ADURO 22.3 Lux User manual

Page is loading ...

34

Congratulations on your new Aduro Stove!

To get the best possible experience and benefit from your new Aduro wood burning stove, it is important that

you read the user manual thoroughly through before you install the stove and start using it. Errors or

incorrect settings can cause hazardous conditions and/or poor operation.

For further information, please go to www.adurofire.com.

5-year warranty – Free online registry

You have the opportunity to extend the warranty on your wood burning stove from two to five years for free.

All you need to do is register the stove at www.adurofire.com/warranty. The deadline for registering is five

months from the date of purchase.

Production number

The wood stove has a production number on the rating plate on the back of the stove. For most of our

stoves, the production number is also stamped on the front page of the user manual. We recommend that

you note down this number in the box below before mounting the wood stove. For the purposes of the

guarantee and for other enquiries, it is important that you are able to quote this number.

Enjoy!

HOW TO SUCCEED WITH YOUR NEW WOOD STOVE

In our customer service center Aduro Customer Service you will

find tips and tricks on how to succeed with your new Aduro wood

burning stove. Here you will have direct access to interesting

content about installation and maintenance of your stove as well

as support related information. Find us here and make the most of

your Aduro wood stove.

UK

35

1. General

1.1 Compliance

The Aduro 22 series complies with the EN13240 European standard as well as the NS3058 Norwegian

standard and is thereby approved for installation and use in Europe. At the same time, the manufacturing

process is subject to external quality control. The Aduro 22 series also carries the Nordic Ecolabel, which

guarantees that the wood burning stove complies with the most stringent environmental requirements and

has been manufactured in an environmentally correct manner. DoP (Declaration of Performance) can be

downloaded at www.adurofire.com/download.

1.2 Technical data

Aduro 22 series

Data

Nominal power

5,5 kW

Flue outlet, diameter

Ø150 mm top/rear

Measurements Aduro 22 (HxWxD)

98,2 x 44 x 40,3 cm

Measurements Aduro 22.1 Lux & Aduro 22.5 Lux (HxWxD)

113 x 44 x 40,3 cm

Measurements Aduro 22.3 Lux (HxWxD)

106,1 x 44 x 40,3 cm

Height exhaust branch above floor Aduro 22

96,1 cm

Height exhaust branch above floor Aduro 22.1 Lux & Aduro 22.5 Lux

111 cm

Height exhaust branch above floor Aduro 22.3 Lux

104,1 cm

Distance from floor to centre of rear outlet Aduro 22

86,5 cm

Distance from floor to centre of rear outlet Aduro 22.1 Lux & Aduro 22.5 Lux

101,3 cm

Distance from floor to centre of rear outlet Aduro 22.3 Lux

94,4 cm

Distance from centre of exhaust branch to rear edge of stove

18,5 cm

Weight Aduro 22

80 kg

Weight Aduro 22.1 Lux & Aduro 22.5 Lux

91 kg

Weight Aduro 22.3 Lux

85 kg

Material

Sheet iron

Fuel

Wood and wood briquettes

Max wood length

35 cm

Convection stove

Primary, secondary, and tertiary air supply

Air-wash system

Ashpan

Energy efficiency

78 %

Energy efficiency index

104,1

Energy efficiency class

A

Chimney draft

12 Pa

Maximum combustion amount per hour (wood)

Ca. 3,1 kg

Heat rating in buildings with

- Optimum insulation

- Average insulation

- Inadequate insulation

150 m

2

100 m

2

60 m

2

36

1.3 Transportation

When taking your wood burning stove home, please ensure that it travels in an upright position. If you wish

to lay it flat, it is important that you remove all loose parts from the combustion chamber (cast iron grate,

baffle plates and loose fireproof tiles) and remove the ashpan. Please use wood from the packaging for the

first use. The plastic packaging should be discarded.

2. Installation of the stove

You are welcome to install your wood burning stove yourself – but we strongly recommend that you consult

your chimney sweep before you begin the installation. It is important to ensure that all local rules and

regulations, including ones relating to national and European standards, are complied with when installing

this device. Your dealer can also provide you with installation advice. Remember, it is your responsibility that

rules in force are complied with.

2.1 Position of the stove / distance requirements

The wood burning stove must be installed in a suitable and physically possible position. You need to be sure

that the position complies with local regulations. Distance requirements will only apply if the wood burning

stove is to be placed close to flammable materials:

Aduro 22, Aduro 22.3 Lux & Aduro 22.5 Lux:

Distance to flammable material (see illustration below)

Behind the

stove

Behind stove with

insulated flue pipe

To the sides

Above the stove

Distance to furniture

15 cm

10 cm

70 cm

75 cm

90 cm

You may not begin to use the stove until it has been inspected and approved

by your local chimney sweep.

37

Aduro 22.1 Lux:

Distance to flammable material (see illustrations below)

Behind the

stove

Behind stove with

insulated flue pipe

To the sides

Above the

stove

Corner

position

Distance to

furniture

15 cm

10 cm

45 cm

75 cm

17,5*/20 cm

90 cm

*with insulated pipe

If the stove is positioned against a brick wall or other non-flammable material, there are no minimum distance

requirements. To facilitate cleaning and for the best use of the convection air, we recommend that you leave

a distance of approximately 5-10 cm to the wall.

If the wood burning stove is to be placed close to flammable material such as a wooden floor or carpet, it

must be placed on a non-flammable base. The floor plate should extend for at least 30 cm in front of the

wood burning stove and 15 cm on each side measured from the opening of the combustion chamber.

2.2 Pipe connection

The Aduro 22 series leaves the factory with the flue outlet mounted on the top. If you require the flue outlet

on the back, “breake” the two cover plates on top of the back of the stove. Exchange the exhaust connector

(from the top outlet) with the cover plate from the rear outlet. Mount the cover plate from the rear outlet to the

top outlet. The top outlet is finished with the plate that lies in the ashpan. A flue pipe with an internal diameter

of 150 mm should be used for Aduro stoves. The Aduro 22 series is suitable for installation in a shared flue.

Please ensure that all local rules and regulations are complied with, including CE marking of the flue pipe.

Additionally, distance requirements to flammable material for the pipe must be respected.

The wood burning stove must be installed on a floor with the adequate load-

bearing capacity. If the existing construction does not meet this requirement,

appropriate adaptation measures must be taken (e.g. a load-distributing plate).

38

2.3 Connection to a brick chimney

If the stove is being connected to a brick chimney, the rear outlet or a curved flue pipe via the top outlet

should be used. After measuring, a hole is made in the chimney in which the pipe sleeve is placed and stove

mortar is used to seal it in place. The stove is placed in position and the flue pipe is put in place. A thin

gasket is placed between the flue pipe and the pipe sleeve to seal the joints. The flue pipe should protrude

into the pipe sleeve, but must not block the opening in the chimney (see the illustration below):

The stove can be connected to a chimney to which other heat sources are connected.

2.4 Supply of combustion air

All wood burning stoves need constant supply of air to ensure a clean and efficient combustion. This is often

a problem in modern energy-efficient houses that are very tight. Therefore, the Aduro 22 series is equipped

with external supply of combustion air, where the air to the combustion is supplied from the outside and

directly into the wood burning stove. Air from the outside can be provided through a channel, which is

connected to the connecting pipe under the combustion chamber. The amount of air needed for combustion

is 25m3/h. Air vents must be positioned where they cannot be blocked.

The connecting pipe has an external diameter of 78 mm, to which you need a pipe with a diameter of 80 mm.

If the pipework is more than 100 cm, or if there are bends on the tube, the resistance in the pipe increases

significantly. Negative pressure outside on the sheltered side of the house can also affect the resistance of

the pipe significantly. In these situations, the pipe should have a diameter of minimum 100 mm. It may also

require a stronger chimney draft, which you can achieve by installing an Aduro DraftOptimizer. You can

easily test the resistance in the pipe by opening a window close to the stove, disconnect the external air

supply and then light up the stove. If the combustion looks different than before, there is too much resistance

in the external air supply. If the pipe work is further than 1 m, the pipe diameter must be increased to 100

mm and a correspondingly larger wall valve must be chosen. In warm rooms the channel should be insulated

with 30 mm mineral wool covered with a damp-proof course (plastic). It is important that the lead-in between

the pipe and the wall (or floor) is sealed with jointing compound. You can eventually use the complete Aduro

fresh air kit.

The pipe with external supply of combustion air can be taken out at the bottom of the back side of the stove

or under the stove (see illustration below):

X

39

If you want to use the wood burning stove without connecting the supply of combustion air, “breake” off the

cover plate in the rear cover at the bottom of the back of the stove.

2.5 Options for installation

Indirect through

external wall

Through floor

and foundation

Through

wall

Trough floor and

crawl space

Aduro 22, Aduro 22.1 Lux & Aduro 22.5 Lux

40

Do not install the stove in the following ways:

3. Lighting the stove

Important safety information

• The wood burning stove will become warm during use and therefore it should be treated with all

necessary caution.

• Never keep easily combustible fluids such as petrol in the vicinity of the wood burning stove.

• Never use easily combustible fluids to light the fire in the wood burning stove.

• When lighting a fire, it is important to get the fire burning fast. If the fire does not start quickly and

wood only smoulders, it can cause strong smoke formation and in worst case cause an explosive

ignition of the flue gasses, which can damage the stove.

With air intake upwards:

Through a damp crawl space:

If the air is drawn from a damp crawl

space, you won’t achieve an optimum air

intake.

If the air intake is turned upwards,

there will be too much resistance for

the air intake.

Aduro 22.3 Lux

41

• Never empty the ashpan when the wood burning stove is warm. Embers may still be found in the

ashpan for up to 24 hours after the fire has gone out. Please wait to empty the ashpan until you

are sure that there are no embers in the ash.

• The door should be kept closed while the wood burning stove is in use. While lighting the fire, the

door can stand ajar for the first few minutes.

• In the event of a chimney fire: Close all the dampers on the wood burning stove and call the fire-

fighting service.

3.1 Damper

The stove is equipped with a damper under the door, which regulates the combustion air: primary,

secondary, and tertiary air supply. The primary air is used at the beginning to get the fire going, the

secondary air keeps the fire burning evenly, and the tertiary air ensures that flue gasses are burned. You

must always add secondary and tertiary air, while firing the stove.

The damper allows you to adjust the stove according to the chimney draft and the heat output you require.

The longer the damper is pulled out, the more air is added and the more powerful the combustion. The

illustration below shows the stove seen from the front with the dampers indicated. Use edge of door to read

position of inlet air:

3.1.1 Secondary air supply

In normal circumstances, the wood burning stove should be working with this damper open between 60 %

and 100 %. You should never close the air intake so far that the flames are extinguished. There should

always be visible flames in order to achieve clean and efficient combustion. A too low supply of air can lead

to bad combustion, high emissions and a bad efficiency. The air-wash system that minimizes soot collecting

on the glass panes is also adjusted by this damper.

If you want to fire the stove with the lowest effect possible – around 3 kW – you must close the secondary

damper almost completely 45 minutes after the wood has been put in. At this point there are only few flames

and the stove can burn clean by using the tertiary air from behind in the stove.

1: Fully open primary, secondary, and tertiary air inlet.

This position can be maintained with the Aduro key,

which must be placed in the two holes.

2: Closed primary air inlet, fully open secondary and

tertiary air inlet.

3: Closed primary air inlet, half way closed secondary

air inlet and fully open tertiary air inlet.

4: Closed primary and secondary air inlet, fully open

tertiary air inlet.

5: Regulator pushed all the way in. All air inlet closed.

42

3.1.2 Primary damper

When you add a new log, the primary damper should be opened until the fire is burning properly. In order to

utilize the fuel to the fullest extent, the embers should have burnt for so long that it is necessary to open the

primary damper for approx. 2 minutes to get the new log to burn.

In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel, it is a good

idea to open the primary damper for approx. 1 minute before the door is opened. This increases the draft

through the stove and reduces the risk that ash will drop on the floor.

3.2 Aduro-tronic

The patent-applied control Aduro-tronic is a manually operated mechanical start-up

device, which works without the use of electricity and automatically regulates the

combustion. All you have to do is put dry wood in the stove and activate the control

system. Aduro-tronic does the rest, leaving you to enjoy the flames, the benefits of

efficient combustion, and a reduced firewood usage up to 40 %. For further

information, go to www.adurofire.com.

3.2.1 How to operate Aduro-tronic

When lighting

When lighting a fire in the stove for the first time, the maximum amount of primary

air will be needed to light the fire. For that reason, the primary damper can be kept

“forcibly open”. This is done by pulling the primary damper forward as far as

possible and then fixing it with the Aduro Key (see illustration). When the stove is

warm and a layer of embers has been created on the bottom of the combustion

chamber, the Aduro-tronic can be set to the automatic position, i.e. the Aduro Key

can be removed. Alternatively, you can leave the door ajar the first minutes during

lighting the fire (without the key).

When stoking

Each time fresh wood is put in the stove, a precise amount of primary air will be

allowed in for the first few minutes. What’s more important is that the primary air is not allowed in for too

long. This is to ensure optimum combustion. The Aduro-tronic control will ensure intake of primary air at the

right tempo. The automatic is activated by pulling the primary damper out each time fresh wood is put in the

stove. The automatic closes then the primary air gradually.

Regulation of the Aduro-tronic control

The control is pre-set to close the primary air intake within 6 minutes. This setting has been used during

testing at the Danish Technological Institute using a standard chimney and ‘standard’ sized logs (approx. 30

cm long, 10x10 cm thick) with maximum moisture content of 18%. In practice, such circumstances can differ,

If you overload the wood burning stove and burn more than approx. 3.1 kg

wood/hour, there is a risk that the lacquered surface of the stove will become

discoloured and eventually fall off. The stove can be resurfaced, but this is not

covered by the manufacturer’s guarantee. In the same way, any other damage to

the stove caused by overloading will not be covered by the guarantee.

43

which is why the Aduro-tronic control can be adjusted to your circumstances. If you want a slower intake of

primary air (e.g. for a slower flue draft, larger sized wood or for longer intervals between stoking), adjust the

screw on the front of the control level using a small allen key to slow closure rate. If the screw is turned to the

right, closing time is increased and if turned to the left, closing time is reduced.

3.3 How should I use my wood burning stove?

The wood burning stove is intended for intermittent combustion. This means that each stoking should burn

down to embers before new logs are added. Please respect the max load line when adding wood logs.

To obtain the best possible combustion, you should regulate the effect/heat output with the fuel. Burning

small logs provides more powerful combustion than burning large logs as the surface area is greater and

more gas is released. The amount of wood in the combustion chamber is another factor that affects

combustion. The optimum combustion is achieved by placing two logs in the stove. If you want an enhanced

effect, you can add more logs. The ideal heat output is reached by burning approx. 1.8 kg per hour.

If you experience problems lighting the fire or the fire dies after a short time, it can be due to the following

reasons:

• The fire wood is not dry enough. The fire wood should have a moisture content of max. 18%.

• There is a negative pressure in the house.

• The smoke outlet from the outside may be blocked from sooth. This can occur after chimney

sweeping. Control the smoke outlet.

• The used amount of wood may have been too small. Therefore, the embers were too weak and cold

to light the next load of wood.

3.4 The first time a fire is lit

The wood burning stove is packed in recycling packaging. The wood from the packaging can be sawed into

smaller pieces and used the first few times a fire is lit. The plastic packaging must be disposed according to

national rules regarding disposal of waste.

During transportation, it may happen that the baffle plate in steel falls out of place. Therefore, before using

the stove, please make sure that the baffle plate is properly placed (on the hooks or fastened to the bolts

depending on the model) for optimum combustion and preventing soot on the glass.

The first few times the wood burning stove is used, there may be some smoke and unpleasant odours from

the wood burning stove, which is fairly normal. This is caused by the heat-resistant paint hardening. Make

sure there is sufficient ventilation during this stage. It is also important not to let the fire burn too fiercely the

first 2-3 times, so that the wood burning stove has time to expand slowly.

You should also be aware that the stove may make some clicking sounds as it heats up and cools down –

like pouring boiling water into a sink. These are caused by the great differences in temperature to which the

materials are being exposed.

Use of dry wood of the right size is important to achieve optimum

combustion.

During the first firing, which should be carried out using approximately 1 kg of

wood, the stoking door must be left slightly open and must not be closed until

the stove is cold. This is to prevent the sealing rope sticking to the stove.

44

3.5 Lighting a fire in the wood burning stove

The fire lighting method is very important for starting combustion quickly and efficiently.

1. Pull the damper under the door forward to open primary, secondary, and tertiary air supply.

2. Place a log of wood crosswise in the combustion chamber and put 2 firelighters close to the log.

Light the firelighters and quickly put a new log close to the firelighters and several small logs at an

angle above it. Air must be able to reach the firelighters, but the logs should be touching to “warm”

each other.

3. Keep the door approx. 1 cm ajar, until the glass is too hot to touch. Then close the door. When there

are distinct, visible flames and the fire has taken hold, close the primary air intake/damper (see

section 3.1.2).

3.6 Recommended fuels

Wood and wood briquettes. We recommend the use of split hardwood that has been stored outdoors under

cover for at least 1 year. Wood that has been stored indoors has a tendency to become too dry and will burn

too quickly. We recommend that you fell the wood during the winter when a lot of the moisture in the wood

will have been drawn down into the roots. In order to achieve optimum combustion, the wood’s moisture

level should not exceed 18 %, which roughly corresponds to storing the wood under cover outdoors for one

year. The moisture level of the wood can be measured using a moisture meter or by applying dishwashing

liquid to one end of the log and blowing air in the other end. If the wood is dry enough, soap bubbles will

appear. The wood should be chopped into logs with a diameter of approx. 10 cm and a log length of max. 35

cm. Firing with wet fuel will reduce the energy efficiency and increase the particle emission.

Burning varnished wood, impregnated wood, chipboard, paper, and other waste is strictly forbidden. Burning

these materials will damage the environment, the wood burning stove, and your own health. Fossil fuels

must not be used.

4. The chimney

The optimum combustion is achieved at a constant chimney draft of 10-14 Pascal (Pa) measured in the flue

pipe above the stove (when having a smoke exhauster). However, with natural draft (chimney without smoke

exhauster) the draft in the chimney will be between 18-25 Pa when conditions are optimum. There are many

factors that affect the chimney draft, including the outside temperature, wind strength, and surrounding

buildings. There are no requirements with respect to specific chimney heights, but a chimney must be tall

enough to provide a good draft. If the recommended chimney draft is not achieved, there may be problems

with smoke out of the door by firing.

The control handles will get warm when the wood burning stove is in use.

Please use the glove provided when you operate the wood burning stove.

45

Data for chimney calculation

Wood

Flue temperature at [20°C]

286

Chimney draft at testing power [mbar]/[Pa]

0.12 / 12

Flue gas mass flow [g/s]

5.5

4.1 Inadequate draft in the chimney

If you experience poor draft in the stove after the installation, please make sure that there is nothing in the

chimney to restrict the smoke and that no nearby buildings or trees affect the winds around the chimney.

If the chimney is too short, leaks, or is inadequately insulated, there may be problems with the chimney draft

(let the chimney sweep assess this). The draft should be sufficient during the ignition phase when the

stove/chimney is cold to provide a clean combustion and prevent smoke leakage. Therefore, we recommend

a chimney draft around 5 Pa in the ignition phase.

Once the ignition is a success and the smoke temperature is rising, it is important that the chimney draft

reaches a stable area around 18-25 Pa in operation (1 hour after ignition) when the chimney/stove is hot.

The draft in the area of 18-25 Pa when the stove is hot is essential in order to achieve an optimum and clean

combustion. Therefore, we recommend that you measure your chimney draft when the chimney is cold and

when it is hot after 1 hour in operation.

In practice, the chimney draft will differ – especially in cold condition. Therefore, the best indication of the

chimney draft is to measure the draft when it is hot. If the chimney sweep judges the draft to be sufficient, but

you still have problems lighting a fire, try extending the fire lighting phase by using more thin pieces of

kindling and 1-2 firelighters, so that the chimney gets thoroughly warm. The chimney will not draw at

optimum effect until it is warm. When a layer of embers has been formed, add 2-3 dry logs.

If it is impossible to establish a sufficiently natural chimney draft, the chimney can be fitted with a smoke

exhauster, e.g. Aduro DraftOptimizer.

4.2 Chimney and Smoke

If you experience smoke coming out of the stove or the start section of the smoke pipe, it could be due to

certain weather conditions. On stormy or cold winter days or if the chimney has not been used in a while, a

cold plug can be created in the chimney, meaning the natural draft will be at its minimum.

If the chimney is cold and cold plugs are created, you may experience smoke leaks during the ignition and

startup phase. In this situation there can be more smoke than usually in the combustion chamber and some

of it might leak out of the stove. Therefore, if you have a cold chimney that has not been used for a while, we

recommend that you use some wood sticks to heat the chimney and eliminate the cold plug.

5. Maintenance and cleaning of the stove

All maintenance and cleaning of the stove should be carried out when it is

cold.

46

Combustion chamber

The fireproof tiles in the combustion chamber eventually wear out and should be replaced when the cracks

are more than 0.5 cm. The durability of the tiles depends on how often and how intensively the stove is used.

