Kenmore 116-33720201 Owner's manual

Owner'sManual

ManualDelPropietario

VacuumCleaner

Aspiradora

Model, Modelo

116,33720

116.33721

116.3472O

116.34721

CAUTION:

Read and follow all

safety and operating

instructions before first

use of this product.

CUIDADO:

Lea y sigue todas las

instrucciones de operaci6n

y seguridad antes del uso de

este producto.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com

Part No. CQ1ZCAF3QUQG-KCO1ZCAF3QUQ

Printed in Mexico

Impreso en M_xico

Before UsingYour New Vacuum ........ 2

KenmoraVacuum Cleaner Warranty .... 2

ImportantSafety Instructions ........... 3

Parts and Features ................... 4

AssemblyInstructions ............... 5-6

Operating Instructions ................. 7

Pile HeightSelection and Setting ........ 7

Releasingthe Handle ................. 8

ON/OFF Switch ..................... 8

Attachments ..................... 9-10

AttachmentUse Chart ............... 10

VacuumingTips .................... 11

PerformanceFeatures ............... 11

Vacuum Cleaner Care ............... 12

Vacuum Storage ................... 12

Cleaning Exteriorand Attachments ..... 12

Dust BinCleaning ................ 13-14

Secondary FilterCleaning ............ 14

FilterChanging/Cleaning ............. 15

BeltChangingand AgitatorCleaning.. 16-17

Clog Removat ..................... 18

Motor Protector ..................... 18

AgitatorServicing................... 19

AgitatorAssembly .................. 19

LightBulb Changing ................. 20

Troubleshooting ..................... 21

Notes ............................... 22

Please read this guide. It will help you assemble and operate your new Kenmore vacuum in

the safest and most effective way.

For more information about vacuum cleaner care and operation, call your nearest Sears store.

You will need the complete model and serial numbers when requesting information. Your vacu-

um's model and serial numbers are located on the Model and Serial Number Plate.

Use the space below to record the model number and serial number of your new Kenmore

vacuum.

Model No.

Serial No.

Date of Purchase

Keep this book and your sales check (receipt) in a safe place for future reference.

LIMITED ONE YEAR WARRANTY ON KENMORE VACUUM CLEANER

This warranty is for one year from the date of purchase, and includes only private household

vacuum cleaner use. During the warranty year, when this vacuum cleaner is operated and

maintained according to the owner's manual instructions, Sears will repair any defects in

materiar or workmanship free of charge.

This warranty excludes vacuum bags, belts, light bulbs, and filters, which are expendable parts

and become worn during normal use.

For warrantyservice,retum this vacuum cleaner tothe nearest Sears Service Center in the

UnitedStates.

This warranty applies only while this product is in use in the United States. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state.

Seam, Roebuckand Co., D/817 WA, Hoffman Estates, IL 60179

Your safety is importantto us. To reduce the riskof fire, electricalshock, injuryto per-

sons ordamage when usingyour vacuum cleaner, follow basic safety precautions

including the following:

Reed this manual before assembling or

using your vacuum cleaner.

Use your cleaner only as described in

this manual. Use only with Sears recom-

mended attachments.

To reduce the risk of electrical shock -

Do not use outdoors or on wet surfaces.

Disconnect electrical supply before any

servicing or cleaning. Failure to do so

could result in electrical shock or per-

sonal injury.

Always turn cleaner off before unplug-

ging.

Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

Do not use with damaged cord or plug. If

cleaner is not working as it should, has

been dropped, damaged, left outdoors,

or dropped into water, return it to a

Sears Service Center.

Do not pull or carry by cord, use cord as

a handle, close door on cord, or pull

cord around sharp edges or corners.

Do not run cleaner over cord. Keep cord

away from heated surfaces.

Do not leave cleaner when plugged in.

Unplug from outlet when not in use and

before servicing.

Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

Do not handle plug or cleaner with wet

hands.

Do not put any objects into openings.

Do not use with any opening blocked;

keep free of dust, lint, hair and anything

that may reduce air flow.

