Advantech B+B SmartWorx SEG528-4SFP-T Quick start guide

B+B SmartWorx SEG528-4SFP-T
Advantech
Brand
Advantech
Model
B+B SmartWorx SEG528-4SFP-T
Category
Network switches
Type
Quick start guide

Advantech B+B SmartWorx SEG528-4SFP-T is a 24-port 10/100/1000 Mbps + 4-port Gigabit Combo (RJ45 or SFP) Uplink Industrial Managed Ethernet Switch designed for harsh industrial environments with an extended operating temperature range of -40 to 70°C. It features SFP ports for flexible uplink options, PoE (Power over Ethernet) support on the RJ45 ports, and advanced management capabilities for demanding industrial applications.

Advantech B+B SmartWorx SEG528-4SFP-T is a 24-port 10/100/1000 Mbps + 4-port Gigabit Combo (RJ45 or SFP) Uplink Industrial Managed Ethernet Switch designed for harsh industrial environments with an extended operating temperature range of -40 to 70°C. It features SFP ports for flexible uplink options, PoE (Power over Ethernet) support on the RJ45 ports, and advanced management capabilities for demanding industrial applications.

Product Overview
Hardware Installation
1
Terminal Blocks
Terminal Description
V2- Power Input 2 (DC Ground)
V2+ Power Input 2 (12 to 48VDC)
P-Fail Power Fault Relay
P-Fail Power Fault Relay
V1- Power Input 1 (DC Ground)
V1+ Power Input 1 (12 to 48VDC)
LED Status
3
LED Status Description
SYS
Green System is operating normally
Off
No Power / system crash /
operation initiating
PWR1
Green Powered up
Off Power down or not installed
PWR2
Green Powered up
Off Power down or not installed
P-Fail
Solid Red
When PW1 or PW2 is dis-
connected, the LED lights.
Off
When PW1 and PW2 is con-
nected, the LED is off.
LOOP
Detection
Solid Red
When loop detected, the
LED lights.
Off No loop detected.
R.M.
Solid
Green
An active switch within the
ring is a designated ring
master.
Off
No ring master determined in
current ring.
Ring Fail
Solid Red
A ring port within the ring
loop is identied has having
a ring ID within a second ring
loop.
Off
No ring ports having a ring ID
within a secondary ring
loop are detected.
Temp
Solid Red
IC sensor detects a tempera-
ture range exceeding set
temperature range.
Off
IC sensor detects normal
operating temperature.
LED Status Description
SFP LED
Solid Green
SFP or GBIC plug-in and link
up.
Blink Green Packet transmit and receive.
Off
SFP or GBIC plug-out or link
down.
PoE
(SEGP528)
Solid Green
Connect to PD and supply
power.
Blink Green Not applicable.
Off
Disconnect from PD and No
supply Power.
LNK/ACT
Solid Green Current link speed is 1000M.
Blink Green Packet transmit and receive.
Off No link.
Solid Amber
Current link speed is
100/10M.
Blink Amber Packet transmit and receive.
Off No link.
Solid Green
Connect to PD and supply
power.
2
Wire Gauge: 12-24 AWG (3.31 - 0.205 mm2).
Torque: 7lb-in.
NOTE: P-Fail Relay is closed if both power input ports
are powered. The default is open.
System LED
Panel
100/1000
SFP Ports
10/100/1000
Ethernet Ports
10/100/1000
Ethernet Ports
SFP LEDs
Console Serial
Port (Back)
GND (Back)
Power (Back)
Rack Mounting
System
1. Align the rack mount brackets with the holes on the
switch
2. Secure the rack mount brackets with the provided
screws
3. Align the switch with the posts on the rack cabinet
SFP
Recommended Accessories
MDR-40-24
Power Supply
C5UMB3FBG
Ethernet Cables
Document number – SEGP528-4SFP-T_0817qsg
1-888-948-2248 | Europe: +353 91 792444
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: 815-433-5100 | Fax: 815-433-5109
www.advantech-bb.com | E-mail: support@advantech-bb.com
Before you begin, be
sure you have the following:
SEG528-4SFP-T &
SEGP528-4SFP-T
Industrial Managed Ethernet Switch
Fast and easy on the web:
www.advantech-bb.com
+ Ethernet Switch
+ Power Supply (Required not included)
QUICK START
GUIDE
Troubleshooting
Default Settings
If no LEDs light, verify that the power supply
connections are solid and that power is present
on the output of the power supply.
Use the LED table to verify that power is
present, a link is established, data is being
transmitted, and to verify port speed.
If data does not pass and cable connections
have been veried, contact your Network
Administrator to validate that the network
connection is good.
The user manual can be found in the
documentation and download section of the
product web page.
-- First, go to www.advantech-bb.com.
-- Second, search for the model number.
-- Finally, go to the documentation/download
section of that product page to download
les.
IP Address: 192.168.1.1
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.254
Username: admin
Password: admin
Product Information
MODEL # DESCRIPTION
TEMP
RATING
SEGP528-
4SFP-T
24-port 10/100/1000 Mbps + 4-port
Gigabit Combo (RJ45 or SFP)
Uplink Industrial Managed Ethernet
Switch
-40 ~ 70°C
  • Page 1 1
  • Page 2 2

Advantech B+B SmartWorx SEG528-4SFP-T Quick start guide

B+B SmartWorx SEG528-4SFP-T
Advantech
Brand
Advantech
Model
B+B SmartWorx SEG528-4SFP-T
Category
Network switches
Type
Quick start guide

Advantech B+B SmartWorx SEG528-4SFP-T is a 24-port 10/100/1000 Mbps + 4-port Gigabit Combo (RJ45 or SFP) Uplink Industrial Managed Ethernet Switch designed for harsh industrial environments with an extended operating temperature range of -40 to 70°C. It features SFP ports for flexible uplink options, PoE (Power over Ethernet) support on the RJ45 ports, and advanced management capabilities for demanding industrial applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents