Swisher 13495 Owner's manual

Owner’s

Manual

IMPORTANT

Read and follow all

Safety Precautions

and Instructions

Before Operating this

Equipment.

14100 REV. 08-065

Rear Implement

Scraper Blade

Model No.

13495

For use with

Swisher Rear Implement Mount System - P/N 6462

MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945

Rear Scraper Blade

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects

in materials and workmanship for a period of one (1) year from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

1) Commercial Use The warranty period for any product used for commercial or rental is limited to

ninety (90) days from the date of original purchase.

2) Limitations This warranty applies only to products which have been properly assembled,

adjusted, and operated in accordance with the instructions contained within this

manual. This warranty does not apply to any product of Swisher Mower Co.,

Inc., that has been subject to alteration, misuse, abuse, improper assembly or

installation, or shipping damage.

3) Exclusions Excluded from this warranty are normal wear, normal adjustments, and normal

maintenance.

In the event you have a claim under this warranty, you must return the product to an authorized service dealer.

All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or

repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this

warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase,

and the name of the authorized Swisher dealer from whom you purchased the product will be needed before

any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES

ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN

FOR ALL EXPRESSED WARRANTIES.

Some states do not allow the limitation of consequential damages or limitations on how long an implied

warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you

specific legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty as

defined by the Magnuson-Moss Act of 1975.

2

14100 REV. 08-065

Assembly Instructions

Assembly InstructionsAssembly Instructions

Assembly Instructions

P/N 13495 Scraper Blade

P/N 13495 Scraper Blade P/N 13495 Scraper Blade

P/N 13495 Scraper Blade

(Reference the Assembly Illustration on the following page)

1.

1.1.

1. Remove all components from carton and familiarize yourself with each piece.

2.

2.2.

2. Align the mount holes on the Scraper Blade mount weldment (Item 1) as shown in

the illustration. Insert 2 ea. 5/16”-18 x 1 hex bolts (Item 7) with washers (Item 16)

through the top mounting holes and fasten hand tight using 2 ea. 5/16” lock nuts (Item

8).

3.

3.3.

3. Insert 2 ea. ½”-13 hex bolts (Item 3) with washers (Item 4) through the lower

mounting holes and fasten hand tight using 2 ea. 1/2” lock nuts (Item 6).

4.

4.4.

4. Insert top mounting weldment (Item 2) into the receiver tube on the Scraper Blade

mount weldment.

5.

5.5.

5. Insert the Bell Crank bushings (Item 5) with a ½” washer (Item 4) into the curved

slots at the top of the Scraper Blade weldment. Next, insert the ½”-13 hex bolts (Item

3) with flat washers (Item 4) through the top mounting weldment (Item 2), the bell crank

bushings (Item 5) and the slots in the Scraper Blade mount weldment. Assemble

another ½” flat washer (Item 4) and hex nut (Item 6) onto the bolt and tighten securely.

The hex nut should tighten onto the Bell Crank bushing, allowing the top weldment to

rotate freely in the receiver tube.

6. Insert the ½” bent pin (Item 9) through the alignment hole in the Top mounting

weldment that will orient the blade in the desired position Secure the pin in the hole by

inserting the hair clip (Item 10) through the hole in the end of the pin.

3

Note: This Scraper Blade is designed to be used with the

Swisher ATV Rear Implement Mount System - P/N 6462.

See the Rear Implement Owners Manual for implement

mounting instructions.

14100 REV. 08-065

13495 Scraper Blade

13495 Scraper Blade 13495 Scraper Blade

13495 Scraper Blade –

––

– Assembly Illustration

Assembly IllustrationAssembly Illustration

Assembly Illustration

4

14100 REV. 08-065

1

2

3

5

4

6

9

8

7

3

4

6

8

10

11

12

14

15

13

15

13

13495 Scraper Blade – Parts List

Blade 48” - Painted7801TK110

Edge 48” - Painted7807TK111

Weldment – Frame 48” - Painted7806TK112

5/16-18 X 3/4 Carriage Bolt10216613

5/16-18 X 1 Carriage Bolt10197714

5/16 SAE Flat WasherNB2751715

Bent Pin 1/2 X 3 with Hair PinNB60619

5/16-18 NYLOC NUTNB181158

5/16-18 X 1 HCC GR5 ZPNB50127

1/2-13 Nyloc NutNB28146

Bell Crank Bushing7841Z25

1/2 USS Flat Washer ZPNB555104

1/2-13 X 1 1/2 HTC GR2 ZPNB61743

Weldment - Top, Mounting13346TK12

Weldment - Mount; Scraper Blade13347TK11

DESCRIPTIONPART NO.QTY.ITEM NO.

5

14100 REV. 08-065

6

14100 REV. 08-065

DECAL LOCATIONS

13673 DECAL

NOTES:

______________________________________________________________________

7

swisherinc.com

TELEPHONE - 1-800-222-8183

FAX - 1-660-747-8650

SWISHER MOWER & MACHINE CO. INC.

SWISHER MOWER & MACHINE CO. INC.SWISHER MOWER & MACHINE CO. INC.

SWISHER MOWER & MACHINE CO. INC.

1602 CORPORATE DRIVE

P.O. BOX 67

WARRENSBURG, MO 64093

Owner’s

Manual

Rear Scraper Blade

IMPORTANT

Read and follow all

Safety Precautions

and Instructions

Before Operating this

Equipment.

WHEN ORDERING PARTS, PLEASE HAVE THE

FOLLOWING INORMATION AVAILABLE:

* PRODUCT – ________________

* MODEL NUMBER - _______________

* PART NUMBER WITH PAINT CODE

* PART DESCRIPTION

1602 CORPORATE DRIVE PO BOX 67 WARRENSBURG, MISSOURI 64093

PH 660. 747. 8183 FAX 660. 747. 8650

swisherinc.com

MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945

Model No.1

13494

Swisher 13495 Owner's manual

Swisher 13495 Owner's manual

Related papers