You can change the tiles yourself. They are available as a ready-to-use set. For further information, go to

www.aduroshop.com.

How do I remove the Bauart spring?

All Aduro stoves are fitted with a “Bauart” safety spring. The mechanism ensures that the door of the stove

closes automatically. The “Bauart” spring is only a law requirement in Germany.

How to remove it:

• If you wish to remove or replace the spring with a new one it is possible to cut the spring using a

pincer. It is advisable to hold the spring with pliers or cover it with a cloth or other device to absorb

the tension, as the pieces might spring out right after the cut.

• Please note that the spring is in tension when the door opens, so make sure to protect yourself

during fitting and removal.

Glass

Wet wood, unsatisfactory chimney draft, and wrong use of the stove can leave soot stains on the glass pane.

They can easily be removed using a damp cloth that you dip in cold ash and rub on the sooty glass. Special

cleaning agents are also available to remove soot from glass, e.g. the Aduro Easy Clean pad. The pad

neither scratch nor damage the glass and is for multiple usage. Water or other cleaning agents are not

necessary.

It is common maintenance to tighten the glass fittings shortly after the stove has been installed as well as to

check if the gaskets are properly placed.

Gaskets

With time, gaskets around glass and door will wear. We recommend that you inspect them regularly. If

leakages appear, they must be replaced.

Ashes

Empty the ashpan before it gets completely full. Always leave a layer of ashes in the stove because it

insulates and makes it easier to light a fire.

Cleaning the stove

The stove’s surface is treated with a heat-resistant Senotherm® paint, which will stay at its best just by being

vacuumed with a small, soft mouthpiece or dusted with a soft, dry cloth. Do not use spirit or other solvents, as

they will remove the paint.

Do not clean the stove with water. If the stove is exposed to moisture, the stove

may develop rust.

47

The inside of the stove and the flue pipe can be cleaned through the door or alternatively through the

cleaning aperture in the flue pipe/chimney. The upper fireproof tile (the baffle plate) can be removed. To

allow free access to the top of the stove and the flue pipe, remove the baffle plate in steel. The flue pipe can

be removed from the stove and cleaned. Cleaning of the inside of the stove and the flue pipe should be

undertaken at least once a year, or more frequently if necessary, depending on how often the stove is used.

This work can also be carried out by the chimney sweep or your local Aduro GO partner.

Repairing the surface

Aduro stoves are painted with a heat-resistant paint that can withstand temperatures up to 500 degrees. If

the surface of the stove gets scratched or worn, it can easily be renewed using this type of paint. Everybody

can repair the surface and obtain a perfect result. The paint is available in black metallic from your local

dealer or at www.aduroshop.com.

Spare parts and unauthorized alterations

You may only use original spare parts for your stove. All forms of unauthorized alterations to the stove are

strictly forbidden, as the stove will no longer comply with the approved specifications. At

www.aduroshop.com you can buy original spare parts for your stove.

6. Accessories

For Aduro stoves we offer a wide product range of accessories to fulfil the experience: Companion sets,

firewood baskets and buckets, fireplace grid, briquette buckets, floor hearths in glass and steel, flue pipes,

Aduro Easy Firelighter, and Aduro Easy Clean pad. For further information, go to

www.adurofire.com/accessories.

7. Right of complaint

In accordance with the Danish Sale of Goods Act, you have a two-year right of complaint from the date of

purchase of the wood burning stove. The dated receipt will be sufficient proof. The right of complaint does

not cover damages caused by faulty installation and use of the stove. The right of complaint also does not

cover loose and wearing parts (fireproof tiles, glass, gaskets, slides, painted surfaces, cast iron gate, and

handles) as they are subject to wear during normal use. These parts can be bought as spare parts in our

online shop www.aduroshop.com.

In addition, the right of complaint does not cover:

• Damages resulting from incorrect installation and use of the stove, e.g. overheating and wrong or

missing maintenance of the stove.

• Damages caused by (condensation) water in and around the chimney, too much or too little draft in

the chimney and missing maintenance/cleaning.

• Mounting or demounting relating to repairs.

• Transportation costs relating to repairs.

48

• Damages to the stove caused by external influences or damages caused by the stove on other

objects.

Page is loading ...

ADURO 22.3 Lux User manual

This manual is also suitable for

ADURO 22.3 Lux User manual

in other languages

Related papers

Other documents