DHP Victoria Owner's manual

DO NOT RETURN TO THE STORE !

Visit www.dhpfurniture.com/eng/support-home

or call Toll-Free 1-800-267-1739

4092239

B34409223900 - 241637-C

Date of Purchase

Victoria Metal Bed

K.W. - 2016/6/1

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Queen

Bronze

Weight Limit: 500 Lb / 227 Kg

Contact Us!

cs@dhpfurniture.com

DHP

410E, First Street South, Wright City, MO 63390, USA

Attention: Consumer Service.

Read Before Beginning Assembly

1-800-267-1739

Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)

Warranty Information

2

B34409223900

Caution

DHP warrants this product to be free from defects in material and workmanship and

agrees to remedy any such defect. This warranty covers one year from the date of

original purchase. This is solely limited to the repair or replacement of defective

parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly assembled,

subjected to misuse or abuse or which has been altered or repaired in any way.

Liability for consequential damages is excluded to the extent exclusion is permitted

by law. This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

To obtain warranty service, purchaser must present original bill of sale. Components

repaired or replaced are warranted through the remainder of the original warranty

period only. The defective components will be repaired or replaced without charge,

subject to the terms and conditions described above.

Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and

Canada.

 Call our toll free number if you need assistance.

 Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and product.

 Recommended # of people needed for assembly: 2 (however it is always better

to have an extra hand). Estimated assembly time is 2 hours.

 Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

 Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

 This product is designed for home use and not intended for commercial use.

 This product contains small components. Please ensure that they are kept away

from small children.

 Do not use power tools to assemble your furniture. Power tools may strip or

damage the parts.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Page is loading ...

4

Parts

B34409223900

All in 1 big box!

Before you throw the package, please use the

Check Box to identify the parts and ensure that

you have all the parts needed for the assembly.

There are inner box(es) that include components

required to complete this assembly.

Replacement Parts, Visit www.dhpfurniture.com/eng/support-home

Headboard

T938640

X2

Post 01

T938600

X1

Post 02

T938610

X1

Post 03

T938620

X1

Post 04

T938630

X1

E

A1

H

I

G

S

K

Ball

T918500

X4

Side Rail 01

T938250

X2

Side Rail 02

T938260

X2

Brace 01

T938280

X1

Brace 02

T938290

X2

Brace 03

T938300

X2

Slat

T933150

X14

Bracket

T938310

X1

Leg 01

T937730

X3

Leg 02

T937740

X3

Plug

T932590

X28

B

C

F

I

H

K

O1

G

Y

L

D

A

O1

L

M

Y

S

A

B

C

D

E

M

F

A1

5

Hardware Pack

B34409223900

Hardware Pack #: T4092229-00

Hardware Note:

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step

instructions.

1/4" X 11/16"

x4

2

5/16" X 3/4"

x16

4mm

x1

1/4" X 7/8"

x20

1/4" X 1 9/16"

x4

1/4"

x4

4

5

6

1/4"

x8

X1

8

1

7

3

DK

DL

6

B34409223900

x8

X8

2

6

Step 1

Insert (A1) into (A) & (B) with BOLTS 2 and

CURVED WASHER 6.

Insert (A1) into (C) & (D) with BOLTS 2 and

CURVED WASHER 6.

A

B

A1

C

D

A1

Correct: Part (A1) peretrating

through Part (A)/(B)/(C)/(D).

Wrong: Part (A1) NOT peretrating

through Part (A)/(B)/(C)/(D).

B

A1

7

B34409223900

X4

Step 2

Insert (F) X2 into (E) x2 with BOLTS 4.

4

F

E

F

E

DU

DV

8

B34409223900

x8

2

Step 3

3.1 Attach (H) x2 to sub-assembly (E/F)

x2 from STEP 2 with BOLTS 2.

3.2 Attach (G) to (E) X2 with BOLTS 2.

H

E

F

H

G

F

E

H

F

2

G

E

2

3.1

3.2

DW

9

B34409223900

x4

Attach (L) x 2 to (G) with BOLT 2.

Step 4

This bed offers you 2 options for the height

of the bed foundation.From STEP 4 to

STEP 9 will show you how to assemble the

bed foundation in the lower position.

If you intend to assemble the bed

foundation in the higher position,

please start from Step 10.

G

L

2

L

G

2

EA

EB

10

B34409223900

x16

3

Step 5

Attach (E) & (F) to (A), (B) , (C) & (D) with

BOLTS 3

Wide side of the slot should

be facing up !

A

F

3

A

B

C

D

F

E

F

E

EC

ED

11

B34409223900

x2

6.1 6.2

1

5

Step 6

6.1 Insert one end of both (I) into the slot on

(G) as illustrated.

6.2 Attach the other end of both (I) to (H)

with BOLTS 1 and NUTS 5.

1

H

5

I

G

I

H

I

H

G

EE

12

B34409223900

x2

5

Step 7

Attach (L) & (K) to (G) with BOLTS 1 and

NUTS 5.

1

K

5

L

G

I

L

G

1

13

B34409223900

8.1

1

2

3

O1

Y

E

Step 8

8.1 Insert (O1) into (E & F) as illustrated:

8.2 Lock (O1) into place with (Y).

8.2

E

F

E

O1

EF

14

B34409223900

Step 9

Attach (S) x4 to (A), (B), (C) & (D).

S

B

A

B

C

D

S

EG

15

B34409223900

X4

Step 10

From Step 10 to Step 15 will show you how

to assemble the bed foundation in the lower

position.

Attach (M) X 2 to (G) with BOLTS 2.

M

G

M

G

M

2

EH

EJ

16

B34409223900

X16

Wide side of the slot should

be facing up !

3

Step 11

Attach (E) & (F) to (A), (B), (C) & (D) with

BOLTS 3.

3

A

F

E

F

A

B

C

D

FL

FM

17

B34409223900

x2

1

5

Step 12

12.1 Insert one end of both (I) into the slot

on (G) as illustrated.

12.2 Attach the other end of both (I) to (H)

with BOLTS 1 and NUTS 5.

I

G

I

H

I

G

H

I

5

1

12.1

12.2

FK

18

B34409223900

x2 x2

5

Step 13

Attach (M) & (K) to (G) with BOLTS 1 and

NUTS 5.

5

1

G

M

K

1

19

B34409223900

14.1

1

2

3

14.2

Step 14

14.1 Insert (O1) into (E & F) as illustrated:

14.2 Lock (O1) into place with (Y).

O1

E

O1

E

F

E

F

O1

FF

20

B34409223900

Step 15

Attach (S) x4 to (A), (B), (C) & (D).

S

A

B

C

D

S

B

21

Helpful Hints

B34409223900

 Move your new furniture carefully, with two

people lifting and carrying the unit to its new

location.

 Your DHP furniture can be disassembled and

reassembled to move.

 Some parts have been pre-assembled for this

item. They are illustrated on this page and available

for replacement.

WARNINGS:

For safety reasons and to prevent injuries:

 This bed is not intended for use by children under 4

years old.

 Prohibit jumping and horseplay on this bed.

 Only use a mattress which is 79"-80" long and 59" -

60" wide.

 Do not use risers under this bed.

Helpful Hints

Weight Limit: 500 Lb / 227 Kg

End Cap 1

T392480

x4

End Cap 2

T392520

x3

Page is loading ...

DHP Victoria Owner's manual

This manual is also suitable for

DHP Victoria Owner's manual

in other languages

Related papers

Other documents