DUROMAX DS7000Q Owner's manual

DS7000Q GENERATOR

This manual provides information regarding the operation

and maintenance of these products. We have made every

effort to ensure the accuracy of the information in this

manual. We reserve the right to change this product at

any time without prior notice.

5800 Ontario Mills Pkwy

Ontario, CA 91764 USA

www.duromaxpowerequipment.com

Call our Customer Care Team Toll Free 8-5pm PST Mon-Fri

844-DUROMAX

User Manual

REV: DS7000Q-05252018

CONTENTS

1.

Introduction .................................................................................................................... 6

General Safety Procedures ........................................................................................... 7

Quick Start Guide .......................................................................................................... 10

Generator Components ............................................................................................... 12

Package Contents ......................................................................................................... 14

Introduction

3.

Checking the Oil ........................................................................................................... 20

Check the Fuel Level .................................................................................................... 21

Starting the Generator ................................................................................................. 22

Starting the Generator - Remote Start ...................................................................... 24

Starting the Generator

2.

Adding Oil ...................................................................................................................... 16

Adding Diesel ................................................................................................................. 17

Grounding the Generator ........................................................................................... 18

Generator Setup

4.

AC Usage ......................................................................................................................... 28

Connecting a Load to the Generator ........................................................................... 30

Voltage Selector Switch ................................................................................................ 31

DC Usage ........................................................................................................................ 32

Using the Generator

3

CONTENTS

4

5.

6.

7.

Maintenance Schedule .................................................................................................. 36

Maintenance Log ........................................................................................................... 37

Checking the Oil ............................................................................................................ 38

Changing the Oil ............................................................................................................. 39

Cleaning the Air cleaner ................................................................................................ 40

Specications .................................................................................................................. 42

.......................................................................................................................... 50

Basic Troubleshooting .................................................................................................. 44

Changing / Inspecting the AVR .................................................................................... 46

Maintenance and Care

Warranty

Troubleshooting

8. .................................................................................................. 54

Contact Information

INTRODUCTION

Notice Regarding Emissions

DuroStar has cemented its reputation as one of the markets leading power equipment companies

who are headquartered in the US. All of our products are manufactured to the strictest guidelines

and go through countless testing in all phases of production.

Evolving our strong engine line, DuroStar has complemented its oerings to include Pressure

Washers, Water Pumps, Engines and now oering V-Twin engines. Reliability is the highest

standard we hold ourselves to, whether its powering a heater during a winter storm that knocks

out power, dewatering a ooded property, or washing away a deck for the summer season

Engines that are certied to comply with U.S. EPA emission regulations for SORE (Small o Road

Equipment), are certied to operate on regular diesel, and may include the following emission

control systems: (EM) Engine Modications and (TWC) Three-Way Catalyst (if so equipped).

6

STOP

Please do not return

to store.

Durostar representatives are ready to help you

with any questions, concerns, or issues about your

new product. We can guide you through assembly,

start up, and how to operate your new generator.

We want you to be able to put your new generator

to use right away!

CALL US BEFORE YOU CONSIDER

RETURNING THE PRODUCT!

1-844-DUROMAX

TOLL FREE

SAFETY ALERT SYMBOL

DANGER: This generator produces poisonous carbon monoxide gas when running. This

gas is both odorless and colorless. Even if you do not see or smell gas, carbon monoxide

may still be present. Breathing this poison can lead to headaches, dizziness, drowsiness,

and eventually death.

●Use outdoors ONLY in non-conned areas.

●Keep several feet of clearance on all sides to allow proper ventilation of the generator.

WARNING: The exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING: This generator produces heat when running. Temperatures near exhaust can

exceed 150°F (65°C).

●Do not touch hot surfaces. Pay attention to warning labels on the generator denoting

hot parts of the machine.

●Allow generator to cool several minutes after use before touching engine or areas

which heat during use.

The safety alert symbol is used with one of the safety words (DANGER,

CAUTION, or WARNING) to alert you of hazards. Please pay attention to

these hazard notices both in this manual and on the generator.

GENERAL SAFETY PROCEDURES

7

Please familiarize yourself with the following safety symbols and words:

●DANGER: Indicates a hazard that will result in serious injury or death if instructions are not

followed.

●WARNING: Indicates a strong possibility of causing serious injury or death if instructions are not

followed.

●CAUTION: Indicates a possibility of personal injury or equipment damage if instructions are not

followed.

WARNING: This generator may emit highly ammable and explosive diesel vapors, which

can cause severe burns or even death. A nearby open ame can lead to an explosion

even if not directly in contact with fuel.

●Do not operate near an open ame.

●Do not smoke near generator.

●Always operate on a rm, level surface.

●Always turn generator o before refueling.

●Allow generator to cool for at least 2 minutes before removing fuel cap. Loosen cap

slowly to relieve pressure in tank.

●Do not overll fuel tank. Fuel may expand during operation. Do not ll to the top of

the tank.

●Always check for spilled fuel before operating.

●Empty the diesel tank before storing or transporting the generator.

●Before transporting, turn fuel valve to the o position and disconnect the spark plug.

WARNING: This generator produces a powerful voltage, which can result in electrocution.

●ALWAYS ground the generator before using it (see the “Grounding the Generator”

portion of the “PREPARlNG THE GENERATOR FOR USE section).

●Generator should only be plugged into electrical devices, either directly or with an

extension cord. NEVER connect to a building electrical system without a qualied

electrician. Such connections must comply with local electrical laws and codes. Failure

to comply can create a backow of power, which may result in serious injury or death

to utility workers.

●Use a ground fault circuit interrupter (GFCI) in highly conductive areas such as metal

decking or steel work. GFCls are available in-line with some extension cords.

●Do not use uncovered in rainy or wet conditions.

●Do not touch bare wires or receptacles (outlets).

●Do not allow children or non-qualied persons to operate.

GENERAL SAFETY PROCEDURES

8

In addition to the above safety notices, please familiarize yourself with the safety and

hazard markings on the generator.

GENERAL SAFETY PROCEDURES

9

QUICK START GUIDE

Add diesel

The fuel cap is located on top of the fuel tank. Fill the tank

with fresh diesel uel. The tank is full when you see fuel in

the bottom of the fuel lter cup. DO NOT overll the tank.

2.

Run/Stop Switch

The Run/Stop Switch is located inside the mainentance

door above the oil ll. Flip the switch to the right to allow

the unit to run.

Add oil

The oil ll cap is located on the lower engine block inside

the maintenance door. Remove the oil ll cap and ll with

15w40 diesel oil.

1.

Turn breaker o

The breaker is located on the right side of the front power

panel. Flip the breaker down to prevent accidental load

when starting the generator.

3.

10

4.

Check power indicator

The power indicator is located to the right of the keyswitch.

Ensure the power indicator is lit before powering

appliances.

8.

Connect devices

Connect your devices to the receptacles on the front panel.

Start with the largest loads rst.

10.

Start generator

The key switch is located on the left side of the front power

panel. Insert the key and turn to the start position to start

the generator. Allow the key to return to the run position

once started.

7.

Turn breaker on

The breaker is located on the right side of the front power

panel. Flip the breaker up to allow power to ow to the

receptacles.

9.

11

GENERATOR COMPONENTS

12

8. Battery 5. Oil Fill

4. Air Filter

3. Lifting Ring

2. Fuel Cap

6. Oil Drain

7. Stop / Run

Switch

1. Muer - Reduces engine emissions and reduces noise

2. Fuel Cap - Allows access to ll the diesel tank.

3. Lifting Ring - Use to lift the generator with a truck crane or winch.

4. Air Filter - a removable element that cleans the air going into the engine.

5. Oil Fill and Dipstick - Use to add or check the engine oil.

6. Oil Drain - Use to remove the engine oil during regular oil changes.

7. Stop/Run Switch - To the right for Connect a ground wire here to properly ground the

generator.

8. Battery - 12V DC 7ah Battery that powers the Electric Start System.

9. Engine Switch – 3 Position Switch to “Start”, “Run”, or turn “O” the generator.

10. Low Oil Alert - Will light if the engine shuts down or will not start due to low oil.

11. Volt Meter - Provides reading of voltage output.

11. Power Indicator - Use to conrm the generator has power output before connecting devices.

1. Muer

14. Circuit Breaker

13. Power Boost

12. Voltmeter

11. Power Indicator

10. Low Oil Alert

12. Volt Meter - Provides reading of voltage output.

13. Power Boost – DuroStar exclusive Power Boost doubles the amperage available in “120v Only”

for heavy loads like RV air conditioners.

14. Circuit Breaker - Resettable switch that protects the generator from electrical overload.

15. 12v DC Charging Posts – DC Output for charging batteries or running small DC powered items.

16. Ground Terminal - Connect a ground wire here to properly ground the generator.

17. 120/240v 4-Prong Twist Lock - Use to connect electrical devices that run 120 or 240 Volt, 60Hz,

single phase, AC current (NEMA L14-30).

18. 120v 3-Prong Twist Lock - Use to connect electrical devices that run 120 Volt, 60 Hz, single

phase, AC current (NEMA 6-20).

19. 120v 3-Prong GFCI Receptacle - Use to connect electrical devices that run 120 Volt, 60 Hz,

single phase, AC current (NEMA 5-20).

13

9. Engine

Switch

19. 120V

3-Prong

Receptacle

18. 120V 3-Prong

Twist Lock

17. 120/240

4-Prong Twist

Lock

16. Ground

Terminal

15. 12V DC

Charging Posts

PACKAGE CONTENTS

Your generator comes with the items listed below. Please check to see that all of the following

items are included with your generator.

●Note: Actual tools may dier in appearance or design from image shown.

Double Sided

Screw Driver

Oil Funnel w/ hose

Spanner

DC Charge Cables

Spark Plug Wrench

Plug Ends

Phillips and slot blade

screwdriver used for generator

maintenance.

Used to add oil to the

generator without messy spills.

Assorted wrenches used in

generator maintenance and

assembly. Commonly 8mm,

10mm, 13mm, and 15mm.

Used in conjunction with the

charging posts to charge 12v

automotive style batteries or

small DC appliances.

Used in spark plug

maintenance, inspection, and

installation.

Plug heads for the receptacles

found on the generator are

included to make or rewire

your own cords.

14

GENERATOR SETUP

Proper setup of your generator will get you going as soon as possible while making sure you and

your equipment are safe and cared for.

-20 20 40 60 800 100 F

-30-40 -10 0 10 20 30

-20 40 C

30

10W-30

ENVIRONMENTAL TEMPERATURE

5W-30

SAE

GENERATOR SETUP

Add oil

The generator requires engine oil to operate properly. The generator, when new from the package

contains no oil in the crankcase*. You must add the proper amount of oil before operating the

generator for the rst time. This amount is equal to the oil capacity of the engine crankcase:

WARNING: Do not apply engine oils with additives or 2-stroke engine oils. They don’t have

enough lubrication, and may shorten the engine’s service life.

a. Make sure the generator is on a level surface.

b. Unscrew the oil ller/dipstick cap from the engine .

c. Using a funnel, add the appropriate amount of oil

into the crankcase. You will know the crankcase is

full when the oil level has reached the lower lip of

the opening you have just poured the oil into.

d. Replace oil ller cap.

1.

Step 1 - Adding Oil

Engine oil recommended: SAE 15W-40. Viscosity varies with

regions and temperatures. Choose your oil viscosity using the

chart to the left.

* A small amount of oil from factory testing may be present on

arrival.

Model Number DS7000Q

Engine Oil Capacity 54 . oz (1.6L)

16

WARNING: DO NOT overll the crankcase. This

may damage the motor and shorting overall life

of your generator.

WARNING: Diesel and fuel fumes are highly ammable.

●Do not ll tank near an open ame.

●Do not overll. Always check for fuel spills.

17

Step 2 - Adding Diesel

Add Diesel

a. Make sure the generator is on a level surface.

b. Unscrew fuel cap and set aside (NOTE: the fuel cap

may be tight and hard to unscrew).

c. Slowly add diesel to the fuel tank. Be careful not

to overll.

d. The fuel gauge on the top of the fuel tank indicates

how much diesel is in the generator fuel tank.

e. Replace fuel cap and wipe up any spilled diesel

with a dry cloth.

NOTE: Fuel can expand. Do not ll the fuel tank

to the very top. Leave a minimum of 1.5 in of open

space.

IMPORTANT:

●Never use an oil/diesel mixture. Never use old fuel.

●Avoid getting dirt or water in the fuel tank.

●Fuel can age in the tank and make it hard to start up

the generator in the future.

●Never store generator for extended periods of time

with fuel in the tank.

2.

Model Number DS7000Q

Fuel Tank Capacity 3.8 US Gallons (14.5L)

WARNING: DO NOT overll the crankcase. This

may damage the motor and shorting overall life

of your generator.

GENERATOR SETUP (CONTINUED)

Attach grounding wire

a. Ground the generator by tightening the grounding

nut against a grounding wire.

b. Connect the other end to a copper or brass

grounding rod that’s driven into the earth.

A generally acceptable grounding wire is a No. 12 AWG

(American Wire Gauge) stranded copper wire.

Grounding codes can vary by location. Please contact a local

electrician to check the grounding regulations for your area.

1.

Step 3 - Grounding the Generator

WARNING: Failure to properly ground the generator can result in electrocution.

18

19

STARTING THE GENERATOR

If this is not your rst time using the generator there are still steps you should take to prepare it for

operation each time you use it.

IMPORTANT: At this point you should be familiar with the procedures described in the rst

portion of this section entitled “GENERATOR SETUP” If you have not yet read this section, go

back and read it now.

Step 1 - Check the oil

Check the oil

The generator is equipped with an automatic shuto to

protect it from damage due to low oil. Nonetheless, you

should check the oil level of the engine before each use to

ensure that the engine crankcase has a sucient amount.

To check the oil level:

a. Make sure the generator is on a level surface.

b. Unscrew the oil ller/dipstick cap.

c. With a dry cloth, wipe the oil o of the stick on the

inside of the cap.

d. Insert the dipstick as if you were replacing the

cap and then remove again. There should now be

oil on the stick. If there is no oil on the stick, or oil

only at the very end of the stick, you should add

oil until the engine crankcase is lled (see “Adding

Oil” portion of the “Maintenance” section).

e. Be sure to replace the cap when nished checking

oil.

NOTE: The oil capacity for your generator can be found in

the “Specications” section of this manual.

1.

20

BEFORE YOU START YOUR GENERATOR

Page is loading ...

DUROMAX DS7000Q Owner's manual

DUROMAX DS7000Q Owner's manual

Related papers

Other documents