August 1991 FORFORM:
Use above FORM number when ordering extra manuals.
OWNER’S MANUAL
OM-644E
No. 4 Running Gear 040 019
No. 4A Running Gear 040 020
6
1
2
3
4
5
6
7
8
10
11
9
IMPORTANT: Be sure
that mounting hard-
ware maintains 1/2”
(12.7 mm) clearance
with all electrical parts.
Install handles onto
front panel and base.
Loosen u-bolts and install
axle/base mounting angles
on generator base. Center
axle and tighten u-bolts.
Remove paint from end of
axle and coat with grease.
Install wheels. Secure
wheels in place with retain-
ing rings.
1
2
13
14
15
13
**17
18
5
18
19
20
21
22
23
8
24
6
5
2726
26
29
28
***25
26
Install axle shaft
through
holes in cart handle as-
sembly. Install wheels
and outside flat wash-
ers. Secure wheels in
place with retaining
rings. Install front pin
support onto generator
base. Coat bottom of
pin support with grease
and install cart handle
assembly onto pin sup-
port. Secure cart handle
assembly onto pin sup-
port by installing flat
washer and retaining
rings.
**Included with Item No. 19
***Included with Item No. 24
Ref. SD-047 610-F
16
CAUTION: UNCONTROLLED TILTING OR TIPPING of unit can result in personal injury or equip-
ment damage.
• Use equipment of adequate capacity to lift the unit.
• If using lift forks to handle this unit, be sure the lift forks are long enough to extend out of the opposite
side of the base.
• Do not place any part of the body under the unit while it is suspended.
IMPORTANT: The running gear wheels and pin support (if applicable) require periodic greasing.
OM-644 Page 2
Description
Quantity
Part
No.
Item
Model
No. 4
No. 4A
No.
1 098 733 HANDLE, cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 022 857 HANDLE, LH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 604 423 GRIP, handle 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 601 949 SCREW, cap stl hexhd .312-18 x 1.000 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 094 451 HANDLE, RH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 601 871 NUT, stl hex jam 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 213 WASHER, lock stl split .375 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 *009 542 TUBING, stl .625 OD x 12ga wall x .187 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 052 305 SCREW, SWL head .375-16 x 1.250 8 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 604 538 WASHER, flat stl SAE .312 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 602 211 WASHER, lock stl split .312 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 601 869 NUT, stl hex jam .312-18 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 022 825 WHEEL w/TIRE & BEARINGS, 8 in tire w/1 in brg .750 hub (consisting of) 2 2. . . . . . . . . . . . . . .
13 022 866 BEARING 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 022 619 TIRE, 400/8 4 ply 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 022 886 RIM, 8 in 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
022 622 TUBE, 400/8 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 022 861 AXLE ASSEMBLY, (consisting of) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 **145 665 RING, retaining ext 1.000 shaft (included with axle) 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 133 812 WASHER, flat stl 1.062 ID x 1.500 OD 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 022 855 AXLE, running gear (includes 2 retaining rings) 1 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 022 609 BOLT, U .375-24 x 1.000 wide x 2.000 deep 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 602 213 WASHER, lock stl split .375 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 601 873 NUT, stl hex full fnsh .375-24 4 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 022 608 ANGLE, mtg bracket/base 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 080 512 SUPPORT, pivot front (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 ***121 614 RING, retaining ext .750 shaft 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 602 250 WASHER, flat stl SAE .750 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27 097 455 WHEEL, rbr tire 8.000 OD x 2.031 wide x .750 bore 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28 137 295 AXLE, running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29 121 614 RING, retaining ext .750 shaft 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*This item used only when mounting Blue Star Welding Generator to running gear.
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
Miller RUNNING GEAR NO. 4 040019 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KB000000 Owner's manual
-
Miller KB000000 Owner's manual
-
-
Miller KA000000 Owner's manual
-
-
-
-
-
-