WRIGHT STANDER-I-WSTN User manual

Brand: WRIGHT

Model: STANDER-I-WSTN

Type: User manual

Operator’s Manual

STANDER INTENSITY

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY OR DEATH.

Read this manual and other manuals that came with your mower before operating.

from Wright Manufacturing, Inc. Grass Gobbler, Gobbler, Leaf Gobbler, Velke, Pro 1, X2, Stander, and Sentar are trademarks of Wright Manufacturing.

Serial # 155791 and higher until superseded

Revised 03/01/23

P/N 79510001

Table of Contents

1 INTRODUCTION ........................................................ 1-1

2 NEW MACHINE SETUP ............................................. 2-1

3 SAFETY PRECAUTIONS ........................................... 3-1

Important .................................................................. 3-1

Safety features ......................................................... 3-1

Training .................................................................... 3-1

Preparation .............................................................. 3-2

Operating ................................................................. 3-2

Slope Specic .......................................................... 3-3

Children Specic ...................................................... 3-3

Fire and Fuel Specic .............................................. 3-4

Service ..................................................................... 3-4

4 MACHINE OVERVIEW ................................................ 4-1

Specications ........................................................... 4-1

Engine

Electrical System

Drive System

Hydro Oil System

Fuel System

Speed

General Dimensions

Torque Specications

Safety Interlock System ........................................... 4-1

Machine Features .................................................... 4-2

Overview

Operator Area

Control Panel/ Steering Levers Detail

Warning, Safety, and Instructional Decals ............... 4-3

Pictogram Meanings ................................................ 4-3

5 OPERATION ............................................................... 5-1

Adding Fuel .............................................................. 5-1

Fueling ..................................................................... 5-1

Starting the Machine ................................................ 5-1

Driving the Machine: ................................................ 5-2

Operating the Operator Presence Control (OPC)

Switch ...................................................................... 5-2

How to Stop and Park the Machine ......................... 5-2

Driving the Machine Over a Curb: ............................ 5-3

Mowing on Varying Terrain ....................................... 5-3

Facing Uphill

Facing Downhill

Crossing a Slope Sideways

Discharge Chute ...................................................... 5-3

6 SERVICE AND MAINTENANCE ................................ 6-1

Neutral Adjustment ................................................... 6-1

Tracking Adjustment ................................................. 6-1

Check Machine Tracking

Adjust Machine Tracking

Reaching Maximum Capable Speed

Tire Maintenance and Pressure ............................... 6-1

Troubleshoot No-Start Condition .............................. 6-1

Moving the Mower if it won’t Start ............................ 6-2

Troubleshoot No-PTO Condition .............................. 6-2

Deck Lift Spring Adjustment ..................................... 6-2

Deck Adjustments .................................................... 6-2

Height of Cut ............................................................ 6-2

Cut Setting Recommendations

Troubleshooting Cut Quality ..................................... 6-3

Belt Adjustment/Replacement .................................. 6-3

Replacing the Cutter Deck Belt

Replacing the Drive Belt

Hydraulic System ..................................................... 6-4

Bleeding Air from the Hydraulic System

Check Hydro Oil

Fill Hydro Oil

Lubrication ............................................................... 6-4

Spindle/Drive Pulley R&R ........................................ 6-5

Cutting Blades .......................................................... 6-5

Battery Service ......................................................... 6-5

Parking Brake Adjustment ........................................ 6-5

Loading/Unloading ................................................... 6-5

Transportation .......................................................... 6-6

Cleaning the Underside of the Mower ...................... 6-6

Engine Manual / Maintenance ................................. 6-7

Maintenance Interval Chart ...................................... 6-7

Daily Visual

Every 100hrs

Every 300hrs

Every 500hrs or Annually/Oseason

Maintenance Record ................................................ 6-8

Maintenance Record ................................................ 6-9

7 WRIGHT MANUFACTURING, INC. POWER

EQUIPMENT LIMITED WARRANTY .............................. 7-1

8 FEDERAL EVAPORATIVE EMISSIONS CONTROL

WARRANTY STATEMENT ............................................. 8-1

Thank you for choosing to purchase our equipment. We are focused on giving you advanced engineering and

quality construction in each machine we build. This manual explains the features and promotes safer use of

the machine. Please read it in its entirety and follow the instructions carefully so that you can have many years

of safe and productive operation with your Wright machine.

Your Wright dealer knows your machine and is interested in your satisfaction. Your dealer can provide you with

quality maintenance and other assistance that you may need.

This manual is an important part of your machine and should remain with the machine when you sell it.

The owner’s responsibilities include, but are not limited to, ensuring operators and mechanics read and

understand this manual, adhere to its recommendations and procedures for safe operation, and maintain the

machine for safe operation. The owner must not make assumptions as to the qualication of operators or

permit careless or unqualied operators to have access to this machine. Wright reserves the option to make

changes at any time without notice.

It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any

forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as

dened in Section 4442, maintained in eective working order or the engine is constructed, equipped, and

maintained for the prevention of re.

The Engine Owner’s Manual contains information regarding the US Environmental Protection Agency

(EPA) and the California Emission Control Regulation of emission systems, maintenance, and warranty.

Replacements may be ordered through the engine manufacturer. Unauthorized changes to the engine, fuel or

venting system, may violate EPA and CARB regulations.

Accident prevention regulations, other general safety regulations, occupational safety rules, and trac

regulations must be followed without fail.

CALIFORNIA Proposition 65 Warning

The engine exhaust from this product contains chemicals known to the State

of California to cause cancer, birth defects, or other reproductive harm. Battery

posts, terminals, and related accessories contain lead and lead compounds,

chemicals known to the State of California to cause cancer and reproductive

harm. Wash hands after handling. Use of this product may cause exposure to

chemicals known to the State of California to cause cancer, birth defects, or

other reproductive harm. For more information go to www.P65Warnings.ca.gov.

SAFETY ALERT

This safety-alert symbol is used throughout the manual to identify potential hazards that may cause serious

injury or death. To reduce the potential for injury, comply with these safety instructions, and pay attention to the

safety alert symbol, which means Caution, Warning, or Danger—personal safety instructions. Failure to comply

with the instructions may result in personal injury or death.

1-1

1 INTRODUCTION

2-1

2 NEW MACHINE SETUP

If you are not completely familiar with the Safety Instruction Manual read it now before proceeding with the

Pre-Delivery Service of the mower.

The following items must be completed before attempting to operate a newly delivered machine.

1. Inspect the mower for any damage, missing parts, and labels.

2. Check for any recall or service notices.

3. Check and adjust engine oil.

4. Check and adjust hydraulic uid level.

5. Check and adjust rear tire pressure – 18-22 psi. is recommended. A change in tire pressure may require

the cutter deck to be readjusted.

6. Connect battery cables, red rst, and then black.

7. Check the deck height select for proper operation and range.

8. Add regular unleaded gasoline to fuel tank.

9. Check brake and control interlock.

a. Try starting the engine with the parking brake released. (Engine should not start).

b. With the hand controls in the middle or neutral position, apply the parking brake.

c. Start the engine.

d. Check if the parking brake locking system prevents the machine from being driven while engaged. If

not, service the brake system.

e. Release the parking brake. Move the control levers, one at a time, to make the wheels move in forward

and backward rotation.

10. Test the Clutch/Brake

a. Insure the area is clear of people and objects that may be thrown.

b. Move the engine throttle control to ¾ RPM speed setting.

c. Turn on the blade clutch switch and check for normal operation.

d. Cycle the PTO a few times about 10 seconds apart. If the blades do not start and stop with-in 7

seconds each time, service the blade brake system.

e. With the blades on, disengage the OPC switch to test the Operator Presence Control switch (OPC).

The engine should die and the blades should stop with-in 7 seconds. If not, service the OPC system.

f. Disengage the blades.

11. Drive the mower around an open level area. Check that the mower drives in a reasonably straight line.

12. Listen for any unusual noises and test for irregular operation and adjust or service as necessary.

13. Go over the safety information and operating procedures in this manual with the operator. Instruct each

operator in proper operation and observe during initial operation on a level area. Repeat until the operator

is familiar and comfortable with the basic operation and use of the mower.

Dealer:

you have successfully completed the pre-delivery service checklist. The limited warranty is considered invalid

unless the unit is registered and the above steps are taken.

Remember, the purchaser is both your customer and our customer and his/her satisfaction is very important.

Thank you for supporting our products.

3 SAFETY PRECAUTIONS

3-1

Important

This machine is capable of amputating hands and

feet and throwing objects. Failure to observe the

following safety instructions could result in serious

injury or death.

• This machine is constructed only for o-road

use mowing grass on lawns without obstacles

such as stones, tree stumps, and steep inclines.

• The machine can also be used for other tasks

when equipped with approved attachments, for

example the Grass Gobbler and Velke. Some

accessories may void your warranty.

• Lawn machines and all power equipment can

be dangerous if used improperly or by untrained

operators.

• The owner/user can prevent and is responsible

for accidents, injuries occurring to people, or

damage to property.

• Only operate the machine in daylight or good

articial light. Failure to clearly see the ground

while operating may result in sudden impact,

loss of control, or thrown objects.

• Only operate the engine in well ventilated

areas. Exhaust gases contain carbon

monoxide, a deadly poison.

• Lightning can cause severe injury or death.

If lightning is seen, or thunder is heard in the

area, do not operate the machine.

• Do not operate the machine while tired, ill, or

under the inuence of alcohol or drugs.

• This machine is designed for use by physically

t, experienced, and professional commercial

operators which must be no less than 120

pounds and no more than 325 pounds.

• Do not wear radio or music headphones or use

a digital device. Safe service and operation

require your full attention.

• Always follow OSHA approved operation.

• When machine is left unattended, stored, or

parked, lower the cutter deck until it rests on a

positive mechanical stop.

• Do not carry passengers and keep bystanders

away.

• Do not carry equipment on the machine.

• When loading or unloading use only a full-width

ramp which is wider than the machine, provides

good traction, and is not positioned with a steep

angle. Use caution when loading or unloading.

• When hauling, tie the machine down with

appropriately rated straps or chains.

• Never leave or park the machine unattended on

sloped ground or incline.

• Use only approved repair parts to maintain.

• Unauthorized modications to the machine may

impair its function and safety.

Safety features

The machine is designed with your safety in mind.

It has the following safety systems with which you

should become familiar:

• The warning decals on the machine including

the instrument panel and cutter deck.

• The brake must be engaged and the PTO/blade

switch “o” prior to starting the engine.

• The OPC switch must be actuated in order to

engage the blades.

• Disengaging the Operator Presence Control

(OPC) switch while the blades are running will

cause the engine and blades to stop with-in 7

seconds.

• Spring loaded chute deector helps reduce

trajectory of thrown objects.

• Belt, pulley, fan, and heat covers on to reduce

access to moving and hot parts.

• Anti-tip rollers provided at the rear of the

machine reduce the risk of machine tipping.

• DO NOT disable any of the safety features.

• Unauthorized modications to the design of

the machine will absolve the manufacturer

from liability for any resulting personal injury or

property damage.

Training

• Read the operators manual, warnings, labels,

attachments manual, engine manual, and other

training material carefully. If the operator or

mechanic cannot read the language provided,

it is the owner’s responsibility to explain this

material to them.

• Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

• All operators and mechanics should be trained.

The owner is responsible for training the users.

• Never let children or untrained people operate

or service the equipment. Local regulations may

restrict the age of the operator.

• The owner/user can prevent and is responsible

for accidents or injuries occurring to himself or

herself, other people, or damage to property.

• Only allow operators, who are responsible,

trained, familiar with the instructions, and

physically capable to operate the machine.

3-2

Preparation

• Carefully inspect and walk the property where

you plan to use the machine for hidden, hard-

to-see objects or uneven ground that may

be hidden in the grass. Uneven terrain could

overturn the machine, or cause the operator to

lose balance or footing.

• Clear the work area of moveable objects,

including but not limited to, rocks, glass,

toys, wires, dog chains/cables, and golf balls

that might be picked up by the machine and

dangerously thrown.

• Remove or mark the location of all immovable

objects or irregular areas and be sure not to hit

them with any part of the machine. Obstacles

including and not limited to holes, abrupt

changes in ground contour, tree trunks, stumps

or roots, pipes or posts, paving edges, and

rock outcroppings can abruptly turn or stop the

machine. This could throw you o the machine

or possibly over the handle bars causing

serious injury or death.

• Check carefully for overhead obstacles (i.e.

branches, clothes lines, doorways, electrical

wire, decks, building overhangs, etc.) before

operating and do not operate near them.

