Members Mark MG3208SLP Owner's manual

Brand: Members Mark

Model: MG3208SLP

Category: Barbecues & grills

Type: Owner's manual

Manual # P80109065L - Date:2008/01/14

OPERATOR'S MANUAL

Liquid Propane Gas (LPG)

Grill

Model MG3208SLP

NOTE TO ASSEMBLER / INSTALLER:

Leave this manual with the consumer.

NOTE TO CONSUMER:

Keep this manual for future reference.

RECORD YOUR SERIAL # __________________

(see silver CSA label on main body of grill)

IMPORTANT:

FREE HELP

FROM THE GRILL EXPERTS

Do not return to the store. At Grand Hall we're

the experts on this product and trained to help

you with:

Assembly questions

Grill operation

Replacement of damaged or missing parts

visit www.grandhall.com or call:

1-800-770-9769

Monday - Friday 8:00am-4:30pm CST

Failure to comply with these instructions could

result in a fire or explosion that could cause

serious bodily injury, death or property damage.

Whether this grill was assembled by you or

someone else, you must read this entire manual

before using your grill to ensure the grill is

properly assembled, installed and maintained.

Use your grill at least 3 feet away from any

wall or surface. Use your grill at least 3 feet

away from combustible objects that can melt or

catch fire such as vinyl or wood siding, fences

and overhangs or sources of ignition including

pilot lights on water heaters and live electrical

appliances.

THIS GAS APPLIANCE IS DESIGNED FOR OUT-

DOOR USE ONLY.

Never use your gas grill in a garage, porch,

shed, breezeway or any other enclosed area.

Never obstruct the flow of ventilation air

around your gas grill housing.

Never disconnect the gas regulator or any gas

fitting while your grill is lit. A lit grill can ignite

leaking gas and cause a fire or explosion which

could result in property damage, personal injury

or death.

WARNING

! !

Downloaded from www.Manualslib.com manuals search engine

Table of Contents

Primary Safety Warnings...........................1-3

Pre-Assembly Instructions..............................3

Part Diagrams and Lists........................4-10

Assembly Instructions.............................11-16

Use & Care Instructions:

• Gas Safety and Leak Tests...........17-19

• Lighting Instructions............................20-21

• Troubleshooting..........................................21

• Rotisserie Instruction...........................22-24

• Cleaning and Maintenance................25-26

• Cooking Guide...................................A1-A3

• Frequently Asked Questions............A4-A5

Warranty Terms...........................Back Cover

WARNING

! !

•

Keep gas regulator hose away from hot grill

surfaces and dripping grease. Avoid unneces-

sary twisting of hose. Visually inspect hose

prior to each use for cuts, cracks, excessive

wear or other damage. If the hose appears

damaged do not use the gas grill. Call Grand

Hall at 1-800-770-9769 for a certified replace-

ment hose.

California Proposition 65

Combustion byproducts produced when using

this product contain chemicals known to the

State of California to cause cancer, birth de-

fects, or other reproductive harm.

Brass components on the grill, such as hose

fittings, propane cylinder valves (sold sepa-

rately) and burner valve stems, contain lead

which is known to the State of California to

cause cancer, birth defects, or other reproduc-

tive harm.

Never use charcoal or lighter fluid in this gas

grill. Failure to comply with these instructions

could result in a grease fire or explosion that

could cause serious bodily injury, death or

property damage.

The Grease Draining Tray and Grease Recep-

tacle must be visually inspected before each

grill use. Remove any grease and wash Grease

Draining Tray and Grease Receptacle with a

mild soap and warm water solution. Failure to

comply with these instructions could re-

sult in a grease fire or explosion that could

cause serious bodily injury, death or prop-

erty damage.

LPG models must be used with Liquid

Propane Gas and the regulator assembly

supplied. Natural Gas models must be used

with Natural Gas only. Any attempt to convert

the grill from one fuel type to another is

hazardous and must be performed by a

qualified gas technician only, using a NG

Conversion Kit purchased from Grand Hall.

•

Keep any electrical supply cord and the fuel

supply hose away from any heated surface.

WARNING

! !

DANGER

If you smell gas:

Shut off gas to the appliance.

Extinguish any open flame.

Open lid.

If odor continues, keep away from

the appliance and immediately call

your gas supplier or your fire

department.

Do not store or use gasoline or

other flammable liquids or vapors in

the vicinity of this or any other

appliances.

An LP cylinder not connected for

use shall not be stored in the vicin-

ity of this or any other appliance.

WARNING

! !

Downloaded from www.Manualslib.com manuals search engine

Pre-Assembly Instructions For Your Safety

Grill Installation Codes

The installation must conform with local codes or, in the

absence of local codes, with either the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and

Propane Installation Code, CSA B149.1, or Propane

Storage and Handling Code, B149.2.

Spiders and small insects can spin webs and

nest in the grill Burner Tubes during transit and

warehousing which can lead to a gas flow

obstruction resulting in a fire in and around the

Burner Tubes. This type of "FLASHBACK FIRE"

can cause serious grill damage and create an

unsafe operating condition for the user.

To reduce the chance of FLASHBACK

FIRE you must clean the Burner Tubes

as follows before assembling your grill.

Also do this at least once a month in summer

and fall or whenever spiders are active in your

area, and if your grill has not been used for an

extended period of time.

Failure to comply with these instructions could

result in a fire or explosion that could cause

serious bodily injury, death or property damage.

TO CLEAN BURNER

TUBE, INSERT HOOK

HERE

WARNING

! !

METHOD 1: Bend a stiff wire or wire coat

hanger into a small hook as shown and run

the hook through the Burner Tube and inside

the Burner several times to remove debris.

METHOD 2: Use a bottle brush with a flexible

handle and run the brush through the Burner

Tube and inside the Burner several times to

remove any debris.

METHOD 3: Use an air hose to force air

through each Burner Tube. The forced air

should pass debris or obstructions through

the Burner and out the Ports.

Remove the screw from the rear of each Burner

using a Phillips Head Screwdriver.

Carefully lift each Burner up and away from the

Gas Valve Orifice.

Check and clean Burner/Venturi Tubes for

insects and insect nests. A clogged tube can

lead to a fire beneath the grill.

Refer to the figure below and perform one of

these 3 cleaning methods:

Orifice Burner Tube

Gas Valve Assembly

For safe operation ensure the Gas Valve Assembly

Orifice is inside the Burner Tube before using your

grill. See figure. If the Orifice is not inside the Burner

Tube, lighting the Burner may cause explosion

and/or fire resulting in serious bodily injury and/or

property damage.

Burner

Tools Required for Assembly:

protective work gloves

protective eyewear

While it is possible for one person to unpack this gas

grill, obtain assistance from another person when

handling the large pieces.

Use the Hardware and Part Diagrams to ensure all

items are included and free of damage.

Do not assemble or operate the grill if it appears

damaged. If there are damaged or missing parts

when you unpack the shipping box or you have

questions during the assembly process, call the:

To expedite the assembly process follow these

general guidelines:

•

Grill Information Center 1-800-770-9769

8am-4:30pm CST, Monday through Friday

•

Phillips Head Screwdriver

Burner Port

Foot

Downloaded from www.Manualslib.com manuals search engine

Hardware Pack Parts List for Models MG3208SLP

PART # PART DESCRIPTION QTYPURPOSE OF PART

P06002025A Hardware Pack 1 For use in assembly

S112G0306B Phillips Head Screw 3/16"x3/8" 4 Attaches Cart Rear Panel and Cart Side Panels

S112G0308B Phillips Head Screw 3/16"x1/2" 4

S313G0306B Flange Nut 3/16" 4

P00201001C Door Handle 2 Attaches to Doors

S112G0306B Phillips Head Screw 3/16"x3/8" 7

Attaches Partition Panel and Partition Panel Basket

to Cart

S112G0306B Phillips Head Screw 3/16"x3/8" 2

Attaches Door Bracket to Left and Right Cart Side

Panel

S112G0419B Phillips Head Screw 1/4"x1-3/16" 4 Attaches Grill Bowl to Cart

S112G0408E Phillips Head Screw 1/4"x1/2" 12

S313G0408E Flange Nut 1/4" 4

S112G0306B Phillips Head Screw 3/16"x3/8" 4

S313G0306B Flange Nut 3/16" 4

P05536001Z Hose Holder 2

S233G0408B Wing Bolt 1/4"x1/2" 1 Secures Gas Tank

S112G0304E Phillips Head Screw 3/16"x1/4" 4 Attaches Door Handles to Doors

Attaches Tank Holder to Cart Bottom Shelf

Attaches Left Side Shelf and Side Burner Frame to

Bowl Panels

Attaches Regulator Assembly to Cart Rear Panel

Already installed in the Tank Holder

Preassembled in the Door Handle

Downloaded from www.Manualslib.com manuals search engine

Hardware already installed in the Cart Bottom Shelf

Hardware Pack for Models MG3208SLP

Phillips Head Screw

1/4" x 1/2"

Qty. 12

Part # S112G0408E

Flange Nut 3/16"

Qty. 8

Part # S313G0306B

Phillips Head Screw

3/16" x 3/8"

Qty. 17

Part # S112G0306B

Phillips Head Screw

1/4" x 1-3/16"

Qty. 4

Part# S112G0419B

Flange Nut 1/4"

Qty. 4

Part # S313G0408E

Hose Holder

Qty. 2

Part # P05536001Z

Scale 1:2

Door Handle

Qty. 2

Part # P00201001C

* One Battery/AA included in the Hardware Pack.

Phillips Head Screw

3/16" x 1/4"

Qty. 4

Part # S112G0304E

Preassembled in the Door Handle

Phillips Head Screw

3/16" x 1/2"

Qty. 4

Part # S112G0308B

Wing Bolt 1/4" x 1/2"

Qty. 1

Hardware already installed on the Tank Holder

Part # S233G0408B

Downloaded from www.Manualslib.com manuals search engine

Parts Diagram for Models M3207ALP & M3207ANGParts Diagram for Models MG3208SLP

76 74

100

Downloaded from www.Manualslib.com manuals search engine

Parts List for Models MG3208SLP

KEY DESCRIPTION PART # QTY

1 Lid Assembly Y0110045

2 Temperature Gauge P00601067A

3 Lid Handle P00205069B

4 Protective Pad P05518002I

5 Cooking Rack/Secondary P01507020G

6 Cooking Grid/13" P016040144

7 Cooking Grid/6.5" P016040154

8 Burner/Main P020080244

9 Infrared Burner P020050104

10 Infrared Burner Electrode Assembly Y0320011

Savor Plates

P017080074

Savor Plates

Bracket, Front

P033280504

Savor Plates

Bracket, Rear

P033280514

14 Burner Bracket P0220342DD

15 Side Shelf, Left P011060054

16 Side Shelf Bracket, Left Front/Right Rear P01204005B

17 Side Shelf Bracket, Right Front/Left Rear P01206005B

18 Grill Bowl P0071335S4

19 Grease Draining Plate P069020094

20 Back Burner Wind Shield P06905046A

21 Back Burner Frame P02011054E

22 Back Burner P02007016D

23 Back Burner Electrode P02610005B

24 Back Burner Orifice P06527003A

25 Back Burner Extension Tube P03717050B

26 Burner Heat Shield P07523003P

27 Lid Hinge P055010204

28 Gas Collector Box with Electrode P02609030M

29 Electric Wire Set P02615120A

30 Infrared Burner Thermocouple P05305028A

31 Gas Valve/Manifold Assembly Y0060505

32 Gas Fitting P03911001A

33 Control Panel, Upper P0290919HS

34 Control Panel, Extension P0290940HS

35 Control Panel P0290930IS

36 Control Knob Seat P03415014S

37 Control Knob Spring P05504021A

38 Control Knob for Main Burner P03411503L

39 Control Knob for Back/Infrared Burner P03411513L

40 Electric Ignitor, 6-port P02502265C

41 Side Burner Lid P01127004S

42 Side Burner Frame P011040104

43 Side Burner Body P023010154

44 Side Burner Pot Support P008050104

45 Side Burner P02002012A

Downloaded from www.Manualslib.com manuals search engine

Parts List for Models MG3208SLP

KEY DESCRIPTION PART # QTY

46 Side Burner Electrode P02614007C

47 Control Knob for Side Burner P03411523L

48 Control Knob Spring P05504021A

49 Side Burner Control Knob Seat P03408053S

50 Side Burner Gas Valve Y0060506

51 Side Burner Connection Hose, Socket P03705050E

52 Side Burner Connection Hose, Plug P03705049H

53 Side Burner Extension Hose Bracket P033410014

54 Side Burner Bracket P03327029S

55 Grease Tray P02705205B

56 Grease Tray Handle P00213008O

57 Grease Tray Heat Shield P06903048B

58 Bowl Support Bracket, Left P01301007K

59 Bowl Support Bracket, Right P01302007K

60 Cart Rear Panel, Upper P069060244

61 Door Hinge Bracket, Left Upper P033020214

62 Door Hinge Bracket, Right Upper P033020224

63 Cart Side Panel, Left P07605030N

64 Cart Side Panel, Right P07603025N

65 Door Bracket P01316006K

66 Door Magnet P05523004K

67 Cart Rear Panel P07701064N

68 Cart Bottom Shelf P01003020T

69 Grease Tray Heat Shield, Upper

P06903049A 1

70 Grease Tray Heat Shield, Lower

P06903050M 1

71 Caster Seat, Left Front/Right Rear P05327035W

72 Caster Seat, Right Front/Left Rear P05327036W

73 Cart Panel Bracket-A, Left Front/Right Rear P033420014

74 Cart Panel Bracket-A, Right Front/Left Rear P033420024

75 Cart Panel Bracket-B, Left Front P033420034

76 Cart Panel Bracket-B, Left Rear P033420044

77 Cart Panel Bracket-B, Right Front P033420054

78 Cart Panel Bracket-B, Right Rear P033420064

79 Door Hinge Bracket, Left Lower P033020234

80 Door Hinge Bracket, Right Lower P033020244

81 Caster, 2.5 in., with Brake P05110006D

82 Door Handle P00201001C

83 Door, Left P04302036L

84 Door, Right P04303036L

85 Regulator with Hose P03601004A

86 Lighting Stick P05313009B

87 Hose Holder P05536001Z 2

88 Door Guide Plate P055100194 1

89 Partition Panel P07512007O 1

90 Griddle Handle P05709004E 1

91 Griddle P05705002E 1

Downloaded from www.Manualslib.com manuals search engine

Important: Use only Grand Hall certified replacement parts. The use of any part that is not a factory

authorized part can be dangerous and will also void your product warranty. Keep this Operator's Manual

for convenient referral and for part replacement.

To Order Grand Hall Certified Replacement Parts, Call 1-800-770-9769

To obtain the correct replacement parts for your gas grill, please refer to the part numbers in this parts

list. The following information is required to ensure you receive the correct parts:

1. Model and Serial Number (see CSA label on grill)

2. Part Number

3. Part Description

4. Quantity of parts needed

Parts List for Models MG3208SLP

KEY DESCRIPTION PART # QTY

Side Burner Heat shield P06907001M 1

93 Name Plate

P00414005Q 1

94 Weight

P05344003Q 2

95 Back Burner Thermocouple

P05305027A 1

96 Back Burner Thermocouple Bracket

P033430104 1

97 Tank Holder

P05358001G 1

98 Partition Panel Bracket

P03303025S 1

99 Side Burner valve Heat shield

P06915001M 1

100 Bowl Wind Shield P069060304

Grill Cover P07007018A

Rotisserie Assembly Y0250143

Hardware Pack

P06002025A

Operator's Manual P80109065L

Downloaded from www.Manualslib.com manuals search engine

Y0250143 Rotisserie Assembly Parts Diagram

Grill Information Center: If you have questions about assembly or grill operation, or

if there are damaged or missing parts when you unpack this unit from the shipping box, call us

8:00 am - 4:30 pm CST, Monday through Friday at: 1-800-770-9769

Rot. Screw#10-24x3/4"

UNC

Qty. 2

Part# S112G10124

Rot. Thumbscrew

3/8"x1/2"

Qty. 3

Part# S196G06084

Rot. Washer

Qty. 2

Part# S411G03084

Rot. Nut#10-24

Qty. 2

Part# S362G10124

Y0250143 Rotisserie Assembly Parts List

KEY

PART#

DESCRIPTION

QTY

Rot. Handle

Rot. Bushing

Rot. Thumbscrew 3/8"x1/2"

Rot. Collar

Rot. Spit

Rot. Holding Fork

Rot. Motor Bracket

Rot. Motor/AC

Rot. Screw #10-24x3/4" UNC

Rot. Washer

Rot. Nut #10-24

10.

11.

Hardware for Rotisserie

P05508004E

P05508092F

S196G06084

P05508091F

P05508146F

P05508090F

P03307010A

P07101045A

S112G10124

S411G03084

S362G10124

Downloaded from www.Manualslib.com manuals search engine

Assembly Instructions

Remove all packed components. Use the parts list to check that all necessary parts have been included.

Assemble the gas grill on a protective work surface to avoid scratching grill surfaces. Inspect your grill for damage

as you proceed. Do not assemble or operate your grill if it appears damaged.

Phillips Head Screw

3/16" x 3/8"

Qty. 4

Part # S112G0306B

Secure the Cart Rear Panel between the Cart Side Panels using

2 of 3/16"x3/8" Phillips Head Screws.

Secure the Cart Side Panel, Left/Right using 2 of 3/16"x3/8"

Phillips Head Screws.

Install Cart Rear Panel and Cart Side Panels

Unfold the Cart Side Panel, Right, Cart Side Panel, Left and Cart

Rear Panel.

Assemble Cart

Cart Rear Panel

Flange Nut 3/16"

Qty. 4

Part # S313G0306B

Phillips Head Screw

3/16" x 1/2"

Qty. 4

Part # S112G0308B

Intall the Tank holder to Cart Bottom Shelf using 4 of 3/16"x1/2"

Phillips Head Screws and 4 of 1/4" Flange Nut.

Downloaded from www.Manualslib.com manuals search engine

Door Handle

Qty. 2

Part # P00201001C

Intall the Door Handles to Doors using 4 of 3/16"x1/4" Phillips

Head Screws.

Install Door Handles, Partition Panel and Door

Install the Partition Panel Bracket between Partition Panel and

Cart Bottom Shelf using 3 of 3/16"x3/8" Phillips Head Screws.

Install the Partition Panel to Left Cart Side Panel and Cart

Rear Panel using 4 of 3/6"x3/8" Phillips Head Screws.

Phillips Head Screw

1/4" x 1-3/16"

Qty. 4

Part # S112G0419B

Install Door Bracket and Grill Bowl

Phillips Head Screw

3/16" x 3/8"

Qty. 2

Part # S112G0306B

Install the Door Bracket between the Left and Right Cart

Side Panel using 2 of 3/16" x 3/8" Phillips Head Screws.

Phillips Head Screw

3/16" x 1/4"

Qty. 4

Part # S112G0304E

Phillips Head Screw

3/16" x 3/8"

Qty. 7

Part # S112G0306B

Remove cooking components from Grill Head. With an

assistant, lift and position Grill Head on the Cart. Tighten

securely using 4 of 1/4" x 1-3/16" Phillips Head Screws.

Insert Bottom Left Door Hinge into Bottom Left Door Hinge

Bracket. Then align Top Door Hinge and insert into the hole

on Top Left Door Hinge Bracket.

Repeat both steps for Right Door.

Downloaded from www.Manualslib.com manuals search engine

Install Grease Tray

Grease Tray

Flange Nut 1/4"

Qty. 4

Part #

Install Left Side Shelf and Right Side Burner Frame

Phillips Head Screw

1/4" x 1/2"

Qty. 12

Part # S112G0408E

S313G0408E

From the front of the grill, slide the Grease Tray side tabs over the

side rails underneath the Grill Bowl.

Attach the Side Shelf to the left Bowl Panel.

Tighten securely by using Screws and Nuts provided.

Repeat both steps for Right Side Burner Frame.

Downloaded from www.Manualslib.com manuals search engine

Install Side Burner Connection Hose

Hose Holder

Sleeve

Install Regulator Assembly

Hose Holder

Qty. 2

Part # P05536001Z

Scale 1:2

Flange Nut 3/16"

Qty. 4

Part # S313G0306B

Phillips Head Screw

3/16" x 3/8"

Qty. 4

Part # S112G0306B

LPG Regulator

Cart Rear Panel

Hose

Holder

Figure A

Figure B

Figure C

SLEEVE

SOCKET

PLUG

Push back Sleeve of the Socket. See Figure A.

Insert Plug then release Sleeve. See Figure B.

Push Plug until sleeve snaps forward locking the

Plug into the Socket. See Figure C.

Push the Side Burner Hose into hose holder.

Place the LPG Regulator inside the cart through the

opening above Cart Rear Panel. Fix the hose of LPG

Regulator by Hose Holder onto Cart Rear Panel.

Tighten securely by using Screws and Nuts provided.

Downloaded from www.Manualslib.com manuals search engine

Be sure all Control Knobs are set to

"OFF" and open the Grill Lid.

Have your assistant stand behind to the

right of the grill and look toward the front

of the grill bowl. Never put your face

inside the Grill Head.

Push the Igniter Cap in and have

assistant watch for a blue spark within

each Gas Collector Box. If a spark is

present the Electrode Tips are properly

positioned.

Place the Savor Plates

above the

Burners.

Place the Cooking Grids on the ledge

above the Savor Plates

Place the Secondary Cooking Rack on

the slots on either side of the Grill

Bowl.

Savor Plates

Cooking Grids

Secondary Cooking Rack

Install Ignitor Battery

Unscrew Ignitor Cap from Control Panel.

Place supplied AA battery into the Ignitor

Slot with positive pole facing you.

Position the Cap and Spring over the AA

battery and tighten onto Control Panel.

With the assistance of another person,

perform this Electrode Check before

proceeding.

This test will ensure that the Spark Electrode Tips

are properly positioned so your grill lights easily

and properly.

Ignitor Slot

AA Battery

Ignitor Cap

Spring

Install Cooking Components

3/16"

Spark Gap

Gas Collector Box

Spark Electrode Tip

Spark Receiver

Side Burner Electrode Check

Open side burner lid. Remove plastic

shipping band from burner and pot

support.

Push and turn side burner Control Knob

to HIGH. Look for spark between tip of

electrode and burner.

If you don't see a spark from side burner elec-

trode, adjust gap between electrode and

burner surface to 3/16 in.

Final Grill Assembly Step

When you have finished assembling your

grill be sure that all screws are tightened

for safe operation of your grill.

Failure to read and follow the Use and Care

Instructions could result in a fire or explosion

that could cause serious bodily injury, death or

property damage.

WARNING

Downloaded from www.Manualslib.com manuals search engine

Optional Wind Shield for More Effective Cooking

When cooking with only the main burners you can generate more heat for your cooking if you

place the wind shield on your cooking grid. If the searing burner is in operation there is no need

for the wind shield.

Open lid and remove the secondary cooking rack.

Before igniting burners, tilt the cooking grid up at the middle point of the grill. See Fig. 1.

Place the base of the wind shield in-between the cooking grids and then lower

the cooking grid to its original position. See Fig. 2.

Replace the secondary cooking rack.

The Right Rack

Fig. 1.

Bowl Wind Shield

The Right Rack

Fig. 2.

Bowl Wind Shield

Do NOT Touch after cooking.

WARNING

Fig. 1.

Downloaded from www.Manualslib.com manuals search engine

USE AND CARE INSTRUCTIONS

CORRECT LP GAS TANK USE

LP Gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas (LP Gas) tank,

not included with grill. Never connect your gas grill to

an LP Gas tank that exceeds this capacity. A tank of

approximately 12 inches in diameter by 18-1/2 inches

high is the maximum size LP Gas tank to use. You

must use an "OPD" gas tank which offers a listed

Overfill Prevention Device. This safety feature

prevents tank from being overfilled which can cause

malfunction of LP Gas tank, regulator and/or grill.

Never connect an unregulated LP gas tank to your

gas grill. The gas regulator assembly supplied with

your gas grill is adjusted to have an outlet pressure

of 11" water column (W.C.) for connection to an LP

gas tank. Only use the regulator and hose assembly

supplied with your gas grill. Replacement regulators

and hose assemblies must be those specified by

the Manufacturer.

Have your LP Gas dealer check the release valve

after every filling to ensure it remains free of defects.

Always keep LP Gas tank in upright position.

Do not subject the LP Gas tank to excessive heat.

Never store an LP Gas tank indoors. If you store

your gas grill in the garage always disconnect the

LP Gas tank first and store it safely outside.

LP Gas tanks must be stored outdoors in a well-

ventilated area and out of the reach of children.

Disconnected LP Gas tanks must not be stored in a

building, garage or any other enclosed area.

The regulator and hose assembly can be seen after

opening the doors (if applicable) and must be

inspected before each use of the grill. If there is

excessive abrasion or wear or if the hose is cut, it

must be replaced prior to using the grill again.

Never light your gas grill with the lid closed or

before checking to ensure the burner tubes are fully

seated over the gas valve orifices.

Never allow children to operate your grill. Do not

allow children or pets to play near your grill.

Keep fire extinguisher readily accessible. In the

event of a oil/grease fire, do not attempt to

extinguish with water. Use type B extinguisher

or smother with dirt, sand or baking soda.

In the event of rain, cover the grill and turn off

the burner and gas supply.

Use your grill on a level, stable surface in an

area clear of combustible materials.

Do not leave grill unattended when in use.

Do not move the appliance when in use.

Allow the grill to cool before moving or storing.

Do not use your grill as a heater.

This grill is not intended to be installed in

or on recreational vehicles and/or boats.

Never use charcoal in this gas grill.

The LP Gas tank must be constructed and marked

in accordance with the Specifications for LP-Gas

Cylinders of the U.S. Department of Transportation

(D.O.T.) or the National Standard of Canada, CAN/

CSA-B339, Cylinders, Spheres and Tubes for Trans-

portation of Dangerous Goods; and Commission,

as applicable.

The LP Gas tank must have a shutoff valve,

terminating in an LP Gas supply tank valve outlet,

that is compatible with a Type 1 tank connection

device. The LP Gas tank must also have a safety

relief device that has a direct connection with the

vapor space of the tank.

The tank supply system must be arranged for

vapor withdrawal.

The LP Gas tank used must have a collar

to protect the tank valve.

•

WARNING

Do not store a spare LP-Gas tank under or near

this appliance.

Never fill the tank beyond 80 percent full; and

If the information in "(a)" and "(b)" is not followed

exactly, a fire causing death or serious injury may

occur.

Use your grill at least 3 feet away from any

wall or surface. Use your grill at least 3 feet

away from combustible objects that can melt

or catch fire such as vinyl or wood siding, fences

and overhangs or sources of ignition including pilot

lights on water heaters and live electrical appliances.

Outdoor cooking gas appliance shall not be used

under overhead combustible construction.

Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area.

Never obstruct the flow of ventilation air around your

gas grill housing.

In windy conditions, always position the front of grill to

face oncoming wind to reduce smoke and heat blowing in

your face and prevent potential hazards to self and grill.

WARNING

•

3ft.

WIND

DIRECTION

•

Use of alcohol, prescription or non-prescription

drugs can impair your ability to properly assemble

and safely operate your grill.

Downloaded from www.Manualslib.com manuals search engine

USE AND CARE INSTRUCTIONS

NOTE about LP Gas Tank Exchange Programs

Many retailers that sell grills offer you the option of

replacing your empty LP Gas tank through an ex-

change service. Use only those reputable exchange

companies that inspect, precision fill, test and certify

their tanks. Exchange your tank only for an OPD safety

feature-equipped tank as described in the LP Gas tank

section of this manual.

How to Leak Test your LP Gas Tank

If growing bubbles appear do not use or move

the LP Gas tank. Contact an LP Gas Supplier

or your fire department!

WARNING

Use a clean paintbrush and a 50/50 mild soap and

water solution.

Brush soapy solution onto LP Gas tank in the

areas indicated by the arrows. See diagram.

If growing bubbles appear do not use or move the

LP Gas tank. Call an LP Gas Supplier or your Fire

Department.

All leak tests must be repeated each time your LP

Gas tank is exchanged or refilled.

When checking for gas leaks do not smoke.

Do not use an open flame to check for gas leaks.

Your grill must be leak tested outdoors in a well-

ventilated area, away from ignition sources such as

gas fired or electrical appliances. During the leak test,

keep your grill away from open flames or sparks.

Do not use household cleaning agents. Damage to

gas assembly components can result.

For your safety:

Leak test new and exchanged LP Gas tanks BEFORE

connecting one to your grill.

Always keep new and exchanged LP Gas tanks in an

upright position during use, transit or storage.

LP Gas Model only:

Secure a 20lb LP Gas Tank to Gas Grill or

Range

One Nut is fixed to

Tank Holder. An

additional Nut and

Wing Bolt is secured

AFTER inserting tank

into tank hole.

Wing Bolt 1/4"x1/2"

Qty. 1

Part # S233G0408B

Additional Nut

Turn your LP Gas Tank Valve clockwise to the

closed or OFF positon.

Unscrew the Wing Bolt from right bracket of tank

holder.

Place LP Gas tank into tank holder on the Tank

Tray.

Install the tank so the Tank Valve faces the rear

right corner of cabinet.

Align an additional nut and screw the Wing Bolt

into right bracket of tank holder to secure the

gas tank.

Downloaded from www.Manualslib.com manuals search engine

USE AND CARE INSTRUCTIONS

Check all connections for LP Gas Leaks

Never test for leaks with a flame. Prior to first use,

at the beginning of each season, or every time

your LP Gas tank is changed, you must check for

gas leaks. Follow these three steps:

Make a soap solution by mixing one part liquid

detergent and one part water.

Turn the grill Control Knobs to the full OFF

position, then turn the gas ON at source.

Apply the soap solution to all gas connections

indicated by the arrows. See diagram. If

bubbles appear in the soap solution the

connections are not properly sealed. Check

each fitting and tighten or repair as necessary.

Gas Valve / Manifold Assembly

Regulator with Hose (LPG)

LP Gas Tank

If you have a gas leak that cannot be repaired by

tightening, turn off the gas at the source, disconnect

fuel line from your grill and call 1-800-770-9769

or your gas supplier for repair assistance.

Never disconnect the gas regulator or any gas

fitting while your grill is lit. A lit grill can ignite

leaking gas and cause a fire or explosion which

could result in property damage, personal injury

or death.

WARNING

! !

LP Gas Model only:

Connect Regulator with Hose to your LPG Tank

Turn all Burner Valves to the OFF position.

Inspect the valve connection port and regulator

assembly for damage or debris. Remove any

debris. Never use damaged or plugged

equipment.

Connect the regulator assembly to the tank valve

and HAND TIGHTEN nut clockwise to a full stop.

DO NOT use a wrench to tighten because it could

damage the Quick Coupling Nut and result in a

hazardous condition.

Open the tank valve 1/4 to 1/2 (counterclockwise)

and use a soapy water solution to check all

connections for leaks before attempting to light

your grill. See "Checking for LP Gas Leaks". If

a leak is found, turn the tank valve off and do not

use your grill until the leak is repaired.

Type 1 connection per

ANSI Z21.58- 2007

Quick

Coupling Nut

CAUTION: When the appliance is not in use the gas

must be turned off at the tank.

Before using this gas appliance read all

instructions and perform all gas leak-check

procedures even if the product was

pre-assembled by the retailer or manufacturer.

WARNING

! !

Disconnecting A Liquid Propane Gas (LPG)

Tank From Your Grill

Make sure the Burner Valves and LP Gas tank valve

are off. (Turn clockwise to close.)

Detach the hose and regulator assembly from the

LP Gas tank valve by turning the Quick Coupling

Nut counterclockwise.

Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust

cap on the cylinder valve outlet that is provided with

the cylinder valve. Other types of caps or plugs may

result in leakage of propane.

Downloaded from www.Manualslib.com manuals search engine

Grill Lighting Instructions

Set Control Knobs to OFF and open the LP Gas

SLOWLY 1/4 of a turn.

Push and turn the Main Burner Control Knob to

ON/ . Always light the LEFT Main Burner first.

Press the electric ignitor 3 to 4 seconds to light the

burner.

If ignition does not occur in 5 seconds, turn gas off

at source and turn Control Knobs OFF. Wait at least

5 minutes for gas to clear, then retry. If your grill still

fails to light turn the burner Control Knob(s) and gas

source OFF and conduct a leak test of ALL gas

connections and gas sources as explained in the

Use and Care section of this manual. If no leaks are

detected, wait 5 minutes for any gas to clear and

repeat the lighting procedure.

After one Burner is lit, turn the tank valve SLOWLY

one more 1/4 of a turn for 1/2 of one complete turn.

Repeat steps to light each burner individually. Turn

other burners to ON/ to light as you move towards

the fuel source.

IMPORTANT: Do not use the Back Burner and

Main Burners at the same time. Backburner is

for Rotisserie Cooking only.

Follow steps 1 through 6 of the Grill Lighting

Instructions.

Then, push and turn the Infrared Burner Control Knob

to ON/ and press the electric ignitor 3 to 4 seconds

to light the burner. Hold the knob in 10 seconds be-

fore releasing. If ignition does not occur follow step 7

before retrying.

After the Infrared Burners is lit it will reach cooking

temperature quickly. The orange/red glow will even

out within minutes.

ON/

Back Burner Lighting Instructions

Follow steps 1 through 6 of the Grill Lighting

Instructions.

Then, push and turn the Back Burner Control Knob

to ON/ and press the electric ignitor 3 to 4

seconds to light the Burner. Hold the knob in 10

seconds before releasing. If ignition does not occur

follow step 7 before retrying.

After the Back Burner is lit it will reach cooking

temperature quickly. The orange/red glow will

even out within minutes.

Infrared Burner Lighting Instructions

Burner Control Knobs on Control Panel

OFF

Grill

Main Burner

Back

Burner

Infrared

Burner

Follow steps 1 through 5 of the Grill Lighting

Instructions.

Set Control Knob to OFF and open the LP Gas tank

valve SLOWLY 1/4 of a turn.

Push and turn the Control Knob to ON/ . The built

spark ignitor will light the Burner automatically.

You may have to pusk and turn the Control Knob up to

3 to 4 times to light.

If ignition does not occur, turn the burner Control Knob

and gas source OFF and conduct a leak test of ALL

gas connections and fuel sources. If no leaks are

detected, wait 5 minutes for any gas to clear and re-

peat the lighting procedure.

Side Burner Lighting Instructions

USE AND CARE INSTRUCTIONS

tank valve

Open LP

gas tank

Failure to replace a faulty hose, secure gas supply

connections or to open the Lid before proceeding

to the Lighting Procedures could result in a fire

or explosion that could cause serious bodily injury,

death, or property damage.

WARNING

OFF

ON/

OFF

LOW

OFF

Before each use, check all hoses for cracks, nicks, cuts,

burns or abrasions. If a hose is damaged in any way, do

not use your grill before replacing the hose with an

authorized part from the Parts List. Also make sure all

gas supply connections are securely tightened.

Familiarize yourself with the safety and Use and Care

instructions in this manual. Do not smoke while lighting

grill or checking gas supply connections.

Be sure the LP Gas tank is filled.

Open the Grill Lid during lighting.

Check that the end of each Burner Tube is properly

located over each Valve Orifice (see page 25).

Open Side Burner Lid.

Downloaded from www.Manualslib.com manuals search engine

Page is loading ...

Members Mark MG3208SLP Owner's manual

Brand: Members Mark

Model: MG3208SLP

Category: Barbecues & grills

Type: Owner's manual

Download PDF

report

in other languages

español: Members Mark MG3208SLP El manual del propietario

Members Mark MG3208SLP Owner's manual

Members Mark MG3208SLP Owner's manual

in other languages

Related papers

Other documents