Hytronik HED6045/D2 User manual

Brand: Hytronik

Model: HED6045/D2

Type: User manual

Hytronik HED6045/D2 is a 45W LED driver with DALI and switch-dim dimming capabilities. Its dimming interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches. This feature makes it suitable for applications where multiple LED drivers are connected to a single switch, allowing for easy and convenient control of multiple lights. The driver has a permanent memory function, which means that the light always starts up at the previous level when it was switched off last time, ensuring consistent and user-friendly operation.

INSTRUCTION MANUAL FOR 45W DALI LED DRIVER

MODEL NO.: HED6045/D2

WIRING DIAGRAM

Wiring Diagram For DALI Wiring Diagram For Switch-Dim

3rd Floor, block C, complex building, 155#, Bai'gang road south,

Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023

Tel:86-752-2772020 F:86-752-2777877

E: [email protected] W:www.hytronik.com

CHINA FACTORY

Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,

Kowloon Bay, Kowloon, Hongkong

T: 00852-35197525 F: 00852-30116936

E: [email protected]

HYTRONIK INDUSTRIAL LIMITED

185

additional cap for stand alone installation

79.2

LED Current Selection

LED−

LED+

DA/P

DA/N

126

4.1

3.9

79.2

129.4

140.6

LED CURRENT SELECTION

The current can be easily configured by choosing the correct

combination of the DIP switches (see table below):

1050mA

1000mA

950mA

900mA

800mA

700mA

600mA

500mA

350mA

1 2 3 4 5

DA/P

DA/N

LED+

LED−

LED+

LED−

DA/P

DA/N

DA/P

DA/N

LED+

LED−

DA/P

DA/N

LED+

LED−

WARNING: Please make sure the correct current is selected before starting the driver!

1. 200 metres (total) max. for 1mm² CSA (Ta = 50)

2. 300 metres (total) max. for 1.5mm² CSA (Ta = 50)

Highlights

• DALI, switch-Dim dimmable• In compliance with DALI 2 standard

•DALI default feedback

Permanent Memory

This driver has built-in permanent memory against power failure, which means the light always starts up at the previous level when it

was switched off last time.

SPECIFICATION

Mains voltage

Mains current

Power factor

Operation temperature

Dimming interface

Abnormal protection

EMC standard

Safety standard

DALI standard

Dielectric strength

IP grade

220 ~240VAC 50/60Hz

≥0.95

Ta: -20~+50 Tc:+80℃℃

Output short-circuit protection, Overload Protection, Open-circuit Protection with auto-reset

EN55015, EN61547, EN61000-3-2/-3-3EN62479

EN61347-1, EN61347-2-13

CE, EMC

IEC62386-101, IEC62386-102, IEC62386-207

Input → output : 3000VAC / 5mA / 1min

IP20

240 ~ 220mA

3.5-19W/350mA /10-54V 5-27W/ 500mA /10-54V 7-38W/ 700mA /10-54V

88%

DALI, Switch-Dim.

Max. output

power/current/voltage

Certification

Max. Efficiency

6-32W/ 600mA /10-54V

8-42W/800mA /10-52V 9-45W/900mA /10-50V 9.5-45W/ 950mA /10-47V

10-45W/ 1000mA /10-45V

10.5-44W/ 1050mA /10-42V

The provided Switch-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.

Up to 64 LED drivers maybe connected to one switch.

Switch Action Response

Short press (<0.4 second) Toggle light on / off

Note: short press has to be longer

than 0.1s, or it will be invalid.

Long press (>0.4 second) Toggle dim light / increase brightness

Switch-Dim

This series of products are supplied as ‘plug n’play DALI’ or ‘independent DALI’ system ready.

These models are also fully DALI addressable and may be assigned to groups within the limits specified by the DALI protocol or supporting DALI

controllers by using a DALI programming tool.

DALI

Switch Action Response

Long press (>15 seconds) All lights will dim down to minimum then return to 50% brightness

* The maximum length of the wires from push to driver should be no more than 20 meters.

Synchronization

Hytronik HED6045/D2 User manual

Hytronik HED6045/D2 User manual

Hytronik HED6045/D2 User manual

Related papers

Other documents