• Wear appropriate clothing and personal

protective equipment; including safety glasses,

long pants, substantial slip-resistant footwear,

gloves, and hearing protection. Tie back long

hair.

• Do not wear jewelry, sneakers, sandals, shorts,

baggy clothing, or any clothing or accessories

with loose loops or lanyards.

• Keep the area of operation clear of all

bystanders, particularly small children. Stop the

machine and attachment(s) if anyone enters the

area.

• Check that the operator’s presence controls,

safety switches, interlocks, hardware, and

shields are attached and functioning properly.

Do not operate the machine unless they

are functioning properly. Repair or replace

damaged, badly worn, or missing parts

• Do not operate machine without the entire

grass catcher, discharge chute, or other

safety devices in place and functioning

properly. Check frequently for signs of wear or

deterioration and replace as needed.

• Ensure that all drives are in neutral and that

the parking brake is engaged before starting

engine. Start the electric start engines only from

the operator’s position.

• Before using, always visually inspect to see

that the blades, blade bolts and the mower

assembly are not worn or damaged. Never

straighten or weld blades.

Operating

• Keep a rm hold of the stationary handle at

all times. Keep both feet on the platform at all

times.

• To prevent serious injury never place your foot

or feet on the ground near the back edge of the

machine while backing up.

• Do not suddenly push controls in forward

direction while machine is in a rearward motion.

Operate the controls smoothly.

• Do not mow in reverse unless absolutely

necessary. Always look down and behind before

and while backing to ensure a clear path. Use

extra caution when operating in reverse.

• Do not operate the machine faster than

conditions allow. For example, hills, wet or

bumpy ground, dim light or high grass are all

conditions requiring slower speeds. Never

operate the machine at the highest speed

unless you are on level, wide, open areas

of clearly visible ground or transporting on

paved areas. Speeding with any machine is

dangerous, and so is traveling faster than

conditions should permit on this machine.

Sudden stops from excessive speed or falling

o the machine may cause serious injury or

death.

• Know the controls and how to stop quickly.

• During zero-radius turns (when one machine

wheel rotates backwards while the other

rotates forward) drive extra slowly to reduce the

possibility of losing traction, losing control, or

losing your balance. This will help prevent you

from being thrown o the machine.

• Use care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

• Slow down and use caution when making turns

and crossing roads and sidewalks. Stop the

blades if you are not mowing. Watch for trac

when operating near or crossing roadways.

• Turn o blades and wait for them to stop before

crossing roadways, gravel areas, and climbing

or dismounting curbs.

• Do not raise the mower deck with the blades

running.

• Do not direct discharge material toward anyone.

Avoid discharging material against a wall or

3-3

obstruction. Material may ricochet back toward

the operator.

• If the machine discharge clogs, turn o the

blade clutch switch, apply the parking brake,

stop the engine and remove the key before

removing obstruction(s).

• Do not leave the machine running unattended.

Always park on level ground, disengage the

attachment, set parking brake, and stop engine.

• Stop on level ground, disengage drives,

engage the parking brake, and shut o the

engine before leaving the operator’s position

for any reason including emptying the catchers,

unclogging the chute, and servicing the blades

or cutter deck.

• Stop equipment and inspect the blades after

striking objects or if an abnormal vibration

occurs. Make the necessary repairs before

resuming operations.

• Keep hands, feet and clothing away from

rotating parts, especially the rear wheels,

blades, engine ywheel, fans, belts and pulleys.

• Do not touch parts that may be hot from

operation. Allow the machine to cool before

attempting to maintain, adjust, service, unjamb,

or service the machine.

• Do not put hands or feet near rotating parts or

under the machine. Keep clear of the discharge

opening at all times.

Slope Specic

• Before operating on slopes, walk the area

and evaluate the surface for traction and

smoothness. Slopes with drop os, water, or

compromised traction should be maintained

through other maintenance techniques.

• Slow down and use extra care on hillsides. Be

sure to travel in the recommended direction on

hillsides. Turf conditions can aect the stability

of the machine.

• Do not operate near drop-os, ditches,

embankments, or water. The machine could

suddenly roll over if a wheel goes over the

edge or the edge caves in. The machine could

suddenly slide if traction is compromised. Leave

a safety area between the machine and any

hazard.

• Slow down and use caution when making turns

and when changing directions on slopes.

• Slopes are a major factor related to accidents.

Operation on all slopes requires extra caution.

• Establish your own special operating

procedures and rules for operating on slopes.

These procedures must include a survey of

all mowing sites to determine which slopes

are acceptable. Always use caution, and good

judgement when performing this survey.

• Note that high traction conditions present a

greater rollover hazard while lower traction

conditions present a greater loss of control

hazard. Ground and turf conditions vary

depending on the weather and must be taken

into consideration at all times.

• Some liquid landscape chemicals contain

surfactants which may by very slippery and

severely compromise safe operation.

• Do not operate on steep slopes.

• Do not operate the machine on slopes when the

grass is wet.

• Do not operate machine under any condition

where traction, steering, or stability is in

question. Tires could slide even if the wheels

are stopped.

• Always keep the machine in gear when going

down slopes. Do not coast downhill.

• Avoid starting and stopping on slopes. Avoid

making sudden changes in speed or direction.

Make turns slowly and gradually.

• Use extra care while operating machine with a

grass catcher or other attachment(s). They can

aect the stability of the machine.

• There is a danger of suddenly sliding sideways

or down the hill. When operating on a slope,

travel across the grade whenever possible, not

in an up or down pattern.

• Reduce speed and exercise extreme caution

on slopes and in sharp turns to prevent tipping

or loss of control. Be especially cautious when

changing direction on slopes.

• Do not operate tires that are worn beyond 3/32”

of tread. Do not use unapproved treads or tire

pressures. Unapproved treads or excessive

pressures can compromise your traction.

Children Specic

• Death or serious injury can occur when young

children associate having fun with lawn mowing

equipment.

• Children who have been entertained with power

equipment in the past may be attracted to

the machine while operating. Children do not

understand the hazards of rotating blades and

moving equipment. Never use the machine as a

recreational vehicle or to entertain children.

• Never allow children or untrained operators to

operate the machine. Instruct all operators to

not give children rides.

3-4

• Tragic accidents can occur if the operator is not

alert to the presence of children. Children are

often attracted to the machine and the mowing

activity.

• Never assume that children will remain where

you last saw them.

• Keep children out of the operating area and

under the watchful care of a responsible adult

other than the operator.

• Do not carry children, even with the blade(s)

shut o. Children could fall o and be seriously

injured or interfere with safe machine operation.

Children who have been given rides in the past

could suddenly appear in the mowing area for

another ride and be run over or backed over by

the machine.

• Do not allow children to play on or around

machine when not in use and never leave the

key in the ignition switch. Children may be

injured by hot components and are prone to

attempt operating all functions of the equipment

which may result in becoming pinched, crushed,

or unintended operation.

Fire and Fuel Specic

• Besides routine maintenance, one of the best

ways to reduce the risk of re is to regularly

check and remove debris and combustible

residue from the machine.

• Use extra care when handling fuels. They are

ammable and vapors are explosive.

• Use only an approved container.

• Do not remove the fuel cap or add fuel with the

engine running. Allow the engine to cool before

refueling.

• Keep the machine and engine free of grass,

leaves, excessive grease, oil, or other debris at

all times to reduce the risk of re.

• Do not use the machine to push combustible

materials, such as leaves, branches, or tall

grass.

• Never smoke when handling fuel, and stay

away from open ame or where fuel fumes may

be ignited by spark.

• Never start the engine in an enclosed space

with the presence of fuel vapor. Starting the

engine may ignite fuel vapors.

• Do not smoke near the machine when the

engine is running.

• Do not refuel indoors or in enclosed spaces.

• Never overll the fuel tank.

• Remove machine from truck or trailer before

fueling.

• Do not store the machine or fuel container, or

refuel, where there is an open ame, spark, or

pilot light such as on a water heater or other

appliance.

• If fuel is spilled, do not attempt to start the

engine and avoid creating any source of ignition

until fuel vapors have dissipated.

• Allow machine to cool before storing or

covering. Machine res and structural res can

occur if a machine is stored before allowing it to

cool.

• Always shut o fuel when storing or

transporting.

• Check fuel lines, tank, cap and ttings

frequently for cracks or leaks. Replace

immediately if necessary.

Service

• Only qualied and trained persons who

understand the warnings in this manual should

service this machine.

• Examine the moving parts prior to each use.

Look for excessive wear, deterioration, bald or

worn tires, cracks in parts, lose or missing bolts,

pins, and replace before operating the machine.

Inspect fuel system for leaks or cracks in hoses,

tank(s), and seals.

• Make sure all safety equipment provided

with the machine is in good operating order,

including all the warning decals and the

required operator-presence device which stops

the engine and blades when the switch is

released.

• Inspect the two anti-tip rollers and their

respective bolts at the rear of the machine for

tightness and proper operation.

• Be sure that all parts of the hand-operated

control system are tight and secure. This is to

reduce the possibility that the machine could

have a loss of control.

• Ensure all safety related switches are

operational. Do not disable safety switches.

• Use caution when servicing blades. Wrap the

blade(s) or wear gloves. Replace damaged

blades. Do not repair or alter blade(s). Do

not use blades that have been improperly

sharpened or beyond the serviceable limits. Do

not use blades from unveried sources as the

material may not be suitable.

• Machines with hydraulic pumps, hoses, or

motors: WARNING: Fluid escaping under

pressure may have sucient force to penetrate

skin and cause serious injury. If uid is injected

into the skin, seek immediate medical attention.

3-5

Keep body and hands away from pin holes or

nozzles that eject uid under high pressure. If

a leak occurs, have the machine immediately

serviced by a trained technician. Never use

hands to search for hydraulic leaks. Use

paper, cardboard, or UV dye. Keep body and

hands away from pin holes or ttings that eject

hydraulic uid under high pressure.

• Disconnect spark plug wire(s) and the negative

battery cable before making any repairs.

• The machine should not be used after the

blades or other part of the machine strikes

a foreign object, until conducting a thorough

inspection and any damage is repaired.

• Do not climb underneath

• Do not service the machine while suspended

by an unapproved lift, such as a forklift, or hoist/

structure not approved for overhead lifting.

Use proper lifts, or jack stands to support the

machine.

• Don’t change RPM’s outside of operating limits

or alter the governor operation

• Do not tow or push with force or over long

distances. When moving stuck or disabled

equipment, place transmission(s) in neutral or

hydro bypass.

• Use tires with the original tread pattern. Use

of alternate tires and treads may cause loss of

control.

• Use of parts other than specied parts

supplied by Wright Manufacturing, Inc. may

compromise the safe use of the machine and

not recommended. Their use could void the

warranty. Always check with your Dealer or the

Wright website, www.wrightmfg.com for the Part

Lists and diagrams for your machine.

• Waste products, such as used oil, fuel,

coolant, brake uid and batteries, can harm the

environment and people. Do not use beverage

or unlabeled containers for waste uids –

someone may drink from them. Do not leave

open containers where they can be accessed

by children or animals.

4-1

4 MACHINE OVERVIEW

Specications

Engine

• See your engine owner’s manual for full details

• Full speed 3600 +/- 50 RPM

• No load/Idle: 1550 RPM

Electrical System

• Charging System: Internal stator coil

• Battery Type: Maintenance free

• Battery Voltage: 12 Volts

• Fuses: Two, 20 amp blade type

Drive System

• Pumps: Hydro Gear 10 cc

• Wheel Motors: Danfoss 12 cu in

Hydro Oil System

• Hydro Oil: Wright Blend Full Synthetic 15W-50

Wright PN 36490013

• Hydro Filter: Spin-on, 25 micron, no bypass

Wright PN 34490002

• Tank Fill Level: Until uid is visible in sight glass

• Capacity: approx 3 qts (2.8L)

Fuel System

• Capacity: 5.5 Gal. (20.8 L).

• Fuel Type: Unleaded regular gasoline, minimum

85 octane. Do not use gasoline containing more

than 10% ethanol. Do not mix oil with gasoline.

• Fuel Filter: In line.

• Fuel shut o: On/O located on fuel tank.

Speed

• Forward: 8 mph

• Reverse: 3 mph

General Dimensions

36” 42” 48” 52”

Width, Chute down 49.5” 55” 62” 66”

Width, Chute up 36.5” 42.5” 49” 53”

Length 62” 70” 59.75” 59.75”

Weight 717 lbs 740 lbs 805 lbs 816 lbs

Torque Specications

Critical Application Thread Locker Torque (ft-lbs)

Wheel motor bolts Loctite 2760 33

Clutch to engine shaft Loctite 2760 50-55

Wheel hub to wheel motor N/A 138-158

Wheel lug nuts N/A 80-90

Split Hub (Spindle & Drive) N/A 13-17

Blade Bolts N/A 70-80

Engine Mounting Bolts Greased 35

Caster Wheel Bolt N/A 38

Caster Yoke Pivot N/A 38

Pump Pulley N/A 14

Pump Bypass Valve N/A 42 in.-lbs.

Safety Interlock System

The machine is equipped with a start interlock system. The PTO must be disengaged; brake applied and

control levers in the neutral position in order to start the machine. With the brake applied, the controls are

locked in the neutral position.

If the safety-interlock switches are disconnected or damaged, the machine could operate

unexpectedly, causing personal injury. Do not tamper with the interlock switches. Check the

operation of the interlock switches daily and replace any damaged switches before operating the

machine

4-24-2

Machine Features

• This machine is meant to solely cut, bag or mulch grass.

• The use for any other purpose is not recommended.

• Do not disconnect any safety switches or remove any decals.

Overview

1. Flexible Chute Deector

2. Rear Drive Tire

3. Fuel Tank w/ Vented Cap

4. Battery Box

5. Anti-Scalp Roller

6. Front Caster Tire

7. Cutter Deck

8. Engine

9. Muer/Heat Shield

Operator Area

1. Anti-Tip Wheels

2. Deck Lift Handle

3. Brake Handle

4. Thigh Cushion

5. Foot Platform

Control Panel/ Steering Levers Detail

1. L/R Reverse Control

2. L/R Forward Control

3. Stationary Handle Bar

4. Throttle

5. Choke

6. Digital Hour Meter

7. PTO Switch

8. Ignition Switch

4-3

Warning, Safety, and Instructional Decals

• Specic safety warning decals are located on the equipment near immediate areas of potential hazards.

• Keep all safety signs legible - Replace worn, damaged or missing safety decals.

• Remove all grease, dirt and debris from safety signs and instructional decals.

• If an attachment or accessory has been installed, make sure current safety decals are visible

Pictogram Meanings

Warning: Let the machine

cool down prior to fueling

Warning: Inspect work area for objects that can be

thrown or impacted

Warning: Hot surface.

Stay away.

Warning: Keep the cutter deck opening covered or

the chute down while operating

Engage hand brake Warning: Entanglement hazard

Engine speed control.

Pull switch to engage

blades/PTO. Push switch

to disengage blades/PTO.

Warning: Keep debris o machine at all times

Warning: Stop the blades,

place the controls in

neutral and engage the

brake before dismounting

machine

Warning: Read the Operator’s Manual. Do not

operate this machine unless you are trained.

Warning: Before servicing stop the engine, remove

the key, and read the Operator’s Manual

Ignition: o, on, engage

brake to start

Warning: Stay away from people and children.

Do not operate the machine when children and/or

others are around.

Warning: Use eye and hearing protection

Warning: Keep hands and

feet away from moving

parts

Warning: Thrown object hazard

Warning: Keep shield and

guards in place

Warning: Identies potential hazards that may

cause serious injury or death if you do not follow

the recommended precautions.

Warning: Do not operate

near drop os or water

Warning: Before servicing stop the engine, remove

the key, and read the Operator’s Manual

Warning: Fire hazard Warning: Operate slowly on any incline

Warning: Thrown object

hazard

Warning: This safety-alert symbol is used to

identify potential hazards that may cause serious

cutting or severing hands and feet

5 OPERATION

5-1

Basic Operation: The following procedures are

to guide you through the basic operation of the

machine. You should be a qualied machine operator

according to the safety section of this manual. You

should go through each step, in the order indicated,

every time you start the machine.

This machine produces sound levels in

excess of 85dBA at the operator’s ear and can

cause hearing loss from extended periods

of exposure. Wear hearing protection when

operating this machine.

Adding Fuel

• In certain conditions, fuel is extremely

ammable and highly explosive. A re or

explosion from fuel can burn you and others

and can damage property.

• Fill the fuel tank outdoors, in an open area,

when the engine is cold. Wipe up any fuel that

spills.

• Never ll the fuel tank inside an enclosed trailer.

• Do not ll the fuel tank completely full.

• Add fuel to the fuel tank only to the bottom

of the ller neck. This empty space provided

allows fuel to expand.

• Never smoke when handling fuel, and stay

away from an open ame or where fuel fumes

may be ignited by a spark.

• Store fuel in an approved container and keep it

out of the reach of children.

• Do not operate without entire exhaust system in

place and in proper working condition.

• Never start the engine in an enclosed space

with the presence of fuel vapor. Starting the

engine may ignite fuel vapors.

In certain conditions during fueling, static

electricity can be released causing a spark,

which can ignite the fuel vapors. A re or

explosion from fuel can burn you and others

and can damage property.

• Always place fuel containers on the ground

away from your vehicle before lling.

• Do not ll fuel containers inside a vehicle or on

a truck or trailer bed because interior carpets

or plastic truck bed liners may insulate the

container and slow the loss of any static charge.

• When practical, remove gas-powered

equipment from the truck or trailer and refuel

the equipment with its wheels on the ground. If

this is not possible, then refuel such equipment

on a truck or trailer from a portable container

rather than from a fuel-dispenser nozzle.

• If you must use a fuel-dispenser nozzle, keep

the nozzle in contact with the rim of the fuel

tank or container opening at all times until

fueling is complete.

• Long-term exposure to vapors can cause

serious injury and illness.

• Avoid prolonged breathing of vapors.

• Keep your face away from the nozzle and fuel

tank or conditioner bottle opening.

• Avoid contact with skin; wash o spills with

soap and water.

• Never siphon by mouth

Fuel is harmful or fatal if swallowed.

Use only clean fresh fuel rated 87 octane or higher.

Do not use fuel with more than 10% ethanol, such

as E15, E20, or E85. Do not use fuel containing

methanol, which is harmful to human health. Do not

store untreated fuel in the machine when not used for

more than 30 days.

Fueling

1. Park the machine on level ground in an open

area, engage the parking brake, and remove

the key.

2. Allow the machine to cool down before fueling.

3. Fill the tank to the bottom of the ller tube.

Do not over ll to allow space for the fuel to

expand.

4. Securely install the fuel cap.

5. Check for any leaking or spilled fuel prior to

starting the engine.

Starting the Machine

Note: All engines consume oil. Before using, check

the engine oil.

1. Before starting the engine, make sure the

control levers are in the neutral position.

2. Apply the parking brake if it is not already set.

5-2

3. Turn OFF the blade switch if it is on.

4. Turn fuel valve to the “ON” position.

5. Start the engine according to the engine

manufacturer’s recommendation, see engine

manual. Set the throttle control lever near mid

throttle, pull out on the choke control knob

(carbureted models) and turn the key to the

start position.

• Do not engage the starter for more than ten

(10) seconds at a time. This may overheat

the starter and the wiring systems. Wait ten

(10) seconds between attempts. If the engine

does not start after several attempts or stalls

frequently, take the machine in for service.

• After starting the engine according to the engine

manufacturer’s recommendation, push in on the

choke control knob to open the choke valve.

Driving the Machine:

1. While standing, both feet should be rmly

placed on the foot platform. Set the engine

speed about 1/4 of the way from idle.

2. Release the parking brake.

3. Move the hand control levers, one at a time,

very slightly, forward and backward. Check to

see if the wheels move forward and backward

according to the position of the levers. If not,

check to see that the pump release valves are

closed.

4. With both feet still rmly placed on the foot

platform, increase the engine speed to about

1/2 from idle speed. The higher engine speed

will make the controls much more responsive

and the machine much quicker.

5. New operators should continue to practice

driving the machine in an open area, with the

blades o, at a partial engine speed.

6. Unusual noises or irregular operation: As you

drive the machine, listen for any unusual noises

and test for irregular operation and adjust or

service as necessary.

Operating the Blade Switch (PTO)

Rotating blades may cause severe injury. Before

engaging the cutter blades or PTO, make sure

that the area is clear of bystanders, especially

children.

1. Stand on the operator platform to engage the

Operator Presence Control (OPC).

2. With the engine running, set the engine speed

to approximately ¼ to ½” position.

3. Pull the PTO switch up to engage the cutter

blades.

4. Increase the engine speed to the fast position

for mowing.

Note: Engaging and disengaging the PTO at full

engine speed will not immediately harm the machine,

however the life of the clutch will be much longer if

the engine speed is reduced before engaging the

PTO and again reduced before disengaging the PTO.

This is especially true on larger width machines with

more powerful EFI engines and mulch blades.

Operating the Operator Presence Control (OPC)

Switch

1. With the parking brake applied and blades ON,

try lifting your feet o the foot platform to test

the Operator Presence Control switch (OPC).

2. The engine should kill and the blades should

stop within 7 seconds. If not, service the OPC

system or contact your local Wright dealer. The

OPC switch is located directly above the right

side of the platform and the start/brake switch is

located under the instrument panel.

How to Stop and Park the Machine

1. Come to a complete stop.

2. If the blades are on, turn them o using the

switch on the instrument panel.

3. Make sure the control levers are in the neutral

position.

4. Set the parking brake by pulling up on the brake

handle.

5. Reduce the engine speed to idle.

6. Shut o ignition switch to stop the engine and

then remove the key from the ignition switch.

7. The machine is now parked.

8. Do not leave machine unattended on a sloped

surface.

Children or bystanders may be injured if they

move or attempt to operate the machine while

it is unattended. Always remove the key and

engage the parking brake when leaving the

machine unattended.

5-3

Driving the Machine Over a Curb:

It is recommended to use ramps for curbs 5” and

higher. Using ramps, you can easily back on and o

without damaging your machine or the curb.

1. Raise the cutter deck into the highest position.

2. Drive the machine in reverse at a 45 degree

angle to the curb until you are within an inch or

two of the left-rear tire hitting the curb.

3. Stop and then gradually bump into the curb with

that tire until it is just on top of the curb.

4. If the tire slips then the curb is too high and you

should use ramps.

5. While maintaining the same angle to the curb,

continue to back up until the other rear tire

climbs the curb.

6. After both drive wheels are on top of the curb,

back up so the caster wheels comes over last.

• The technique works the best if you try not to

drive backwards at a near 90 degree angle to

the curb.

• To drive o a curb, reverse the procedure.

• Do NOT step o the machine during ANY

maneuver.

Note: Never drive straight onto or o a curb or climb

or “pop a wheelie” to climb a curb. Abruptly mounting

and dismounting a curb increases the fatigue of the

frame, transmissions, and caster wheels.

Mowing on Varying Terrain

Operating the machine on or near slopes

increases the hazard of rollover and loss of

control and may cause severe injury or death.

Refer to the SAFETY PRECAUTIONS section of

the manual and follow the recommendations

provided.

Facing Uphill

• Lean as far forward as possible to add your

weight to the front of the machine.

• Accelerate gently. Do not accelerate quickly

to avoid allowing the front wheels to lift o the

ground.

• If backing down the hill, do not stop suddenly

but slow down gradually.

Facing Downhill

• Machine has the least weight on the rear drive

wheels and therefore the least traction at the

tires. This is the angle that the machine has the

most tendency to slide.

• However, this is the angle that it has the least

tendency to tip back.

• Lean back with arms stretched out straight

while holding onto the stationary handlebar.

This transfers more of your body weight to the

rear drive wheels for more traction.

• Do not change speed suddenly to minimize the

tendency to slide.

Crossing a Slope Sideways

• Machine has the average amount of weight on

the drive wheels versus the front wheels.

• This angle leaves the least weight on the higher

side drive wheel, increasing the tendency to

slip.

• However this is the preferred angle for mowing

large areas of gentle slopes.

• Lean back and angle yourself to the higher side.

This adds weight to the rear drive wheels and

will provide greater traction.

Discharge Chute

Without the discharge chute, discharge cover,

or complete grass catcher assembly mounted

in place, you and others are exposed to blade

contact and thrown debris. Contact with

rotating mower blade(s) and thrown debris

cause injury or death.

• Do not remove the chute deector from the

mower or permanently secure it in the transport

position in a manner that overrides the closing

spring.

• If the grass deector is ever damaged, replace

it immediately.

• Never put hands, feet, or head under the

mower.

• Never try to clear the discharge area or mower

blades unless the Blade Switch (PTO) is o and

the ignition key is removed.

6 SERVICE AND MAINTENANCE

6-1

Neutral Adjustment

Neutral refers to the machine movement when the

engine is set to full throttle, parking brake is o, and

the control levers are in the neutral position.

The machine should not move forward or backward

in this state. If it does, the neutral setting must be

adjusted by using the Return-to-Neutral (RTN) device

built into the linkage of the hydraulic pump.

1. Lift the rear drive wheels o the ground using a

jack and stands.

2. Loosen the ¼” Allen bolt (A)

3. Rotate the RTN device on the pump for the

wheel that needs adjustment. Stop when the

neutral position is found.

4. Retighten the ¼” Allen bolt. Do not over tighten.

Tracking Adjustment

• Do not adjust the stationary control rods.

• Do not adjust rods such that the pump control

lever (on the side of the pump) hits the internal

pump stop while at full speed.

• This puts direct pressure on the pump stop and

can damage the hydro pump.

• It can be identied by feeling resistance in the

hand controls at the full speed position.

Check Machine Tracking

1. Ensure rear tire pressure is equal on both sides.

2. Drive at full throttle in a level parking lot.

3. Check if the machine drives straight when both

control levers are in the full speed position. If it

does not, tracking adjustment is needed

Adjust Machine Tracking

1. Ensure the machine is parked and the engine is

o.

2. Loosen the jam nut on the rods connected

directly to the hydro pumps.

3. Adjust the rods.

• Turning CCW lengthens the rod and decreases

speed

• Turning CW shortens the rod and increases

speed

• If the machine tracks to the right: lengthen the

left rod or shorten the right rod.

• If the machine tracks to the left: lengthen the

right rod or shorten the left rod.

Reaching Maximum Capable Speed

1. Shorten the rods one turn at a time until you

feel, in the hand control, the pump control lever

contacting the internal pump stop.

2. Lengthen the rods one full turn each.

Tire Maintenance and Pressure

• Excessively worn tire tread is dangerous on all

hills. Replace drive tires with less than 3/32” of

any tread groove left.

• Use tires with the tread pattern recommended

by Wright Mfg., Inc. only.

• Keep the drive tire pressure between 18-22 psi.

• Higher pressures cause the tires to have less

traction, decreasing safety, speed and ride

quality

• Front Casters are equipped with non-pneumatic

tires and do not require any air. They do not

have any tread but should be replaced when

excessively worn.

Troubleshoot No-Start Condition

1. Check that the battery is fully charged. If the

battery repeatedly dies, check the regulator

and charge wire going from the regulator to the

starter battery stud.

2. Check that the fuel valve is fully open.

3. If the battery is good and the starter does not

engage

a. Check that the park brake is engaged and the

PTO switch is o.

b. Check the fuse on the wiring harness.

c. Check the battery (+) and (-) wires to the

engine.

d. Check the harness ground wire at the engine.

e. Check the harness power connection (red)

where the battery cable is connected to the

engine/solenoid

f. Check the connections of the (green) start

wire at the key switch, PTO interrupt switch,

brake interlock switch, and starter.

6-2

g. The starter may have failed. Check your

engine manual.

Moving the Mower if it won’t Start

• Rotate both of the hydro bypass valve levers

about 2 turns CCW.

• DO NOT over tighten these levers.

• Damage may occur to the pump if this valve is

over tightened.

Troubleshoot No-PTO Condition

4. Engine runs but PTO won’t engage.

5. Shut down machine, remove key, allow to cool,

and checking the belt and wiring going to the

clutch.

6. While the engine is o, disconnect the clutch

wire, turn on the blade switch and check for

battery power from the harness. The Blue wire

that goes to the red clutch wire is power from

the PTO switch. The black/orange strip wire

going to the black clutch wire is the ground wire

going to the relay, switch by the platform switch.

a. If no voltage, check relay, Operator Presence

Switch, and PTO switch

b. If battery voltage is coming from the harness,

check the clutch.

7. To check the clutch

a. Visually check the gap between clutch and

the armature. If the gap is excessive the

clutch is mechanically worn out of spec and

must be replaced. A worn clutch may work

when cold and not reengage once warm

and the magnetic coil increases electrical

resistance.

b. Use an ohm meter and measure the

resistance in the clutch. It should be

approximately 1.84 ohms. If the number is

much lower the coil has likely shorted out. If

the number is much higher (or innite) there is

likely a burnt or “open” coil.

Deck Lift Spring Adjustment

The Intensity is equipped with two deck-lift assist

springs.Deck lift spring tension is adjusted at the

factory. If the eort needed to raise and lower the

mower deck is not satisfactory, an adjustment to the

right side spring may be necessary. The left side

spring behind the thigh pad is non-adjustable.

To adjust tension in the right deck spring, tighten or

loosen the eye-bolt Nylock jam nut located in the

front tank bracket. If tightening for more lift assist,

make sure not to over tighten as the mower deck

may oat too freely and “hop” over rough terrain.

Deck Adjustments

The mower deck can be adjusted for pitch and side-

to-side leveling. Pitch is the relationship between the

front of the deck and the rear of the deck in regards

to height of cut. In most cases, a positive pitch (front

of the deck lower than the rear of the deck) of ¼” is

the optimum setting.

These adjustments can easily be made by moving

any or all of the four deck lift brackets up and down

using a ½” ratchet & short extension. It is best to use

blocks to lower the deck onto to assist in the deck

adjustments.

1. Park mower safely on a level surface and inate

tires to the correct pressure.

2. Set deck pin and lower deck to 3” height of

cut. (If using blocks place under deck prior to

lowering)

3. Align blades front to rear, measure front and

rear blade tips to grounds. The front blade

tip should be 3” and rear should be between

3 1/8” – 3 1/4”.

4. Using an 11/16” wrench, loosen the deck lift

bracket nuts. Using the ½ ratchet & extension,

raise or lower the deck lift arm accordingly.

5. Tighten to 45 ft. lbs. After all adjustments are

made, verify measurements

Height of Cut

1. Before adjusting the height-of-cut be sure the

machine engine is o, both rear tires have

proper air pressure, the parking brake is

applied, and the machine is on a at surface.

2. Set the deck lift pin to 3”.

3. Lower the deck lift handle and release the

button. Lift gently on the handle to allow the

button to pop into position.

6-3

Cut Setting Recommendations

Correct cut height is critical to healthy turf. Cutting o

more than 1/3rd of the blade stresses the turf.

In general, the turf will be healthy when cut longer.

When cut taller, the turf develops deeper roots, is

more drought resistant, more disease resistant, and

suppresses weeds.

Cut quality is improved when cut heights are

maintained according to the best practice for the

dominant grass species in the lawn.

Clean under the deck regularly. Grass build up will

cause the airow to be interrupted and result in poor

cut quality. Blades that are worn and have rounded

tips will not cut well.

Troubleshooting Cut Quality

Problem Description Possible Cause Solution

Streaking When strips of uncut

grass are left behind

Blades not sharp Sharpen blades

Blades worn down too far Replace blades

Engine RPM too low Mow at full throttle

Ground Speed too fast Slow down

Deck clogged with grass Clean deck

Stepped

Cutting

Sharp ridges left in the

lawn surface

Deck not leveled correctly Level the deck

Tires not properly installed/inated Check and inate tires

Blades are damaged Replace blades

Deck shell is damaged Repair or replace deck

Spindle is bent or loose Repair or replace spindle

Blades are installed incorrectly Reinstall the blades correctly

Scalping

Brown areas when deck

is close to/hitting the

ground

Lawn is uneven or bumpy Roll or level the lawn

Cut height is too low Raise cutting height

Deck is not leveled correctly Level the deck

Tire pressure is uneven Check and inate tires

Stringers Sparse patches of uncut

grass left behind mower

Blades are dull or nicked Sharpen blades

Blades worn down too far Replace blades

Engine RPM too low Mow at full throttle

Ground speed too fast Slow down

Deck clogged with grass Clean deck

Belt Adjustment/Replacement

The pump drive belt and blade drive belt are self-

adjusting, and will only need replacement when worn.

Replacing the Cutter Deck Belt

1. Stop the engine, remove the key and wait for all

moving parts to stop.

2. Remove the deck cover.

3. Remove the belt by using a ½” ratchet and

extension to relieve the belt tension.

4. Reinstall in reverse order.

6-4

Replacing the Drive Belt

1. Stop the engine, remove the key and wait for all

moving parts to stop.

2. Remove the deck cover and remove the blade

belt. (Refer to above section)

3. Raise and secure mower

4. Remove the belt by using a ½” ratchet and

extension to relieve the belt tension.

Hydraulic System

When servicing the hydraulic system it is

critical to keep any dirt or debris from getting

into the system. Clean o all parts before

disassembly and assembly.

When any of the hydraulic parts are

disconnected or removed or when the oil is

changed, air must be bled from the system. If

air is entrained in the system, loss of power,

excessive heat, and damage to the hydraulic

pumps may occur.

Bleeding Air from the Hydraulic System

1. Fill the reservoir.

2. Lift the machine so that the rear wheels are o

the ground. Be careful to support the machine

so that it will not fall or tip while the system is

bled of air.

3. With the bypass valves open and the engine

running, slowly move the control levers back

and forth ve or six times.

4. Now close the bypass valves and with the

engine running, slowly move the control levers

back and forth ve or six times.

5. It may be necessary to repeat the above steps

until all the air is purged and the rear wheels

are turning at normal speed.

6. After purging is complete, adjust the oil level in

the reservoir if necessary.

Check Hydro Oil

1. Ensure mower is on a level surface.

2. Lift hinged pad to access the sight-glass

Fill Hydro Oil

1. Lift hinge pad and remove vent cap

2. Use a funnel to ll tank

Lubrication

Your machine is made with sealed bearings and

synthetic dry lubricant bushings; therefore only the

front caster pivots need to be greased.

Grease yearly by either, removing the ¼-28 bolt and

install a grease tting or by removing the dust cap,

disassembling and re-packing the wheel bearings.

Use lithium complex base or compatible grease..

Use care lling with grease gun as too much

pressure could blow out the grease seal.

When re-installing dust cap, use two drops of thread

locker to prevent the dust cap coming o during

operation.

6-5

Spindle/Drive Pulley R&R

1. Remove 2 ¼” bolts from hub and

install in threaded holes in hub.

2. Slowly tighten each bolt,

alternating as you tighten bolts

against pulley.

3. The hub will separate from the

pulley.

4. Replace grade 8 bolts and

install in reverse order using the

assembly holes to tighten hub

onto pulley and spindle shaft.

Do not use a gear puller. It will not pull the hub

o and may frustrate you. Properly performed

this procedure should not require excessive

force.

Cutting Blades

In order to maintain the best cut, it is important that

the blades are well sharpened and not damaged.

Bent or cracked blades or blades with large nicks

need to be replaced. Blades must be balanced after

sharpening. To change the blades:

1. Stop engine, remove the key and wait for all

moving parts to stop.

2. Engage the parking brake

3. Lift front of mower and secure in the raised

position with jack stands.

4. Remove the blade nut by turning

counterclockwise.

5. Install new or re-sharpened blade.

• Ensure the blade spacers are reinstalled with

the same qty and location

6. Torque blade bolt to 70-80 ft./lbs. / 95-108 N

Battery Service

CALIFORNIA Proposition 65 Warning.

Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known by the state of California to

cause cancer and reproductive harm. Wash

hands after handling.

The battery is 12 volts and is a maintenance free

battery. Charge the battery only if it will not start the

machine properly.

Remove the battery from the machine before

charging.

Follow the instructions of the battery charger for

proper and safe charging of the battery.

To access the battery, rst, park the machine safely.

Remove the retainer bolt and remove battery cover.

Follow all warnings and cautions on the battery label

and issued by the battery manufacturer.

Parking Brake Adjustment

To test if the parking brake needs adjustment, inate

tires to the correct pressures.

Stop machine on a maximum 17 degree slope and

apply the brake. Properly adjusted brakes will prevent

the wheels from turning.

If the drive wheels turn, a brake adjustment will be

necessary. Adjustment nuts are located between the

fuel tank and upright.

To adjust brake:

7. Loosen adjustment nuts. (A)

8. Bring brake shoe down until contact is made

with the tire. (B)

9. With brake shoe making contact with the tire,

move the brake handle to approximately 30

degrees and tighten adjustment nuts.

Test parking brake. Adjust again, if required

Loading/Unloading

Use extreme caution when loading and unloading

units on/o trailers or trucks.

One full width ramp that extends beyond the rear

tires is recommended rather than individual ramps for

each side of the unit.

The ramp should be long enough so that the angle

between the ramp and the trailer or truck does not

exceed 15 degrees. A steeper angle may cause the

mower deck components to get caught as the unit

moves from ramp to trailer or truck.

Page is loading ...

WRIGHT STANDER-I-WSTN User manual

Brand: WRIGHT

Model: STANDER-I-WSTN

Type: User manual

Download PDF

report

WRIGHT STANDER-I-WSTN User manual

WRIGHT STANDER-I-WSTN User manual

Related papers

Other documents