Philips GC4250/02 User manual

Page is loading ...

Important

Read these instructions for use carefully before using the appliance and

save them for future reference.

◗ Check if the voltage indicated on the type plate corresponds to

the local mains voltage before you connect the appliance.

◗ Only connect the appliance to an earthed wall socket.

◗ Do not use the appliance if the plug, the cord or the appliance

itself shows visible damage, or if the appliance has been dropped

or is leaking.

◗ Check the cord regularly for possible damage.

◗ If the mains cord is damaged, it must be replaced by Philips, a

service centre authorised by Philips or similarly qualified persons

in order to avoid a hazard.

◗ Never leave the appliance unattended when it is connected to the

mains.

◗ Never immerse the iron and the stand, if provided, in water.

◗ Keep the appliance out of the reach of children.

◗ The soleplate of the iron can become extremely hot and may

cause burns if touched.

◗ Do not allow the cord to come into contact with the soleplate

when it is hot.

◗ When you have finished ironing, when you clean the appliance,

when you fill or empty the water tank and also when you leave

the iron even for a short while: set the steam control to position

O, put the iron on its heel and remove the mains plug from the

wall socket.

◗ Always place and use the iron and the stand, if provided, on a

stable, level and horizontal surface.

◗ Do not put perfume, vinegar, starch, descaling agents, ironing aids

or other chemicals in the water tank.

◗ This appliance is intended for household use only.

Before first use

1 Check if the voltage indicated on the appliance corresponds to

the local mains voltage before you connect the appliance.

C

2 Remove the protective heat cover from the soleplate (type

GC4243 only). Remove any sticker or protective foil from the

soleplate.

3 Let the iron heat up to maximum temperature and pass the

iron over a piece of damp cloth for several minutes to remove

any residues from the soleplate.

B

The iron may give off some smoke when you use it for the first time.This

will cease after a short while.

ENGLISH4

Preparing for use

Filling the water tank

Never immerse the iron in water.

1 Remove the mains plug from the wall socket.

C

2 Set the steam control to position O (= no steam).

3 Open the cap of the filling opening.

4 Tilt the iron backwards.

C

5 Fill the water tank with tap water up to the maximum level by

means of the filling cup.

Do not fill the tank beyond the MAX indication.

◗ If the tap water in your area is very hard, we advise you to mix it

with an equal amount of distilled water or to use distilled water

only.

Do not put additives, vinegar, starch or chemically descaled water in the

water tank.

C

6 Close the cap of the filling opening.You will hear a click.

Setting the temperature

C

1 Type GC4243 only: remove the protective heat cover.

Do not leave the protective heat cover on the soleplate during ironing.

2 Put the iron on its heel.

C

3 Set the temperature dial to the required ironing temperature

by turning it to the appropriate position.

- Check the garment label for the required ironing temperature.

- 1 Synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)

- 1 Silk

- 2 Wool

- 3 Cotton, linen

ENGLISH 5

N

Y

L

O

N

S

O

I

E

L

A

I

N

E

C

O

T

O

N

L

I

N

Y

L

O

N

S

I

L

K

W

O

L

C

O

T

O

N

L

I

N

E

N

6

- If you do not know what kind(s) of fabric(s) an article is made of,

determine the right ironing temperature by ironing a part that will

not be visible when you wear or use the article.- Silk, woollen

and synthetic materials: iron the reverse side of the fabric to prevent

shiny patches.Avoid using the spray function to prevent stains.

- Start ironing the articles that require the lowest ironing temperature,

such as those made of synthetic fibres.

4 Put the mains plug in an earthed wall socket.

C

5 When the amber temperature pilot light has gone out, wait a

while before you start ironing.

The amber pilot light will go on from time to time during ironing.

Using the appliance

Steam ironing

1 Make sure that there is enough water in the water tank.

C

1 Select the appropriate steam setting. Make sure that the steam

setting you select is suitable for the ironing temperature

selected:

- 1 - 3 for moderate steam (temperature settings 2 to 3)

- 4 - 6 for maximum steam (temperature settings 3 to MAX)

See 'Setting the temperature'.

B

The iron will start producing steam as soon as the set temperature has

been reached.

Ironing without steam

C

1 Set the steam control to position O (= no steam).

2 Select the recommended ironing temperature.

See 'Setting the temperature'.

ENGLISH

7

Features

Spraying

You can use the spray function to remove stubborn creases at any

temperature.

Make sure that there is enough water in the water tank.

C

1 Press the spray button several times to moisten the article to

be ironed.

Shot of steam

A powerful 'shot' of steam helps remove stubborn creases.

The shot-of-steam function can only be used at temperature settings

between 2 and MAX.

C

1 Press and release the shot-of-steam button.

Drip stop

This iron is equipped with a drip-stop function: the iron automatically

stops producing steam when the temperature is too low to prevent

water from dripping out of the soleplate.When this happens you may

hear a sound.

Vertical shot of steam

C

1 The shot-of-steam function can also be used when you hold

the iron in vertical position.

Never direct the steam at people.

ENGLISH

8

Automatic anti-calc function

C

1 The built-in anti-calc system reduces the build-up of scale and

guarantees a longer life for the iron.

Electronic safety shut-off function (Types GC4243, GC4238,

GC4233 only)

C

1 The electronic safety shut-off function automatically switches

off the iron if it has not been moved for a while.

◗ The red auto-off pilot light starts blinking to indicate that the iron

has been switched off by the safety shut-off function.

To let the iron heat up again:

- Pick up the iron or move it slightly.

- The red auto-off pilot light goes out. If the temperature of the

soleplate has dropped below the set ironing temperature, the amber

temperature pilot light goes on.

- If the amber pilot light goes on after you have moved the iron, wait

for it to go out before you start ironing.

- If the amber pilot light does not go on after you move the iron, the

soleplate still has the right temperature and the iron is ready for use.

Alert light

C

◗ Types GC4243 and GC4238 only:

- The iron is equipped with a blue alert pilot light.

- The blue alert light burns as long as the iron is plugged in, even if the

iron has been switched off by the safety shut-off function.

ENGLISH

9

Cleaning and maintenance

Using the calc-clean function

You can use the calc-clean function to remove scale and impurities.

◗ Use the calc-clean function once every two weeks. If the water in

your area is very hard (i.e. when flakes come out from the

soleplate during ironing), the calc-clean function should be used

more frequently.

1 Set the steam control to position O.

2 Fill the water tank to the maximum level.

Do not put vinegar or other descaling agents in the water tank.

C

3 Select the maximum ironing temperature.

4 Put the plug in the wall socket.

5 Unplug the iron when the amber temperature pilot light has

gone out.

C

6 Hold the iron over the sink, press and hold the calc-clean

button and gently shake the iron to and fro.

B

Steam and boiling water will come out of the soleplate. Impurities and

flakes (if any) will be flushed out.

7 Release the calc-clean button as soon as all the water in the

tank has been used up.

Repeat the calc-clean process if the iron still contains a lot of impurities.

After the calc-clean process

- Put the plug in the wall socket and let the iron heat up to allow the

soleplate to dry.

- Unplug the iron when it has reached the set ironing temperature.

- Move the hot iron gently over a piece of used cloth to remove any

water stains that may have formed on the soleplate.

- Let the iron cool down before you store it.

After ironing

1 Remove the mains plug from the wall socket and let the iron

cool down.

2 Wipe flakes and any other deposits off the soleplate with a

damp cloth and a non-abrasive (liquid) cleaning agent.

ENGLISH

N

Y

L

O

N

S

O

I

E

L

A

I

N

E

C

O

T

O

N

L

I

N

Y

L

O

N

S

I

L

K

W

O

L

C

O

T

O

N

L

I

N

E

N

10

3 Clean the upper part of the iron with a damp cloth.

C

4 Regularly rinse the water tank with water. Empty the water

tank after cleaning.

Storage

1 Remove the mains plug from the wall socket and set the steam

control to position O.

2 Empty the water tank.

C

3 a) Let the iron cool down.Wind the mains cord around the

cord storage facility and fix it with the cord clip.

b) Always store the emptied iron horizontally on a stable surface and

use a cloth to protect the soleplate.

C

4 Protective heat cover (type GC4243 only)

a) Put the iron on the protective heat cover.

Do not use the protective heat cover during ironing.

b) Wind the mains cord around the cord storage facility.

c) Store the iron with the protective heat cover horizontally on a stable

surface.

Environment

C

◗ Do not throw the appliance away with the normal household

waste at the end of its life, but hand it in at an official collection

point for recycling. By doing this you will help to preserve the

environment.

ENGLISH

Guarantee & service

If you need information or if you have a problem, please visit the Philips

Web site at www.philips.com or contact the Philips Customer Care

Centre in your country (you will find its phone number in the

worldwide guarantee leaflet). If there is no Customer Care Centre in

your country, turn to your local Philips dealer or contact the Service

Department of Philips Domestic Appliances and Personal Care BV.

Troubleshooting

This chapter summarises the most common problems you could

encounter with your iron. Please read the different sections for more

details. If you are unable to solve the problem, please contact the

Customer Care Centre in your country.

11ENGLISH

Solution

Check the mains cord, the plug and

the wall socket.

Fill the water tank (see 'Filling the

water tank').

Set the steam control to a position

between 1 and 6 (see 'Steam ironing').

Select an ironing temperature that is

suitable for steam ironing (2 to

MAX). Put the iron on its heel and

wait until the amber pilot light has

gone out before you start ironing.

Continue ironing in horizontal position

and wait for a while before using the

(vertical) shot-of-steam function again.

Select an ironing temperature that is

suitable for steam ironing (2 to

MAX). Put the iron on its heel and

wait until the amber pilot light has

gone out before you start ironing.

Close the cap properly.You will hear a

click.

Rinse the water tank and do not put

any additive in the water tank.

Use the calc-clean function a few times

(see 'Using the calc-clean function').

Move the iron slightly to deactivate the

safety shut-off function.The pilot light

stops blinking.

Check the mains cord, the plug and

the wall socket.

Possible cause(s)

There is a connection problem.

There is not enough water in the

water tank.

The steam control has been set to

position O.

The iron is not hot enough.

The (vertical) shot-of-steam

function has been used too often

within a very short period.

The iron is not hot enough and/or

the drip-stop function has been

activated.

The cap of the filling opening has

not been closed properly.

An additive has been poured into

the water tank.

You have been using hard water,

which has caused scale flakes to

develop inside the soleplate.

The safety shut-off function has

switched the iron off (see 'Safety

shut-off function')

There is a connection problem.

Problem

The iron is plugged in but the soleplate

is cold.

The iron does not produce any steam.

The (vertical) shot-of-steam function

does not work.

Water droplets drip onto the fabric.

Flakes and impurities come out of the

soleplate during ironing.

The red pilot light blinks (types

GC4243, GC4238 and GC4233 only).

The iron is plugged in but the blue

alert light is out (types C4243 and

GC4238 only).

Page is loading ...

u

4239 000 52404

www.philips.com

Philips GC4250/02 User manual

This manual is also suitable for

Philips GC4250/02 User manual

in other languages

Related papers

Other documents