Henny Penny PFE-500-CFA-FM07-016 User manual

Henny Penny
Brand
Henny Penny
Model
PFE-500-CFA-FM07-016
Type
User manual

Henny Penny PFE-500-CFA-FM07-016 is a commercial-grade deep fryer control retrofit kit designed for use with Henny Penny PFE-500-CFA fryers. This kit includes all the necessary components to upgrade your fryer's control system, including a new primary contactor, fuse holders, 24 VAC solenoid coil, and ground wire.

Upgrading your fryer's control system with the Henny Penny PFE-500-CFA-FM07-016 kit offers several benefits, including:

  • Improved temperature control for more consistent frying results
  • Reduced energy consumption through more efficient operation
  • Enhanced safety features to help prevent accidents

Henny Penny PFE-500-CFA-FM07-016 is a commercial-grade deep fryer control retrofit kit designed for use with Henny Penny PFE-500-CFA fryers. This kit includes all the necessary components to upgrade your fryer's control system, including a new primary contactor, fuse holders, 24 VAC solenoid coil, and ground wire.

Upgrading your fryer's control system with the Henny Penny PFE-500-CFA-FM07-016 kit offers several benefits, including:

  • Improved temperature control for more consistent frying results
  • Reduced energy consumption through more efficient operation
  • Enhanced safety features to help prevent accidents
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
PAGE 1-4, PROBE INSTALLATION INSTRUCTIONS
When installing the probe, use Teflon tape on the threads of reducer and compression fitting,
or peanut oil could leak into the control area.
Tighten compression nut on probe finger-tight, and then tighten ½-turn with a ½ inch wrench.
Do not over-tighten, or damage to the probe could result.
PAGE 1-5
When installing the 24 VAC solenoid coil, clean the grease build-up from the solenoid assembly.
Before installing the 2 sheets of insulation against the frypot wall, scrape any grease build-up
around the electrical components on the control compartment deck, on the side walls, and the
frypot wall, especially around the high limit and probe fittings.
PAGE 1-6 Attach ground wire, supplied in kit, to stud on control panel. See photo below
When wire tying the wires, make sure the high limit capillary tube runs under and
away from all electrical power wires. The tube must never be in contact with the
electrical power wires or terminals, or electrical shock or component damage could
result.
page 1
FM07-016
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
480 VOLT FRYERS
Step 6, page 1-2 of instructions, on 480 volt units, mark the wires that you remove from
primary contactor and fuse holders that go to the 480 to 240 stepdown transformer in
the back of the fryer. The contactor wires will be reconnected to the new primary
contactor, and the fuse wires will be reconnected to the fuse holders. It is important
that these wires be reconnected properly or damage to the control will result.
Step 5, page 1-5 of instructions,
On 480 volt units, the 480V to 240V wires must be
reconnected properly or damage to the control will result. The input voltage to the
control must not exceed 240 VAC.
Remove the wires from the L1 & L2 terminals of the primary contactor that go to the
fuses of the new contactor assembly-they are not used on 480V units.
Reconnect the
labeled wires that were disconnected in step 6C, Section 1-2, from the primary
contactor to the L1 & L2 terminals of the new primary contactor.
Reconnect the labeled wires that were disconnected from the fuse holders in step 6C,
Section 1-2, to the center terminal of the new fuse holders on the new contactor
mounting bracket.
page 2
FM07-016
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
page 3
page 3
FM07-016
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
FM07-016
page 4
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
FM07-016
page 5
IMPORTANT ADDITIONAL INFORMATION FOR
CONTROL RETROFIT INSTRUCTIONS FM01-875
FM07-016
page 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Henny Penny PFE-500-CFA-FM07-016 User manual

Henny Penny
Brand
Henny Penny
Model
PFE-500-CFA-FM07-016
Type
User manual

Henny Penny PFE-500-CFA-FM07-016 is a commercial-grade deep fryer control retrofit kit designed for use with Henny Penny PFE-500-CFA fryers. This kit includes all the necessary components to upgrade your fryer's control system, including a new primary contactor, fuse holders, 24 VAC solenoid coil, and ground wire.

Upgrading your fryer's control system with the Henny Penny PFE-500-CFA-FM07-016 kit offers several benefits, including:

  • Improved temperature control for more consistent frying results
  • Reduced energy consumption through more efficient operation
  • Enhanced safety features to help prevent accidents
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents