heard and the Control Lock status

light is on.

To enable the Control Lock feature when dryer is OFF:

When the dryer is off, it is not necessary to press the POWER

button before activating the Control Lock feature.

To unlock:

Press and hold the SIGNAL button for 3 seconds to turn this

feature off.

NOTE: When the dryer is running and Control Lock is on, the

dryer can be stopped by pressing the START/PAUSE button,

but cannot be restarted until the control is unlocked.

On Automatic Cycles, you can change the Cycle or Dryness Level

at any time before pressing START/PAUSE.

On Timed Cycles, you can change the Cycles, adjust the time,

or change the temperature setting at any time before pressing

START/PAUSE.

• Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing cycles after pressing START/PAUSE

1. Press POWER. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START/PAUSE. The dryer starts at the

beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting

the cycle, the dryer automatically shuts off.

Changing settings on Timed Cycles during the cycle

On Timed Cycles, at any time, you may:

• Adjust the time by pressing the More or Less Time buttons.

• Change the temperature setting by pressing the Temp button.

DRYERCARE

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

Explosion Hazard

Keep flararaable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 rata) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Every load cleaning:

The lint screen is located in the door opening of the dryer.

A screen blocked by lint can increase drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with your

fingers. Do not rinse or wash screen to remove lint. Wet lint is

hard to remove.

2. Push the lint screen firmly back into place.

IM PORTANT:

• Do not run the dryer if the lint screen is loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

"Venting Requirements."

As needed cleaning:

Laundry detergent and fabric softener residue can build up

on the lint screen. This buildup can cause longer drying times

for your clothes, or cause the dryer to stop before your load is

completely dry.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

Rinse screen with hot water.

Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum:

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth.

Apply a liquid, nonflammable household cleaner to the stained

area and rub with a soft cloth until all excess dye and stains

are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry unstable dye items inside out to

avoid transfer of dye.

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

, _e ............. _£} .......

Install and store your dryer where it will not freeze. Because some

water may stay in the hoses, freezing can damage your dryer. If

storing or moving your dryer during freezing weather, winterize it.

Non-Use or Storage Care

Operate your dryer only when you are at home. Ifyou will be on

vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See "Cleaning the Lint Screen."

3. Turn off the water supply to the dryer. This helps to avoid

unintended flooding (due to a water pressure surge) while you

are away.

Moving care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Steam models only: Shut off water faucet.

3. Steam models only: Disconnect the water inlet hose from

faucet, then drain the hose. Transport hose separately.

4. Make sure leveling legs are secure in dryer base.

5. Use masking tape to secure dryer door.

For direct-wired dryers:

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Water Inlet Hoses

Replace inlet hoses and hose screen after 5 years of use to

reduce the risk of hose failure. Periodically inspect and replace

inlet hoses if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, record the date of replacement.

To winterize dryer

1. Unplug dryer or disconnect power.

2. Shut off water faucet.

3. Disconnect water inlet hose from faucet and drain.

To use dryer again

1. Flush water pipes. Reconnect water inlet hose to faucet. Turn

on water faucet.

2. Plug in dryer or reconnect power.

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light:

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with

the screw.

4. Plug in dryer or reconnect power.

1. Disconnect power.

2. Disconnect wiring.

3. Steam models only: Shut off water faucet.

4. Steam models only: Disconnect the water inlet hose from

faucet, then drain the hose. Transport hose separately.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

Reinstalling the dryer

Follow the "Installation Instructions" to locate, level, and connect

the dryer.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call...

For additional recommendations, refer to your Installation Instructions.

Dryer will not run

Is the dryerdoor firmly closed?

Was the Start/Pause button firmly pressed?

Large loads may require pressing and holding the Start/Pause

button for 2-5 seconds.

Has a household fuse blown, or has a circuit breaker

tripped?

There may be 2 household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuse or reset the

circuit breaker. If the problem continues, call an electrician.

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

Was a regular fuse used?

Use a time-delay fuse.

Unusualsounds

Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

Is a coin, button, or paper clip caught between the drum

and front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

Are the four legs installed, and is the dryer level front to

back and side to side?

The dryer may vibrate if not properly installed. See the

Installation Instructions.

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

No heat

Has a household fuse blown, or has a circuit breaker

tripped?

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the

fuse or reset the circuit breaker. If the problem continues, call

an electrician.

Dryer displaying code message

"PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press and Hold to START to restart the dryer.

"F# E#" (F1 El, F3 El, etc.) variable service codes:

If a code beginning with an "F" appears in the display,

alternating between F# and E#, the dryer control has detected

a problem that requires service. Call for service.

Clothes are not drying satisfactorily, drying times are too

long, or load is too hot

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

Has the Air Dry temperature setting been selected?

Select the right temperature for the types of garments being

dried. See "Air Dry."

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Is the exhaust vent or outside exhaust hood clogged with

lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not

feel air movement, clean exhaust system of lint or replace

exhaust vent with heavy metal or flexible metal vent. See the

Installation Instructions.

• Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

• Are drying times too long or are clothes too dry?

Automatic cycle default settings may have been changed. See

Changing the Automatic Cycle Default Settings.

• Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See the

Installation Instructions. See also Changing the Automatic

Cycle Default Settings, if you are unable to shorten the vent

length.

• Is the exhaust vent diameter the correct size?

Use 4" (102 mm) diameter vent material.

• Is the dryer located in a room with temperature below 45°F

(7°C)?

Proper operation of dryer cycles requires temperatures above

45°F (7°C).

Is the dryer located in a closet?

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25 mm) of airspace, and, for most installations, the rear

of the dryer requires 5" (127 mm). See the Installation

Instructions.

Cycle time too short

• Is the automatic cycle ending early?

The load may not be contacting the sensor strips. Level the

dryer.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness level will change the

amount of drying time in a cycle. If loads are consistently

ending too early, see also Changing the Automatic Dry Default

Settings.

Lint on load

• Is the lint screen clogged?

Clean lint screen. Check for air movement.

Stains on load or drum

Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can

stain your garments.

Drum stains are caused by dyes in clothing (usually blue

jeans). These will not transfer to other clothing.

Loads are wrinkled

Was the load removed from dryer at the end of the cycle?

Select Enhanced Touch Up Cycle to tumble the load with

water and heat. This cycle is best for smoothing out wrinkles

and reducing odors from loads consisting of wrinkle-free

cotton, cotton polyester blends, common knits and synthetic

garments.

NOTE: Refer to garment care label instructions. Dry clean only

garments are not recommended.

Loads are still wrinkled following Steam Cycle?

Make sure water is connected to the dryer. Check that water

inlet hose is connected to both the faucet and dryer's water

inlet valve. Check that the water supply is turned on.

Was the dryer overloaded?

Dry smaller loads that can tumble freely.

Odors

Have you recently been painting, staining, or varnishing in

the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone

from the area, rewash and dry the clothing.

Is water connected to the dryer?

Check that water inlet hose is connected to both the faucet

and dryer's water inlet valve. Check that the water supply is

turned on.

To remove odors left in garments after wearing, select Quick

Refresh for small loads of 1-4 garments. This cycle is best for

reducing wrinkles and odors from loads consisting of wrinkle-

free cotton, cotton polyester blends, common knits, and

synthetics.

IMPORTANT: Your dryness level settings can be adjusted to

adapt to different installations, environmental conditions or

personal preference. This change is retained and will affect all of

your Automatic cycles, not just the current cycle/load.

If all your loads on all Automatic cycles are consistently not as dry

as you would like, you may change the default settings to increase

the default dryness level.

Your default drying settings can be adjusted to adapt to different

installations, environmental conditions or personal preference.

There are 3 drying settings, which are displayed using the time

display:

1. Factory preset dryness level.

2. Slightly drier clothes, 15% more drying time.

3. Much drier clothes, 30% more drying time.

To change the default drying settings:

NOTE: The default settings cannot be changed while the dryer is

running or paused. The dryer must be in standby mode to adjust

the default settings.

1. Press and hold the TEMP button for at least 6 seconds. The

dryer will beep, the letters "CF" will flash briefly in the display,

then the current drying mode will be displayed.

2. To select a new drying setting, press the TEMP button again

until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting

will be lit solid, but the other settings will flash.

3. Press the START/PAUSE button to save the drying setting and

exit to standby mode.

NOTE: To exit without saving, press the POWER button.

4. The drying setting you selected will become your new preset

drying setting for all Automatic cycles.

WHIRLPOOLCORPORATIONLAUNDRYWARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts

and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be

provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies

only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the

problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling

Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/08

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

P P P

SECURITEDELASECHEUSE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediatel_

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

AVERTISSEMENT " "Risque d'incendie"

L'installation de la s_cheuse & linge dolt _tre effectu_e par un installateur qualifi_.

installer la s_cheuse conform_rnent aux instructions du fabricant et au× codes Iocau×.

Ne pas installer de s6cheuse & linge avec des mat6riau× d'6vacuation en plastique

souple. Siun conduit m_tallique souple {de type papier d'alurniniurn) est installS,

celui-ci doit _tre d'un type sp6cifique identifi6 par le fabricant de I'appareil et

convenir & une utilisation avec les s_cheuses _ linge. Les rnat_riau× d'_vacuation

souples sort connus pour s'affaisser, Ctre facilernent 6cras_s et bloquer la charpie.

Ces situations obstrueront le d_bit d'air de la s_cheuse a linge et augrnenteront le

risque d'incendie.

Pour r_duire le risque de blessure grave ou de d_c_s, suivre toutes

les instructions d'installation.

Conserver ces instructions,

AVERTISSEMENT • Pour votre s_curit_, les renseignements dans ce manuel doivent

_tre observes pour reduire au minimum les risques d'incendie ou d'explosion ou pour

6viter des dommages au produit, des blessures ou un d_c_s.

- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables _ proximit6 de cet appareil ou de tout autre appareil electrom6nager.

- QUE FAiRE DANS LE CAS D'UNE ODEUR DE GAZ :

® Ne pas tenter d'allumer un appareil.

® Ne pas toucher _ un commutateur _lectrique; ne pas utiliser le t_l_phone se trouvant

sur les lieux.

= l_vacuer tous les gens de la piece, de I'_difice ou du quarrier.

= Appeler imm6diatement le fournisseur de gaz du t_lephone d'un voisin. Suivre ses

instructions.

= A d_faut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectues par un installateur qualifie, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le fournisseur de gaz local.

En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".

IMPORTANTES iNSTRUCTiONS DE SECURITY:

AMERTISSEM ENT • Pour r6duire le risque d'incendie, de choc 61ectrique ou de blessure Iors de I'utilisation de

la s6cheuse, il convient d'observer certaines pr6cautions 616mentaires dont les suivantes :

[] Lire toutes les instructions avant d'utiliser la s6cheuse.

[] Ne pas placer des articles exposes aux huiles de cuisson

dans votre s6cheuse. Les articles contamin6s par des

huiles de cuisson peuvent contribuer a une r6action

chimique qui pourrait causer a la charge de s'enflammer.

[] Ne pas faire s6cher dans la machine des articles qui ont

d6ja 6t6 nettoy6s, lav6s, imbibes, ou tach6s d'essence,

de solvants pour nettoyage a sec, d'autres substances

inflammables, ou de substances explosives puisqu'elles

d6gagent des vapeurs qui peuvent provoquer un

incendie ou une explosion.

[] Ne pas permettre a des enfants de jouer sur ou

I'int6rieur de la secheuse. Une surveillance 6troite est

n6cessaire Iorsque la s6cheuse est utilis6e pres d'eux.

[] Avant d'enlever la s6cheuse du service ou la jeter, enlever

la porte du compartiment de s6chage.

[] Ne pas mettre la main dans la s6cheuse si le tambour est

en mouvement.

[] Ne pas installer ni entreposer la s6cheuse oQ elle sera

expos6e aux intemp6ries.

[] Ne pas jouer avec les commandes.

[] Ne pas r6parer ni remplacer une piece de la s6cheuse ou

essayer d'en faire I'entretien a moins d'une recommandation

sp6cifique dans le guide d'utlilisation et d'entretien, ou

publi6e dans les instructions de r6paration par I'utilisateur

que vous comprenez et pouvez ex6cuter avec comp6tence.

[] Ne pas utiliser un produit assouplissant de tissu ou des

produits pour 61iminer la statique a moins qu'ils ne soient

recommand6s par le fabricant du produit assouplissant de

tissu ou du produit.

[] Ne pas utiliser la chaleur pour faire secher des articles

fabriqu6s avec du caoutchouc mousse ou des mat6riaux

semblables.

[] Nettoyer le filtre a charpie avant et apres chaque charge.

[] Ne pas laisser la charpie, la poussiere, ou la salet6

s'accumuler autour du systeme d'6vacuation ou autour de

I'appareil.

[] Un nettoyage p6riodique de I'int6rieur de la s6cheuse et du

conduit d'6vacuation doit _tre effectu6 par une personne

qualifi6e.

[] Voir les instructions d'installation pour les exigences de

liaison de I'appareil a la terre.

CONSERVEZ CES INSTRUCTIONS

IMPORTANT : L'installation du gaz dolt se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au National Fuel Gas

Code, ANSI Z223.1/NFPA 54.

La s6cheuse dolt _tre 61ectriquement reli6e &la terre conform6ment aux codes Iocaux, ou en I'absence de codes Iocaux, au Code

canadien de 1'61ectricit6, ANSI/NFPA 70.

Avertissements de la proposition 65 de I'Fttat de Californie "

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'Fttat de Californie pour _tre a I'origine de cancers.

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'Fttat de Californie pour _tre a I'origine de malformations

et autres d6ficiences de naissance.

GUIDEDEDEMARRAGERAPIDE/

UTILISATIONDELASECHEUSE

Risque d'e×plosion

Garder les mati_res et les vapeurs inflammables, telle

que I'essence, loin de la s_cheuse.

Ne pas faire s_cher un article qui a d_j_ _t_ touch_ par

un produit inflammable (m_me apr_s un lavage).

Le non-respect de ces instructions peut causer

un d_c_s, une e×plosion ou un incendie.

Risque d'incendie

Aucune laveuse ne peut compl_tement enlever I'huile.

Ne pas faire s_cher des articles qui ont _t_ salis par

tout genre d'huile (y compris les huiles de cuisson).

Les articles contenant mousse, caoutchouc ou

plastique doivent _tre s6ch_s sur une corde _ linge

ou par le programme de s_chage _ I'air.

Le non-respect de ces instructions peut causer

un d_c_s ou un incendie.

Pour un resum6 sur I'utilisation de la secheuse apres installation, voir le GUIDE DE D#MARRAGE RAPIDE a la page suivante.

iiiiiiiiii!i!i!

REMARQUE : Tousles programmes ne sont pas disponibles sur

tous les modeles.

Selectionner le programme de sechage qui correspond au type

de charge & secher. Voir le tableau Reglages de programmes

automatiques ou Reglages de programmes minutes.

CASUAL NORMAL ECONORMAL

DELICATE__"_/HEAVY DUTY

ENHANCED REFRESH

TOUCH UP

Bouton de commande des programmes

Programmes automatiques

Les programmes automatiques permettent d'assortir le

programme & la charge &secher. Voir le tableau Reglages de

programmes automatiques suivant. Chaque programme seche

certains tissus & la temperature recommandee. Un capteur

detecte I'humidite de la charge et adapte automatiquement la

duree de sechage pour un sechage optimal. Appuyer sur le

bouton DRYNESS (niveau de sechage) pour ajuster le niveau

de sechage par defaut.

R6glages de programmes automatiques

Programmes Automatiques Temperature

Type de charge

Dur_e

estim_e

du pro-

gramme

(en

minutes)

HEAVY DUTY (service intense) #levee 40

Articles Iourds, serviettes, jeans

ECO NORMAL (normal _co) Moyenne 35

Con£;u pour les charges de taille

ordinaire composees d'articles

de poids moyen et pour

lesquelles on souhaite une

meilleure utilisation d'energie

NORMAL

Vestes, oreillers, tissus velours,

vetements de travail, draps

Moyenne 35

CASUAL (tout-aller)

Pressage permanent, tissus

synthetiques

Basse 35

DELICATE (articles d_licats)

Lingerie, chemisiers, lainages

lavables

Tres basse 30

Programmes Automatiques Temperature Dur_e

Type de charge estim_e

du pro-

gramme

(en

minutes)

DAMP DRY (s_chage humide) Basse 20

Les vetements ressortent prets

pour le repassage

S'il semble que les charges ne sont pas aussi seches que

desirees, selectionner More Time (plus de temps) la prochaine fois

que I'on seche une charge semblable.

Programmes minutes

Utiliser un programme minute pour selectionner une duree et une

temperature de sechage specifiques. Lorsqu'un programme

minute est selectionne, I'afficheur de la duree residuelle estimee

indique la duree residuelle reelle pour le programme en cours.

Appuyer sur le bouton TEMP (temperature) pour modifier la

temperature de sechage prereglee par defaut.

Appuyer sur le bouton MORE TIME (plus de temps) ou LESS

TIME (moins de temps) pour augmenter ou diminuer la duree du

sechage. Appuyer legerement sur MORE TIME (plus de temps)

ou LESS TIME (moins de temps) et la duree changera par

tranches de 1 minute. Appuyer sans rel&cher sur MORE TIME ou

LESS TIME; la duree changera par tranches de 5 minutes.

R6glages de programmes minutes

Programmes minutes Temperature

Type de charge par d_faut

Dur_e

estim_e du

programme*

(en minutes)

TIMED DRY

(s_chage minute)

Articles Iourds, articles

volumineux, couvre-lits,

vetements de travail

Elevee 80

*Regler de nouveau la duree pour completer le sechage, si

necessaire.

Programmes vapeur

Avec ces programmes, une petite quantite d'eau est pulverisee

dans le tambour de la secheuse apres plusieurs minutes de

culbutage avec chaleur. Le temoin lumineux STEAM (vapeur)

s'allume Iorsque I'eau est pulverisee dans le tambour. La

secheuse continuera & effectuer le culbutage &une chaleur elevee

pendant la duree du programme. Les programmes vapeur

comprennent les fonctions Quick Refresh (rafrafchissement

rapide) et Enhanced Touch Up (retouche amelioree). Le reglage de

chaleur et la duree de programme ne sont pas reglables pour le

programme Quick Refresh (rafrafchissement rapide), mais

peuvent etre regles pour le programme Enhanced Touch Up

(retouche amelioree).

REMARQUE : Les resultats peuvent varier selon le tissu. II est

possible que les vetements 100 % en coton avec fini

antifroissement donnent de meilleurs resultats que ceux qui ne

possedent pas ce fini.

L'emploi d'une feuille d'assouplissant de tissu n'est pas

recommande avec les programmes vapeur car ceci pourrait

temporairement tacher les vetements.

Pr_r_glages de programme vapeur

Programmes minutes

Type de charge

Temperature Dur_e

par d_faut* estim_e*

(en minutes)

ENHANCED TOUCH UP

(retouche am_lior_e)

Aide a aplanir les faux-plis

pour les charges restees dans

la secheuse pendant

Iongtemps.

Moyenne 20

QUICK REFRESH

(rafraichissement rapide)

Aide a aplanir les faux-plis et

reduire les odeurs des

charges consistant d'un

quatre articles secs.

Moyenne 15

*Le programme Enhanced Touch Up (retouche amelioree)

comporte une duree de sechage minimale de 15 minutes et

maximale de 40 minutes. Pour le programme Enhanced Touch Up

(retouche amelioree), seuls les reglages de temperature moyenne

et elevee peuvent etre utilises.

Air Dry (s_chage _ I'air)

Utiliser le reglage de temperature Air Dry (sechage a I'air) avec les

programmes minutes pour les articles qui doivent etre seches

sans chaleur, tels que le caoutchouc, le plastique et les tissus

sensibles a la chaleur. Ce tableau donne des exemples d'articles

pouvant etre seches au moyen du reglage Air Dry.

Type de charge Dur_e

estim_e*

(en

minutes)

Caoutchouc mousse - oreillers, soutiens-gorges 20 - 30

rembourres, jouets rembourres

Plastique - rideaux de douche, nappes 20 - 30

Tapis a endos caoutchoute 40 - 50

Plastique olefinique, polypropylene, nylon diaphane 10 - 20

*Regler de nouveau la duree pour completer le sechage, si

necessaire.

Lors de I'utilisation du s_chage _ I'air

• Verifier que les revetements sont bien cousus.

• Secouer et faire bouffer les oreillers a la main periodiquement

pendant le programme.

• Faire secher I'article completement. Les oreillers en

caoutchouc mousse mettent du temps a secher.

REMARQUE : Les programmes automatiques ne sont pas

disponibles avec le reglage Air Dry (sechage a I'air).

More (_

Time

Less

Time k._.,J

Signal

hold 3 sec to

!ocWunlock

control

Temp Dryness Wrinkle

Shield (90)

Sensing/Estimated Time Remaining (d_tection/dur_e

restante estim_e)

• Au cours d'un programme automatique, le temoin Sensing est

allume jusqu'a ce qu'un article mouille soit detecte.

• Au cours d'un programme minute, le temoin Sensing s'allume

au debut du programme et s'eteint au bout de 5 minutes.

REMARQUE : Des bandes detectrices d'humidite situees dans la

machine mesurent la quantite d'humidite presente dans les

vetements. L'afficheur de la duree restante estimee pourra

s'ajuster pour afficher une duree de sechage plus precise.

Wet (mouill_)

Le temoin Wet s'allume au debut d'un programme automatique si

un article mouille est detecte.

• Au cours d'un programme automatique, si un article mouille

n'est pas detecte apres environ 5 minutes, lasecheuse passe

directement a la periode de refroidissement et les temoins Cool

Down et WRINKLE SHIELD TM s'allument, si la fonction est

selectionnee.

Au cours d'un programme minute, les articles mouilles ne sont

pas detectes. La secheuse continuera afonctionner pour la

duree de temps selectionnee et le temoin Wet s'allumera. Le

temoin lumineux Damp (humide) ne s'allumera pas.

Dans les programmes a la vapeur Enhanced Touch Up

(retouche amelioree) et Quick Refresh (rafrafchissement

rapide), le temoin Wet s'allume apres I'aspersion de I'eau dans

le tambour, ce qui represente 4 a 5 minutes pendant le

programme. Le temoin Wet reste allume jusqu'a ce que la

secheuse passe au refroidissement, 1 minute avant la fin du

programme.

Damp Dry Signal (signal de s_chage humide)

Sur certains modeles, on peut selectionner le signal de sechage

humide pour etre averti Iorsque les vetements sont secs a environ

80 %. Cette option est utile Iorsqu'on desire retirer des articles

legers d'une charge mixte pour eviter un sechage excessif ou

retirer des articles partiellement secs necessitant un eventuel

repassage.

Le SIGNAL DE SI_CHAGE HUMIDE est utile Iorsqu'on seche des

draps/du linge de maison dans une charge mixte. Lorsque le

signal s'eteint, ouvrir la porte pour arreter la secheuse, rearranger

la charge a I'interieur de la secheuse, fermer la porte et remettre la

secheuse en marche pour terminer le programme. Rearranger la

charge aide les articles a mieux secher.

REMARQUE : Le signal de sechage humide est disponible

uniquement avec les programmes automatiques.

Cool Down (refroidissement)

Le temoin Cool Down s'allume pendant la periode de

refroidissement du programme. Le linge refroidit pour faciliter sa

manipulation.

Done (programme termin_)

Le temoin Done s'allume Iorsque le programme de sechage est

termin& Ce temoin reste allume durant le reglage WRINKLE

SHIELDTM (90).

Caract_ristique WRINKLE SHIELD TM (90)

(anti-froissement)

Lorsqu'on ne peut pas enlever une charge de lasecheuse des

qu'elle s'arrete, des faux plis peuvent se former. La caracteristique

WRINKLE SHIELD TM (90) effectue un culbutage de la charge, la

rearrange et I'aere & intervalles reguliers pour aider &eviter la

formation de faux plis.

• Obtenez jusqu'& 90 minutes de culbutage periodique sans

chaleur a la fin d'un programme. Appuyer sur !e bouton

WRINKLE SHIELD TM (90) pour ACTIVER ou DESACTIVER &

tout moment avant qu'un programme ne soit termin&

La caracteristique WRINKLE SHIELD TM (90) est prereglee &

"OFF" (arret). Si selectionnee pour d'autres programmes, elle

restera sur "ON" (activee) la prochaine fois que ce programme

est selectionn&

Signal

Le signal est un signal sonore qui retentit Iorsque le programme

de sechage est termin& Appuyer sur le bouton SIGNAL pour

activer ou desactiver &tout moment avant qu'un programme ne

soit termin&

REMARQUE : Lorsqu'on selectionne la caracteristique WRINKLE

SHIELD TM (90) et que le signal sonore est active, un signal sonore

se fait entendre & intervalles de 20 minutes jusqu'& ce que I'on

retire les vetements ou jusqu'& ce que la caracteristique WRINKLE

SHIELD TM (90) soit terminee.

T_moins lumineux

D'autres temoins lumineux indiquent les reglages de programme,

de modificateur, d'option et de signal selectionn& L'affichage

montre le temps restant estime ou I'heure.

Cette caracteristique permet de verrouiller les reglages pour eviter

I'utilisation involontaire de la secheuse. On peut aussi utiliser la

caracteristique Control Lock (verrouillage des commandes) pour

eviter des changements involontaires de programme ou d'option

durant le fonctionnement de lasecheuse.

Pour activer la caract_ristique Control Lock (verrouillage

des commandes) alors que la s_cheuse est en marche :

Appuyer sur le bouton SIGNAL (signal sonore) pendant

3 secondes. Les commandes sont verrouillees Iorsqu'un

bip unique retentit et que le temoin de verrouillage des

commandes est allum&

Pour activer la caract_ristique Control Lock (verrouillage

des cornmandes) alors que la s_cheuse

est ARRETEE :

Lorsque lasecheuse est eteinte, il n'est pas necessaired'appuyer

sur le bouton POWERavant d'activer la caracteristique de

verrouillagedes commandes.

D_verrouillage :

Appuyer sur le bouton SIGNAL pendant 3 secondes pour

desactiver cette caracteristique.

REMARQUE : Lorsque la secheuse fonctionne et que le

verrouillage des commandes est active, il est possible d'arreter la

secheuse en appuyant sur le bouton START/PAUSE (mise en

marche/pause), mais elle ne peut pas etre remise en marche tant

que la commande n'est pas deverrouillee.

Sur les programmes automatiques, on peut modifier le

programme et le niveau de sechage & tout moment avant

d'appuyer sur START/PAUSE.

Avec les programmes minutes, on peut modifier les programmes,

ajuster la duree, ou changer le reglage de temperature &tout

moment avant d'appuyer sur START/PAUSE.

• Trois brefs signaux sonores retentissent si une combinaison

non disponible a ete selectionnee. La derniere selection ne

sera pas acceptee.

Changer de programme apr_s avoir appuy_

sur START/PAUSE

1. Appuyer sur POWER (mise sous tension). Ceci met fin au

programme en cours.

2. Selectionner le programme et les options desires.

3. Appuyer sans relAcher sur START/PAUSE (mise en marche/

pause). La secheuse recommence au debut du nouveau

programme.

REMARQUE : Si on n'appuie pas sur Start dans les 5 minutes

qui suivent le choix de programme, la secheuse s'arrete

automatiquement.

Changer les r_glages d'un programme minut_ en cours

de programme

Sur lesprogrammesminutes, il est possible d'effectuer lesactions

suivantes &tout moment :

• Regler la duree en appuyant sur les boutons More (plus) ou

Less (moins).

• Modifier le reglage de temperature en appuyant sur le bouton

Temp (temperature).

Page is loading ...

Whirlpool WED9270XL2 Owner's manual

Brand: Whirlpool

Model: WED9270XL2

Category: Electric laundry dryers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: Whirlpool WED9270XL2 Le manuel du propriétaire

Whirlpool WED9270XL2 Owner's manual

This manual is also suitable for

Whirlpool WED9270XL2 Owner's manual

in other languages

Related papers

Other documents