LG Electronics LSE3090ST User manual

Brand: LG Electronics

Model: LSE3090ST

Type: User manual

LRE3027ST

LRE3025ST

LRE3023ST

LRE3023SB

LRE3023SW

LRE3021ST

LRE3085ST

LRE3083ST

LRE3083SB

LRE3083SW

LDE3037ST

LDE3037SB

LDE3037SW

LDE3035ST

LDE3035SB

LDE3035SW

LDE3031ST

LSE3092ST

LSES302ST

www.lg.com

INSTALLATION MANUAL

ELECTRIC RANGE

Please read these instructions thoroughly before

installing and operating the range.

ENGLISH

ESPAÑOL

(REV.04 130512)

TABLE OF CONTENTS

3 SAFETY

3 Before You Begin

3 Important Safety Instructions

5 Prepare to Install the Range

6 PREPARE TO INSTALL RANGE

6 Installation Drawings

8 ELECTRICAL CONNECTIONS

8 Electrical Connection Requirements

8 Connect Range Cord

10 3-Wire Connection With a Power Supply Cord

1 1 4-Wire Connection With a Power Supply Cord

1 1 3-Wire Connection: Conduit

12 4-Wire Connection: Conduit

13 INSTALL THE RANGE

13 Anti-Tip Device Installation

13 Final Installation

13 Optional Rear Filler

ENGLISH

SAFETY

BEFORE YOU BEGIN

Remove all tape and packing materials before using the range.

Dispose of all plastic bags after unpacking the range. Never allow children to play with packing materials.

You can download the installation and owner’s manual at: http://www.lg.com.

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions before using your oven to prevent the risk of fire, electric shock, personal injury, or

damage when using the range. This guide does not cover all possible conditions that may occur. For further assistance

contact your service agent or manufacturer.

This is the safety alert symbol. This symbol alerts you to potential hazards that can cause personal injury to

you and others. All safety messages will follow the safety alert symbol with either the word “WARNING” or

“CAUTION.”

WARNING

This symbol will alert you to hazards or unsafe practices which could cause serious bodily harm or death.

CAUTION

This symbol will alert you to hazards or unsafe practices which could cause bodily injury or property damage.

• The information in this manual should be followed exactly.

- A re or electrical shock may result causing property damage, personal injury or death.

• Do not step or sit on the oven door. Install the Anti-Tip Bracket supplied with the range.

- The range could be tipped and injury might result from spilled hot liquid, food, or the range itself.

- If the range is pulled away from the wall for cleaning, service, or any other reason, ensure that the Anti-Tip de-

vice is properly reengaged when the range is pushed back against the wall.

- Install the Anti-Tip Bracket. Screws must be xed to at least two locations.

- A child or adult can be killed when the range is tipped.

- 1) According to the Anti-Tip Bracket Template, install Anti-Tip Bracket to the oor and wall.

- Anti-Tip will fasten the range by holding the range’s legs of the rear side and the Anti-Tip Bracket Template lets

you know proper locations of Anti-Tip Bracket easily.

- 2) Engage the range to the Anti-Tip Bracket by putting the range’s legs into each Anti-Tip Bracket.

- 3) Re-engage the Anti-Tip Bracket if you can move the range except for range’s front direction.

- 4) See installation instructions for details (refer to the page 13).

- Failure to do so can result in death or serious burns to children or adults.

• You should use two or more people to move and install range. (Excessive Weight Hazard)

- Failure to do so can result in back or other injury.

• You never pull or push any handles of door to move and install range.

- Failure to do so can result in serious damage to the door of the range.

• New branch-circuit installations (1996 NEC) for mobile homes, recreational vehicles, and installations

where local codes do not allow grounding through the neutral wire require a 4-conductor UL listed range

cord or 4 wire conduit connection.

WARNING

SAFETY

• Power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet

Installed by a qualied electrician.

• Using an extension cord to connect the power is prohibited. The way to connect the power cord and plug

directly is strongly recommended.

• Electrical ground is required on this appliance.

• You should make sure that the power cord is not pinched by the range or heavy objects.

- Failure to do so can result in serious burns or electrical shock.

• You never remove the protection cover covering the rear of oven.

- Failure to do so can result in serious damage to power cord. The damage causes serious burns and electric

shock.

• The middle (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be connected to the

middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be

connected to the outside posts of the main terminal connection block.

- Failure to do so can result in electrical shock, severe personal injury or death.

• Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use with

ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be used. The

middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of

the main terminal block. The other two wires of the power cord or conduit have to be connected to the

outside posts of the main terminal connection block. The 4th ground wire must be connected to the

frame of the range with the ground screw.

- Failure to do so can result in electrical shock, severe personal injury or death.

WARNING

• You should put on gloves during the installation procedure.

- Failure to do so can result in bodily injury.

• You should make sure that the wall covering, countertop and cabinets around the range can withstand

the heat (up to 194°F) generated by the range.

- Discoloration, delamination or melting may occur.

- This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194°F.

• Cabinet storage space located above the surface units should be avoided.

• You should install a range hood that projects horizontally a minimum of 5 inches beyond the bottom of

the cabinets. If cabinet Storage is to be provided.

- The risk of burns or re by reaching over the heated surface elements can be reduced.

• You should not install the range in the humid place. Splashing the range with water or any electrolyte can

result in electrical shock.

• You should not let cooking grease or ammable material accumulate in or near the range.

- Failure to do so can result in serious burns.

CAUTION

ENGLISH

SAFETY

PREPARE TO INSTALL THE RANGE

TOOLS NEEDED

Phillips Screwdriver

Pliers

Tape Measure

Pencil

” Nut Driver

Flat-blade

Screwdriver

Level

Adjustable Wrench

Safety Glasses

Gloves

Drill

PARTS PROVIDED

Template (1)

(For Anti-Tip Bracket Mounted

on Concrete Floors and Walls)

Anchor Sleeves (6)

Rear ller & 2 Screws

(LSE Series only)

Anti-Tip Bracket Kit (1)

Lag Bolts (6)

PARTS NOT PROVIDED

(UL Approved 40 or 50 AMP)

4-Wire Cord OR 3-Wire Cord

Strain Relief

(For Conduit

Installations Only)

• The information in this manual should be

followed exactly.

- A fire or electrical shock may result causing

property damage, personal injury or death.

WARNING

Tip - Over Hazard

A child or adult can tip the range and be

killed. Verify the anti-tip bracket have been

installed. Ensure the anti-tip bracket is

enganged when the range is moved.

Do not operate the range without the anti-

tip bracket in place. Failure to follow these

instructions can result in death or serious

burns to children and adults.

WARNING

To check visually that leveling leg is inserted

into bracket, grasp the top rear edge of the

range and carefully attempt to tilt it forward.

bracket

Leveling

leg

• Put on gloves during installation procedure.

- Failure to do so can result in bodily injury.

CAUTION

• Read all instructions contained in these installation

instructions before installing range.

• Remove all packing materials from the oven

compartments before connecting the electrical

supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the

consumer.

• Have the installer show you the location of the

circuit breaker or fuse. Mark it for easy reference.

NOTE

Keep these instructions with your owner’s manual

for future reference.

• As when using any appliance generating heat, there

are certain safety precautions you should follow.

• Be sure your range is installed and grounded

properly by a qualied installer or service technician.

• Make sure the wall coverings around the range

can withstand the heat generated by the range.

• To eliminate the need to reach over the surface

elements, cabinet storage space above the

elements should be avoided.

NOTE

PREPARE TO INSTALL THE RANGE

INSTALLATION DRAWINGS

SAVE FOR THE USE OF THE LOCAL ELECTRICAL INSPECTOR

NOTE

CLEARANCES AND DIMENSIONS (Figure 1)

To install range refer to the following Figure 1.

For installation in CANADA, a Free-standing range

is not to be installed closer than 15/32 (12mm) from

any adjacent surface.

• Cabinet storage space located above the

surface units should be avoided.

• Install a range hood that projects horizontally a

minimum of 5 inches beyond the bottom of the

cabinets if cabinet storage is to be provided.

- The risk of burns or fire by reaching over the

heated surface elements can be reduced.

• Make sure that the wall covering, countertop

and cabinets around the range can with-stand

the heat (up to 194°F) generated by the range.

Discoloration, delamination or melting may occur.

- This range has been designed to comply with

the maximum allowable wood cabinet tem-

peratures of 194°F.

CAUTION

FIGURE 1 FIGURE 2

A = 30”(76.2 cm) For U.S.A

= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA

• You should use two or more people to move and

install range. (Excessive Weight Hazard)

- Failure to do so can result in back or other injury.

