Miller RUNNING GEAR NO. 4MB 040021 Owner's manual

Type
Owner's manual

This manual is also suitable for

August 1991 FORFORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-644E
No. 4 Running Gear 040 019
No. 4A Running Gear 040 020
6
1
2
3
4
5
6
7
8
10
11
9
IMPORTANT: Be sure
that mounting hard-
ware maintains 1/2”
(12.7 mm) clearance
with all electrical parts.
Install handles onto
front panel and base.
Loosen u-bolts and install
axle/base mounting angles
on generator base. Center
axle and tighten u-bolts.
Remove paint from end of
axle and coat with grease.
Install wheels. Secure
wheels in place with retain-
ing rings.
1
2
13
14
15
13
**17
18
5
18
19
20
21
22
23
8
24
6
5
2726
26
29
28
***25
26
Install axle shaft
through
holes in cart handle as-
sembly. Install wheels
and outside flat wash-
ers. Secure wheels in
place with retaining
rings. Install front pin
support onto generator
base. Coat bottom of
pin support with grease
and install cart handle
assembly onto pin sup-
port. Secure cart handle
assembly onto pin sup-
port by installing flat
washer and retaining
rings.
**Included with Item No. 19
***Included with Item No. 24
Ref. SD-047 610-F
16
CAUTION: UNCONTROLLED TILTING OR TIPPING of unit can result in personal injury or equip-
ment damage.
Use equipment of adequate capacity to lift the unit.
If using lift forks to handle this unit, be sure the lift forks are long enough to extend out of the opposite
side of the base.
Do not place any part of the body under the unit while it is suspended.
IMPORTANT: The running gear wheels and pin support (if applicable) require periodic greasing.
OM-644 Page 2
Description
Quantity
Part
No.
Item
Model
No. 4
No. 4A
No.
1 098 733 HANDLE, cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 022 857 HANDLE, LH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 604 423 GRIP, handle 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 601 949 SCREW, cap stl hexhd .312-18 x 1.000 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 094 451 HANDLE, RH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 601 871 NUT, stl hex jam 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 213 WASHER, lock stl split .375 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 *009 542 TUBING, stl .625 OD x 12ga wall x .187 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 052 305 SCREW, SWL head .375-16 x 1.250 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 604 538 WASHER, flat stl SAE .312 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 602 211 WASHER, lock stl split .312 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 601 869 NUT, stl hex jam .312-18 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 022 825 WHEEL w/TIRE & BEARINGS, 8 in tire w/1 in brg .750 hub (consisting of) 2 2. . . . . . . . . . . . . . .
13 022 866 BEARING 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 022 619 TIRE, 400/8 4 ply 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 022 886 RIM, 8 in 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
022 622 TUBE, 400/8 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 022 861 AXLE ASSEMBLY, (consisting of) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 **145 665 RING, retaining ext 1.000 shaft (included with axle) 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 133 812 WASHER, flat stl 1.062 ID x 1.500 OD 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 022 855 AXLE, running gear (includes 2 retaining rings) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 022 609 BOLT, U .375-24 x 1.000 wide x 2.000 deep 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 602 213 WASHER, lock stl split .375 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 601 873 NUT, stl hex full fnsh .375-24 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 022 608 ANGLE, mtg bracket/base 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 080 512 SUPPORT, pivot front (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 ***121 614 RING, retaining ext .750 shaft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 602 250 WASHER, flat stl SAE .750 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 097 455 WHEEL, rbr tire 8.000 OD x 2.031 wide x .750 bore 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28 137 295 AXLE, running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29 121 614 RING, retaining ext .750 shaft 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*This item used only when mounting Blue Star Welding Generator to running gear.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
  • Page 1 1
  • Page 2 2

Miller RUNNING GEAR NO. 4MB 040021 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI