Panasonic SLSX285 Operating instructions

Brand: Panasonic

Model: SLSX285

Type: Operating instructions

Supplied Accessories

Check the packing carton for these accessories.

Model No. SL-SX285

Before connecting, operating or adjusting this product, please read these

instructions completely. Please keep this manual for future reference.

Portable CD player

Operating Instructions

The model number and serial number

of this product can be found on either

the back or the bottom of the unit.

Please note them in the space provid-

ed below and keep for future refer-

ence.

MODEL NUMBER

SERIAL NUMBER

Precautions

Before using this unit, be sure to read the applicable

items of the operating instructions and these safety sug-

gestions carefully.

Afterwards keep them handy for future reference. Take

special care to follow the warnings indicated on the unit

itself as well as in the operating instructions.

Safety

1. Power Source—The unit should be connected to

power supply only of the type described in the oper-

ating instructions or as marked on the unit. Use only

the AC adaptor or car adaptor described in the oper-

ating instructions when recharging.

2. Polarization—If the unit is equipped with a polarized

AC power plug (a plug having one blade wider than

the other), that plug will ﬁt into the AC outlet only one

way. This is a safety feature. If you are unable to in-

sert the plug fully into the outlet, try reversing the

plug. If the plug should still fail to ﬁt, contact your

electrician to replace your obsolete outlet. Do not de-

feat the safety purpose of the polarized plug.

3. Care of AC adaptor—Take care that the cord of the

AC adaptor should be routed so that they are not

likely to be walked on or pinched by items placed

upon or against them. Never take hold of the AC

adaptor if your hand is wet, and always grasp the

plug body when connecting or disconnecting it.

4. Nonuse Periods—When not in use, be sure to dis-

connect the AC adaptor from the AC power outlet.

5. Batteries—If the set is not used for a long period of

time or is used only from an AC power source, re-

move all the batteries to prevent potential damage

due to possible battery leakage. Do not mix batteries

(old and new) or different types of batteries.

Installation

∫ Environment

1. Water and Moisture—Do not use this unit near

water—for example, near a bathtub, washbowl,

swimming pool, or the like. Damp basements should

also be avoided.

2. Condensation—Moisture may form on the lens in

the following conditions...

2. ≥immediately after a heater has been turned on.

2. ≥in a steamy or very humid room.

2. ≥when the unit is suddenly moved from a cold envi-

ronment to a warm one. If moisture forms inside

this unit, it may not operate properly. To correct this

problem wait about one hour for the moisture to

evaporate.

3. Heat—Never use or place this unit near a heat

source. Do not leave it in an automobile exposed to

direct sunlight for a long time with the doors and win-

dows closed as this may deform the cabinet.

∫ Placement

1. Foreign Material—Care should be taken so that ob-

jects do not fall into and liquids are not spilled into

the unit. Do not subject this unit to excessive smoke,

dust, mechanical vibration, or shock.

2. Magnetism—The unit should be situated away from

equipment or devices that generate strong magnetic

ﬁelds.

3. Stacking—Do not place any objects, on top of the

unit.

4. Wall or Ceiling Mounting—The unit should not be

mounted to a wall or ceiling, unless speciﬁed in this

operating instructions.

Maintenance

(See page 7 for details.)

Clean the cabinet, panel and controls with a soft cloth

lightly moistened with mild detergent solution.

Do not use any type of abrasive pad, scouring powder

or solvent such as alcohol or benzine.

Service

1. Damage Requiring Service—The unit should be

serviced by qualiﬁed service personnel when:

1. (a) The AC adaptor is damaged; or

1. (b) Objects have fallen or liquid has been spilled

into the unit; or

1. (c) The unit has been exposed to rain; or

1. (d) The unit does not appear to operate normally or

exhibits a marked change in performance; or

1. (e) The unit has been dropped, or the enclosure

damaged.

2. Servicing—The user should not attempt to service

the unit beyond that described in the operating in-

structions. All other servicing should be referred to

an authorized service personnel.

2. In the U.S.A., contact the Panasonic Customer

2. Call Center at 1-800-211-7262, or e-mail

2. [email protected], or web site

2. (http://www. panasonic.com).

2. In Canada, contact Panasonic Canada Inc.

2. Customer Care Centre at 905-624-5505, or web

2. site (www.panasonic.ca), or an authorized

2. Servicentre nearest you.

Stereo headphones . . . . . . . . . . . . . . . . . . . . . . . . 1

(RFEV716P-KS)

Wired remote control . . . . . . . . . . . . . . . . . . . . . . . 1

(N2QCBD000010)

Beltclip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

(RYQ0350-K)

Use numbers indicated in parentheses when asking for replacement parts.

To order accessories contact 1-800-332-5368 or web site

(http://www.panasonic.com).

Panasonic Consumer Electronics Company, Division of

Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

http://www.panasonic.com

Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. (“PSC”)

Ave. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

c 2000 Matsushita Electric Industrial Co., Ltd.

This manual was printed with soy based ink.

RQT5849-P F1200KK0

Printed in Japan

Dear Customer

Thank you for purchasing this product.

For optimum performance and safety,

please read these instructions carefully.

Concerning Compact Discs

Only compact discs bearing this mark can be used with this unit.

However, continued use of irregular shaped CDs can damage the unit.

If the surface is dirty

Wipe it with a damp cloth and then wipe dry. Wipe from the center toward the outer

circumference.

How to hold a disc

How to store the disc in its

case

How to remove a disc from its

case

Play surface

(shiny surface)

Label side up

Handling precautions

≥If you are taking the CD from a cold to

a warm environment, moisture may

form on the CD. Wipe this off with a

soft, dry, lint-free cloth before using the

CD.

≥Do not write on the label side with a

ball-point pen or other writing instru-

ment.

≥Do not use record cleaning sprays,

benzine, thinner, static electricity pre-

vention liquids or any other solvent.

≥Do not attach labels or stickers to CDs.

(Do not use CDs with exposed adhe-

sive from tape or left over peeled off

stickers.)

≥Do not use scratch-proof protectors

etc.

Storage precautions

Be sure to store CDs in their cases to

protect them from dust, scratches, and

warping.

Do not place or store CDs in the fol-

lowing places

≥Locations exposed to direct sunlight

≥Humid or dusty locations

≥Locations directly exposed to a heat

vent or heating appliance

≥In the glove compartment or on the

rear deck of an automobile

SL-SX285

Removing batteries

Push up on the battery in

the direction indicated by

the arrow. Then lift it out.

If the battery lid

comes loose

Slide the lid back into

place horizontally.

Power Supply Preparations

Refer to the speciﬁcations (page 8) for information on operating times when using rechargeable batteries or dry-cell batteries.

Using the AC adaptor

(not included)

Be sure to obtain the optional AC adaptor.

Optional AC adaptor: RP-AC46

Connect the AC adaptor.

Conserving power

To save power when the unit is not to be used for a long

time, unplug the AC adaptor from the household AC

outlet. Reprogram tracks if necessary before use.

Note!

≥Turn the unit off before connecting or disconnecting

the AC adaptor.

Using rechargeable batteries

(not included)

Obtain the optional rechargeable batteries.

Make sure to recharge the batteries before using them.

The unit cannot be used to charge rechargeable batter-

ies other than those specially designed for it.

Optional batteries : P-3GAVA/2B

Recharging procedure

Insert the special rechargeable bat-

teries into the unit.

2 Connect the AC adaptor.

(Refer to “Using the AC adaptor” for connection

instructions.) Recharging starts and the “H

”

charging indicator ﬂashes on the unit’s display.

When the rechargeable batteries fully recharge the

charging indicator disappears.

3 When recharging is complete, un-

plug the AC adaptor from the house-

hold AC outlet and the DC IN jack.

Note!

≥Rechargeable batteries have a service life of approxi-

mately 300 charge-discharge cycles. The batteries

have reached the end of their operational life if they

last for a noticeably shorter time after recharging, or if

they cannot be recharged at all. Replace the batteries.

≥Recharging may only be performed when the unit is

powered off.

≥The AC adaptor and rechargeable batteries may be-

come warm while recharging is in progress. This is not

a malfunction.

≥Leaving the AC adaptor connected can cause the bat-

teries to go ﬂat. After recharging the batteries, discon-

necting the AC adaptor from the AC power outlet, en-

sure you disconnect the adaptor from the unit’s [DC IN

4.5 V K] terminal.

Battery indicator

This indicator ﬂashes when the batteries are almost out

of power. Power is cut off completely a short while later.

Rechargeable batteries: Recharge batteries.

