DO NOT RETURN TO THE STORE !
Visit www.dhpfurniture.com/eng/support-home
or call Toll-Free 1-800-267-1739
4092239
B34409223900 - 241637-C
Date of Purchase
Victoria Metal Bed
K.W. - 2016/6/1
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
2014 Dorel Home Products All Rights Reserved
Queen
Bronze
Weight Limit: 500 Lb / 227 Kg
Contact Us!
cs@dhpfurniture.com
DHP
410E, First Street South, Wright City, MO 63390, USA
Attention: Consumer Service.
Read Before Beginning Assembly
1-800-267-1739
Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)
Warranty Information
2
B34409223900
Caution
DHP warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers one year from the date of
original purchase. This is solely limited to the repair or replacement of defective
parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way.
Liability for consequential damages is excluded to the extent exclusion is permitted
by law. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
To obtain warranty service, purchaser must present original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty
period only. The defective components will be repaired or replaced without charge,
subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
Call our toll free number if you need assistance.
Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
Recommended # of people needed for assembly: 2 (however it is always better
to have an extra hand). Estimated assembly time is 2 hours.
Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
This product is designed for home use and not intended for commercial use.
This product contains small components. Please ensure that they are kept away
from small children.
Do not use power tools to assemble your furniture. Power tools may strip or
damage the parts.
For help with assembly, identifying parts, product information or to order parts,
please contact us:
Page is loading ...
4
Parts
B34409223900
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
Headboard
T938640
X2
Post 01
T938600
X1
Post 02
T938610
X1
Post 03
T938620
X1
Post 04
T938630
X1
E
A1
H
I
G
S
K
Ball
T918500
X4
Side Rail 01
T938250
X2
Side Rail 02
T938260
X2
Brace 01
T938280
X1
Brace 02
T938290
X2
Brace 03
T938300
X2
Slat
T933150
X14
Bracket
T938310
X1
Leg 01
T937730
X3
Leg 02
T937740
X3
Plug
T932590
X28
B
C
F
I
H
K
O1
G
Y
L
D
A
O1
L
M
Y
S
S
A
B
C
D
E
M
F
A1
5
Hardware Pack
B34409223900
Hardware Pack #: T4092229-00
Hardware Note:
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
1/4" X 11/16"
x4
2
5/16" X 3/4"
x16
4mm
x1
1/4" X 7/8"
x20
1/4" X 1 9/16"
x4
1/4"
x4
4
5
6
1/4"
x8
X1
8
1
7
3
DK
DL
6
B34409223900
x8
X8
2
6
Step 1
Insert (A1) into (A) & (B) with BOLTS 2 and
CURVED WASHER 6.
Insert (A1) into (C) & (D) with BOLTS 2 and
CURVED WASHER 6.
A
B
A1
C
D
A1
Correct: Part (A1) peretrating
through Part (A)/(B)/(C)/(D).
Wrong: Part (A1) NOT peretrating
through Part (A)/(B)/(C)/(D).
B
B
A1
A1
7
B34409223900
X4
Step 2
Insert (F) X2 into (E) x2 with BOLTS 4.
4
F
E
F
E
DU
DV
8
B34409223900
x8
2
Step 3
3.1 Attach (H) x2 to sub-assembly (E/F)
x2 from STEP 2 with BOLTS 2.
3.2 Attach (G) to (E) X2 with BOLTS 2.
H
E
F
H
G
F
E
H
F
2
G
E
2
3.1
3.2
DW
9
B34409223900
x4
Attach (L) x 2 to (G) with BOLT 2.
Step 4
This bed offers you 2 options for the height
of the bed foundation.From STEP 4 to
STEP 9 will show you how to assemble the
bed foundation in the lower position.
If you intend to assemble the bed
foundation in the higher position,
please start from Step 10.
G
L
L
2
L
G
2
EA
EB
10
B34409223900
x16
3
Step 5
Attach (E) & (F) to (A), (B) , (C) & (D) with
BOLTS 3
Wide side of the slot should
be facing up !
A
F
3
A
B
C
D
F
E
F
E
EC
ED
11
B34409223900
x2
x2
6.1 6.2
1
5
Step 6
6.1 Insert one end of both (I) into the slot on
(G) as illustrated.
6.2 Attach the other end of both (I) to (H)
with BOLTS 1 and NUTS 5.
1
H
5
I
G
I
I
H
I
I
H
G
EE
12
B34409223900
x2
x2
5
Step 7
Attach (L) & (K) to (G) with BOLTS 1 and
NUTS 5.
1
K
5
L
G
I
L
G
1
13
B34409223900
8.1
1
2
3
O1
O1
Y
E
E
Step 8
8.1 Insert (O1) into (E & F) as illustrated:
8.2 Lock (O1) into place with (Y).
8.2
E
F
F
E
O1
EF
14
B34409223900
Step 9
Attach (S) x4 to (A), (B), (C) & (D).
S
B
A
B
C
D
S
EG
15
B34409223900
X4
Step 10
From Step 10 to Step 15 will show you how
to assemble the bed foundation in the lower
position.
Attach (M) X 2 to (G) with BOLTS 2.
M
G
M
G
M
2
2
EH
EJ
16
B34409223900
X16
Wide side of the slot should
be facing up !
3
Step 11
Attach (E) & (F) to (A), (B), (C) & (D) with
BOLTS 3.
3
A
F
F
E
E
F
A
B
C
D
FL
FM
17
B34409223900
x2
x2
1
5
Step 12
12.1 Insert one end of both (I) into the slot
on (G) as illustrated.
12.2 Attach the other end of both (I) to (H)
with BOLTS 1 and NUTS 5.
I
G
I
H
H
I
I
G
H
I
5
1
12.1
12.2
FK
18
B34409223900
x2 x2
5
Step 13
Attach (M) & (K) to (G) with BOLTS 1 and
NUTS 5.
5
5
1
1
G
M
K
1
19
B34409223900
14.1
1
2
3
14.2
Step 14
14.1 Insert (O1) into (E & F) as illustrated:
14.2 Lock (O1) into place with (Y).
O1
O1
E
O1
E
F
E
E
F
O1
FF
20
B34409223900
Step 15
Attach (S) x4 to (A), (B), (C) & (D).
S
A
B
C
D
S
S
B
21
Helpful Hints
B34409223900
Move your new furniture carefully, with two
people lifting and carrying the unit to its new
location.
Your DHP furniture can be disassembled and
reassembled to move.
Some parts have been pre-assembled for this
item. They are illustrated on this page and available
for replacement.
WARNINGS:
For safety reasons and to prevent injuries:
This bed is not intended for use by children under 4
years old.
Prohibit jumping and horseplay on this bed.
Only use a mattress which is 79"-80" long and 59" -
60" wide.
Do not use risers under this bed.
Helpful Hints
Weight Limit: 500 Lb / 227 Kg
End Cap 1
T392480
x4
End Cap 2
T392520
x3
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