Keep hair, loose clothing, fingers, and all

parts of body away from openings and

moving parts.

Do not use cleaner without dust bin

and/or filters in place.

Always clean the dust bin after vacuum-

ing carpet cleaners or freshener, pow-

ders and fine dust. These products clog

the filters, reduce airflow and can cause

damage to the cleaner. Failure to clean

the dust bin could cause permanent

damage to the cleaner.

Do not use the cleaner to pick up sharp

hard objects, small toys, pins, paper

clips, etc. They may damage the clean-

er or dust bin.

Do not pick up anything that is burning

or smoking, such as cigarettes, match-

es, or hot ashes.

Do not use cleaner to pick up flammable

or combustible liquids (gasoline, clean-

ing fluids, perfumes, etc.), or use in

areas where they may be present. The

fumes from these substances can create

a fire hazard or explosion.

Use extra care when cleaning on stairs.

Do not put on chairs, tables, etc. Keep

on floor.

You are responsible for making sure that

your vacuum cleaner is not used by any-

one unable to operate it properly.

SAVE THESE INSTRUCTIONS

Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your

cleaner is intended only for household use. Read this Owner's Manual carefully for

important use and safety information. This guide contains safety statements under

warning and caution symbols. Please pay special attention to these boxes and follow

any instructions given. WARNING statements alert you to such dangers as fire, elec-

trical shock, burns and personal injury. CAUTION statements alert you to such dan-

gers as personal injury and/or property damage.

It is important to know your vacuum cleaner's parts and features to assure its proper and safe

use. Review these before using your cleaner.

Item Part No. Part No.

In U.S. In Canada

Belt 20-5275 20-40096

Headlight Bulb 20-5240 20-40600

Primary Filter 20-82720

Exhaust Filter 20-86889 20o86889C

Hose

Dust Bin

Release

Handle --

Power

Cord.

Screw

Filter

Hose (Inside)

Holder

Cord Hook

Nozzle

Cover

Brush

Wand

Furniture

Guard

Retainer/

Carry Handle

-Dust

Bin

Exhaust

(Inside)

(Some Models)

Nozzle

Base

Nozzle Cover

Retainers

On/Off

Switch

Handle

Release

Model/Serial

Numbers

Tool

Motor

Protector

Sho_

Hose

EXTENSION HOSE KITS

SOME MODELS

Extension Hose

SOME NI()[)_ELS-

_FI _Adaptor

oor Brush

Wand

Before assembling vacuum, check the

PACKING LIST on the cover of the separate

Repair Parts List. Use this list to verify that

you have received all the components of

your new Kenmore vacuum.

ElectricalShock Hazard

Do not plugintothe electricalsupply

untilthe assembly iscomplete. Failure

to do so could result in electdcal shock

orinjury.

HANDLE ASSEMBLY

Remove the screw located just below the

top edge of the back of the vacuum.

Position the handle as shown in the illustra-

tion below.

While holding the power cord out of the way,

slide the handle into the opening at the top

of the vacuum.

Handle

Screw

Hole

Insert the screw so it passes through the

handle into the vacuum.

Begin to tighten the screw with your fingers.

It may be necessary to adjust the handle

slightly.

CAUTION

Do notovertighten.

Overtighteningcould stdp the screw

holes.

Do notoperate the cleaner withoutthe

screw in place.

Using a screw-

driver, tighten

the screw.

CORD ASSEMBLY

Make sure the quick release cord hook is in

the upright position. Remove the wire tie

from the power cord.

Lock the cord into

place by forcing it

into the locking

notch on the body Lockin

of the quick Notch

release cord hook

as shown. This

helps keep the

power cord out

from under the Power

vacuum cleaner

agitator.

Quick

Release

Curd

Power

Lower

Cord

Wrap the

power cord

around the

quick release

cord hook

and lower

cord retainer,

then lock the

power cord

plug onto the

power cord.

ATTACHMENT STORAGE

After the handle has been assembled to the

body and the power cord has been wrapped

around the cord hooks, the attachments can

be placed in their holders.

1. Snap the suction inlet end of the hose

into the back of the vacuum cleaner.

2. Place the hose behind the handle and

over the hose holder.

3. Place the hose in the front slot of the

tool holder, twisting and pushing down over

the short hose to assure a good connection.

4. Place the extension wand in the rear slot

of the tool holder.

5. Slide the crevice tool into the slot beside

the wand.

6. Place the dusting brush or combination

brush on the wand with the brush portion

up.

Handle-

Hose

Dusting

Brush

Extension

Wand

Inlet

Tool

Holder

Tool

HOWTO START

Quick

Release

Hook

1.Turn the quick

release cord

hook to either

side and down

to release the

power cord.

2. Release the power cord plug from the

power cord and pull the cord off the quick

release cord hook. Check to be sure the

power cord is still locked into the locking

notch in the quick release cord hook.

NOTE: To reduce the risk of electric shock,

this vacuum cleaner has a polarized plug;

one blade is wider than the other. This plug

will fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, con-

tact a qualified technician to install the prop-

er outlet. Do not change the plug in any

way.

Personal Injury and Product

Damage Hazard

• DO NOT plugin if switchis inthe

ON position.Personal injuryor

damage couldresult.

• DO NOT use outletsabove coun-

ters. Damage from cordto items in

surroundingarea couldoccur.

3. Plug the polarized power cord into a

120 Volt outlet located near the floor.

Models with no selector adjust automatically

for varying carpet heights.

SOME MODELS

To select a pile height setting:

Turn off cleaner. Select a pile height setting

by tilting the cleaner back until front wheels

are lifted slightly off the floor as illustrated.

Slide the adjustment lever to the correct

setting.

SUGGESTED PILE HEIGHT SETTINGS

You may need to raise the height to make

some jobs easier, such as scatter rugs and

longer pile carpets. Suggested settings are:

Models withtwo (2) positions:

HIGH: medium to long pile.

LOW: short to mediumpile.

Models with four (4) positions:

HIGH: shag carpet, long pile, plush, scatter

rugs

MED: medium to long pile.

LOW: short to medium pile.

EX LOW: very low pile.

Place unit in "HIGH" when usingattach-

ments to prevent possiblefloordamage.

AI-I'ENTION: Special care is required when

vacuuming certain types of carpet or floor

covering. Always check the carpet or floor

covering manufacturer's recommended

cleaning instructions before vacuuming.

Releasethehandlebyplacingyourfooton

thefootrestandpullbackonthehandle

untilit releasesfromitsuprightposition.

Foot Rest For

Handlq

SOME MODELS

Release the handle by pressing down on

the handle release pedal with your foot and

pulling back and down on the handle with

your hand.

r-7

Handle

Release Pedal

To start the vacuum cleaner, step on the

ON/OFF switch located on the back of the

vacuum. To stop the vacuum cleaner, step

on the switch a second time.

On/Off

PersonalInjuryHazard and Property

Hazard

DO NOT place hands or feet under-

neath the unitat any time. When using

attachments,the agitatorcontinues

rotating. Do notallow the cleaner to

remain in just one place for a periodof

time as the agitatormay damage the

floor surface. Avoid placingthe cleaner

on furniture, the fdnged area of rugs,

deep pile carpeting,or carpeted stairs.

The ideal positionforthe cleaner when

usingattachments is for the unitto be

on a level area with the handle in the

f_ position.

TO USE ATrACHMENTS

I CAUTION

DO NOT tip vacuum cleaner forwards or

sideways when using attachments.

The attachments will fit on the hose or the

wand. In addition, the dusting brush or

combination brush will also fit on the crevice

tool.

The hose and wand can be pulled off the

short hose by grasping the cuff and twisting

while pulling up.

! CAUTION

DO NOT pull the vacuum cleaner

around the room by the hose.

Property damage could result.

The attachments can be added to the hose

if the item to be cleaned is not far from the

creaner. The hose on some moders will

expand.

NOTE: When cleaner is turned on, the hose

on some models will have a tendency to

collapse due to suction of the cleaner.

if more reach is needed, the wand can be

attached to the hose and the attachments

can be added to the wand.

When using attachments, be careful

not to overextend the hose length

when reaching. Trying to reach

beyond the hose reach could cause

the cleaner to tip over.

SOME MODELS

An extra wand, without tabs, is included.

This extra wand can be added to the

wand with tabs for extra reach. Insert

wand and twist a quarter of a turn to

secure fit.

Crov, o,-- o,-

_Dusting Brush Wand

(Some Models) _

Combination

Brush (Some

Models)

If the dusting brush/combination brush is

being used and more distance is

needed, the crevice tool can be added to

the wand, then the dusting

brush/combination brush can be added

to the crevice tool.

TO STORE

A'I-FACHMENTS

Return the hose to its position on the

short hose and the attachments to their

holders.

Attachmentsused in dirtyareas, such

as under a refrigerator,shouldnot be

used on othersurfaces untilthey are

washed. They could leave marks.

When using the regular hose or with

the extension hose attached, the

cleaner should be on a solid surface

on the same level or below the level of

the user's feet. DO NOT use the hoses

when the cleaner Is above the level of

I the user's feet.

EXTENSION HOSE

SOME MODELS

Some models include an extra hose which

connects to the stretch hose on the vacuum

for a longer cleaning reach.

Unit Hose _ Extension Hose

Insert the two tabs on the end of the

extension hose into the two "J" shaped slots

on the unit hose and twist to connect.

All attachments and the wand can be

attached to the open end of the hose.

FLOOR BRUSH AND WAND

SOME MODELS

Some models have an extra brush and wand

for cleaning bare floors. Twist one end of the

adaptor into the floor brush and the other

end into the straight wand. Connect the

straight wand to the telescopic wand and

then to the vacuum hose or extension hose.

(}J

A'I-FACHMENT

DUSTING BRUSH <_

CREVICE TOOL ¢_ _

COMBINATION BRUSH

Handi-Mate ® Jr.

Fumiture*

CLEANING AREA

Between

Cushions*

Drapes* Stairs

X X

Walls

The motor protector may open when using attachments or when cleaning new carpet due to

reduced air flow caused by the attachments themselves or by new carpet fuzz filling the bag

quickly.

*Always clean attachments before using on fabrics.

Personal InjuryHazard

Use care Ifvacuum cleaner Is placed

on stairs.If itfalls, personal injuryor

propertydamage couldresult.

Carpet edges

Guide either side or the front of the nozzle

along a baseboard. The full length brushes

help remove trapped dirt at carpet edges.

Stairs

Put handle in ful! upright position. Use the

crevice tool or dusting brush. Set the On/Off

switch to ON.

MOTOR PROTECTION

SYSTEM

Thermal Protector

This vacuum has a thermal protector which

automatically trips to protect the vacuum

from overheating. If a clog prevents the

normal flow of air to the motor, the thermal

protector turns the motor off automatically to

allow the motor to cool in order to prevent

possible damage to the vacuum.

To correct problem: Ifthis occurs, turn the

vacuum off and unplug the power cord from

the outlet to allow the vacuum to cool and

the thermal protector to reset. Check for

and removeclogs, ifnecessary. Alsocheck

and clean/replace any cloggedfilters. Wait

approximatelythirty (30) minutesand plug

the vacuum in and turn back on to see ifthe

motorprotectorhas reset.The motor

protectorwill not reset if the vacuum is not

tumed offeven if the vacuum hascooled

down.

PERFORMANCE

INDICATOR

SOME MODELS

When the unit is running with normal air

flow, the light on the performance indicator

is off. The light comes on whenever the

airflow becomes blocked. If that occurs,

check the dust bin, clean/replace clogged

filters, and check other possible clog

locations shown in CLOG REMOVAL.

To correct problem: See the TROUBLE-

SHOOTING chart.

NOT,Te f

light may

also come on

when using

attachments,

due to

reduced

airflow

through the

attachment.

Alwaysfollowallsafetyprecautionswhen

cleaningandservicingthevacuum

cleaner.

ElectricalShockAndPersonalInjury

Hazard

Disconnectelectricalsupplybefore

servicingor cleaningthe unit.Failure

to do so could resuRin electricalshock

or personal injuryfrom cleanersud-

denlystarUng.

Gather the power cord and wrap it loosely

around the quick release cord hook and

lower cord retainer.

Store the cleaner in a

dry, indoor area, on

the floor with the

Quick

Release handle locked in the

Cord upright

Hook _ position.

Power

Lower

Cord

Unplug cord from wail outlet.

WARNING

dcal Shock And Personal Injury

Hazard

Wrappingthe cord too tightly puts

stresson the cord and can cause cord

damage. A damaged cord isan electri-

cal shockhazard and could cause per-

sonal injuryor damage.

DO NOT ddpwater on cleaner.

To reduce static electricity and dust build-

up, wipe outer surface of cleaner using a

clean, soft cloth that has been dipped in a

solution of mild liquid detergent and water,

then wrung dry. Wipe dry after cleaning.

Wash attachments in warm soapy water,

rinse and air dry. Do not clean in dishwash-

or.

Do not use attachments if they are

wet. Attachments used in dirty areas,

such as under a refrigerator, should

not be used on other surfaces until

they are washed. They could leave

marks.

Alwaysemptythe dust binwhen dirtlevel

reachesthe "MAX FILL" line.

TO REMOVE DUST BIN

! WARNING

Always unplugpower cord fromelectri-

cal outletbefore performingany ser-

vice on vacuum.

Lift dust bin han- DustBin _h_

Release

die located at the Handle --

top of the dust

bin. Dust

Bin --

Pull the handle

forward and lift

dust bin up and

out of the vacu-

um cleaner.

Seoondar,I

Remove any

clogs that

might be

located in the

dust bin port

or the sec-

ondary filter.

TO EMPTY DUST BIN

Turn This Direction Closed

To Open For Emptying (for Use)

Open

(For Emptying)

Rotate dust bin lid assembly counterclock-

wise as indicated on the lid and lift off.

Pour dust bin contents

into a trash container.

TO CLEAN FILTER

The filter may be

cleaned by

tapping it on a firm

surface or by

rinsing it under a

faucet. See Filter

Changing/Cleaning

section Rinse with

water only, do not

use any detergent or

_ Filter

Cover

soap. Allow the filter to dry for 24 hours

before putting it back into the vacuum.

TOREPLACEDUSTBIN

Turn This Direction Open

TO Close For Use (For Emptying)

Closed

(ForUse)

Place dust bin lid assembly back onto top of

dust bin. Align lid marks with bin marks as

shown above in Open (For Emptying).

Rotate lid clockwise while pressing down-

ward so that marks align as shown in

Closed (For Use).

Place dust bin

back into vacuum

cleaner by insert-

ing the bottom first

and tilt back with

the dust bin han-

dle raised.

Dust Bin

Release

Dust

Bin

Push forward and

lower the dust bin

handle to lock

dust bin in place.

Check secondary filter 'frequently and clean

when dirty.

Remove the dust bin as outlined in the

DUST BIN CLEANING section.

To clean filter screen wipe screen with a dry

cloth.

NOTE: Filter screen is not removable.

Replace the dust bin as outined in the

DUST BIN CLEANING section.

Secondary

WARNING

PRIMARY FILTER

Check primary filter frequently and clean

when dirty.

TO REMOVE PRIMARY FILTER

Remove the dust bin and dust bin lid

assembly as outlined in the DUST BIN

CLEANING section. While holding the pri-

mary filter over a trash container grasp filter,

rotate and lift off.

Clean primary filter by

gently tapping over a trash

container. Locking

Tap on several

sides to

ensure best

cleaning. Cover

Slot

Rinsewith water onlyas needed (see Dust

Bin Cleaning).

When cleaning the filter no longer restores

vacuum suction to full power you need to

replace the filter.

TO REPLACE PRIMARY FILTER

Make sure that the slots

of the filter line up with

the locking tabs on the

filter cover. Replace filter

and rotate filter until

slots lock onto tabs

in cover.

Cover

Slot

Tab

Note: Under normal use and care, your filter

can be expected to last up to 3 years.

Re-attach the filter cover and filter to dust

bin (see Dust Bin Cleaning). Place dust bin

back into cleaner.

EXHAUST FILTER

FOAM

Press inward on each side of

exhaust filter cover and pull out

to remove from vacuum

Press

cleaner. Inward

Exhaust

Remove the

frame and filter.

Push only on

filter frame, not

on filter itself.

Filter

Frame

Filter

Wash the exhaust filter in warm soapy

water; rinse and dry thoroughly by squeez-

ing the filter in your hand and letting it air

dry.

DO NOT wash in the dishwasher.

DO NOT installdamp.

Replace the exhaust filter, carefullyposition-

ing it so that it fits into the frame.

Exhaust

Filter

Cover

Replace the

exhaust filter

cover by placing

tabs in slots and

pushing in until

cover snaps into

place.

WARNING

ElectricalShock Or Personal Injury

Hazard

Disconnectelectrical supplybefore

servicingor cleaningthe unit. Failure

to do so couldresultin electricalshock

or personal injuryfrom cleaner sud-

denlystarting.

Frequently check and remove hair, string

and lint build-up in the brush area. If build-

up becomes excessive, follow the steps

below. Should the belt become loose or

should it break, follow the Belt Removal

Instructions.

TO REMOVE NOZZLE COVER

Disconnect electrical supply.

To protect the floor surface, always place

paper under the nozzle any time the nozzle

cover is removed.

Release the nozzle c_)ver by rotating the

nozzle cover retainerg to the UNLOCK

position. Grasp back of nozzle on each side

and lift up to remove it from nozzle cover.

Nozzle

Cover

Carefully remove any residue that may exist

in the belt area.

Personal InjuryHazard

Always unplugthe vacuum cleaner

before cleaningthe brusharea as agi-

tator may suddenlyrestart. Failureto

do so can resultin personal injury.

TO REMOVE BELT/CLEAN

AGITATOR

Agitator

Position hands on the agitator. If the belt is

still attached to the agitator, there will be

tension on it.

Carefully lift the right end of the agitator and

then lift the left end.

Remove the worn or broken belt from the

motor drive shaft.

Personal Injury Hazard

Be careful when removingthe agitator

as the belt tensionis high.Failure to

do so could resultin personalinjury

fromthe agitator releasingquicklyand

snappingaway.

Remove the agitator to check for string and

hair build-up.

NOTE: In order to keep cleaning efficiency

high and to prevent damage to your vacu-

um, the agitator must be cleaned every time

the belt is changed,

The agitator must also be cleaned accord-

ing to the following schedule:

Vacuum Use

HEAVY -

(used daily)

MODERATE-

(used 2-3 times/week)

LIGHT-

(used 1time/week)

Clean Aaitator

every week

every month

every 2months

Cap

Cut oft any carpet

pile, hair or lint

entangled around

the agitator and

remove any string

or debris located

near the end

caps.

TO REPLACE BELT

Shaft

_"New

Belt

Pulley

Seat left end of agitator into nozzle base. To

seat agitator end, place rounded portion of agi-

tator end cap down into slot in nozzle base.

Loop the new belt on the motor shaft.

NOTE: Use Belt #20-5275

Loop the other end of belt onto the belt

pulley on the right end of agitator.

Pull right end of agitator forward and seat it

into nozzle base

Agitator Nozzle

Base

End

Cap

--Base

Slot

Press firmly, checking to see that each

end is completely inserted.

Agitator

Check to see that the belt is centered on the

belt pulley and that the agitator turns freely.

Nozzle I

Cover

Nozzle Cover

Retainers

Make sure the nozzle cover retainers are in

the UNLOCK position. Hook the front of the

nozzle cover on to the nozzle base and

rotate downward. Once in place, rotate the

nozzle cover retainers to the LOCK position.

Electrical Shock Or Personal Injury

Hazard

Disconnectelectdcal supplybefore

servicingor cleaningthe unit, Failure

to do so couldresult in electricalshock

or personal injuryfrom cleaner sud-

denly starUng.

Always follow all safety precautions when

cleaning and servicing the vacuum cleaner.

If the cleaner does not seem to have ade-

quate suction, first check if the dust bin is

full or if a filter is clogged. See DUST BIN

CLEANING and FILTER CLEANING /

CHANGING.

If the dust bin and filter areas are free of

clogs, check the hose area. Remove the

suction inlet by depressing the two tabs that

secure it to the back of the vacuum and

check for clogging in this area.

Hose

Tabs

Inlet

Tool

Motor

Hose

Replace the suction inlet and remove the

other end of the hose from the tool holder.

Plug in the vacuum and turn it on. While

running the vacuum cleaner, stretch the

hose in and out to remove the clog.

Turn the unit off and unplug the unit.

If the clog still exists, pull the short hose out

of the tool holder and inspect the short

hose.

Remove any visible clogs.

Motor _-_ 1

Protector _ ;___

NOTE: Do not block motor protector.

This vacuum has a motor protector by-pass

valve which automatically opens to provide

cooling air to the motor when a clog

prevents the normal flow of air. If the by-

pass valve opens to prevent motor

overheating and possible damage to the

vacuum, a change of sound will be noticed

as air rushes through the valve opening. If

this occurs, turn the vacuum off and unplug

the power cord from the outlet. Then check

for clogs as described under the CLOG

REMOVAL section.

The motor protector by-pass valve may open

when using attachments or when cleaning

new carpet, due to reduced air flow caused

by the attachments themselves or by new

carpet fuzz filling the dust bin quickly.

ElectricalShockOr PersonalInjury

Hazard

Disconnectelectricalsupplybeforeser-

vicingor cleaningthe unit. Failureto do

socould result inelectricalshockor

personalinjuryfromcleanersuddenly

starting,

TO CHECK AGITATOR

Base Belt Guard

Turn the vacuum

over to check for

worn brushes.

When brushes are

worn to the level of

the base belt guard,

replace the agitator.

TO REPLACE AGITATOR

Remove the nozzle cover and agitator. See

BELT CHANGING AND AGITATOR

CLEANING.

Replace agitator with a new one.

Reassemble the belt, agitator and nozzle

cover. See BELT CHANGING AND

AGITATOR CLEANING.

Belt Pulley

End Cap

Agitator Unit

End Cap

SOME MODELS

CAUTION

ElectricalShock Or Personal Injury

Hazard

Disconnectelectrical supplybefore

servicingor cleaningthe unit. Failure

to doso couldresultin electricalshock

or personal injuryfrom cleaner sud-

denlystarting.

Disconnect electrical supply.

To access the light bulb, remove the screw

which secures the light lens to the vacuum.

Remove the lens.

Screw Push Here

ToRemove

Remove the light bulb by pushing the bulb in

while turning counterclockwise to release

from the slot. Pull the light bulb straight out.

Do notuse e bulb rated over 130 V

AC-15 W. Duringextended use, heat

from the bulbcouldoverheat surround-

ing plasticparts.

To replace the light bulb, carefully insert and

turn clockwise to fit securely into slot.

NOTE: See Parts and Features for Bulb

number.

I CAUTION

Do not plug in or turn on until corn-

pletely reassembled.

Position the light lens back on the vacuum.

Replace the light lens screw.

Page is loading ...

Kenmore 116-33720201 Owner's manual

Related papers

Other documents