Eurotech CTR-1462 Owner's manual

Eurotech
Brand
Eurotech
Model
CTR-1462
Type
Owner's manual

Eurotech CTR-1462 is a PC/104-Plus Single Slot PCMCIA/CARDBUS Interface Board. It provides a single ISA bus connector and a single PCI bus connector, allowing you to connect ISA and PCI devices to your PC/104-Plus system. The CTR-1462 also features a CARDBUS connector, which allows you to connect CARDBUS devices to your system.

Eurotech CTR-1462 is a PC/104-Plus Single Slot PCMCIA/CARDBUS Interface Board. It provides a single ISA bus connector and a single PCI bus connector, allowing you to connect ISA and PCI devices to your PC/104-Plus system. The CTR-1462 also features a CARDBUS connector, which allows you to connect CARDBUS devices to your system.

USER’S MANUAL
CTR-1462
PC/104-Plus Single Slot PCMCIA/CARDBUS Interface Board
Rev. 1.1 - November 2008 - ETH_CTR-1462_USM1.1
DIGITAL TECHNOLOGIES FOR A BETTER WORLD
www.eurotech.com
CTR-1462 – User’s Manual
Disclaimer
The information in this manual has been carefully checked and is believed to be accurate. Eurotech assumes no
responsibility for any infringements of patents or other rights of third parties, which may result from its use.
Eurotech assumes no responsibility for any inaccuracies that may be contained in this document. Eurotech makes no
commitment to update or keep current the information contained in this manual.
Eurotech reserves the right to make improvements to this document and/or product at any time and without notice.
Warranty
This product is supplied with a limited warranty. The product warranty covers failure of any Eurotech manufactured
product caused by manufacturing defects. Eurotech will make all reasonable effort to repair the product or replace it with
an equivalent alternative. Eurotech reserves the right to replace the returned product with an alternative variant or an
equivalent fit, form and functional product. Delivery charges will apply to all returned products.
Trademarks
All trademarks, both marked and not marked, appearing in this document are the property of their respective owners.
WEEE
The information below is issued in compliance with the regulations as set out in the 2002/96/CE directive, subsequently
superseded by 2003/108/CE. It refers electrical and electronic equipment and the waste management of such products.
When disposing of a device, including all of its components, subassemblies and materials that are an integral part of the
product, you should consider the WEEE directive.
This symbol has been attached to the equipment or, if this has not been possible, on the packaging,
instruction literature and/or the guarantee sheet. By using this symbol, it states that the device has been
marketed after August 13th 2005, and implies that you must separate all of its components when possible,
and dispose of them in accordance with local waste disposal legislations.
• Because of the substances present in the equipment, improper use or disposal of the refuse
can cause damage to human health and to the environment.
• With reference to WEEE, it is compulsory not dispose of the equipment with normal urban
refuse, arrangements should be instigated for separate collection and disposal.
• Contact your local waste collection body for more detailed recycling information.
• In case of illicit disposal, sanctions will be levied on transgressors.
RoHS
This device, including all it components, subassemblies and the consumable materials that are an integral part of the
product, has been manufactured in compliance with the European directive 2002/95/EC known as the RoHS directive
(Restrictions on the use of certain Hazardous Substances). This directive targets the reduction of certain hazardous
substances previously used in electrical and electronic equipment (EEE).
© 2008 Eurotech Spa
Eurotech S.p.A.
A member of the Eurotech Group
Via Fratelli Solari, 3/a
33020 - AMARO (UD)
ITALY
CTR-1462 – User’s Manual
Introduction
Conventions used within this Manual
The following conventions are used throughout this manual.
The “Mode” of the register:
Symbol / Text Definition
RW Readable and Writable register
RO Read only register
W Meaning of the register when written
R Meaning of the register when read
Hexadecimal numbering:
Hexadecimal numbers are indicated with an “h” suffix (for example: 11Ch)
Symbols and Text used in Pin-out tables:
Symbol / Text Definition
◄ Input
► Output
◄► Bi-Directional
▬ Passive
Module specific Dependent on module installed
NC Not Connected
Reserved Use reserved to Eurotech, must remain unconnected
# Active low signal
Warnings and Important Notices:
Within this manual you will find the following tables, please ensure that you read and understand these as
they are intended to highlight potential risks or precautions that should be taken.
Warnings:
Information to alert you to potential hazards:
Potential personal injury or damage to a system, device, or program.
Information and/or Notes:
Indicates important features or instructions that should be observed
3
CTR-1462 – User’s Manual
Technical Assistance
If you have any technical questions or if you cannot isolate a problem with your device, please e-mail the
Eurotech Technical Support Team: email: techsupp@eurotech.com
Before returning any Eurotech product, for any reason, you must e-mail the Eurotech Technical Support
Team on the above email address, giving the following information; you will then be sent an RMA number
(Returned Material Authorization) for the return of the material:
• Model number (see Figure 1)
• Serial number (see Figure 1)
• Detailed fault description
• Company Details
• Contact details
Transportation
When transporting the module for any reason it should be packed using anti-static material and placed in a
sturdy box with enough packing material to adequately cushion it.
Warning:
Any product returned to Eurotech that is damaged due to inappropriate packaging will
not be covered by the warranty!
Board labelling
On the external side of the ISA Bus connector, you will find several labels displaying the following:
• Batch Number
• Serial Number
• Model Number
• Hardware Revision
Model Number Hardware Revision
Serial Number
Batch Number
4
Figure 1. Board label locations
CTR-1462 – User’s Manual
Table of Contents
Introduction.......................................................................................................................................................3
Conventions used within this Manual.................................................................................................................3
The “Mode” of the register: ......................................................................................................................................3
Hexadecimal numbering: .........................................................................................................................................3
Symbols and Text used in Pin-out tables:................................................................................................................ 3
Warnings and Important Notices:............................................................................................................................. 3
Technical Assistance..........................................................................................................................................4
Transportation.....................................................................................................................................................4
Board labelling....................................................................................................................................................4
Table of Contents .............................................................................................................................................5
Chapter 1 Product Overview .......................................................................................................................6
Block Diagram ....................................................................................................................................................7
Product Definition ...............................................................................................................................................8
Electrical and Environmental Specifications.......................................................................................................9
Operating Characteristics ........................................................................................................................................9
Absolute Maximum Ratings .....................................................................................................................................9
MTBF (Mean Time Between Failures) ..................................................................................................................... 9
Chapter 2 Connector Description .............................................................................................................11
Connector Layout .............................................................................................................................................11
How to connect the CTR-1462 with other PC/104 & PC/104-Plus devices .....................................................12
J1 and J2: the ISA BUS.........................................................................................................................................12
J3: the PCI BUS....................................................................................................................................................14
The stack assembly............................................................................................................................................... 15
J5: PCI Slot Selection.......................................................................................................................................16
J20: CARDBUS connector ...............................................................................................................................17
Appendix .........................................................................................................................................................19
A.1. Mechanical Dimensions.........................................................................................................................19
A.2. Manual Revision History........................................................................................................................20
Eurotech Group Worldwide presence ..........................................................................................................21
5
CTR-1462 – User’s Manual
Chapter 1 Product Overview
The CTR-1462 is a single PC/104-Plus module based around the Ricoh 5C486 PCI-host controller, it
supports legacy 16-bit PC-CARD (PCMCIA) as well as 32-bit CARDBUS (expansion and memory cards), to
increase flexibility of the module it supports both ISA and PCI interrupts, also the module will also support
PCI-only architectures such as PCI-104.
The module can operate over wide temperature ranges, for example those commonly encountered in
automotive and mobile applications; also extensive use of SMD technology has been implemented to
increase reliability.
The CTR-1462 is a single +5V module (The +12V flash programming voltage is generated on-board).
In the following paragraphs you will find a brief description of the characteristics of the CTR-1462 board.
For a complete list of our products visit our website: www.eurotech.com
6
CTR-1462 – User’s Manual
Block Diagram
PCI Bus
7
PCI
CardBus Host
Controller
Power
Controller
PCI Slot
Selection
CardBus
Slot
ISA IRQ PCI Data PCI Control
+12V
ISA Bus
+5V
ISA IRQ
CTR-1462 – User’s Manual
Product Definition
General Features
• PC/104 Form Factor
• Low power consumption
• Single, locking and shielded 32-bit CARDBUS slot
• Supports type I, II and III cards
• Stacking PCI and ISA connectors
• Plug-and-Play automatic detection and configuration
• Can be configured to operate in any PCI-slot using DIP-switch
• Onboard +12V programming voltage generation
• High reliability, wide operating temperature range
CARDBUS PCI-host controller features
• Ricoh R5C486 Cardbus PCI host controller
• Compliant with 16-bit PCMCIA V2.1, JEIDA 4.2 and 32-bit PC-card 95/97/98, Card-32 specifications
• 16-bit legacy mode support
• Supports ACPI power management
Bus Interfaces
• 16-bit bus PC/104 bus connector and 32-bit PCI connector
• AT and PCI interrupts supported
• ISA bus for power and ISA interrupts only
• PCI interface +3.3V (+5V tolerant)
• PCI bus compliant with PCI bus specification 2.1 33MHz
• Compatible with PCI-104 systems
Operating Systems Supported
• Windows XPE, CE and Linux (no drivers needed)
RoHS:
• Fully RoHS (2002/95/CE) Compliant
• Fully RoHS (2002/95/CE) Compliant
8
CTR-1462 – User’s Manual
Electrical and Environmental Specifications
Operating Characteristics
Electrical Operating Characteristics
Power supply Nominal: 5.00V
Power consumption Typical: 70 mA (without any card)
Operating Temperature Range
For correct operation of the module, the ambient air temperature must remain within the following range:
Standard Minimum: -40 °C
Maximum: +85 °C
Absolute Maximum Ratings
Supply Voltage (Vcc) Minimum: 4.75V
Maximum: 5.25V
Storage Temperature Range Minimum: -40 °C
Maximum: +85 °C
Non-Condensing Relative Humidity <90%
Warning:
Stressing the module beyond the “Absolute Maximum Ratings” may cause permanent
damage. These are stress ratings only. Operation beyond the “Operating Conditions” is
not recommended. Extended exposure beyond the “Operating Conditions” may affect
device reliability
MTBF (Mean Time Between Failures)
Standard Temperature Hours
>166000 MIL STD 217 ground benign 25°C
9
(This page is intentionally left blank.)
CTR-1462 – User’s Manual
Chapter 2 Connector Description
Connector Layout
J3
J20
J1
J5
J2
Figure 2. Connector layout
Connector Function
J1 & J2 ISA BUS (PC/XT)
J3 PCI BUS
J20 CARDBUS slot
Table 1. Connector pinout
11
CTR-1462 – User’s Manual
How to connect the CTR-1462 with other PC/104 &
PC/104-Plus devices
J1 and J2: the ISA BUS
Connectors J1 and J2 contain the signals for the PC/AT ISA-bus. These signals match definitions of the
IEEE P996 standard. Below is shown a picture of the PC/104 ISA-bus connector.
KEY
J1
J2
KEY
Figure 3. ISA BUS layout
According to the PC/104 specifications, these connectors include KEY pins; these are filled holes in the
female side and missing pins on the male side of a connector, to avoid the wrong insertion in/of another
module.
Pin # J1A Used J1B Used
1 /IOCHK
2
GND
2
2 SD7
2
RESET
2
3 SD6
2
+5.0V
2
4 SD5
2
IRQ9
3
5 SD4
2
-5.0V
2
6 SD3
2
DRQ2
2
7 SD2
2
-12.0V
2
8 SD1
2
/SRDY
2
9 SD0
2
+12.0V
2
10 IOCHRDY
2
KEY
2
11 AEN
2
/SMEMW
2
12 SA19
2
/SMEMR
2
13 SA18
2
/IOW
2
14 SA17
2
/IOR
2
15 SA16
2
/DACK3
2
16 SA15
2
DRQ3
2
17 SA14
2
/DACK1
2
18 SA13
2
DRQ1
2
19 SA12
2
/REFRESH
2
20 SA11
2
BCLK
2
21 SA10
2
IRQ7
3
22 SA9
2
IRQ6
3
23 SA8
2
IRQ5
3
24 SA7
2
IRQ4
3
25 SA6
2
IRQ3
3
26 SA5
2
/DACK2
2
27 SA4
2
TC
2
28 SA3
2
BALE
2
29 SA2
2
+5.0V
2
30 SA1
2
OSC
2
31 SA0
2
GND
2
32 GND GND
2 2
Figure 4. J1 connector pinout
12
CTR-1462 – User’s Manual
Pin # J2A Used J2B Used
1 GND
2
GND
2
2 /MEMCS16
2
/SBHE
2
3 /IOCS16
2
LA23
2
4 IRQ10
3
LA22
2
5 IRQ11
3
LA21
2
6 IRQ12
3
LA20
2
7 IRQ15
3
LA19
2
8 IRQ14
3
LA18
2
9 /DACK0
2
LA17
2
10 DRQ0
2
/MEMR
2
11 /DACK5
2
/MEMW
2
12 DRQ5
2
SD8
2
13 /DACK6
2
SD9
2
14 DRQ6
2
SD10
2
15 /DACK7
2
SD11
2
16 DRQ7
2
SD12
2
17 +5.0V
2
SD13
2
18 /MASTER
2
SD14
2
19 GND SD15
2 2
Figure 5. J2 connector pinout
13
CTR-1462 – User’s Manual
J3: the PCI BUS
Connector J3 carries signals of the PCI Bus. The PCI Bus mechanical interface is a stackable 30x4 header.
This interface carries all of the required PCI signals per PCI Local Bus Specification Version. 2.1.
Figure 6. PCI BUS layout
Pin # A Used B Used C
J3
Used D Used
1 KEY
3
--
2
+5.0V
3
AD00
3
2 VIOPCI
3
AD02
3
AD01
3
+5.0V
3
3 AD05
3
GND
3
AD04
3
AD03
3
4 CBEO
3
AD07
3
GND
3
AD06
3
5 GND
3
AD09
3
AD08
3
GND
3
6 AD11
3
VIOPCI
3
AD10
3
GND
3
7 AD14
3
AD13
3
GND
3
AD12
3
8 +3.3V
2
CBE1
3
AD15
3
+3.3V
2
9 SERR
3
GND
3
--
2
PAR
3
10 GND
3
PERR
3
+3.3V
2
SDONE
3
11 STOP
3
+3.3V
2
--
2
GND
3
12 +3.3V
2
TRDY
3
GND
3
DEVSEL
3
13 FRAME
3
GND
3
IRDY
3
+3.3V
2
14 GND
3
AD16
3
+3.3V
2
CBE2
3
15 AD18
3
+3.3V
2
AD17
3
GND
3
16 AD21
3
AD20
3
GND
3
AD19
3
17 +3.3V
2
AD23
3
AD22
3
+3.3V
2
18 IDSEL0
3
GND
3
IDSEL1
3
IDSEL2
3
19 AD24
3
CBE3
3
VIOPCI
3
IDSEL3
3
20 GND
3
AD26
3
AD25
3
GND
3
21 AD29
3
+5.0V
3
AD28
3
AD27
3
22 +5.0V
3
AD30
3
GND
3
AD31
3
23 REQ0
3
GND
3
REQ1
3
VIOPCI
3
24 GND
3
REQ2
3
+5.0V
3
GNT0
3
25 GNT1
3
VIOPCI
3
GNT2
3
GND
3
26 +5.0V
3
CLK0
3
GND
3
CLK1
3
27 CLK2
3
+5.0V
3
CLK3
3
GND
3
28 GND
3
INTD
3
+5.0V
3
PCI_RST
3
29 +12.0V
2
INTA
3
INTB
3
INTC
3
30 -12.0V
2
KEY
3
-- GND
2 3
Figure 7. J3 connector pinout
Note:
For further information regarding the ISA and PCI bus, please visit the Eurotech
website (http://www.eurotech.com
), referring to the section titled “Industry Standards”.
14
CTR-1462 – User’s Manual
The stack assembly
The ISA and PCI bus connectors of the module are designed to allow it to be connected with other PC/104
and/or PC/104-Plus devices; we recommend users to follow this procedure to ensure that stacked modules
are not damaged.
Warning:
Appropriate ESD (Electro Static Discharge) precautions should be used for the following
procedure.
1. Turn off the power to the PC/104 (or PC/104-Plus) system or stack.
2. Select and install standoffs as required to correctly position the module on the PC/104 stack.
3. Remove the module from its anti-static bag.
4. Check that keying pins in the bus connector are correctly positioned.
5. Check the stacking order; make sure an XT bus card will not be placed between two AT bus cards or
it will interrupt the AT bus signals.
6. Hold the module by its edges and orient it so that the bus connector pins line up with the matching
connector on the stack.
7. Press the module evenly onto the PC/104 stack.
Figure 8 shows a typical module stack with two PC/104 modules, one PC/104 16-BIT module, and one
PC/104 8-BIT module.
The maximum number of modules is four in addition to the Host Board.
0.6 in. (15mm) Spacers (4 plcs.)
Stackthrough
8-bit module
0.435 in. (11 mm)
0.6 in. (15 mm)
Stackthrough
16-bit module
Stackthrough
PC/104Plus module
Non-Stackthrough
PC/104Plus module
0.6 in. (15mm) Spacers (4 plcs.)
0.6 in. (15mm) Spacers (4 plcs.)
0.100 in. (2.54 mm)
0.062 in. (1.57 mm)
Figure 8. The Module Stack
Warning:
Do not force the module onto the stack! Wiggling the module or applying too much pressure may
damage it. If the module does not readily press into place, remove it, check for bent pins or out-of-
place keying pins, and try again.
15
CTR-1462 – User’s Manual
J5: PCI Slot Selection
Figure 9. J5 layout
Label Type
J5
Options Function Default
4-3 1-2 Slot #
Closed Closed 3
Closed Open 2
Open Closed 1
J5 Pinstrip 2x2
Pitch 2.54 mm
Selection of PCI slot
Open Open 0
Slot 0
Table 2. PCI slot selection
Note:
The PCI slot selection must be set to reflect the PCI device stack configuration, the
board closest to the PCI should be set for slot # 0 and so on in numerical order. If slot
selections are not correctly configured bus conflicts and PCI-bus operation may be
non-functional and prevent the operation of the CPU. Please refer to the PC/104Plus
specification for further information on PCI-bus and its configuration.
16
CTR-1462 – User’s Manual
J20: CARDBUS connector
The CARDBUS connector supports both 16-bit legacy-PCMCIA as well as new high-speed 32-bit CARDBUS
expansion devices. The slot is polarized preventing incorrect insertion.
To avoid damage to the pins in the connector make sure the inserted card is clean.
Do not force the card into the slot.
The card will slide into place with limited force applied.
Once the expansion card is fully inserted the eject button will be pushed out.
To release the card from the slot gently push the eject button releasing the card.
Carefully remove the card from the slot.
Eject button
17
Figure 10. J20 layout
J20
Insert card
this side
(This page is intentionally left blank.)
CTR-1462 – User’s Manual
Appendix
A.1. Mechanical Dimensions
96.0
90.2
5.1
5.1
8.9
7.6
Ø 6.4 PAD
Ø 3.2 HOLE
73.7
5.1
5.1
Dimensions are in millimetres
Figure 11. CTR-1462 Board dimensions
Note:
For further information about the mechanical dimensions of ISA and PCI buses
please refer to the PC/104 consortium site (www.pc104.org)
19
CTR-1462 – User’s Manual
20
A.2. Manual Revision History
REVISION DESCRIPTION DATE
1.0 First Release June 2006
1.1
• Updated manual layout
• Updated block diagram
• Updated connector layout
November 2008
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Eurotech CTR-1462 Owner's manual

Eurotech
Brand
Eurotech
Model
CTR-1462
Type
Owner's manual

Eurotech CTR-1462 is a PC/104-Plus Single Slot PCMCIA/CARDBUS Interface Board. It provides a single ISA bus connector and a single PCI bus connector, allowing you to connect ISA and PCI devices to your PC/104-Plus system. The CTR-1462 also features a CARDBUS connector, which allows you to connect CARDBUS devices to your system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents