Rosemount 1067 Temperature Sensors Quick start guide

Rosemount
Brand
Rosemount
Model
1067 Temperature Sensors
Type
Quick start guide
Quick Start Guide
00825-0100-4951, Rev BA
April 2019
Rosemount
™
1067 Temperature Sensors
NOTICE
This guide provides basic guidelines for Rosemount 1067 Sensor models. It does not provide
instructions for configuration, diagnostics, maintenance, service, troubleshooting, explosion-proof,
flameproof, or intrinsically safe (I.S.) installations.
If the Rosemount 1067 Sensor was ordered assembled to a temperature transmitter, see the
appropriate transmitter Quick Start Guide for information on configuration and hazardous locations
certifications.
WARNING
Explosions could result in death or serious injury.
Installation of this sensor in an explosive environment must be in accordance with the appropriate
local, national, and international standards, codes, and practices.
Conduit/cable entries
• Unless marked, the conduit/cable entries in the transmitter housing use a 1/2–14 NPT thread
form. Entries marked “M20” are M20 1.5 thread form. On devices with multiple conduit entries, all
conduit entries will have the same thread form.
• When installing in a hazardous location, use only appropriately listed or Ex certified flameproof/
dust plugs, adapters, or glands in cable/conduit entries.
• Only use plugs, adapters, glands, or conduit with a compatible thread form when closing these
entries.
Contents
Wiring diagrams............................................ 3
Dimensional drawings....................................4
Product certifications.....................................8
Declaration of Conformity............................12
China RoHS.................................................. 14
Quick Start Guide April 2019
2 Rosemount 1067 Temperature Sensor
1 Wiring diagrams
Figure 1-1: Rosemount 1067 RTD Lead Wire Configuration
Figure 1-2: Rosemount 1067 Thermocouple Lead Wire Configuration
Table 1-1: Rosemount 1067 Thermocouple Wire Color
IEC Wire Color ISA Wire Color
Type Positive (+) Negative (-) Positive (+) Negative (-)
E Violet White Violet Red
J Black White White Red
K Green White Yellow Red
N Rose White Orange Red
R Orange White Black Red
S Orange White Black Red
T Brown White Blue Red
April 2019 Quick Start Guide
Quick Start Guide 3
2 Dimensional drawings
Figure 2-1: Rosemount 1067 RTD and Thermocouple
Dimensions are in millimeters.
Table 2-1: Lead Wire Specifications
Approximate lead wire length
(flying leads)
Rosemount
1067
Sensor
Diameter -
mm
Number of
Leads
Element 1 -
mm
Element 2 -
mm
RTD Single
Element
3/6 4 140 N/A
RTD Dual
Element
3/6 6 140 140
Thermocouple
Single Element
3/6 2 140 N/A
Thermocouple
Dual Element
3/6 4 140 140
Quick Start Guide April 2019
4 Rosemount 1067 Temperature Sensor
2.1 Thermocouple characteristics
Table 2-2: Characteristics of 1067 IEC Thermocouples (IEC Standards
Tyically Used in European Applications)
Type Wire alloys Sheath
material
Temperature
range
Interchangeability
error IEC 60584-2
(1)
Accuracy
E Chromel/
Constantan
321 SST -40 to 800 °C
(-40 to 1472 °F)
±1.5 °C (±2.7 °F) or
±0.4%
Class 1
J Iron/
Constantan
321 SST -40 to 750 °C
(-40 to 1382 °F)
±1.5 °C (±2.7 °F) or
±0.4%
Class 1
K Chrome/
Alumel
Alloy 600 -40 to 1000 °C
(-40 to 1832 °F)
±1.5 °C (±2.7 °F) or
±0.4%
Class 1
N Nicrosil/
Nisil
Alloy 660 -40 to 1000 °C
(-40 to 1832 °F)
±1.5 °C (±2.7 °F) or
±0.4%
Class 1
R Platinum -
13%
Rhodium/
Platinum
Alloy 600 0 to 1000 °C (32
to 1832 °F)
±1.0 °C (±1.8 °F) or
±(1+0.3% x
[t-1100])°C
Class 1
S Platinum -
10%
Rhodium/
Platinum
Alloy 600 0 to 1000 °C (32
to 1832 °F)
±1.0 °C (±1.8 °F) or
±(1+0.3% x
[t-1100])°C
Class 1
T Copper/
Constantan
321 SST -40 to 350 °C
(-40 to 662 °F)
±0.5 °C (±1.0 °F) or
±0.4%
Class 1
Table 2-3: Characteristics of 1067 ASTM Thermocouples (ASTM
Standards Tyically Used in North American Applications)
Type Wire alloys Sheath
material
Temperature
range
Interchangeability
error ASTM
E320
(1)
Accuracy
E Chromel/
Constantan
321 SST 0 to 900 °C (32
to 1652 °F)
±1.0 °C (±2.7 °F) or
±0.4%
Special
limits
J Iron/
Constantan
321 SST 0 to 750 °C (32
to 1382 °F)
±1.1 °C (±2.7 °F) or
±0.4%
Special
limits
K Chrome/
Alumel
Alloy 600 0 to 1000 °C (32
to 1832 °F)
±1.1 °C (±2.7 °F) or
±0.4%
Special
limits
N Nicrosil/
Nisil
Alloy 660 0 to 1000 °C (32
to 1832 °F)
±1.1 °C (±2.7 °F) or
±0.4%
Special
limits
April 2019 Quick Start Guide
Quick Start Guide 5
Table 2-3: Characteristics of 1067 ASTM Thermocouples (ASTM
Standards Tyically Used in North American Applications) (continued)
Type Wire alloys Sheath
material
Temperature
range
Interchangeability
error ASTM
E320
(1)
Accuracy
R Platinum -
13%
Rhodium/
Platinum
Alloy 600 0 to 1000 °C (32
to 1832 °F)
±0.6 °C (±1.0 °F) or
±0.1%
Special
limits
S Platinum -
10%
Rhodium/
Platinum
Alloy 600 0 to 1000 °C (32
to 1832 °F)
±0.6 °C (±1.0 °F) or
±0.1%
Special
limits
T Copper/
Constantan
321 SST 0 to 350 °C (32
to 662 °F)
±0.5 °C (±1.0 °F) or
±0.4%
Special
limits
(1) Whichever is greater.
2.2 Sensor assembly
Figure 2-2: Sensor Assembly
A. Head or Field Mount Transmitters
B. Connection Heads
C. Sensor with Flying Leads, Terminal Block
Quick Start Guide April 2019
6 Rosemount 1067 Temperature Sensor
Note
Sensor assemblies can be provided without an enclosure or with an
enclosure such as the connection heads shown above or assembled to a
Rosemount transmitter.
April 2019 Quick Start Guide
Quick Start Guide 7
3 Product certifications
Rev 1.1
European Directive Information
A copy of the EU Declaration of Conformity can be found at the end of the
Quick Start Guide. The most recent revision of the EU Declaration of
Conformity can be found at Emerson.com/Rosemount.
Ordinary Location Certification
As standard, the transmitter has been examined and tested to determine
that the design meets the basic electrical, mechanical, and fire protection
requirements by a nationally recognized test laboratory (NRTL) as accredited
by the Federal Occupational Safety and Health Administration (OSHA).
North America
The US National Electrical Code
®
(NEC) and the Canadian Electrical Code
(CEC) permit the use of Division marked equipment in Zones and Zone
marked equipment in Divisions. The markings must be suitable for the area
classification, gas, and temperature class. This information is clearly defined
in the respective codes
America
E5 US Explosionproof, Dust-Ignitionproof, and Nonincendive
Certificate
FM17US0170X
Standards
FM Class 3600:2011, FM Class 3611:2004, FM Class
3615:2006, FM Class 3810:2005, ANSI/NEMA
™
250: 1991
Markings
XP CL I, DIV 1, GP B, C, D; DIP CL II/III, DIV 1, GP E, F, G; NI CL I,
DIV 2, GP A, B, C, D; T5(–50 °C ≤ T
a
≤ +85 °C); when installed
per Rosemount drawing 00068-0013; Type 4X
Canada
E6 Canadian Explosion proof and Dust-Ignition proof
Certificate
1063635
Standards
CSA C22.2 No. 0-M91; CSA C22.2 No. 25-1966; CSA C22.2 No.
30-M1986; CSA C22.2 No. 94-M91; CSA C22.2 No. 142-
M1987; CSA C22.2 No. 213-M1987
Markings
XP CL I, Div 1, GP B, C, D; DIP CL II/III, Div 1, GP E, F, G; CL I, Div
2, GP A, B, C, D; (–50 °C ≤ Ta ≤ 85 °C); when installed per
Rosemount drawing 00068-0033; Type 4X (Spring loaded
Quick Start Guide April 2019
8 Rosemount 1067 Temperature Sensor
sensors must be installed in a thermowell to maintain Type 4X
and Cl. II/III rating)
Europe
E1 ATEX Flameproof
Certificate
FM12ATEX0065X
Standards
EN 60079-0: 2012+A11:2013, EN 60079-1: 2014, EN
60529:1991 +A1:2000 + A2:2013
Markings
II 2 G Ex db IIC T6…T1 Gb; T6...T1: T
a
= -50 °C to +40 °C;
T5...T1: T
a
= -50 °C to +60 °C
Specific Conditions of Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a
source of ignition in Group III environments.
3. Guard the LCD cover against impact energies greater than 4 joules.
4. Flameproof joints are not intended for repair.
5. A suitable certified Ex db or Ex tb enclosure is required to be connected to
temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface
temperature on the equipment and the neck of DIN Style Sensor probe does
not exceed 130 °C.
7. Non-Standard Paint options may cause risk from electrostatic discharge.
Avoid installations that cause electrostatic build-up on painted surfaces, and
only clean the painted surfaces with a damp cloth. If paint is ordered through
a special option code, contact the manufacturer for more information.
ATEX Dust
Certificate
FM12ATEX0065X
Standards
EN 60079-0: 2012+A11:2013, EN 60079-31:2014, EN
60529:1991 +A1:2000+A2:2013
Markings
II 2 D Ex tb IIIC T130°C Db Ta=-40°C to +70°C; IP66
Specific Conditions of Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a
source of ignition in Group III environments.
April 2019 Quick Start Guide
Quick Start Guide 9
3. Guard the LCD cover against impact energies greater than 4 joules.
4. Flameproof joints are not intended for repair.
5. A suitable certified Ex db or Ex tb enclosure is required to be connected to
temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface
temperature on the equipment and the neck of DIN Style Sensor probe does
not exceed 130 °C.
7. Non-Standard Paint options may cause risk from electrostatic discharge.
Avoid installations that cause electrostatic build-up on painted surfaces, and
only clean the painted surfaces with a damp cloth. If paint is ordered through
a special option code, contact the manufacturer for more information.
International
E7 IECEx Flameproof
Certificate
IECEx FMG 12.0022X
Standards
IEC 60079-0:2011, 60079-1:2014-06
Markings
Ex db IIC T6…T1 Gb, T6…T1: T
a
=-50 °C to +40 °C; T5…T1:
T
a
=-50 °C to +60 °C
Specific Conditions of Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a
source of ignition in Group III environments.
3. Guard the LCD cover against impact energies greater than 4 joules.
4. Flameproof joints are not intended for repair.
5. A suitable certified Ex db or Ex tb enclosure is required to be connected to
temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface
temperature on the equipment and the neck of DIN Style Sensor probe does
not exceed 130 °C.
7. Non-Standard Paint options may cause risk from electrostatic discharge.
Avoid installations that cause electrostatic build-up on painted surfaces, and
only clean the painted surfaces with a damp cloth. If paint is ordered through
a special option code, contact the manufacturer for more information.
IECEx Dust
Certificate
IECEx FMG 12.0022X
Standards
IEC 60079-0:2011, IEC 60079-1:2013
Quick Start Guide April 2019
10 Rosemount 1067 Temperature Sensor
Markings
Ex tb IIIC T130°C Db Ta=-40°C to +70°C; IP66
Specific Conditions of Use (X):
1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a
source of ignition in Group III environments.
3. Guard the LCD cover against impact energies greater than 4 joules.
4. Flameproof joints are not intended for repair.
5. A suitable certified Ex db or Ex tb enclosure is required to be connected to
temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface
temperature on the equipment and the neck of DIN Style Sensor probe does
not exceed 130 °C.
7. Non-Standard Paint options may cause risk from electrostatic discharge.
Avoid installations that cause electrostatic build-up on painted surfaces, and
only clean the painted surfaces with a damp cloth. If paint is ordered through
a special option code, contact the manufacturer for more information.
April 2019 Quick Start Guide
Quick Start Guide 11
4 Declaration of Conformity
Figure 4-1: Rosemount 1067 Declaration of Conformity
Quick Start Guide April 2019
12 Rosemount 1067 Temperature Sensor
April 2019 Quick Start Guide
Quick Start Guide 13
5 China RoHS
ਜ਼ᴹ
China RoHS
㇑᧗⢙䍘䎵䗷ᴰབྷ⎃ᓖ䲀٬Ⲵ䜘Ԧරਧࡇ㺘
Rosemount 1067
List of Rosemount 1067
Parts with China RoHS Concentration above MCVs
䜘Ԧ਽〠
Part Name
ᴹᇣ⢙䍘Hazardous Substances
䫵
Lead
(Pb)
⊎
Mercury
(Hg)
䭹
Cadmium
(Cd)
ޝԧ䬜
ཊⓤ㚄㤟
Polybrominated
biphenyls
(PBB)
ཊⓤ㚄㤟䟊
Polybrominated
diphenyl ethers
(PBDE)
⭥ᆀ㓴Ԧ
Electronics
Assembly
O
O
O
O
O
༣փ㓴Ԧ
Housing
Assembly
O
O
O
O
O
Րᝏಘ㓴Ԧ
Sensor
Assembly
O
O
O
O
O
ᵜ㺘Ṭ㌫׍ᦞ
SJ/T11364
Ⲵ㿴ᇊ㘼ࡦ֌
This table is proposed in accordance with the provision of SJ/T11364.
O:
᜿Ѫ䈕䜘ԦⲴᡰᴹ൷䍘ᶀᯉѝ䈕ᴹᇣ⢙䍘Ⲵਜ਼䟿൷վҾ
GB/T 26572
ᡰ㿴ᇊⲴ䲀䟿㾱≲
O: Indicate that said hazardous substance in all of the homogeneous materials for this part is below the limit requirement of
GB/T 26572.
X:
᜿Ѫ൘䈕䜘Ԧᡰ֯⭘Ⲵᡰᴹ൷䍘ᶀᯉ䟼ˈ㠣ቁᴹа㊫൷䍘ᶀᯉѝ䈕ᴹᇣ⢙䍘Ⲵਜ਼䟿儈Ҿ
GB/T 26572
ᡰ㿴ᇊⲴ䲀䟿㾱≲
X: Indicate that said hazardous substance contained in at least one of the homogeneous materials used for this part is above
the limit requirement of GB/T 26572.
Quick Start Guide April 2019
14 Rosemount 1067 Temperature Sensor
April 2019 Quick Start Guide
Quick Start Guide 15
*00825-0100-4951*
Quick Start Guide
00825-0100-4951, Rev. BA
April 2019
Global Headquarters
Emerson Automation Solutions
6021 Innovation Blvd.
Shakopee, MN 55379, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
North America Regional Office
Emerson Automation Solutions
8200 Market Blvd.
Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
Latin America Regional Office
Emerson Automation Solutions
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA
+1 954 846 5030
+1 954 846 5121
[email protected]
Europe Regional Office
Emerson Automation Solutions Europe
GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
+41 (0) 41 768 6111
+41 (0) 41 768 6300
[email protected]
Asia Pacific Regional Office
Emerson Automation Solutions
1 Pandan Crescent
Singapore 128461
+65 6777 8211
+65 6777 0947
[email protected]
Middle East and Africa Regional Office
Emerson Automation Solutions
Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
+971 4 8118100
+971 4 8865465
[email protected]
Linkedin.com/company/Emerson-
Automation-Solutions
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/
RosemountMeasurement
Google.com/+RosemountMeasurement
©
2019 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are
available upon request. The Emerson logo is a
trademark and service mark of Emerson Electric
Co. Rosemount is mark of one of the Emerson
family of companies. All other marks are the
property of their respective owners.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Rosemount 1067 Temperature Sensors Quick start guide

Rosemount
Brand
Rosemount
Model
1067 Temperature Sensors
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents