Everbilt EBPBV Installation guide

Everbilt
Brand
Everbilt
Model
EBPBV
Type
Installation guide

Everbilt EBPBV is a vertical float switch designed to automatically turn on and off a pump based on water level. It is commonly used in sump pumps, sewage pumps, and other applications where automatic water level control is required. The switch is made of durable materials and is designed for long-lasting performance. It is easy to install and comes with all the necessary hardware.

Here are some of the key features and benefits of the Everbilt EBPBV vertical float switch:

  • Automatically turns on and off a pump based on water level
  • Durable construction for long-lasting performance
  • Easy to install with all necessary hardware included

Everbilt EBPBV is a vertical float switch designed to automatically turn on and off a pump based on water level. It is commonly used in sump pumps, sewage pumps, and other applications where automatic water level control is required. The switch is made of durable materials and is designed for long-lasting performance. It is easy to install and comes with all the necessary hardware.

Here are some of the key features and benefits of the Everbilt EBPBV vertical float switch:

  • Automatically turns on and off a pump based on water level
  • Durable construction for long-lasting performance
  • Easy to install with all necessary hardware included
HOMEDEPOT.com
Please contact 1-844-251-7446 for further assistance.
SKU #1001-098-868
Model #EBPBV
Assembly
1
ATTACHING THE MOUNTING
BRACKET
□ Place the mounting bracket (B) over the
oat switch (A). Thread the two screws
(C) into the oat switch (A) to attach the
bracket (B). DO NOT OVERTIGHTEN.
C
A
B
C
2
ATTACHING THE ROD
□ Insert the rod (G) into the oat switch
(A). Slide the rod stop pin (E) into the
oat switch (A) to keep the rod from
falling out of the oat during operation.
E
G
A
3
ATTACH THE FLOAT
□ Slide the oat bulb (D) over the rod (G)
with the narrow side facing up. Install
the oat stop (F) on the rod (G).
D
G
F
Installation
1
ATTACHING THE SWITCH
□ Loosen the clamp (H) completely with a
screwdriver.
□ Attach the mounting bracket (B) and switch
(A) to the discharge pipe by inserting the
clamp (H) through the mounting bracket’s (B)
slots. Keep the vertical switch vertical.
□ The bottom of the oat ball must be at least 1/2
in. above the outlet of the pump.
H
H
B
A
D
2
SECURING THE SWITCH
□ Tie the power cords of the pump and
vertical switch to the discharge pipe
with the cable tie (I) or elecctrical
tape (not included).
I
3
TESTING THE SWITCH
□ Plug the pump power cord into the piggyback switch
plug. Then plug the piggyback switch cord into the
GFCI outlet.
□ Check the pump and vertical switch by lling the
sump pit with water and observe the operation of
the pump and vertical switch through one complete
cycle.
□ Make sure the pump cannot move in the sump and
vertical switch moves freely up and down.
Safety Information
Failure to follow these precautions could result in serious injury or
death. Replace product immediately if switch cable becomes damaged
or severed. Keep these instructions with warranty after installation. This
product must be installed in accordance with National Electric Code,
ANSI/NFPA 70 so as to prevent moisture from entering or accumulating
within boxes, conduit bodies, ttings, oat housing, or cable.
Do not handle pump or vertical switch with wet hands or when standing
on wet or damp surface, or in water.
WARNING: EXPLOSION OR FIRE HAZARD. Do not use this product with
ammable liquids. Do not install in hazardous locations as dened by National
Electrical Code, ANSI/NFPA 70.
WARNING: ELECTRICAL SHOCK HAZARD. Disconnect power before installing
or servicing this product. A qualied service person must install and service this
product according to applicable electrical and plumbing codes.
TOOLS REQUIRED
Phillips screwdriver
PACKAGE CONTENTS
A Float switch F Float stop
I
B
D
H
C
A
F
E
G
B Mounting bracket G Rod
C Screw (x2) H Clamp
D Float bulb I Zip tie
E Rod stop pin
Assembly and Installation
Guide
Vertical Float Switch
  • Page 1 1

Everbilt EBPBV Installation guide

Everbilt
Brand
Everbilt
Model
EBPBV
Type
Installation guide

Everbilt EBPBV is a vertical float switch designed to automatically turn on and off a pump based on water level. It is commonly used in sump pumps, sewage pumps, and other applications where automatic water level control is required. The switch is made of durable materials and is designed for long-lasting performance. It is easy to install and comes with all the necessary hardware.

Here are some of the key features and benefits of the Everbilt EBPBV vertical float switch:

  • Automatically turns on and off a pump based on water level
  • Durable construction for long-lasting performance
  • Easy to install with all necessary hardware included
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents