Bush Bluetooth DAB Radio User manual

Brand: Bush

Model: Bluetooth DAB Radio

Category: Radios

Type: User manual

This manual is also suitable for

Instruction Manual

DAB/FM Radio with Bluetooth

Important safety information..................... 3

Instructions for use ........................................ 5

Check the package contents ............ 5

Where to put your Radio ..................... 5

Setting up .................................................. 5

Time and date ......................................... 6

Using headphones ................................ 6

DAB/FM Radio with Bluetooth .................. 7

Front ............................................................ 7

Rear ............................................................. 7

Using your Bluetooth DAB Radio ............. 8

Switch on .................................................. 8

Switch o .................................................. 8

Change the mode ................................. 8

Adjusting the volume ........................... 8

Using the DAB radio ...................................... 9

Telescopic aerial ..................................... 9

DAB Radio mode.................................... 9

Changing DAB stations ........................ 9

Scanning for DAB stations .................. 9

Prune DAB stations................................ 10

Storing a DAB station preset .............. 10

Tune to a DAB preset station ............. 10

DAB display information ..................... 11

Dynamic range control (DRC) ........... 12

Using the FM radio ......................................... 13

Telescopic aerial ..................................... 13

FM Radio mode ...................................... 13

Tuning to an FM station ....................... 13

Changing the Scan setting ................. 13

Audio mode ............................................. 14

Storing an FM station preset .............. 14

Tune to an FM preset station ............. 14

FM display information ........................ 15

Bluetooth mode ............................................. 16

Bluetooth (BT) mode ............................ 16

Connecting or ‘Pairing’ with your

Radio ........................................................... 16

Listening to Music/Audio using

Bluetooth .................................................. 16

Set the time and date ................................... 18

Setting the time and date ................... 18

Setting the alarm .................................... 18

Stop the Alarm ....................................... 19

Snooze ...................................................... 20

Turn o the Alarm ................................. 20

Sleep timer .............................................. 20

Cancel the Sleep timer ....................... 20

System settings ............................................... 21

Display backlight timeout ................... 21

Display language ................................... 21

Software version ..................................... 22

Factory reset ............................................ 22

Technical information .................................. 23

Troubleshooting ............................................. 24

General information ...................................... 26

Product guarantee ......................................... 27

DAB/FM Radio with Bluetooth

Contents

Your Radio should be treated with care. The information below has been provided in

the interest of safety and will help you to enjoy this product and the beneﬁts it brings

for many years.

• Keep the product and all its parts out of reach of small children.

• This product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning the use of the

appliance by a person responsible for their safety.

• Keep it dry. Avoid exposure to precipitation, humidity and liquids which could all

aect the product circuitry.

• Do NOT leave it in high temperatures as electronic devices and plastic parts may

warp in heat.

• Do NOT leave it in low temperatures as moisture can form inside the product,

which may damage the circuit board.

• Do NOT block or cover slots, holes or openings on the product by placing on soft

furnishings such as carpets, rugs or beds as these are provided for functionality

and/or ventilation to ensure safe operation of the product

• Do NOT store in dusty or dirty areas.

• Do NOT use harsh chemicals, cleaning solvents or detergents to clean the

product. Wipe with a damp (not wet) soft cloth to clean.

• Disconnect your Radio from the mains power supply during thunderstorms.

• Always check that you have completely switched o your Radio, before you

change or disconnect the power supply.

• Only use the power supply that came with the product. Using an unauthorised

power supply will invalidate your guarantee and may irrecoverably damage the

product.

• Where the mains power plug or an appliance coupler is used as the disconnect

device, the disconnect device shall remain readily operable.

• Do NOT attempt to open the product. This product does not contain any user

serviceable parts. Unauthorised handling of the device may damage it and will void

your warranty.

• Do NOT use your Radio near emergency/intensive care medical equipment; if you

have a pacemaker ﬁtted or during an electrical storm.

• If the Radio will not be used for a long period of time, make sure that all of the

batteries are removed from the battery compartment and the mains power is

unplugged.

Important safety information

• Only use recommended batteries or those of the same equivalent type.

• Do not mix old and new batteries or batteries of dierent types.

• Batteries are to be inserted with the correct polarity.

• The supply terminals are not to be short-circuited.

• Remove the batteries from the Radio if they will not be used for an extended

period of time.

• Do not attempt to recharge non-rechargeable batteries.

• Dispose of old batteries carefully.

• Never throw batteries in a ﬁre or attempt to open the outer casing.

• Batteries are harmful if swallowed, so keep away from young children.

• CAUTION: Danger of explosion if batteries are incorrectly replaced. Replace only

with the same or equivalent type.

WARNING:

To prevent possible hearing damage, do not listen to this radio at high volume levels

for long periods of time.

Check the package contents

The package contains:

• 1 x DAB/FM Radio with Bluetooth

• 1 x Mains adaptor

• 1 x Instruction manual

Where to put your Radio

It is important that you consider carefully in advance where your radio will be situated

and make sure that it is:

• on a ﬂat and stable surface

Note: Never place your radio directly onto antique or polished surfaces.

• within 1.5 metres of a power socket. Please ensure that the mains power lead and

speaker cables are not a trip hazard.

• at least 1 metre away from other electrical appliances to avoid interference

• where it will be in range of the connected or ‘paired’ bluetooth device (e.g. iPod/

iPhone/iPad/Android/other phone/Computer), which is about 10 metres or less (33

feet or less) in line of sight.

• where you can fully extend the telescopic radio aerial

• away from bright sunlight or heat sources, such as a radiator

• not in a humid or very damp place such as a bathroom

Setting up

1. Connect the mains power lead into the socket on the back of the radio and fully

extend the telescopic aerial in a vertical position to obtain the maximum signal

strength.

2. Plug the power adaptor into the mains power wall socket and switch on.

3. Slide the switch on the back of the radio to ‘On’. The display will light up and

‘Welcome to Digital Radio’ will be displayed.

4. Press and release the ‘Power’ button on the front of the radio. Your radio will

switch on and begin an automatic scan for DAB radio stations. A progress bar will

show the progress of the scan and the number of stations found during the scan

will also be displayed.

When the scan is complete your radio will select the ﬁrst available station and

begin to play. Stations are listed in numerical and then alphabetical order by

default.

Instructions for use

Note: The DAB radio station list is stored in the memory and so the next time you

switch your radio on, the station search does not take place. It is possible to scan

manually for stations. Please see page 9.

5. Inserting the batteries (optional). Before installing the batteries (not included)

please ensure that the radio is switched o (slide the power switch on the back to

o) and is unplugged from the mains power supply.

On the back of the radio, push down the two tabs to release and remove the

battery compartment cover.

Insert 4 x 1.5V C-size (also known as LR-14) batteries, making sure to note the ‘+’

and ‘-‘ markings and position the batteries the correct way around.

Replace the battery cover, making sure it ‘clicks’ shut.

If used continuously on battery power, your radio has an approximate battery life

of 5 hours when using good quality alkaline batteries. When the battery power is

low, please switch o the radio and replace the batteries.

For battery operation, please switch o the mains adaptor and remove the mains

power plug from the back of the radio.

Time and date

The ﬁrst time you listen to DAB radio, the time and date of your product will be

synchronised automatically to that broadcast by the DAB service in 24 hour mode;

which is in line with daylight saving, so there is no need to set the time and date

manually.

If you do wish to set the time and date manually, please see page 18.

Using headphones

You can connect headphones with a 3.5mm plug (not included) to your radio. The

stereo headphone socket can be found on the back of the radio at the bottom. When

you have headphones connected the radio speakers are switched o and all sound is

via the headphones.

Note: Always keep the volume within reasonable limits.

DAB/FM Radio with Bluetooth

Front

Power On/O

(standby)

Menu/Info

Skip back

Mode

Handle Display

Speaker

Volume control

Scan

Preset

Snooze

Skip forward

Play/Pause

Speaker

Tune/Select

Rear

Aerial

Battery compartment

4 x 1.5V C-size (LR-14)

batteries (not supplied)

Power socket

Headphone socket

Power On/O

switch

Switch on

Press and release the ‘Power’ button on the front of your radio. The display will fully

switch on and your radio will return to the mode that it was last used in (DAB/FM/BT).

If you were listening to a radio station when you turned the radio o, then this station

will be automatically selected.

Note: Always make sure that the aerial is fully extended, to ensure the maximum signal

strength and the best possible sound quality.

Switch o

Press and release the ‘Power’ button on the front of your radio. The radio will go into

Standby mode.

To completely switch o the radio and the display, slide the switch on the back of the

radio to ‘O’ and switch o the mains power at the wall socket. Remove the batteries,

if ﬁtted.

Note: If you do not use your radio for approximately 15 minutes and no audio signal

is received, it will automatically go to Standby mode. Press and release the ‘Power’

button and the radio will return to the mode that it was last used in.

Change the mode

Press and release the ‘Mode’ button to change between DAB, FM and Bluetooth

modes. Please check the display, which will conﬁrm the mode.

Adjusting the volume

Turn the rotary volume control anti-clockwise to decrease the volume and clockwise

to increase the volume. When you adjust the volume, please check the display which

will conﬁrm the volume setting.

Using your Bluetooth DAB Radio

Telescopic aerial

Please make sure that the aerial is fully extended before you attempt to tune to a DAB

station (a vertical position is recommended). This will ensure that the maximum signal

strength is available when the radio begins to scan. Extending the aerial also ensures

the best possible sound quality.

DAB Radio mode

Check that your radio is in DAB mode. If you are not already in DAB mode, press and

release the ‘Mode’ button to go to DAB mode (check the display).

The ﬁrst time you use the radio or if the station list is empty, your radio will

automatically begin to scan for DAB radio stations. A progress bar will show the

progress of the scan and the number of stations found during the scan will also be

displayed.

If you were listening to a DAB station when you switched the radio o then this station

will be automatically selected when you switch the radio back on.

Changing DAB stations

In DAB mode:

1. Turn the rotary ‘Tune’ control on the front of the radio to scroll through the

available stations.

2. When the station that you would like to listen to is displayed press to ‘Select’. There

will be a short delay whilst your radio tunes to your selected station.

Scanning for DAB stations

With DAB radio, additional stations and services regularly become available so it’s a

good idea to carry out a manual scan every now and then to make sure that you have

the most up to date station listing stored within the memory of your radio. If you have

moved your radio to another location e.g.: if you go on holiday, then it’s also a good

idea to carry out a manual scan.

If you are not already in DAB mode, press and release the ‘Mode’ button to go to DAB

mode.

1. Press the ‘Scan’ button to begin a search for stations. The display will change to

‘Scanning...’ A progress bar will show the progress of the scan and the number of

stations found during the scan will also be displayed.

Using the DAB radio

Prune DAB stations

You can remove the DAB stations in the station list that cannot be received in your

area. These are listed with a ‘?’ preﬁx.

1. Press and hold the ‘Menu/Info’ button until the display changes to

‘DAB <Full Scan>’ and use the ‘Tune/Select’ rotary control to scroll to ‘Prune’.

Press the ‘Tune/Select’ rotary control to select.

2. ‘Prune ? <No> Yes’ is displayed. Use ‘Tune/Select’ rotary control to scroll to ‘Yes’.

Press the rotary control to select and prune the station list. Stations with a ‘?’ preﬁx

will now no longer be displayed. Press the ‘Menu/Info’ button to return to the

station display.

Storing a DAB station preset

Your radio can store up to 10 DAB stations in its preset memories for instant access to

your favourite stations.

Note: When you store DAB radio station presets, these do not overwrite your FM

station presets.

1. Tune your radio to the station that you wish to preset (see changing DAB stations

on page 9).

2. Press and hold the ‘Preset’ button on the front of your radio. ‘Preset Store

<1: (Empty) >’ is displayed if no previous station has been stored.

3. Use the ‘Tune/Select’ rotary control to scroll to the Preset location that you would

like to store the radio station to (1-10).

4. Press the ‘Tune/Select’ rotary control to select, the display will conﬁrm ‘Preset X

stored’, where ‘X’ is the number of the preset (1-10).

Note: If there is already an existing DAB station stored under a preset, it will be

overwritten when you store the new station.

Tune to a DAB preset station

In DAB mode:

1. Press and release the ‘Preset’ button. ‘Preset Recall <1: >’ is displayed and the

name or frequency of the station stored there, or ‘(Empty)’ if no previous station

has been stored.

2. Use the ‘Tune/Select’ rotary control to scroll to the Preset location and station that

you would like to listen to (1-10). Press and release the ‘Tune/Select’ rotary control

to ‘Select.’ The radio will instantly tune to that station and begin to play.

Note: If no DAB station has been stored under the preset button, ‘Preset Empty’ will

be displayed and the radio will revert to the previously selected radio station.

DAB display information

When listening to a DAB station you can change the information that will appear on

the second line of the display. There are several dierent types of information that are

sent by the broadcaster.

• Dynamic Label Segment (DLS)

This is scrolling text information supplied by the broadcaster. Information could be

the name of an artist or music title, DJ’s name, contact details for the radio station

etc.

• Signal Strength

An empty will appear on the second line of the display to indicate the minimum

signal strength for acceptable listening. The row of solid rectangles indicate the

actual signal strength that you are receiving. The stronger the signal, the further to

the right the row of solid rectangles will be.

• Program Type (PTY) - such as ‘Rock’, ‘Pop‘, Talk’ or ‘News’

• Multiplex Name - displays the broadcasting area and collection of radio stations on

this frequency e.g.: BBC National DAB, Digital 1 Network.

• Channel and Frequency

e.g.: 12B 225.648 MHz

• Signal information

The data rate at which the signal is being transmitted.

Signal error

This is displayed as a number between 0-99. It would not be possible to

satisfactorily listen to a ratio station with a signal error rate of 30 or above. Try

adjusting the aerial or relocating your radio to improve reception.

• Time and date

Supplied by the broadcaster.

1. Repeatedly press and release the ‘Menu/Info’ button on the front of the radio to

cycle through the dierent information options.

Dynamic range control (DRC)

In DAB mode:

The dynamic range for each radio programme is set by the broadcaster for each radio

station and may be dierent for the types of programme broadcast, such as pop or

classical music or a chat show. The dynamic range control signal is transmitted in

parallel with the audio signal for each programme and with your radio you can use this

control signal to expand or compress the dynamic range (the dierence between the

loudest and quietest sounds) of the reproduced audio signal. Changing the dynamic

range can aect the ‘loudness’ and/or ‘quality of sound’ of the programme that you

hear so that it will be more suited to your listening conditions and your own personal

listening requirements. e.g. in a noisy environment, where quiet sounds might be

swamped, setting the compression to maximum will ‘boost’ the quiet sounds, whilst

keeping the loudest sounds at their original level.

There are 3 levels of compression:

• DRC O: no compression. This is the default setting.

• DRC Low: medium compression.

• DRC High: maximum compression.

1. Press and hold the ‘Menu/Info’ button until the display changes to

‘DAB <Full scan>’.

2. Use the ‘Tune/Select’ rotary control to scroll to ‘DRC’ and press to select. The

current DRC setting will have an ‘*’ in the top right of the display.

3. Use the ‘Tune/Select’ rotary control to scroll through the 3 compression level

options available and press the rotary control to select. Press and release the

‘Menu/Info’ button to return to the station display.

Telescopic aerial

Please make sure that the aerial is fully extended before you attempt to tune to an FM

station. This will ensure that the maximum signal strength is available when the radio

begins to scan. Extending the aerial also ensures the best possible sound quality.

FM Radio mode

If you are not already in FM mode, brieﬂy press and release the ‘Mode’ button to go to

FM mode (check the display).

If you were listening to an FM station when you switched the Radio o then this station

will be automatically selected when you switch the Radio back on.

Tuning to an FM station

Press and release the ‘Scan’ button on the front of your radio to scan up the frequency

band.

Use the left hand rotary control to ﬁne tune each frequency in 0.05MHz steps.

Note: If reception is still poor adjust the position of the aerial or try moving the radio to

another location.

Changing the Scan setting

In FM mode:

Press and hold the ‘Menu/Info’ button until ‘FM Scan setting’ is displayed. Press the

‘Tune/Select’ rotary control to select. The current Scan setting will have an ‘*’ in the

top right of the display.

There are two dierent options to choose from:

• Strong stations

The scan will only stop when a strong signal strength is received which should also

result in a better audio quality. It is possible that the station you are scanning for

may be missed using this option.

• All stations

The scan will stop for every station it receives, even if the signal strength is poor.

Use the ‘Tune/Select’ rotary control to choose from the two options available and

press to select. Press and release the ‘Menu/Info’ button to return to the station

display.

Using the FM radio

Audio mode

The radio will automatically switch between Stereo and Mono, depending on the

quality of the signal being received but you can override this function and manually

switch between ‘Stereo’ and ‘Mono’.

Note: You may wish to select ‘Stereo’ if you are listening to your radio using

headphones.

1. Press and hold the ‘Menu/Info’ button on the front of the radio until ‘FM <Scan

setting>’ is displayed.

2. Use the ‘Tune/Select’ rotary control to scroll to <Audio setting>. Press the ‘Tune/

Select’ rotary control to select.

There are now two dierent options of ‘Forced mono’ and ‘Stereo allowed’ and the

current setting will have an ‘*’ next to it.

3. Use the ‘Tune/Select rotary control to scroll to choose from the two options

available. Press the ‘Tune/Select’ rotary control on the radio to select.

4. Press and release the ‘Menu/Info’ button to return to the station display.

Storing an FM station preset

Your radio can store up to 10 FM stations in its preset memories for instant access to

your favourite stations.

Note: When you store FM radio station presets, these do not overwrite your DAB

station presets.

1. Tune your radio to the station that you wish to preset (see Tuning to an FM station

on page 13).

2. Press and hold the ‘Preset’ button on the front of your radio. ‘Preset Store

<1: (Empty) >’ is displayed if no previous station has been stored.

3. Use the ‘Tune/Select’ rotary control to scroll to the Preset location that you would

like to store the radio station to (1-10).

4. Press the ‘Tune/Select’ rotary control to select, the display will conﬁrm ‘Preset X

stored’, where ‘X’ is the number of the preset (1-10).

Note: If there is already an existing FM station stored under a preset, it will be

overwritten when you store the new station.

Tune to an FM preset station

In FM mode:

1. Press and release the ‘Preset’ button. ‘Preset Recall <1: >’ is displayed and the

name or frequency of the station stored there, or ‘(Empty)’ if no previous station

has been stored.

2. Use the ‘Tune/Select’ rotary control to scroll to the Preset location and station that

you would like to listen to (1-10). Press and release the ‘Tune/Select’ rotary control

to ‘Select.’ The radio will tune to that station and begin to play.

Note: If no FM station has been stored under the preset button, ‘Preset Empty’ will

be displayed and the radio will revert to the previously selected radio station.

FM display information

When listening to an FM station you can change the information that will appear on

the second line of the display.

• Radiotext (RT)

This is scrolling text information supplied by the broadcaster. Information could be

the name of an artist or music title, DJ’s name, contact details for the radio station

etc.

• Program Type (PTY)

Such as ‘Rock’, ‘Pop‘, Talk’ or ‘News’

• Station name or frequency

Such as BBC R4 or 93.30MHz

1. Repeatedly press and release the ‘Menu/Info’ button on the front of the radio to

cycle through the dierent information options.

Bluetooth (BT) mode

Check that your Radio is in Bluetooth (BT) mode. If you are not already in BT mode,

press and release the ‘Mode’ button on the front of the radio until you are in BT mode

(check the display). A tone will sound and ‘Bluetooth’ will be displayed, following by

‘Searching’, whilst your product searches for Bluetooth devices. If a device is already

connected (paired) with your radio, ‘Connected’ will be displayed on the second line of

the display.

Connecting or ‘Pairing’ with your Radio

In Bluetooth (BT) Mode:

1. ‘Searching’ will ﬂash on the second line of the display.

2. On the device that you would like to connect to your radio via Bluetooth

(e.g. iPhone/iPad/Android/other phone/Tablet/Computer), turn on Bluetooth

connectivity and ensure that it is ‘discoverable’.

Note: If necessary, refer to the instructions for your device to add or set up

Bluetooth.

3. Select to ‘Add new device’, if necessary.

Note: Some products will automatically search for a new device and so the ‘Add

new device’ option is not available.

4. When found, your radio will be displayed as ‘BUSH BT DAB’. Select the device

name to begin pairing.

5. When pairing is complete ‘Searching’ will stop ﬂashing in the display and

‘Connected’ will be displayed.

6. Now that you have paired your device with the radio, it will connect to it when it is

within range, which is about 10 metres or less (33 feet or less), line of sight.

7. Your device will remain paired with the radio unless you decide to disconnect or

‘unpair’ it.

Note: If your device should be come unpaired for any reason, follow the steps

above to ‘pair’ it again.

You can press and hold the on the Radio to restart the Bluetooth pairing

process.

Listening to Music/Audio using Bluetooth

In Bluetooth mode:

1. Select and start the music or audio that you wish to listen to on your paired

Bluetooth device, it will now be heard through the radio speakers. Adjust the

volume on the connected device and/or your radio

Bluetooth mode

Note:

If your previously paired device is within range but does not automatically connect,

go to the Bluetooth connectivity settings on your device and select ‘BUSH BT DAB’

to reconnect.

2. You can use the controls on your paired Bluetooth device as well as those on the

front of the radio.

Controls available on your Radio:

• Volume:

Turn the volume control clockwise to increase sound and anti-clockwise to

decrease sound.

• Play/Pause:

Press and release to play/pause.

• Skip back:

Press and release to skip back to the previous track.

• Skip forward:

Skip forward. Press and release to skip forward to the next track.

Note: If you do not use your radio for approximately 15 minutes and no audio

signal is received, it will automatically go to Standby mode. Press and release the

‘Power’ button and the radio will switch back on.

Setting the time and date

The ﬁrst time you listen to DAB radio, the time and date of your product will be

synchronised automatically to that broadcast by the DAB service in 24 hour mode;

which is in line with daylight saving, but you can set the time and date manually.

In DAB mode:

1. Press and hold the ‘Menu/Info’ button until ‘DAB <Full scan>’ is displayed.

2. Use the ‘Tune/Select’ rotary control to scroll to ‘<System>’. Press the ‘Tune/Select’

rotary control to select.

3. Use the ‘Tune/Select’ rotary control to scroll to ‘<Time>’. Press the ‘Tune/Select’

rotary control to select. ‘<Set Time/Date>’ is displayed. Press the ‘Tune/Select’

rotary control to select.

4. ‘Set time’ is displayed and the hour digits will ﬂash. Use the ‘Tune/Select’ rotary

control to scroll to the correct hour. Press the ‘Tune/Select’ rotary control to

select.

5. The minutes will now ﬂash. Use the ‘Tune/Select’ rotary control to scroll to the

correct minutes. Press the ‘Tune/Select’ rotary control to select.

6. ‘Set date ’ is displayed and the day will ﬂash. Use the ‘Tune/Select’ rotary control

and press to select to set the day, month and year, using the same method as you

did to set the time.

When you conﬁrm the correct date, ‘Time Saved’ is displayed and the display

returns to <Set Time/Date>’.

You can now use the ‘Tune/Select’ rotary to scroll and the same method as you did to

set the time and date to change the settings for:

• 12/24 hour clock display

• The date format, DD-MM-YYYY or MM-DD-YYYY

• To auto update the time from the DAB signal, FM signal, DAB or FM signal or no

update.

Setting the alarm

Note: Check that the radio has the correct time and date before you set an alarm.

In DAB or FM mode:

1. Press and hold the ‘Menu/Info’ button to enter the menu options..

2. Use the ‘Tune/Select’ rotary control to scroll to ‘<System>’. Press the ‘Tune/Select’

rotary control to select.

3. Use the ‘Tune/Select’ rotary control to scroll to ‘<Alarm 1>’ or ‘<Alarm 2> as

required. Press the ‘Tune/Select’ rotary control to select.

4. ‘Alarm 1 (or 2) Setup’ is displayed. Press the ‘Tune/Select’ rotary control to select.

Set the time and date

5. ‘Alarm 1 (or 2) Wizard On time’ is displayed and the hour digits for the alarm will

ﬂash.

6. Use the ‘Tune/Select’ rotary control to scroll to the hour for the alarm and press

the ‘Tune/Select’ rotary control to select.

7. The minutes will now ﬂash. Use the ‘Tune/Select’ rotary control to scroll to the

minutes for the alarm and press the ‘Tune/Select’ rotary control to select. The

duration time will now ﬂash.

8. Use the ‘Tune/Select’ rotary control to scroll to the duration for the alarm. You can

choose from 15, 30, 45, 60 and 90 minutes. Press the ‘Tune/Select’ rotary control

to select. The source for the alarm will now ﬂash.

9. Use the ‘Tune/Select’ rotary control to scroll to the sound source for the alarm.

You can choose from Buzzer, DAB or FM. Press the ‘Tune/Select’ rotary control to

select.

Note: If you select DAB or FM radio for the alarm source, ‘Last listened’ will ﬂash in

the display. Press the ‘Tune/Select’ rotary control to select and the last listened to

radio station in DAB or FM, as appropriate, will be used for your alarm.

10. Use the ‘Tune/Select’ rotary control to scroll to the frequency for the alarm. You

can choose from Daily, Once, Weekends or Weekdays. Press the ‘Tune/Select’

rotary control to select.

Note: If you select ‘Once’, you will then be prompted to set the date for your

alarm.

11. Use the ‘Tune/Select’ rotary control to set the volume for your alarm. Press the

rotary ‘Tune/Select’ control to select.

Note: Remember to set the alarm radio volume to one that will wake you. The

alarm volume will increase progressively until it reaches the alarm volume you

have set.

12. ‘Alarm 1 Wizard’ is displayed again, together with ‘Alarm O (or On)’. Use the ‘Tune/

Select’ rotary control to choose ‘Alarm On’ or ‘O’ and press the ‘Tune/Select’

rotary control to select. ‘Alarm Saved’ is displayed.

13. In Standby mode a bell symbol in the top right of the display, together with the

digit ‘1’ or ‘2’ as appropriate, will conﬁrm when an alarm has been set.

Note: If the time is not set or has failed to update from the radio signal, ‘Time is not

set’ will be displayed when you try to set the alarm. The radio will then prompt

you to set the time. An alarm can only be set after the time has been set.

Stop the Alarm

When the alarm sounds, press and release the ‘Power’ button, ‘Alarm o’ is displayed.

Alternatively, you can press and release the ‘Snooze’ button (see Snooze function

below).

Note: If you press the ‘Power’ button to stop the alarm, the alarm symbol will remain in

the display and the alarm will sound again at the same time the next day, unless it was

set for ‘Once’ only.

Snooze

When the alarm sounds you can press and release the ‘Snooze’ button. ‘Snooze 5

minutes’ will be displayed, followed by the snooze time countdown, until the alarm

sounds again.

Turn o the Alarm

Follow the steps for ‘Setting an Alarm’ and select ‘O’ in step 12.

Sleep timer

You can set your radio to turn o automatically using the sleep timer. You can choose

from Sleep o, 15, 30, 45, 60 and 90 minutes.

In DAB or FM mode:

1. Press and hold the ‘Menu/Info’ button to enter the menu options.

2. Use the ‘Tune/Select’ rotary control to scroll to ‘System’. Press the ‘Tune/Select’

rotary control to select.

3. Use the ‘Tune/Select’ rotary control to scroll to <Sleep>. Press the ‘Tune/Select’

rotary control to select.

4. Use the ‘Tune/Select’ rotary control scroll through the available options. Stop

when the sleep time you would like is displayed and press the ‘Tune/Select’ rotary

control to select. <Sleep> will be displayed.

5. Press the ‘Menu/Info’ button to return to the radio display. The sleep time minutes

that you have selected will be displayed on the top line of the display and will

countdown until the radio switches o.

Note: To cancel the sleep time, follow the steps to set the sleep time but stop

when ‘Sleep o’ is displayed.

Cancel the Sleep timer

1. Press and hold the ‘Menu/Info’ button to enter the menu options.

2. Use the ‘Tune/Select’ rotary control to scroll to ‘System’. Press the ‘Tune/Select’

rotary control to select.

3. Use the ‘Tune/Select’ rotary control to scroll to <Sleep>. Press the ‘Tune/Select’

rotary control to select. ‘

4. Use the ‘Tune/Select’ rotary control to scroll to ‘Sleep o’. Press the ‘Tune/Select’

rotary control to select. <Sleep> will be displayed.

5. Press the ‘Menu/Info’ button to return to the radio display.

Page is loading ...

Bush Bluetooth DAB Radio User manual

Brand: Bush

Model: Bluetooth DAB Radio

Category: Radios

Type: User manual

This manual is also suitable for

Download PDF

report

Bush Bluetooth DAB Radio User manual

This manual is also suitable for

Bush Bluetooth DAB Radio User manual

Related papers

Other documents