• You never pull or push any handles of upper &

lower door to move and install range.

- Failure to do so can result in serious damage to

the door of the range.

WARNING

For model : LRE Series

ENGLISH

PREPARE TO INSTALL THE RANGE

MINIMUM DIMENSIONS (Figure 2)

* 30" (76.2 cm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood

or metal cabinet; or 24" (60.9 cm) minimum when bottom of wood or metal cabinet is protected by not less than

/4”(6.4 cm) flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" (0.381 mm) stainless

steel, 0.024" (0.610 mm) aluminum or 0.020" (0.508 mm) copper.

** 15" (38.1 cm) minimum between countertop and adjacent cabinet bottom.

24”

(60.9cm)

2.5”

(6.3cm)

6”

(15.2cm)

9”

(23cm)

9”

(23cm)

11”(28cm)

15”(38cm)

4”

(10cm)

4”

(10cm)

5”

(13cm)

Wall

Center

Cabinet

opening

2.5”(6.3cm)2.5”(6.3cm)

6”

(15.2cm)

6”

(15.2cm)

FIGURE 1

FIGURE 2

A = 30”(76.2 cm) For U.S.A

= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA

A = 30”(76.2 cm) For U.S.A

= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA

For model : LSE Series

For model : LDE Series

ELECTRICAL CONNECTIONS

ELECTRICAL CONNECTION

REQUIREMENTS

This appliance must be installed and grounded on a

branch circuit by a qualified technician in accordance

with the National Electrical code ANSI/NFPA NO. 70 -

latest edition.

All wiring should conform to Local and NEC. This range

requires a single-phase, 3 wire, A.C 120/208V or 120/240V

60Hz electrical system. Use only a 3-conductor or a

4-conductor UL-listed range cord with closed-loop

terminals, open-end spade lugs with upturned ends

or similar termination. DO NOT install the power cord

without a strain relief.

A range cord rated at 40 amps with 120/240 minimum

volt range is required. If a 50 amp range cord is used, it

should be marked for use with 1

” diameter connection

openings. This appliance may be connected by means

of conduit or power cord. If conduit is being used, go to

page 10 for 3 wire conduit connections or page 11 for 4

wire conduit connections.

• New branch-circuit installations (1996 NEC)

for mobile homes, recreational vehicles, and

installations where local codes do not allow

grounding through the neutral wire require

a 4-conductor UL listed range cord or 4 wire

conduit connection.

• Power supply cord and plug should not be

modified. If it will not fit the outlet, have a

proper outlet Installed by a qualied electrician.

• Using an extension cord to connect the power is

prohibited. The way to connect the power cord

and plug directly is strongly recommended.

• Electrical ground is required on this appliance.

• You should make sure that the power cord is

not pinched by the range or heavy objects.

- Failure to do so can result in serious burns or

electrical shock.

WARNING

Specied power-supply-cord kit rating

Range rating, watts Specied

rating of power

supply-cord kit,

amperes

Diameter (inches) of Range

connection Opening

120/240 volts

3-wire

120/208 volts

3-wire

Power cord Conduit

8,750 - 16,500

16,501 - 22,500

7,801 - 12,500

12,501 - 18,500

40 or 50A

”

3, 4 - Wire electrical wall Receptacle

4 Wire receptacle (14-50R)

3 Wire receptacle (10-50R)

FIGURE 3

CONNECT RANGE CORD

The Rear Access cover must be removed. Loosen the two

screws with a screwdriver. The terminal block will then be

accessible.

For model : LRE Series

For model : LSE Series

For model : LDE Series

Terminal block

Drawer body

Access

cover

Power cord outlet

Cord/Conduit

connection

plate

Terminal block

Drawer body cover

(LSE series only)

Drawer body

Access cover

Cord/Conduit

connection plate

Power cord outlet

FIGURE 4

Terminal block

Rear of lower oven

Access

cover

Access cover

Cord/Conduit

connection

plate

Protection cover

ENGLISH

ELECTRICAL CONNECTIONS

The Cord/Conduit connection plate is used for the

installation of power cord or conduit. For power cord,

install it with the connection plate as INSTALLED. For

conduit, remove the connection plate and use the conduit

hole (1

”) instead of power cord hole (1

” ). (Refer to

Figure 5 and 6.)

• You never remove the protection cover

covering the rear of lower oven.

- Failure to do so can result in serious damage to

power cord. The damage causes serious burns

and electric shock.

WARNING (LDE series only)

For model : LRE Series For model : LSE Series For model : LDE Series

"(3.5cm)

"(Cord) 1

"(Conduit)

"(2.8cm)

Remove the Conduit connection plate

FIGURE 5

FIGURE 6

Reinstall the Cord/Conduit connection plate

Strain relief

Conduit

Ring

Cord Strain relief

Conduit

Body

Cord/conduit

connection

plate

Cord Strain

relief

Cord/Conduit

connection

plate

"(3.5cm)

(Cord)

(Conduit)

"(2.8cm)

"(3.5cm)

(Cord)

" (Conduit)

"(2.8cm)

Cord Strain

relief

Conduit

Cord/Conduit

connection

plate

ELECTRICAL CONNECTIONS

3-WIRE CONNECTION WITH

A POWER SUPPLY CORD

• The middle (neutral or ground) wire, which

is white, of a 3 wire power cord or a 3 wire

conduit has to be connected to the middle

post of the main terminal block. The remaining

two wires of the power cord or conduit have to

be connected to the outside posts of the main

terminal connection block.

- Failure to do so can result in electrical shock,

severe personal injury or death.

WARNING

Install the power cord as follows:

For power cord installations, Hook the strain relief over

the power cord hole (1

”) located below the rear of

oven. Insert the power cord through the strain relief and

tighten it. (Refer to Figure 7.)

DO NOT install the power cord without a strain relief.

1. Remove the lower 3 screws from the terminal block

and retain them. (Refer to Figure 8.)

2. Insert the 3 screws through each power cord terminal

ring and into the lower terminals of the terminal block.

Make sure that the center (neutral) wire, which is

white, is connected to the center lower position of the

terminal block.

3. Tighten 3 screws securely into the terminal block. Do

not remove the ground strap connections.

4. Refer to page 13

Cord strain relief

Power cord

Conduit

connection

plate

Separate Strain Relief

before installation

Assemble the strain relief

to the 1

” opening in

Conduit connection plate

FIGURE 7

3-wire connection

Terminal

block

Conduit

connection plate

Black White Red

FIGURE 8

* If screws are not tightened securely, it can result in

electrical spark and severe personal injury or death.

ENGLISH

ELECTRICAL CONNECTIONS

4-WIRE CONNECTION WITH

A POWER SUPPLY CORD

•

Only a 4-conductor power-supply cord kit rated

120/240 volts, 50 amperes and marked for use

with ranges with closed-loop connectors or open-

end spade lugs with upturned ends shall be used.

The middle (neutral) wire, which is white, of the

power cord or 4-wire conduit has to be connected

to the middle post of the main terminal block.

The other two wires of the power cord or conduit

have to be connected to the outside posts of the

main terminal connection block. The 4th ground

wire (green) must be connected to the frame of

the range with the ground screw.

- Failure to do so can result in electrical shock,

severe personal injury or death.

WARNING

Install the power cord as follows:

For power cord installations, Hook the strain relief over

the power cord hole (1

”) located below the rear of

oven. Insert the power cord through the strain relief and

tighten it. (Refer to Figure 7.)

DO NOT install the power cord without a strain relief.

1. Remove the lower 3 screws from the terminal block

and retain them. (Refer to Figure 9.)

2. Remove ground strap and discard as show in in

Figure 9.

Insert the ground screw into the power cord ground wire

(green) terminal ring and secure it to the range frame.

Insert the 3 screws through each power cord terminal ring

and into the lower terminals of the terminal block. Make sure

that the center (neutral) wire, which is white, is connected to

the center lower position of the terminal block.

5. Tighten 3 screws securely into the terminal block.

4-wire connection

Terminal

block

Conduit

connection plate

Ground screw

Remove ground

strap and discard

Ground

strap

Black White Red

FIGURE 9

3-WIRE CONNECTION: CONDUIT

Install the conduit as follows:

Remove the Conduit connection plate from the rear of

oven and rotate it as shown in Figure 5. The conduit hole

") must be used.

First, prepare the conduit wires as shown in Figure 10.

3 wire 4 wire

Conduit

connection

plate

Ground

wire

FIGURE 10

Second, install conduit as shown in Figure 6.

For conduit installations, after purchasing a strain relief,

insert it in the conduit hole (1

”). Then install the

conduit through the body of strain relief and fasten the

strain relief with its ring. Reinstall the bracket.

For conduit connections :

If the wire in the conduit is copper it must be 8 or 10

AWG wiring.

If the wire in the conduit is aluminum it must be 6 or 8

AWG wiring.

1. Loosen the lower 3 screws from the terminal block.

Refer to Figure 11.)

2. Insert the bare wire (white/neutral) end through the

center terminal block opening. Do not remove ground

strap connections.

3. Insert the two side bare wire ends into the lower left

and the lower right terminal block opening. Tighten

the 3 screws securely into the terminal block.

(approximately 35 - 50 IN-LB)

4. Refer to page 13.

3-wire connection

Terminal

block

Wire ends

Conduit

connection plate

Black White Red

FIGURE 11

* If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

ELECTRICAL CONNECTIONS

4-WIRE CONNECTION: CONDUIT



















- Failure to do so can result in electrical shock,

severe personal injury or death.

WARNING

1. Follow the instructions under “Install the conduit as

follows” on page 11 to correctly install the strain relief.

DO NOT install the conduit without a strain relief.

2. Loosen the 2 lower left and right screws from the

terminal block. (Refer to Figure 12.) Remove the lower

2 center screws.

3. Remove ground strap and discard as shown in Figure

12. Do not discard any screws.

4. Attach the ground bare wire (green) end to range

frame and secure it in place with the ground screw

(Refer to figure 12.)

5. Insert the bare wire (white/neutral) end through the

center terminal block opening.

6. Insert the two side bare wire ends into the left and the

right terminal block opening. Tighten the 3 screws

securely into the terminal block. (approximately

35 - 50 IN-LB)

7. Refer to page 13.

4-wire connection

Remove

ground

strap and

discard

Terminal

block

Wire

ends

Conduit

connection plate

Black White Red

Ground

strap

Ground

Wire

Ground

Screw



* If screws are not tightened securely, it can result in

electrical spark and severe personal injury or death.

Replace the access cover on the back of the range. To

replace the wire cover, insert the two tabs into the

openings located below the opening and tighten the

three screws.

Access cover

ENGLISH

INSTALL THE RANGE

ANTI-TIP DEVICE INSTALLATION

Tip - Over Hazard

A child or adult can tip the range and be

killed. Verify the anti-tip bracket have been

installed. Ensure the anti-tip bracket is

enganged when the range is moved.

Do not operate the range without the anti-

tip bracket in place. Failure to follow these

instructions can result in death or serious

burns to children and adults.

WARNING

To check visually that leveling leg is inserted

into bracket, grasp the top rear edge of the

range and carefully attempt to tilt it forward.

bracket

Leveling

leg

Anti-tip

bracket

Wall plate

Screw must

enter wood

or concrete

1. Locate the bracket using the template

Anti-tip bracket are packaged with the template. The

instructions include necessary information to

complete the installation. Read and follow range

installation instruction sheet (template).

2. Level the range

Level the range by adjusting the leveling legs with a

wrench.

Leg

leveler

Raise

range

Lower

range

Use a level to check your adjustments. Place the level

diagonally on the oven rack, and check each direction

for level.

First check direction .

After check direction .

If the level doesn’t show

level on the rack, adjust

the leveling legs with a

wrench.

FINAL INSTALLATION

• Move range close enough to the opening to plug into

the receptacle.

• Slide range into position insuring that both back legs

slide under the anti-tip bracket. Range should sit flush

against the back wall when properly installed.

• Carefully attempt to tip range forward to insure that

the anti-tip bracket is engaged properly. If properly

installed, the anti-bracket will prevent the range from

being tipped. If the range can be tipped, reinstall the

range until the bracket is properly installed and the

range will not tip forward.

• Turn on electrical power. Check the range for proper

operation as described in owner’s manual.

OPTIONAL REAR FILLER

If the counter does not bridge the opening at the rear

wall the rear filler kit, that is provided with the slide in

range, will be needed.

If the countertop depth is greater than 25” there will

be a gap between the ller kit and the back wall.

NOTE

If the countertop depth is less than 24”, the control panel

will not sit ush with the countertop.

(See gure 1 on page 6)

level

LG Electronics LSE3090ST User manual

LG Electronics LSE3090ST User manual

LG Electronics LSE3090ST User manual

Related papers

Other documents