Novus NV-DVR4516(S)/DVD User manual

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

1

NV-DVR4508(S)/DVD

NV-DVR4516(S)/DVD

U ser’s ma n ua l

(s h o rt fo rm )

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

2

NV-DVR4508(S)/DVD

NV-DVR4516(S)/DVD

U se r ’s ma n ua l

(s h o rt fo rm )

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

4

COMMETS AD WARIGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of following directives and

national regulations implementing the directives:

• Electromagnetic compatibility EMC 2004/108/EC.

• Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well

as 75VDC and 1500VDC.

WEEE Directive 2002/96/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic

Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly,

you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for the

waste electrical and electronic equipment for recycling purpose. For more information about recycling

of this product, please contact your local authorities, your household waste disposal service or the shop

where you purchased the product.

RoHS Directive 2002/95/EC

Concerning for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, were designed and manufactured in compliance with

mentioned regulation. Simultaneously, we claim that our products were tested and do not contain

hazardous substances exceeding limits which could have negative impact on human health or natural

environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

The manufacturer is not responsible for defects and damages resulted from improper or inconsistent

with user’s manual installation of the device in the system.

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

5

SAFETY REQUIREMETS

ATTETIO!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN

PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS

MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY OF THE

MANUFACTURER FOR THE RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. The installation of NV-DVR4508/DVD, NV-DVR4516/DVD should be done by a qualified service

person or a professional safety system installer.

2. Recorders mustn’t be placed in places where ventilating holes are partially or fully covered.

3. User’s interference inside the device is not allowed and is unnecessary as it does not have any

systems which require adjusting or which are suitable for self-repair. You mustn’t dismantle the

recorder or remove any single fastening screws. If any repairs are necessary contact the service.

The device must be taken care of and protected against any mechanical damage.

4. The recorder has to be protected against humidity and dust. In case the recorder had a contact with

water react immediately: switch off the power supply and contact the authorised Novus service. If

the device gets dirty it might get damaged or electrocute someone.

5. The device can be cleaned only with a damp cloth after the power supply has been switched off.

Avoid strong detergents (liquids and sprays). Mild detergents can be used if the recorder becomes

very dirty.

6. Power supply unit cords and signal cords should be laid in a way that eliminates the risk of

mechanical damage; special attention should be paid to the plug. Be careful not to overload sockets

and extension cords so that there is no fire.

7. To avoid recorder’s damage vision and control signals should be equipped with systems protecting

against disturbances, over voltage and atmospheric discharge that are in compliance with Polish

regulations. It is also advised to use ground loop isolators.

8. The device mustn’t be used in conditions which do not fulfil operating requirements as far as power

supply, relative humidity or air temperature are concerned.

9. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a

metal object gets inside the device contact the authorised Novus service immediately.

10. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other

media occurred during the usage of the product.

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

6

TABLE OF COTETS .............................................................................................................. 6

1. FOREWORD IFORMATIO ............................................................................................. ..7

1.1. Main Characteristics ............................................................................................................ 7

1.2. Technical Specifications .................................................................................................. ...8

2. STARTIG THE DEVICE ....................................................................................................... 9

2.1. Getting the device ready to work ...................................................................................... 9

2.2. Electrical connection and other back panel’s elements ................................................... 10

2.3. Connecting external devices .......................................................................................... 12

2.4. Front panel description ................................................................................................... 13

2.5. HDD installation ............................................................................................................. 17

3. RECORDER’S MEU ............................................................................................................ 18

4. RECORDER’S OPERATIO ................................................................................................ 19

4.1. Live monitoring .............................................................................................................. 19

4.2. Playing recorded video ................................................................................................... 20

TABLE OF COTETS

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

7

1. FOREWORD IFORMATIO

1.1. Main characteristics

• Quadruplex mode. Simultaneous: recording, playback, live monitoring (spot monitors) and

network connection.

• Operating system based on Linux

• Real-time display

• Recording speed up to 100 images per second

• Efficient compression algorithm based on MPEG-4 standard

• Recording resolution: - 352 x 288,

- 704 x 288,

- 704 x 576

• Max. total HDD’s capacity 4 TB

• Possibility of setting different recording speed and quality for each camera

• Advanced recording schedule

• Advanced motion detection

• Pre- and post alarm function

• Recording up to 4 audio channels

• Advanced search modes

• PTZ camera control using recorder or network applet.

• Remote control of NOVUS® compact cameras using RS-485 standard

• Protocols: Novus-C, N-Control, Pelco-D

• Fully-compatible with NV-KBD30 keyboards

• USB Mouse

• DVD-RW Drive

• Files backup available through network, USB port, on HDD or CD/DVD disc

• Remote controller

• Network compatible (connection with other recorders, e-mail messages in case of alarm)

• Software: N-Viewer4000 (administration, monitoring and displaying records)

• Self-diagnostics with an automatic notification,

• Covert camera function

• Power supply: 230 VAC

FOREWORD IFORMATIO

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

8

FOREWORD IFORMATIO

1.2. Technical specifications

Model NV-DVR4508(S)/DVD NV-DVR4516(S)/DVD

Operation Mode Quadroplex

Operating System Linux

Video Inputs 8 x BNC, loop-through 16 x BNC, loop-through

Video Outputs Main Monitor (1 x BNC, 1 x VGA, 1 x S-Video),

Spot Monitor (2 x BNC)

Alarm Inputs 8 16

Alarm Outputs 8 16

Audio Inputs / Outputs 4 x RCA / 1 x RCA

Recording Speed up to 100 fps (352 x 288), up to 50 fps (704x 288), up to 25 fps (704 x 576)

Compression Algorithm MPEG-4

Recording Resolution 352 x 288, 704 x 288, 704 x 576

Recording Mode Continuous, Event (Alarm, Motion Detection)

Display Speed 200 fps (live display) 400 fps (live display)

Display Screen 1, 4, 6, 8, 9, sequence, user defined digital zoom (x2) 1, 4, 6, 9 ,13, 16, sequence, user defined digital zoom (x2)

Motion Detection Adjustable zone’s size and sensitivity grid 16x16 (enable for each camera)

Video Loss Detection Yes

Schedule Recording daily and weekly schedule different for each camera, combination of individual recording modes

Recording Data Search By date/time or events (alarms, motion detection, system events)

Event Log up to 60 000 000 events

Time Synchronisation Automatic time synchronization with NTP server

HDD up to 4 HDDs (up to 1 TB each),

Backup DVD/CD disc, USB Flash Memory, HDD disc, through the network

DVD-RW Recorder Built-in

External Ports 1 x Ethernet - RJ-45, 10/100 Mbit/s 3 x USB 2.0 - external memories and mouse, 1 x RS-485 - PTZ cameras and keyboard NV-KBD30,

1 x RS-232– only for service

PTZ Control directly from recorder or through the network (N-Viewer4000, IE)

PTZ Protocols Novus-C, Pelco-D

Device control front panel buttons, network ( N-Viewer4000, Internet Explorer), keyboard NV-KBD30, USB mouse

Menu Multilingual OSD

Software N-Viewer4000

Password Authorization Groups and users profiles with password protection

Auto System Recovery Hardware WATCHDOG Function

Power Supply 100 ~ 240 VAC

Power Consumption approx.70 W without HDD, approx. 100 W with 4 HDDs

Operating Temperature 5°C ~ 40°C

Operative Relative Humidity 0% ~ 80% (without condensation)

Dimensions (mm) 430 (W) x 88 (H) x 450 (D)

Weight 8,1 kg (without HDD)

Rack Mount Enabled, 2U

Main Monitor (1 x BNC, 1 x VGA, 1 x S-Video),

Spot Monitor (4 x BNC)

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

9

2. STARTIG THE DEVICE

2.1. Getting the device ready to work

Please take extra caution when unpacking the device.

Please make sure that the following items are included in the package:

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

WARIG!

It is not allowed to power on the equipment directly after it has been brought from a place with low

temperature. If the device has been brought from an area of lower temperature the user should wait

until the equipment warms up and reaches the room temperature. Caution: Before starting the device

read the input description on the back panel.

NV-DVR4508 or NV-DVR4516 Recorder.

Power Supply Cord CD containing manual

and software

STARTIG THE DEVICE

User’s manual Remote controller

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

10

2.2. Electrical connection and other back panel elements

STARTIG THE DEVICE

1. VIDEO IN/LOOP 8 or 16 video inputs, with looped outputs, to connect cameras.

2. VIDEO OUT output to connect main monitor

3. SPOT 1~4 outputs to connect up to 4 spot monitors. Each spot monitor can display full

screen image from one camera or from cameras in sequence

4. Cooling fan (DO NOT COVER!!!)

5. ARI (Alarm Reset Input): external input signal connected to ARI and GND sockets. The

signal voltage should be above 0,3V longer than 0,5s to deactivate alarm

output.

PANIC external input signal connected to PANIC and GND sockets. The signal

activates or deactivates alarm recording.

6. RS-485 RS-485 connector for PTZ camera control or system keyboards

7. Power supply socket 230V AC. Please make sure that the plug is inserted

correctly and cable is connected to a socket with a grounding pin. It is not

recommended to strongly bend the cable .

7

2

3

1 4

5 6

NV-DVR4516

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

11

8. AUDIO IN 1/4 4 audio inputs (RCA connectors) for microphones.

OTE: Sound recording can only take place when legal regulations

of a given country allows it.

It is strongly recommended to connect microphones to recorder through

amplifiers. Recorder’s audio inputs aren’t equipped with amplifiers.

9. AUDIO OUT audio output for external speaker. Recorder’s audio output is not equipped

with amplifier, so please use speakers with amplifiers.

10. ALARM INPUTS alarm inputs, which can be set from the menu as normally open (N.O.) or

normally closed (N.C.), 16 or 8 according to a model. In order to detect the

signal it has to last at least 0.5 sec. The ground alarm device need to be

connected to one of the GND connectors.

11. ALARM OUTPUTS recorder can activate external devices such as: buzzer, lamp, siren...

12. USB USB socket to connect mouse or external memory.

13. VGA output to connect the main monitor in the VGA mode (computer mode).

You need to use signal cord provided with the monitor.

14. PORT RS-232 only for service

15. NETWORK RJ-45 connector to connect the device to a local network in the 10/100Mbs

standard.

NV-DVR4516

STARTIG THE DEVICE

8

9

10

11 15

14 13

12

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

12

2.3. Connecting External Devices

All installation procedures should be conducted by qualified personnel.

Before device installation and operation please analyze the scheme shown below. Depending on

specific user needs and requirements each system will consist of various number of external devices.

Monitors, cameras and other devices are not included and must be purchased separately. Detailed

devices connection description is included in following chapters of this manual.

STARTIG THE DEVICE

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

13

2.4. Front Panel Description

NV-DVR4516

STARTIG THE DEVICE

NOTE: USB mouse or external system keyboard can be used to control the recorder. Detailed

information about USB mouse control can be found in full user’s manual in chapter 10.

1. ON/OFF BUTTON LED is lightning when supply power is on. After pressing the button

recorder starts. Pressing the button, when recorder is on, logs the

user out and shuts down the recorder.

2. USB PORTS USB ports to connect mouse or external memory for backup records

and firmware upgrade.

3. IR Remote control receiver.

4. POWER, RECORDING AND NETWORK LEDS

Red power LED is lightning when recorder is on.

Red recording LED is lightning when video is recorded.

Green network LED is blinking when recorder is connected to the

Ethernet network.

5. 1~16 (1~8) Displayed channel selection. When you press a button i m a g e

from a camera connected to this channel is displayed. Images are

displayed in full screen mode. Buttons are also used during

inserting password.

1

2

3

4

6

7

8

5

9

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

14

6. BUTTONS By pressing the buttons in playback mode changes playback

direction forward or backward .

In PTZ mode buttons are used to control image sharpness.

7. BUTTON In pla yback mode button pauses the video. Second pressing

starts playback again.

In PTZ mode button is used to save current camera position.

8. BUTTONS In playback mode buttons change playback speed.

Successive pressing one of the buttons increases playback speed

to: x2, x4, x8, x16, x32, x64.

In PTZ mode buttons are used to change focal length.

- Zoom in; -Zoom out.

9. JOG wheel JOG wheel, in playback mode, changes forward or backward display

speed to: x2, x4, x8, x16, x32, x64.

Centre part of the JOG wheel enable playback in image by image

mode.

Front panel buttons are highlighted in green.

All active buttons are highlighted. The number of active buttons depends on DVR operation mode (Live

view, playback, PTZ control).

STARTIG THE DEVICE

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

15

10. BUTTON In live monitoring mode, button changes display

mode.

In PTZ mode, button displayes previous observation position

or pattern.

11. BUTTON In live monitoring mode, button starts sequential d i s p l a y

on the main monitor.

In PTZ mode, button displayes next observation position or

pattern.

12. BUTTON In live monitoring mode, button starts alarm recording

mode.

13. BUTTON In live monitoring mode, button zooms in displayed video.

In PTZ mode, button is used to create observation pattern in

the camera menu.

14. BUTTON In live monitoring mode, button opens archive menu.

In PTZ mode, button starts previously chosen pattern.

STARTIG THE DEVICE

10

11

12

13

14

15

16

17

18

19

20

NV-DVR4516

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

16

15. BUTTON In live monitoring mode, button switches device into

PTZ mode. Successive button pressing switches devices i n t o

PTZ mode with presets, PTZ mode with patterns, PTZ camera

menu.

16. BUTTON In live monitoring mode, button opens search recordings

menu. Details about searching are described in the following

chapter of the manual.

In PTZ mode in PATTERN submenu, button opens

NOVUS CAMA menu.

17. BUTTON Exit button closes opened recorder menu window without

saving changes.

In PTZ or playback mode, button switches recorder into live

monitoring mode.

18. BUTTON button is used to confirm user’s choices.

In PTZ mode, button calls previously selected preset or

pattern.

19. BUTTON button is used to enter recorder menu. It is described in the

following chapters of the manual.

20. BUTTONS These Buttons are used to navigate the menu and to set menu

values. In PTZ mode, the buttons are used to move cameras.

In ZOOM mode, the buttons change observation area.

STARTIG THE DEVICE

▼ ▲ ► ◄

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

17

STARTIG THE DEVICE

2.5. HDD Installation

DVRs NV-DVR4508 i NV-DVR4516 support up to 4 hard disks (after DVD-RW removal)

OTE: It is recommended to use Hitachi and Seagate disks

Maximum single disk capacity is 1TB SATA.

OTE: It is not recommended to use Samsung or Western Digital disks. OVUS

SECURITY Sp. z o.o. does not take any responsibility for problems caused by

using not recommended hard disks

OTE: If disk was previously used in other devices it is necessary to format the diskas all

data on that disk can be erased.

TURIG THE POWER O

Switching power button into O position starts the recorder. System loading may last about

30 seconds. It is strongly recommended not to initialize any function or press any button during

that time. Switching power button into OFF position turns the recorder off.

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

18

3. RECORDER’S MEU

NV-DVR4508 and NV-DVR4516 recorders have multilevel menus displayed on the screen.

The menu is multilingual and it can be displayed in English, German, Spanish, Polish or Russian.

The only difference between 8– and 16-channel versions is the amount of channels. There are 8 or 16

vision channels, alarm inputs etc.

Before using your DVR for the first time, you need to establish the initial settings. This includes items

such as time and date, display language, remote control, network etc.

Press the button to enter the menu. The Login screen appears:

Select user and enter the password by pressing the appropriate combination of channel number buttons

and then the button.

Default login: ADMI and password: 1234 when logging in for the first time.

To navigate the menu using arrow keys.

To confirm choices, enter submenus and edit fields use button .

To change values use arrow keys.

To exit the menu or close submenu window use button .

Sometimes it is necessary to enter the name or a title. When such field is chosen virtual keyboard

appears. To choose a letter use navigation buttons and confirmed your choice by button.

For capital letters use button. button deletes last letter entered.

RECORDER’S MEU

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

19

RECORDER’S OPERATIO

Widok dla NV-DVR1600

4. RECORDER’S OPERATIO

4.1. Live monitoring

As soon as the DVR completes its initialization process, it will show live video on the attached monitor

and will play live audio through attached speakers. The default mode is to display all cameras at once

(16 or 8depending on the DVR model). Press one of the camera buttons to display this camera in full

screen. By pressing button you can change display formats .

Different display formats can be defined by administrator. In one display format single camera can be

displayed only once.

If images from 4 cameras are displayed simultaneously on the monitor, press or the button to

change displayed cameras according to the following scheme.

Press button to start cameras sequence display. Pressing single camera channel or button again

stops sequence display.

Sequence display is set in DISPLAY menu, SEQUENCE submenu.

To start sequence display on SPOT monitors set SPOT-OUT in the DVR DISPLAY menu.

▲ ▼

NV-DVR4508(S)/DVD / NV-DVR4516(S)/DVD 1.1

version - User’s manual short form

20

RECORDER’S OPERATIO

4.2. Playing recorded video

Users whose group has playback right after logging in to search menu are able to play back recorded

images.

Press button to start menu.

After logging in, the search menu appears:

Using navigation keys user can choose search by time or search by event mode.

From search menu user can switch directly to archiving menu.

If search by time mode was chosen, next window appears:

Page is loading ...

Novus NV-DVR4516(S)/DVD User manual

Novus NV-DVR4516(S)/DVD User manual

Related papers

Other documents