www.whirlpool.eu/register
Instructions for use
EN
Quick Guide
THANK YOU FOR PURCHASING A BAUKNECHT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.bauknecht.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set cycle 7 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 8 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
DETERGENT DISPENSER DRAWER
Compartment 1: Prewash detergent (powder)
Compartment 2: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 3: Additives (fabric softeners,
etc.)
The fabric softener must not exceed the “MAX” level.
1
2
3
A
B
1. ON/OFF button
2. CHILD LOCK button
3. CLEANING ACTION button
4. CLEANING ACTION indicator lights
5. START/PAUSE button and indicator light
6. OPTION button and indicator light
7. DELAY START button
8. SPIN button
9. TEMPERATURE button
10. WASH CYCLE SELECTOR KNOB
1
10
2
DISPLAY
4
5
6
7
8
9
3
Maximum load 8 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and Additives
Recommended
detergent
Residual
dampness %
Energy con-
sumption kWh
Total water l
Wash cycle
Temperature
Maximum
spin
(r.p.m.)
Maximum
load (kg)
Duration
(minutes)
Prewash Wash
Fabric
softener
Powder Liquid
Default Range
1 2 3
1 Anti-Stain 100 40 °C
- 40 °C 1400 8,0 **
– – – –
2 Anti-Stain 45‘ 40 °C
- 40 °C 1200 4,5 ** –
–
– – –
3 Whites 60 °C
- 90 °C 1400 8,0 **
– – – –
4 Bed&Bath 60 °C
- 60 °C 1400 8,0 **
– – – –
5
Eco cotton
60°/40°
(1)
60 °C
60° C 1400 8,0 225 –
53 1,04 55
40°C 1400 8,0 220 –
53 1,03 92
6 Mixed 40 °C
- 40 °C 1000 4,5 ** –
–
– – –
7 Cotton (2) 40 °C
- 60 °C 1400 8,0 220 –
– 53 1,03 92
8 Synthetics (3) 40 °C
- 60 °C 1200 4,5 200
– 32 0,80 78
9 Colours 40 °C
- 40 °C 1400 8,0 **
– – – –
10 Rapid 30' 30 °C
- 30 °C 800 4,5 30 –
–
71 0,19 44
11 Wool 40 °C
- 40 °C 800 2 ** –
–
– – –
12 Darks 30 °C
- 30 °C 800 4,5 ** –
–
– – –
13 Ultra-delicate 30 °C
- 30 °C
--
1,0 ** –
–
– – –
14 Duvets 30 °C
- 30 °C 1000 3,5 ** –
–
– – –
Rinse – – 1400 8,0 ** – –
– – – – –
Spin & Drain * – – 1400 8,0 ** – – – – – – – –
Required dosage Optional dosage
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Anti-Stain 100
This cycle is suitable to heavily-soiled garments with resistant colours. It
ensures a washing class that is higher than the standard class (A class).
When running the programme, do not mix garments of dierent colours.
We recommend the use of powder detergent. Pre-treatment with special
additives is recommended if there are obstinate stains
Anti-Stain 45’
This cycle is ideal for washing daily stains in 45’. It is ideal for mixed fabrics
and coloured garments.
Whites
For heavily soiled whites and resistant colours.
Bed&Bath
For washing home linen in a single cycle. It optimises the use of fabric
softener and allows for saving time and electricity. We recommend the
use of powder detergent.
Eco cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
ecient in terms of combined water and electricity consumption.
Mixed
To wash mixed and coloured items together.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic bres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton bres.
Colours
For washing coloured cotton garments. This programme is optimised to
keep colours bright even after repeated washing.
Rapid 30’
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Wool - Woolmark Apparel Care - Green:
The “Wool” wash cycle is approved by the Woolmark Company for
washing wool garments classied as “hand-washable”,
provided that the wash complies with the instructions
appearing on the garment’s label and with those
provided by the manufacturer of this washing machine.
(M1127)
Darks
For washing dark-coloured garments. The wash cycle is designed to
preserve dark colours over time.
We recommend using a liquid detergent for best results, preferably when
washing dark-coloured garments.
Ultra-delicate
For washing very delicate garments. It is advisable to turn the garments
inside out before washing them. For best results, use liquid detergent on
delicate garments.
Duvets
To wash double or single duvets (weighing under 3,5 kg), cushions or
down jackets. Duvets should be loaded into the drum with their edges
folded inwards and no more than ¾ of the total drum volume should be
used up. For best results, it is advisable to use liquid detergent to be
poured into the detergent drawer.
Rinse
Designed for rinsing and spinning.
Spin & Drain
Designed for spinning and draining the water.
DISPLAY
The display is useful when programming the washing machine and
provides plenty of information.
The duration of the available wash cycles and the remaining time of a
running cycle appear (the display will show the maximum duration of the
cycle chosen, which may decrease after several minutes, since the
eective duration of the programme varies depending on the wash load
and the settings chosen); if the DELAY START option has been set, the
countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin
speed and temperature values attained by the machine during the set
wash cycle, or the values selected most recently, if these are compatible
with the set wash cycle.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; the indicator light relative to START/PAUSE
will ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- The machine automatically displays the maximum temperature and spin
speed values for the selected cycle, or the most recently used settings if
they are compatible with the selected cycle. Pressing the button
gradually reduces the temperature down to the cold wash “OFF” setting.
Pressing the button gradually reduces the spin speed until it is
completely excluded (“OFF” setting). Pressing the buttons further restores
the maximum allowed values for the selected cycle.
- Select the desired option.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock (
symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. To start the wash cycle from the point at
which it was interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE button (the relative indicator light will ash
amber), then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
AT THE END OF THE WASH CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press ON/OFF
button, the washing machine will switch o automatically after about a
half of an hour.
OPTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
Prewash
Allows you to perform a prewash.
Delay start
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period is reached. When this
option has been activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until “OFF” appears on
the display.
Temperature
Each wash cycle has a pre-dened temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-dened spin speed. To modify the spin speed,
press the button. The value will appear on the display.
Cleaning Action
Option makes it possible to optimise washing based on the level of
soil in the fabrics and on desired wash cycle intensity.
For heavily-soiled garments press button until the “Intensiv” level
is reached. This level ensures a high-performance wash due to a larger
quantity of water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the most stubborn
stains.
For lightly-soiled garments or a more delicate treatment of the fabrics,
press button until the “Sanft” level is reached. The cycle will reduce
drum rotation to ensure washing results that are perfect for delicate
garments.
CHILD LOCK
To activate the control panel lock, press and hold the button for
approximately 2 seconds. When the symbol is lit, the control panel is
locked (except for the ON/OFF button). This will prevent accidental
modications to wash cycles, especially when children are at home. To
deactivate the control panel lock, press and hold the button for
approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed bres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
o and disconnect it from the mains power. Do not use ammable liquids to
clean the washing machine.
Cutting o the water and electricity supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washing machine has a “Auto-Clean” cycle for its internal parts; it
must be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specied for lightly soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning cycle every 40
wash cycles.
To start the programme press button A for 5 seconds.
The cycle will start automatically and
will run for about 70 minutes. To stop
the cycle, press the START/PAUSE
button.
Cleaning the detergent dispenser drawer
Remove the dispenser drawer by lifting and pulling it outwards. Wash it
under running water; this procedure should be eected regularly.
Caring for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
Cleaning the pump
The washing machine is tted with a self-cleaning pump that does not
require any maintenance. Small items (such as coins or buttons) may
sometimes fall into the protective pre-chamber situated at the base of the
pump.
! Make sure that the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the covering panel on the front side of the machine by
inserting a screwdriver in the centre and sides of the panel and using it as
a lever;
2. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
3. clean the inside thoroughly;
4. screw the cover back on;
5. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washing machine model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washing machine to save space and facilitate loading and unloading
of the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the lling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Installation instructions”.
A
1
2
TROUBLESHOOTING
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The wash cycle does not start.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The washing machine does
not ll with water (“H2O”
appears on the display).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine
continuously loads and
unloads water.
The drain hose is not tted between 65 and 100 cm from the oor.
The free end of the hose is immersed in water.
The wall drainage system is not tted with a breather pipe.
If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the
Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems relating
to back-siphonage, causing the washing machine to ll with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The washing machine does
not drain or spin.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The washing machine leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” and START/
PAUSE indicator lights
ash rapidly and the display
visualises an error code (e.g.:
F-01, F-...).
Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and
machine wash”, or the like).
Too much detergent was used.
DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold “Start/Pause” button, within 5 seconds press also
“ON/OFF” button and hold both buttons for 2 seconds.
Before using the appliance, read these safety instruc-
tions. Keep them nearby for future reference. These
instructions and the appliance itself provide impor-
tant safety warnings, to be observed at all times. The
manufacturer declines any liability for failure to ob-
serve these safety instructions, for inappropriate use
of the appliance or incorrect setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8years)
should be kept away from the appliance unless
continuously supervised. Children from 8years old
and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge can use this appliance only if they
are supervised or have been given instructions on
safe use and understand the hazards involved.
Children must not play with the appliance. Cleaning
and user maintenance must not be carried out by
children without supervision. Never open the door
forcibly or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching device,
such as a timer, or separate remote controlled
system.
This appliance is intended to be used in
household and similar applications such as: sta
kitchen areas in shops, oces and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the
programme table.
This appliance is not for professional use. Do not
use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents, scouring
powder, glass or general purpose cleaners, or
ammable uids; do not machine wash fabrics that
have been treated with solvents or ammable
liquids.
INSTALLATION
The appliance must be handled and installed by
two or more persons- risk of injury. Use protective
gloves to unpack and install- risk of cuts.
If you want to stack a dryer on top of your washing
machine, rst contact our After-Sales Service or
your specialist dealer to verify whether this is
possible. This is only possible if the dryer is attached
to the washing machine by means of appropriate
stacking kit available through our After- Sales
Service or your specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualied technician. Do not repair or
replace any part of the appliance unless specically
stated in the user manual. Keep children away from
the installation site. After unpacking the appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest After-sales Service. Once
installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children- risk of
suocation. The appliance must be disconnected
from the power supply before any installation
operation- risk of electric shock. During installation,
make sure the appliance does not damage the
power cable - risk of re or electric shock. Only
activate the appliance when the installation has
been completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
the four feet are stable and resting on the oor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“oating” oors (certain parquet and laminate
materials), secure a 60x60x3cm (at least) sheet of
plywood to the oor then place the appliance on
top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold ll only models: do not connect to the
hot water supply.
For models with hot ll: the hot water inlet
temperature must not exceed 60°C.
The washing machine is tted with transport
bolts to prevent any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
After their removal, cover the openings with the 4
enclosed plastic caps.
After installation of the device, wait a few hours
before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on your
model) are not obstructed by a carpet or other
material.
Use only new hoses to connect the appliance to
the water supply. The old hose-sets should not be
reused.
The supply water pressure must be in the 01-1
Mpa range.
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVE
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly, or
if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the manufacturer,
its service agent or similarly qualied persons in
order to avoid a hazard - risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched
o and disconnected from the power supply
before performing any maintenance operation;
never use steam cleaning equipment - risk of
electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of
household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
1.
2.
3.
4. 5.
150 ml
100 ml
50 ml
10 mm - 0,39 inch
2 cm - 0,7 inch
6.
7.
1.
2.
3.
4. 5.
150 ml
100 ml
50 ml
10 mm - 0,39 inch
2 cm - 0,7 inch
6.
7.
195157289.00
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Whirlpool FWL 8F4 User guide
- Category
- Washing machines
- Type
- User guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Bauknecht WA Soft 8F42PS Setup and user guide
-
-
-
-
Bauknecht Super Eco 8418 Owner's manual
-
-
Hotpoint H6 W845WB UK Daily Reference Guide
-
-
Hotpoint BI WMHG 81484 UK Setup and user guide
-
Bauknecht HWM 8F4 Owner's manual