Dry cell batteries: Replace batteries with new ones.

Note!

≥The length of time the unit will continue to operate be-

tween when the battery indicator starts ﬂashing and

when the power is cut off differs depending on the

type of batteries used.

≥The battery indicator may not ﬂash if rechargeable

batteries other than those designated by Panasonic

are used.

Using the car adaptor

(not included)

Be sure to obtain the car adaptor (SH-CDC9) available

as an optional accessory.

The car adaptor can be used to recharge the unit’s bat-

teries while in the car.

If the unit malfunctions or freezes during use,

disconnect the power sources (the AC adaptor

and batteries).

Re-connect the power source and continue op-

eration.

CAUTION:

Use only car adaptor, Model: SH-CDC9 manufac-

tured by Matsushita Electric Industrial Co.,Ltd.

DC IN jack (DC IN 4.5 V K)

Back panel of the unit

Household

AC outlet

AC adaptor

S-XBSTRAINTRAIN

ALL

RANDOM

SORRY

Battery indicator

Using dry cell batteries

(not included)

After disconnecting the AC adaptor, insert two “AA”

(LR6) alkaline batteries.

The procedure for inserting and removing dry cell bat-

teries is identical to that for rechargeable batteries.

Note!

≥The dry cell batteries should be changed when the

unit is off.

Before operating the buttons

Be sure to move [HOLD] to release

the unit from the HOLD mode.

This function causes the unit to ignore

short, accidental button presses. (The

disc lid can still be opened and closed.)

The HOLD function prevents the

following:

≥The unit is powered on accidentally

when not in use, causing the batteries

to run down.

≥A button is accidentally pressed during

play, interrupting the operation.

To use the HOLD function

Set [HOLD] to the HOLD position.

The unit and wired remote control have

HOLD functions, each of which works in-

dependently.

“(” indication

When the main unit is in HOLD mode,

pressing any button causes the indica-

tion “(” to appear on the display.

When the unit is powered off

The “(” indication appears only

when [

] (main unit) is pressed.

HOLD

HOLD mode

HOLD Function

≥Never mix dry cell and rechargeable batteries.

≥Turn the unit off before replacing the recharge-

able batteries.

Button Display/referenceOperation

To pause play

To stop play

To turn off the

unit

Skip forward/

backward

(skip function)

Rapid forward/

backward

(search function)

Off mode

Stop mode

Sequential Play

Basic Play

Follow steps 1–5.

In step 2: Connect the stereo headphones and wired remote control to the headphone jack [Ë]. (Plug in ﬁrmly.)

In step 5: The volume range is 0-25. Press and hold to change the volume successively. The volume changes when

pressed while the level is displayed. If any other display is shown, it changes to show the current level.

(The volume returns to 10 when you disconnect the power source.)

≥Play stops automatically when all the tracks have been played.

≥If the unit has been connected to the car audio system, set this unit’s volume to 10, then adjust the volume level on

the system.

Resume function

The player stores the track where you stopped play and

if you press [1

;

] (main unit) or [∫/1] (remote control),

play resumes from the beginning of the track.

The resume function is canceled (play starts from the

ﬁrst track) if you open the lid when the unit is in stop

mode. It is also usually canceled when you replace the

CD while the unit is off.

Note!

≥The resume function may work if you replace the CD

while the unit is off.

≥If you turned the unit off near the end of the track, play

may resume from the beginning of the next track.

≥The resume function works automatically and cannot

be turned off.

Removing discs

1 Press [∫,OPR OFF] to stop play and disc

rotation.

2 Slide [OPEN 1] to open the lid.

3 Press [PUSH] to release the disc.

Do not stop the disc by hand or try to remove it before it

stops rotating. This can damage CDs.

Note!

Never insert foreign objects into the unit.

Auto power off function

If the unit is left in stop mode for approximately 10 min-

utes, the unit powers itself off automatically in order to

prevent the battery from running down.

(If no disc is loaded in the unit, it powers itself off in

about 30 seconds.)

≥During program play (page 4), these buttons are

used to skip forward or backward through the

programmed sequence of tracks.

≥You cannot skip to tracks that have been played

in random or random repeat play (page 4).

≥During program play, 1-track repeat play, random

play and random repeat play (page 4), search op-

eration is limited to the current track only.

Press during play.

Press during stop mode.

