SAFETY INSTRUCTIONS
Carefully Read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written
consent from Dynabrade, Inc.
Tool Intent: 11" Gear-Driven Sander are ideal for removal and polishing of materials using deburring, cleaning and polishing accessories.
Do Not Use Tool For Anything Other Than Intended Applications.
This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.
Training: Proper care, maintenance, and storage of your tool will maximize their performance.
• Employer's Responsibility – Provide 11" Gear-Driven Sander operators with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.
• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
• Use only recommended accessories. See back page of manual and Dynabrade catalog.
• Follow tool specifications before choosing size and type of accessory.
• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG
(10 Bars, g) or 150 percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
Parts Page Reorder No. PD06•11R
Effective December, 2013
Supersedes PD06•11
11" Gear-Driven Sander
Air Tool Manual – Safety, Operation and Maintenance
Models:
58040 – 11" Pad, 3/16" Orbit, Non-Vac
58041 – 11" Pad, 3/16" Orbit, Central-Vac
SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL
SAFETY LEGEND
WARNING
WARNING
Read and understand tool manual before
work starts to reduce risk of injury to
operator, visitors, and tool.
WARNING
Eye protection must be worn at all times,
eye protection to conform to ANSI Z87.1.
WARNING
Respiratory protection to be used when exposed to
contaminants that exceed the applicable threshold
limit values required by law.
WARNING
Practice safety requirements. Work alert,
have proper attire, and do not operate tools under
the influence of alcohol or drugs.
WARNING
Ear protection to be worn when exposure to sound,
exceeds the limits of applicable Federal, State or
local statues, ordinances and/or regulations.
WARNING
Air line hazard, pressurized supply lines and flexible
hoses can cause serious injury. Do not use damaged,
frayed or deteriorated air hoses and fittings.
Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel
as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety Institute
(ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the Use, Care
and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for Standards
(EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.
WARNING
Some dust created by sanding, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM
To Tool Station
Closed Loop Pipe System
(Sloped in the direction of air flow)
Ball
Valve
Ball
Valve
Filter
Regulator
Lubricator
Air Flow
Drain
Valve
Drain
Valve
Air Tool
Air Compressor
and Receiver
Drain Valve
Air Hose
90 PSIG MAX
(6.2 Bar)
Air Flow
Refrigerated
Air Dryer
2
Filter
Regulator
Lubricator
90 PSIG
(6.2 Bar)
OPERATING INSTRUCTIONS
Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.
Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
• Keep hand and clothing away from working end of the air tool.
Operation: Be sure that any loose clothing, hair and all jewelry is properly restrained.
• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.
• BEFORE MOUNTING AN ACCESSORY, after all tool repairs and whenever a 11" Gear-Driven Sander is issued for use, check tool RPM (speed) with
tachometer with air pressure set at 90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool housing, or
operating improperly, the tool must be serviced and corrected before use.
Caution:Tool RPM must never exceed abrasive/accessory RPM rating. Check accessory manufacturer for details on maximum operating speed or special
mounting instructions.
• With power source connected at the air tool relieve hose of air pressure and disconnect tool from air supply when changing recommended accessories.
• Connect air tool to power source. Be careful NOT to depress throttle lever in the process.
• Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).
Caution: After installing the accessory, before testing or use and/or after reassembling tool, the 11" Gear-Driven Sander must be started at a reduced
speed to check for good balance. Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to
insure safe operation.
• Use only coated abrasive sanding discs or sheets properly secured to the backing pad provided with the air sander. Ensure that self-fixing sanding discs
are mounted concentrically.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris. Potentially explosive atmospheres can be caused
by dust and fumes resulting from sanding or grinding. Always use dust extraction or suppression systems which are suitable for the
material being processed.
• Proceed with caution in unfamiliar surroundings. Hidden hazards may exist, such as electricity or other utility lines.
• Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electric power sources.
• Use a vise or clamping device to hold work piece firmly in place.
• Work may generate hazardous dust.
• Do not apply excessive force on tool or apply “rough” treatment to it.
• Always work with a firm footing, posture and proper lighting.
• Ensure that sparks and debris resulting from work do not create a hazard.
• This tool is rear exhaust. Exhaust may contain lubricants, vane material, bearing grease, and other materials flushed thru the tool.
Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.
Air System
1 DROP/MIN.
20 SCFM
LUBRICATOR SETTING
•
Dynabrade Air Power Tools are designed to
operate at 90 PSIG (6.2 Bar/620 kPa) maximum
air pressure at the tool inlet, when the tool is
running. Use recommended regulator to control
air pressure.
•
Ideally the air supply should be free from moisture.
To facilitate removing moisture from air supply,
the installation of a refrigerated air dryer after the
compressor and the use of drain valves at each
tool station is recommended.
➤
➤
➤
➤
➤
➤
Maintenance Instructions
Important: A preventative maintenance program is recommended whenever portable power tools are used. The program should include inspection of air
supply lines, air line pressure, proper lubrication and repair of tools. Refer to ANSI B186.1 for additional maintenance information.
•
Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
•
It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due
to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Filter-Regulator-Lubricator (FRL) – Provides accurate
air pressure regulation and two stage filtration of water contaminants. Operates 40 SCFM @ 100 PSIG with 3/8" NPT female ports.
•
Use the 95541 Grease Gun to apply 2 full plunges of the 95542 Grease through the grease fitting located in the 56452 Mount Plate Assembly.
Two full plunges of grease should be applied after every 300-hour interval of use.
•
Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
Routine Preventative Maintenance:
•
Check free speed of 11" Gear-Driven Sander by using a tachometer on regular basis.
•
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
•
DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
®
).
•
A Motor Tune-Up Kit (P/N 96576) is available which includes high wear and medium wear motor parts.
•
Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification information i.e.:
Model #, S/N, and RPM. (See Assembly Breakdown)
•
Blow air supply hose out prior to initial use.
•
Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
•
Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
•
Use of tool rests, hangers and/or balancers is recommended.
•
Protect tool inlet from debris (see Notice below).
•
DO NOT carry tool by air hose, or near the tool throttle lever.
•
Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
•
Store accessories in protective racks or compartments to prevent damage.
•
Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain
materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks
which can cause fires or explosions. It is the users responsibility to make sure the work area is free of flammable materials.
Notice
All Dynabrade motors use the highest quality parts and materials available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Machine Specifications
3
Model Motor Motor Pad Dia. Sound Maximum Air Flow Hose I.D. Air Inlet Weight Length Height
Number hp (W) RPM Inch (mm) Level CFM/SCFM (LPM) Size Thread Pound (kg) Inch (mm) Inch (mm)
58040 .45 (336) 950 11 (279) 86 dB(A) 3/23 (651) 1/4" or 8mm 1/4" NPT 5.0 (2.3) 14-3/32 (358) 5-10/16 (143)
58041 .45 (336) 950 11 (279) 86 dB(A) 3/23 (651) 1/4" or 8mm 1/4" NPT 5.5 (2.5) 14-3/32 (358) 5-10/16 (143)
Additional Specifications: Air Pressure 90 PSIG (6.2 Bar)
11" Gear-Driven Sander
Complete Assembly
O
1
O
1
O
1
O
1
G
1
A
10
O
1
A
10
O
1
3 N•m
T
3 N•m
T
3 N•m
T
9 N•m
T
34 N•m
T
34 N•m
T
HOUSING MODEL
ASSEMBLY # NUMBER
59221 58040
59222 58041
1
2
3
4
5
6
9
10
11
12
14
18
20
21
22
23
41
24
25
28
27
30
31
32
33 34
36
39
40
1 97010 Screw (5)
2 95886 Washer (5)
3 56231 11" Pad
(Optional Pads Pg.8)
4 96477 Screw
5 Balance Arm Assembly:
59277 11"
6 56474 Balancer Washer
7 56452 Mount Plate Assembly
8 Shroud:
56489 Non-Vacuum
61368 Vacuum Shroud Assy.
Assembly Includes:
A 61361 Lip Seal
B 95886 Washer (6)
C 96425 Screw (6)
D 61362 1-1/4" Vac Adapter
9 01673 Pin
10 56589 Shaft
11 54673 Key
12 56133 Bearing
13 57749 Pinion Gear
14 57332 Lock Ring
15 96166 Set Screw
16 56559 Front Bearing Plate
17 54705 Rotor/Blade Set (5/pkg.)
18 56495 Cylinder
(Includes: 95865 & 96313 Pins)
19 95911 O-Ring
20 54629 Rear Bearing Plate
21 01206 Bearing
22 95626 Retaining Ring
23 Housing: See Chart
(Incudes: 56581 Grip)
24 95627 Pin
25 56582 Safety Throttle Lever
26 98459 O-Ring
27 56579 Valve Stem
28 56578 Speed Regulator
29 01025 O-Ring (3)
30 56598 Seal
31 51944 Tip Valve
32 51943 Spring
33 56586* Vacuum Plug
34 56469 Exhaust Gasket
35 96459 O-Ring
36 56468 Handle Assembly
(Includes: 51938 Screen)
37 96469 Screw (2)
38 96454 Screw (2)
39 56597* Muffler
40 56596* Muffler Clip
Index Key
No. Part # Description
Adhesive: A
10
= Loctite #243
Torque: N•m x 8.85 = In. - lbs.
Grease: G
1
= Lubriplate 630 AA
Oil: O
1
= Air Lube
O
A
T
G
KEY
26
29
35
17
19
13
37
38
*Parts included with Non-Vacuum
Models Only.
8
G
1
7
4
16
15
41 00000905 Warning Label
Label Key
No. Part # Description
Vacuum Shroud Assembly
C
A
D
C
B
B
Disassembly/Assembly Instructions
Important: The manufactures warranty is void if the tool is disassembled before the warranty expires. Use these instructions in conjunction with the Part
Number 96283 Tool Repair Kit. This kit includes special tooling for the proper disassembly/assembly of the Two-Hand Gear-Driven Sander. This Tooling will
be referred to in these instructions. An air motor Tune-Up Kit, Part Number 98221 is also available. It contains the high and medium wear components that
most commonly need replacement.
Motor Disassembly:
1. Shut the air supply and disconnect the sander from the air supply hose.
2. Use the 57092 Repair Collar to hold the sander in a vise. Position the sander so that the backing pad is facing up. Note: Do not over tighten the collar and sander in the
vise. Hold the sander snugly, so that the motor lock ring can be removed easily.
3. Use a 9/64" hex key wrench to remove the screws and backing pad from the sander.
4. Use a 4mm hex key wrench to remove the balance arm assembly by turning the hex key counterclockwise.
5. Remove the 56474 Balance Washer and 56452 Mount Plate Assembly. Remove 96166 Set Screw.
6. Use the 56599 Lock Ring Tool to remove the 57332 Lock Ring by turning it counterclockwise.
7. Pull the air motor assembly out of the housing.
8. Use retaining ring pliers to remove the 95626 Retaining Ring.
9. Remove the 95911 O-Ring from the 56495 Cylinder and fasten a 2" bearing separator around the part of the cylinder that is closest to the 54629 Rear Bearing Plate.
10. Place the air motor with the bearing separator attached, onto the table of the 96232, #2 Arbor Press so that the balance end of the 56589 Shaft is pointing down.
11. Use a 5/16" dia. flat end drive punch as a press tool to push the shaft out of the 01206 Bearing. Use the 96213 Bearing Removal Tool to push the 01206 Bearing out of the
54629 Rear Bearing Plate. Note: This bearing removal tool is not included in the 96283 Repair Kit. Use the removal tool to push the 01206 Bearing out of the 54629 Rear
Bearing Plate.
12. Remove the cylinder, rotor, vanes, and key.
13. Secure the 96249 Collar around the outside diameter of the 56559 Front Bearing Plate.
14. Secure the collar in a vise so that the pinion gear is facing up. Use a Heat Gun to apply heat to the pinion gear. Use the 96181 Pinion Wrench or adjustable groove pliers to
grip the pinion gear and turn counterclockwise to remove it from the 56559 Front Bearing Plate.
15. Use a 2" bearing separator and arbor press to remove the 57749 Pinion Gear from the 56559 Front Bearing Plate.
16. Disassemble mounting plate sub-assembly:
a.) Remove 96276 Nuts (4) and 96274 Screws then lift out gear.
b.) Remove 96118 Screws (3).
c.) Press out 96423 Bearing by using
57091 Bearing Press Tool.
Motor Disassembly Complete.
Motor Assembly:
Important: Clean and inspect all motor parts for wear or defect.
1. Install 56133 Bearing on the balance end of the 56589 Shaft.
2. Use the small end of the 50791 Bearing Press Tool and the 96232, #2 Arbor Press to push the 56133 Bearing onto the shaft until the I.D. of the bearing sits against the
shaft step. (Drawing 1)
3. Install the 57332 Lock Ring onto the 56559 Front Bearing Plate so that the threaded portion of the lock ring sits against the bearing plate.
4. Secure the 96249 Collar around the outside diameter of the 56559 Front Bearing Plate.
5. Secure the collar in a vise so that the thread of the lock ring is facing up. Apply a small amount of Loctite #243 (or equivalent) to the thread of the lock ring. Position the
counter-bored end of the pinion gear toward the lock ring. By hand install the pinion gear. Use the 96181 Pinion Wrench or adjustable groove pliers to grip the pinion gear
and turn clockwise to secure it to the 56559 Front Bearing Plate. (Torque to 34•Nm/300 in. lbs.)
6. Mounting Plate Sub-Assembly:
a.) Press 96423 Bearing into mounting plate.
b.) Insert 96118 Screws (3) and apply 1 drop of #271 Loctite
®
(or equivalent). Note: All screws should be hand tight before torque is applied.
c.) Press 57749 Gear into mounting plate, making sure to align mounting holes and that the 96273 O-Ring on back of gear is in place before assembly to mounting plate.
d.) Insert 96275 Washers into c-bore in gear.
e.) Apply 1 drop of #271 Loctite
®
(or equivalent) to 96274 Screws (4), insert through gear and thread into mounting plate torque 7 N•m/60 in. - lbs. Insert 96276 Nuts (4)
and torque 7 N•m/60 in. - lbs.
7. Use the large end of the 57091 Bearing press Tool and the arbor press to install the front bearing plate onto the 56133 Bearing. (Drawing 2)
8. Install the 54673 Key so that the 90° side of the key fits into the keyway of the shaft and the tapered side of the key fits into the rotor. Install the 54705 Rotor/Blade Set (5)
onto the shaft
9. Apply the 95842 Dynabrade Air Lube (10W/NR or equivalent) to the blades.
10. Install the 56495 Cylinder over the rotor so that the short line-up pin fits into the front bearing plate.
11. Place the 54629 Rear Bearing Plate over the shaft so that the long line-up pin fits through the hole in the rear bearing plate.(Drawing 3) Use the small end of the 57091
Bearing Press Tool to install the 01206 Bearing onto the shaft and into the 54629 Rear Bearing Plate. Use the press tool and the arbor press to install these so that there is
a snug fit between the bearing plates and the cylinder. Note: Carefully press the 01206 Bearing onto the motor shaft until it touches against the bearing seat on the inside
of the bearing plate. (Drawing 4)
12. Use retaining ring pliers to install the 95626 Retaining Ring so that the concave side of the ring is toward the motor assembly. Note: Be sure that the retaining ring is com-
pletely pressed down into the groove on the shaft.
13. Use the 57092 Repair Collar to hold the housing in a vise so that the opening for the housing is facing up. Note: Do not over tighten the collar and housing in the vise. Only
hold the housing snugly, so that the motor and lock ring can be installed easily.
14. Apply a small amount of petroleum lubricant to the 95911 O-Ring and install the o-ring into the air inlet hole in the cylinder.
15 Install the motor assembly into the housing making sure to align the line-up pin with the line-up hole that is on the inside of the housing.
16. Use the 56599 Lock Ring Tool to secure the motor in the housing. (Torque to 34 N·m/300 in. lbs.) Align holes in 57332 Lock Ring with holes in housing.
17. Use 2mm hex key and install 96166 Set Screw into the housing through one of the holes in the lock ring until set screw is flush with the top of the lock ring.
18. Install the appropriate shroud onto the housing.
19. Apply a small mount of the 95542 Grease to the mount plate gear and then install the 56452 Mount Plate Assembly and the 56474 Balance Washer onto the 56589 Shaft.
Apply a small amount of the Loctite #243 (or equivalent) to the threads of the 96477 Screw. Hold the balance arm assembly stationary with an adjustable wrench and use a
5/32" hex key to tighten the 96477 Screw by turning it clockwise. (Torque to 9N·m/80 in. lbs.)
20. Use the 95541 Grease Gun to apply 2 full plunges of the 95542 Grease through the grease fitting that is located in the 56452
Mount Plate Assembly. Two full plunges of
grease should be applied after every 300-hour interval of use.
21. Use a 9/64" hex key wrench to install a weight-mated sanding pad.
Motor Assembly Complete.
5
Diagrams
Drawing 1 Drawing 2 Drawing 3 Drawing 4
57091
Bearing Press Tool
57091
Bearing Press Tool
57091
Bearing Press Tool
01206
Bearing
Cylinder w/Front
Bearing Plate,
Lock Ring,
Pinion Gear
and Shaft
56495
Cylinder
54629
Rear Bearing Plate
Lock Ring and
Pinion Gear
Lock Ring,
Pinion Gear
and Shaft
56133
Bearing
56589
Shaft
56133
Bearing
Disassembly/Assembly Instructions
Handle and Valve Disassembly:
1. Place the 57092 Repair Collar around the housing so that the handle is pointing up.
2. Use a Phillips
®
screwdriver to remove the four screws that fasten the handle to the housing. Carefully pull the handle from the housing. This provides access to the tip
valve components, also the handle o-ring, gasket and vacuum plug.
3. Use a 1/8" dia. flat end drive punch to remove the 95627 Pin and the 56582 Safety Throttle Lever.
4. Pull the 56578 Speed Regulator and valve stem out of the housing.
Handle and Valve Disassembly Complete.
Handle and Valve Assembly:
1. Place the 57092 Repair Collar around the housing so that the handle mounting area is facing up.
2. Install the 01025 O-Rings (3) onto the 56578 Speed Regulator, apply a small amount of petroleum lubricant to the o-rings and insert the regulator assembly into the
housing. Note: Be careful that the o-rings do not get caught and pulled out of the o-ring grooves.
3. Install the 98459 O-Ring onto the 56579 Valve Stem, apply a small amount of petroleum lubricant to the o-ring and insert the shortest portion (from the end to the o-ring) of
the valve stem assembly into the speed regulator.
4. Install the 56582 Safety Throttle Lever onto the housing and secure it in place with the 95627 Pin.
5. Install the 56598 Seal into the air inlet passage of the housing.
6. Install the 56586 Vacuum Plug into the exhaust passage of the housing. (See Exploded View)
7. Use needle-nose pliers to grasp and install the 51944 Tip Valve so that it fits under the end of the 56579 Valve Stem.
8. Install the large end of the 51943 Spring into the air inlet passage of the handle.
9. Install the 56469 Gasket onto the mounting surface of the handle.
10. Apply a small amount of petroleum lubricant to the 96459 O-Ring and install it onto outside diameter of the air inlet passage at the location of the first shoulder.
11. Connect the handle to the housing and secure it in place with the four screws. Note: The two longer screws, Part Number 96454 (2) secure the 56581 Grip to the housing.
12. Install the 56597 Muffler and secure it in place with the 56596 Muffler Clip. (See Exploded View)
Handle and Valve Assembly Complete. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should
be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool
for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Special Repair Tools
96232 (#2) Arbor Press
•
This arbor press is ideal for the disassembly
and assembly of air motors.
96346 2" Bearing Separator
•
Use the separator to remove gears
and bearings.
96182 Removal Tool
•
Has a
3/8" square socket
for use with 3/8" drive; breaker bar,
ratchet head, or torque wrenches.
96283 Motor Repair Kit:
•
Contains special tools for
disassembly/assembly of machine.
96213 Bearing Removal Tool
•
This tool is used to pass through the I.D.
of the bearing plate and to push against
the I.D. of the bearing.
96343 Retaining Ring Pliers
•
Internal/external retaining ring pliers.
Tip diameter - 0.038" (0.96mm)
6
This service chart is published as a guide to expectant life of component parts. The replacement levels are based on average tool
usage over one year. Dynabrade Inc. considers one year usage to be 1,000 hours or 50% of a man year. Parts included in motor
tune-up kit are identified by High Wear and Medium Wear items.
Parts Common to all Models:
Preventative Maintenance Schedule
For All 11" Gear-Driven Sander
98576 – Motor Tune-Up Kit
LEGEND
T Included in Tune-Up Kit
X Type of wear, no other
comments apply.
L Easily lost. Care during
assembly/disassembly.
D Easily damaged during
assembly/disassembly.
R Replace each time tool is
disassembled.
Note: Please refer to page 4 of tool manual for specific part number.
7
Index Part Description Number High Wear Medium Wear Low Wear Non-Wear
# Number Required 100% 70% 30% 10%
1 97010 Screw 5 L
2 95886 Washer 5 L
3 56231 11" Pad 1 X
4 96477 Screw 1 L
5 59277 11" Balance Arm Assy 1 X
6 56474 Balancer Washer 1 L
7 58452 Mount Plate Assembly 1 X
Includes: 96423 Bearing 1 T
8
See Note Shroud 1 X
9 01673 Pin 1 D
10 56589 Shaft 1 X
11 54673 Key 1 T
12 56133 Bearing 1 T
13 57749 Pinion Gear 1 X
14 57332 Lock Ring 1 X
15 96166 Set Screw 1 L
16 56559 Front Bearing Plate 1 X
17 54705 Rotor/Blade Set (5/pkg.) 1 T
18 56495 Cylinder
(95865 & 96313 Pin) 1 X
19 95911 O-Ring 1 T
20 54629 Rear Bearing Plate 1 X
21 01206 Bearing 1 T
22 95626 Retaining Ring 1 T
23
See Note Housing (Includes: 56581 Grip) 1 X
24 95627 Pin 1 T
25 56582 Safety Throttle Lever 1 X
26 98459 O-Ring 1 T
27 56579 Valve Stem 1 T
28 56578 Speed Regulator 1 X
29 01025 O-Ring 3 X
30 56598 Seal 1 T
31 51944 Tip Valve 1 T
32 51943 Spring 1 T
33 56586 Vacuum Plug 1 X
34 56469 Exhaust Gasket 1 T
35 96459 O-Ring 1 T
36 56468 Handle
(Includes: 51938 Screen) 1 X
37 96469 Screw 2 X
38 96454 Screw 2 X
39 56597 Muffler 1 T
40 56596 Muffler Clip 1 T
DYNABRADE
®
DYNABRADE, INC.,
8989 Sheridan Drive
•
Clarence, NY 14031-1490
•
Phone: (716) 631-0100
•
Fax: 716-631-2073
•
International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
Zone Artisanale
•
L-5485 Wormeldange—Haut, Luxembourg
•
Telephone: 352 76 84 94 1
•
Fax: 352 76 84 95 1
© DYNABRADE, INC., 2013 12/13 PRINTED IN USA
Visit Our Web Site: www.dynabrade.com Email: [email protected]
98576 Motor Tune-Up Kit
•
Includes assorted parts to
help maintain and repair motor.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1 gal. (3.8 L)
Optional 11" Pads:
56230 Vinyl
56232 Loop-Face
56220 HookIt
TM
II Interface Pad
56231 Hook-Face
53997 Hook-Face, Vac (15 Hole)
53998 Interface Pad (Hook-Face)
Optional Accessories
95542 Grease 10 oz.
•
Multi-purpose grease for all types of
bearings, cams, gears.
•
High film strength; excellent resistance to
water, steam, etc.
•
Workable range 0˚ F to 300˚ F.
95541 Push-type Grease Gun
•
One-hand operation.
95134 – 9/64" Hex Wrench
95135 – 5/32" Hex Wrench
FIND THE MOST CURRENT OFFERING OF SUPPORT DOCUMENTS AND ACCESSORIES @ WWW.DYNABRADE.COM
Reference Contact Information
1. American National Safety Institute – ANSI
1899 L Street, NW 11th Floor
Washington, DC 20036
202-293-8020
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: 1 (202) 512-1803
3. Eurpoean Committee for Standardization
Rue de Stassart 36
B - 1050 Brussels, Belgium
/
