QUICK START GUIDE
www.lorexcctv.com
Product Information
User Manuals
Quick Start Guides
Specification Sheets
Software Upgrades
Firmware Upgrades
www.lorexcctv.com
VISIT:
Lorex Technologies Inc.
Copyright © 2008 Lorex Technologies Inc.
As our products are subject to continuous
improvement, Lorex reserves the right to
modify product design, specifications and
prices, without notice and without incurring
any obligation. E&OE
It’s all on the Web!
Camera Specifications
PROFESSIONAL
VARIFOCAL
SURVEILLANCE DOME
CAMERA
Day/Night, Weatherproof, Vandal
Resistant, Advanced Image Sensor
Specfications:
Image Sensor 1/4” AIS
Video Output
Horizontal Resolution
FOV (diagonal)
Termination
Lens / Lens Mount
S/N Ratio
Sync. & Scan. Systems
IR Range
Power Consumption
NTSC: 656 (H) x 492 (V)
480 TVL
30~65 Degrees
Video: BNC Female
4~9 mm F1.6/ Varifocal
> 48dB
Internal; 2:1 Interlace
Up to 82 ft (25 m); 36 LEDs
300mA max
Operating Temp. 14°F ~ 122°F
(-10°C ~ 50°C)
Comp. 1.0 Vpp @ 75ohm
Iris & Shutter Speed AES; 1/60 ~ 1/50,000 sec.
Power Requirement 12V DC ±10%
Dimensions DIA: 4.8” (120 mm)
Minimum Illumination
Video Format / Pixels
0.5 LUX @ F1.2 (IR Off)
0 LUX (IR LEDs ON)
Weight 1.55 lbs /703 g
Dimensions
3.5in/
90mm
English Version 1.0
MODEL: VQ1636HRB
4. Connect the A/C Power Adaptor to the 60ft
Extension cable (Black connector). Plug the
Power adaptor to a wall outlet.
Note: This camera includes a mechanical Auto IR Cut filter. When
conditions change between day/night, an audible clicking noise will be
heard coming from the camera. This clicking is normal, an indicates that
the IR filter is working..
5. Use a screwdriver to adjust the Focus and Zoom
control screws on the camera if necessary.
Figure 4.0 Connect power cable from BNC extension cable to the AC
Power Adaptor (included).
Focus
Zoom
Figure 5.0 Set the focus and zoom with a screwdriver
Contents Installing the camera
1 x Vandal Resistant
Weatherproof Day/Night
Dome Camera with
Varifocal Lens
Features
• 1/4” Advanced Image Sensor (AIS) provides a High
Resolution image (480 TV Lines)
• Auto Mechanical IR Cut Filter removal function ensures
accurate color reproduction
• Weatherproof design: ideal for indoor and outdoor
applications*
• 3-axis design allows for wall or ceiling mounting
• Enhanced Night Vision Capability — up to 82 ft / 25m **
* Not recommended for submersion in water
** IR Illumination range of 82 ft (25 m) under ideal conditions. Objects at or
beyond this range may be partially or completely obscured, depending on the
camera application.
WARNING - A REGULATED UL/CSA APPROVED 12V DC 500mA
power supply is REQUIRED for use with this camera. Use of a non-
regulated, non-conforming power supply can damage this product and
will void the warranty.
4 x Mounting screws
1 x Allen key
Setting up the camera
Setup Diagram
1 x 60ft. BNC/Power
Extension Cable
1 x BNC to RCA
Adaptor
1 x AC Power Adaptor
Prior to installing the camera, make sure of the following:
• Decide to run the cables through the wall/ceiling (drilling required),
or along the wall/ceiling.
• If you run the cables along the wall/ceiling, you must run the cables
through the opening in the camera base, then tuck the cable into
the notch on the base. This will keep the camera base flush to the
wall/ceiling when mounted..
To install the camera:
1. Mount the Camera Base to the ceiling or wall using
the provided screws.
Note: You may need to disassemble the camera using the provided
Allen key. Loosen the tighening screws located on the outer ring of the
Dome Cover.
2. Position the Ball Camera to the desired position
and angle.
3. Position the Dome Cover over the Ball Camera.
Holding the cover firmly in place, use the Allen key
to tighten the screws on the outer ring of the Dome
Cover.
4. Connect the BNC end of the Camera Cable to an
extension cable, or directly to a DVR /
Observation System or to a TV/VCR.
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the cameras and
cables to the TV,VCR, DVR or Observation System.
Figure 1.0 Attach the base to the mounting surface.
Figure 4.0 Tighten the dome cover using the Allen key.
Figure 3.0 Connect the BNC cable to a DVR, CCTV, monitor or TV
/