Press during play.

(Press [:] twice to skip to the

beginning of the previous tracks.)

Press again to restart play.

Press and hold during play.

OPEN

HOLD

VOL

S-XBS

VOL

TRAIN

ALL

RANDOM

SORRY

S-XBS

VOL

TRAIN

ALL

RANDOM

SORRY

Label must face upward.

Track number in play

Elapsed playing time of each track

Backward

Forward

S-XBS

VOL

TRAIN

ALL

S-XBS

VOL

TRAIN

ALL

S-XBS

VOL

TRAIN

ALL

RANDOM

Total number of tracks

Total playing time

Plug type:

3.5 mm (1/8 in.) stereo

For your reference:

“” indication

This indication appears for about 30 seconds if [1;] (main unit) or [∫/1] (remote control) is pressed when no disc

is loaded in the unit or if the disc is not properly secured.

“*” indication

This indication appears for about 10 minutes when the lid is opened. (However, the indication does not appear when

the unit is powered off.)

Increase

Decrease

Note on CD-R and CD-RW

This unit can play CD-DA format audio CD-R and

CD-RW that have been ﬁnalized

upon completion

of recording. It may not be able to play some CD-R

or CD-RW due to the condition of the recording.

Finalizing is a process that enables CD-R/CD-RW players

to play audio CD-R and CD-RW.

Close the lid

Other Play Methods

The letters such as A in the various illustrations refer to the descriptions in the “Location of Controls” section (see below).

This system deals with skipping in a variety

of ways:

≥An anti-skip mechanism prevents skipping caused

when play speed changes due to swinging of the unit.

≥A recovery system immediately returns the laser pick-

up to its original position if it is knocked off the track by

a strong shock.

≥The 40-second anti-skip memory ﬁlls in interruptions

caused by bumps and vibrations.

The anti-skip system works automatically while the

system is on and cannot be canceled.

When bumps continue repeatedly

The message “SORRY” appears on the display and

sound is interrupted.

Note!

The anti-skip memory compresses digital signals.

Anti-Skip System

S-XBS

VOL

TRAIN

ALL

RANDOM

SORRY

Skip play

The disc plays from the speciﬁed track through to the

end, then play stops automatically.

Preparation: Put unit in stop mode.

1 Select the desired track.

Program play

Up to 24 tracks can be entered in the programmed se-

quence.

Preparation: Put unit in stop mode.

1 Select the desired track.

2 Register in sequence.

(The indication “M” and the programmed se-

quence appear on the display.)

3 Repeat steps 1 and 2 to program all

the desired tracks.

VOL

∫ To program the same track in the se-

quence more than once

∫ After step 2, press [MEMORY/RECALL] the desired

number of times.

∫ If “'” is displayed

∫ No more tracks can be programmed.

∫ To conﬁrm the contents of the program

∫ Press [MEMORY/RECALL] while the disc is playing.

(The number of the programmed tracks appear on

the display in sequence.)

∫ To delete the entire programmed se-

quence

∫ Press [∫,OPR OFF].

Note!

The repeat and random play modes are canceled after

steps 1 and 2.

Repeat play/Random play

Press during play or stop mode.

The setting is switched in the sequence indicated below

each time [MODE] is pressed.

1-track repeat (1 `)(----------------]

One track is repeated. |

All-track repeat (`) |

All the tracks on the disc are repeated. |

Random (RANDOM) |

The tracks play once each in random |

order and then play stops. |

v |

Random repeat (RANDOM, `) |

The tracks play repeatedly in random |

order. |

Cancel (no indicator is shown)

--------------}

When pressed during program play

The setting is switched in the sequence indicated below

each time [MODE] is pressed.

1-track repeat (1

M)(------------]

One track is repeated. |

Memory repeat (

M) |

The programmed tracks are repeated. |

Cancel (

M) -------------------------------------------}

Note!

≥You can select the ﬁrst track to play in random play

and random repeat play by pressing [9] while the

disc is stopped. All the tracks are played.

≥You cannot select random play or random repeat play

during program play.

≥The mode is canceled when you disconnect the power

source.

MODE

Changing the sound quality

Press during play or stop mode.

The setting switches in the sequence indicated below

each time [EQ] is pressed.

S-XBS>TRAIN>Cancel (no indicator is shown)

^==========b

S-XBS:

Select this setting to boost the low-range response.

TRAIN:

Select this setting to avoid annoying other passengers

with noise from your headphones while riding on the

train, or to reduce fatigue when listening for a long peri-

od of time.

Note!

The setting returns to S-XBS when you disconnect the

power source.

Location of Controls

Portable CD Player A

A Display

B Memory/recall button

(MEMORY/RECALL)

C Headphone volume control

buttons (VOL i,j)

D EQ button (EQ)

E Mode button (MODE)

F Play/pause button (1;)

G Skip/search buttons

(:, 96, 5)

H Stop/operation off button

(∫,OPR OFF)

I Hold switch (HOLD)

J Headphone jack (Ë)

K CD release button (PUSH)

L Open switch (OPEN 1)

M Hole for car mounting base

/beltclip

N DC IN jack

(DC IN 4.5 V K)

Wired remote control B

A Skip/search buttons

(:, 9)

B Play/stop/operation off button

(∫/1)

C Volume control buttons

(j,VOL,i)

D Earphone jack

E Clip

F Hold switch (HOLD)

G EQ button (EQ)

H Plug

Back panel of

the unit

B C

KJL

VOL

Main unit

Remote control

Beep

Using the Unit with Optional Accessories

Headphone jack(Ë)

Other equipment

(White)

(Red)

Stereo connection

cable

(not included)

RQT5849

1Remove the screw from

the bracket at the rear

of the car mounting

base.

Replace the screw in the

lower hole of the bracket.

Bracket

Screwdriver

Using the Wired Remote Control

To start play

To stop play

To turn off

the unit

The remote control can be operated regardless of the

HOLD mode of the unit.

Preparation:

Release the remote control from the HOLD mode.

∫ Operation conﬁrmation tones

» When an operation button is pressed, a conﬁrmation

tone sounds. Refer to the parentheses in the illustra-

tion for the different types of conﬁrmation tones.

Basic operation

Skipping

tracks

Searching

through tracks

To adjust the

volume

Press once during off or stop mode.

Press once during play.

Press and hold during play or stop

mode.

HOLD

(Beep)

(Beep...Beep)

(Beep...Bee...p)

Other operations

To change sound quality

See page 4.

Press during play.

(Press [:] twice to skip to the beginning of

the previous tracks.)

Press and hold during play.

VOL

Forward

(Beep Beep)

Backward

(Beep Beep Beep)

≥The volume range is 0–25. (Press and hold

to change the volume successively.)

≥A tone (beep-beep) sounds when you

reach the minimum or maximum volume.

Decrease

(Beep)

Increase

(Beep)

Using the unit with an audio systemUsing the unit with a car audio

system

Items to be purchased

For connection to the car audio system

Car stereo cassette adaptor (SH-CDM10A)

Connect the car stereo cassette adaptor to the

unit’s headphone jack.

(When doing this, set this unit’s volume to 10.)

For securing the unit and connecting the power

supply:

≥Car adaptor (SH-CDC9)

≥Car mounting kit (SH-CDF20)

Note when using the car mounting kit (SH-CDF20)

Note!

≥When you switch off the car, volume and sound quality

may return to the original settings and the resume

function may work even if you change the disc.

≥It may not be possible to use the unit with some types

of car stereos owing to restrictions imposed by the

construction of the car stereo cassette adaptor.

For further details, refer to the instructions of the part

concerned.

For your reference:

≥Obtain the optional connecting cable if the other equip-

ment comes with mini-phone jacks.

≥If you connect speakers (active or otherwise) directly to

the unit's headphone jack, ensure they have an imped-

ance of 1 k≠ or less.

Note!

Do not connect the cable to the PHONO terminals on

an ampliﬁer.

Turn off this unit and the other equipment before operation.

1 Connect the remote control to the unit's

headphone jack.

2 Connect the stereo connection cable to

the remote control's headphone jack and

the terminals on the other unit.

The unit may malfunction if you connect this cable

directly to the unit.

3 Set the volume to 10.

Make further volume adjustments with the other

unit.

4 Control play with the buttons on the main

unit.

The tone will be heard if you use the buttons on the

remote control.

CD or AUX

Wired remote control

Limited Warranty

Panasonic Consumer Electronics Company or Panasonic

Sales Company (collectively referred to as “The warrantor”) will

repair or replace this product with new or refurbished equivalent

product, free of charge, in the U.S.A. or Puerto Rico from the

date of original purchase in the event of a defect in materials or

workmanship as follows:

For one (1) year—Radio, Clock Radio, Radio with Tape

Player or Recorder, Speaker

For ten (10) days—Batteries—(when applicable)—New re-

chargeable batteries in exchange for defective rechargeable

batteries. Non-rechargeable batteries are not warranted.

For ninety (90) days—SD Memory Card—New SD card of the

same memory capacity in exchange for a defective SD Card for

ninety (90) days.

For assistance in the U.S.A. in obtaining service contact:

Panasonic Services Company

Panasonic PLUS Department

20421 84th Avenue South

Kent, WA 98032

Phone: 1-800-833-9626

FAX: 1-800-237-9080

If service is needed during the warranty period the purchaser

will be required to furnish a sales receipt/proof of purchase indi-

cating date of purchase.

Also, the purchaser will be responsible for shipping the unit to

the above address. This warranty is extended only to the origi-

nal purchaser.

For assistance in Puerto Rico contact, Panasonic Sales

Company at the address or telephone number above.

This warranty only covers failures due to defects in materials

or workmanship which occur during normal use and does not

cover damage which occurs in shipment or failures which are

caused by products not supplied by the warrantor or failures

which result from accident, misuse, abuse, neglect, mishan-

dling, misapplication, faulty installation, set-up adjustments, im-

proper maintenance, alteration, improper antenna, inadequate

signal pick-up, maladjustment of consumer controls, modiﬁca-

tion, line power surge, or commercial use of the product, or

damage that is attributable to acts of God, or service by anyone

other than a PASC Factory Servicenter.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDEN-

TAL OR CONSEQUENTIAL DAMAGES RESULTING FROM

THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY, INCLUDING WITHOUT LIMI-

TATION, DAMAGE TO TAPES, RECORDS OR DISCS. ALL

EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE

WARRANTIES OF MERCHANTABILITY, ARE LIMITED TO

THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental

or consequential damages, or limitations on how long an implied

warranty lasts, so the above exclusions or limitations may not

apply to you.

This warranty gives you speciﬁc legal rights and you may also

have other rights which vary from state to state.

If a problem with this product develops during or after the war-

ranty period, you may contact your dealer or Panasonic PLUS

Department. If the problem is not handled to your satisfaction,

then write to the Consumer Affairs Department at the company

address indicated above.

Panasonic Consumer Electronics

Company, Division of Matsushita

Electric Corporation of America

One Panasonic Way,

Secaucus, New Jersey 07094

Panasonic Sales Company, Division

of Matsushita Electric

of Puerto Rico, Inc. (“PSC”)

Ave. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

Tel. (787) 750-4300

FAX. (787) 768-2910

If you ship the product

Carefully pack and send it prepaid, adequately insured and preferably in the original carton.

Attach a letter, detailing the complaint, to the outside of the carton.

Do NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to

make repairs.

Customer’s Record

Model Dealer’s

No. Name

Serial

No.

Code Dealer’s

No. Address

Date

Purchase

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PROD-

UCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN,

SPLASHING, DRIPPING OR MOISTURE.

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

The product you have purchased is powered by a nickel-cadmium bat-

tery which is recyclable. Please call 1-800-8-BATTERY for information

on how to recycle this battery.

CAUTION:

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful inter-

ference in a residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

≥Reorient or relocate the receiving antenna.

≥Increase the separation between the equipment and receiver.

≥Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

≥Consult the dealer or an experienced radio/TV technician for help.

Any unauthorized changes or modiﬁcations to this equipment would void the

user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Ni-Cd

RBRC

Attaching the Beltclip

Attach the included beltclip to make it easier to carry while jogging.

1 Insert the ﬂange on the belt-

clip into the slot on the base

of the unit.

2 Press the beltclip ﬁrmly

against the base.

3 Fit the screw into the hole in

the unit.

4 Screw in the direction indi-

cated.

5 Clip on to your belt.

Beltclip

Maintaining the Lens

Open the lid and clean the lens as

shown in the ﬁgure.

Use a cotton swab to gently wipe

off any ﬁnger-prints.

Panasonic SLSX285 Operating instructions

Panasonic SLSX285 Operating instructions

Panasonic SLSX285 Operating instructions

Related papers

Other documents