Eiki LC-X800 User manual

MULTIMEDIA PROJECTOR

MODEL LC-X800

OWNER’S MANUAL

✽ Projection lens is optional.

Printed in Japan

1AA6P3P1533--

(KE8A)

EN

CORRECTION NOTICE

The following is the correction to the owner's manual and the quick reference guide.

Please refer to Voltage and Power Consumption on page 77 of the owner’s manual and

on page 20 of the quick reference guide.

AC 100–120 V (9.9 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)

AC 200–240 V (4.8 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)

FR

AVIS DE CORRECTION

Les corrections suivantes sont apportées au mode d'emploi et au guide de référence ra-

pide. Reportez-vous à la section Tension et consommation en page 77 du mode d'emploi

et à la page 20 du guide de référence rapide.

100 - 120 V CA (9,9 A max. ampères), 50/60 Hz (Etats-Unis et Canada)

200 - 240 V CA (4,8 A max. ampères), 50/60 Hz (Europe continentale et Royaume-Uni)

ES

NOTA DE CORRECCIÓN

A continuación se incluye una corrección al manual del usuario y la guía de referencia

rápida. Consulte el apartado Voltaje y consumo eléctrico en la página 77 del manual del

usuario y en la página 20 de la guía de referencia rápida.

CA 100 - 120 V (amperaje máx. de 9,9 A), 50/60Hz (en EE.UU. y Canadá)

CA 200 - 240 V (amperaje máx. de 4,8 A), 50/60Hz (en Europa continental y Reino Unido)

DE

KORREKTURHINWEIS

Es folgt die Korrektur der Bedienungsanleitung und der Kurzanleitung.

Weiteres ﬁnden Sie unter Spannung und Leistungsaufnahme auf der Seite 77 der

Bedienungsanleitung und auf Seite 20 der Kurzanleitung.

Netzspannung 100 - 120 V (max. 9,9 A), 50/60 Hz (USA und Kanada)

Netzspannung 200 - 240 V (max. 4,8 A), 50/60 Hz (Kontinentaleuropa und Großbritannien)

IT

COMUNICATO DI RETTIFICA

Quanto segue è la correzione al manuale utente e alla guida di riferimento rapido.

Consultare Voltaggio e potenza assorbita a pagina 77 del manuale utente e a pagina 20

della guida di riferimento rapido.

100 - 120 Vc.a. (9,9 A amperaggio max.), 50/60 Hz (U.S.A. e Canada)

200 - 240 Vc.a. (4,8 A amperaggio max.), 50/60 Hz (Europa continentale e Regno Unito)

PT

AVISO DE CORREÇÃO

Segue-se uma correcção ao manual do utilizador e ao guia de referência rápida.

Consulte a secção Voltagem e Consumo de Energia na página 77 do manual do utilizador

e na página 20 do guia de referência rápida.

CA 100 - 120 V (9,9 A Máx. Amperagem), 50/60 Hz (EUA e Canadá)

CA 200 - 240V (4,8 A Máx. Amperagem), 50/60 Hz (Europa Continental e Reino Unido)

2

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This

projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD)

technology.

◆ Functionally Rich

◆ Simple Computer System Setting

The projector has the Multi-scan system to

conform to almost all computer output signals

quickly (p.34). Supported resolution up to WUXGA.

◆

Multilanguage Menu Display

Operation menu is available in 12 languages;

English, German, French, Italian, Spanish,

Portuguese, Dutch, Swedish, Russian, Chinese,

Korean, and Japanese (p.48).

◆

Useful Functions for Presentation

Digital zoom function allows you to focus on the

crucial information during a presentation (pp.29,

40).

◆ Power Management

The Power management function reduces power

consumption and maintains lamp life (p.52).

◆ Logo Function

The Logo function allows you to customize the

screen logo (pp.49–50). You can capture an image

for the screen logo and use it for the starting-up

display or between presentations.

◆ Security Function

The Security function helps you to ensure security

of the projector. With the Key lock function, you can

lock the operation on the side control or remote

control (p.53). PIN code lock function prevents

unauthorized use of the projector (pp.53–54).

This projector has many useful functions such

as lens shifting, ceiling and rear projection,

perpendicular omnidirectional projection, variety of

lens options, etc.

✔Note:

•The On-Screen Menu and figures in this manual may differ slightly from the product.

•The contents of this manual are subject to change without notice.

Features and Design

◆ Motor-driven Lens Shift

◆ Shutter Function

The projector is equipped with the shutter that

provides complete blackness for a while the

projected image is not needed with keeping the

projector on. The Shutter management function

allows you to set the timer. It prevents leaving the

projector on with the shutter closed for a long time

(p.55).

◆ Multi Versatile Platform

This projector applies various input/output

terminals and 2 terminal slots for expansion to tune

to diversity of signals from computers and video

equipment (p.19). For optional interface boards,

contact sales dealer where you purchased the

projector.

◆ Automatic Filter Replacement Function

The projector monitors the condition of the filter

and replaces a filter automatically when it detects

the clogging.

◆ Helpful Maintenance Functions

Lamp and filter maintenance functions provide for

better and proper maintenance of the projector.

◆ Network board (Optional)

Network board is an optional product to control

and set up the projector via the network cables

with the web browser on your computer. It can

be controlled and set up the projector remotely.

Contact the sales dealer where you purchased this

projector for optional parts.

Projection lens can be moved up, down, right and

left with the motor-driven lens shift function. This

function makes it easy to provide projected image

where you want. Zoom and focus can also be

adjusted with a motor-driven operation (p.27).

* Zoom and focus functions may not operate

depending on the optional lens.

◆ New Optical Technology

This projector is equipped with a new optical

engine. The new optical engine controls the

amount of yellow light in the image, producing

higher brightness with improved color accuracy

and clarity (p.46).

3

Trademarks

Each name of corporations or products in this book is either a registered trademark or a trademark of its respective

corporation.

Table of Contents

Features and Design................ 2

Table of Contents .................. 3

To The Owner ..................... 4

Safety Instructions ................. 5

Air Circulation 6

Installing the Projector in Proper Directions 7

Moving the Projector 8

Compliance ....................... 9

Part Names and Functions.......... 10

Front 10

Back 10

Terminals and Connectors 11

Side Control and Indicators 12

Side Control 12

Indicators 13

Remote Control 14

Remote Control Battery Installation 15

Remote Control Receivers and Operating Range 15

Wired Remote Control 15

Remote Control Code 16

Installation ...................... 17

Lens Installation 17

Installing the Strap for safety 17

Positioning Projector 18

Lens Shift Adjustment 18

Picture Level and Pitch Adjustment 18

Terminals of Projector 19

Connecting to Computer 20

Connecting to Video Equipment 21

Connecting the AC Power Cord 22

Basic Operation .................. 23

Turning On the Projector 23

Turning Off the Projector 24

How to Operate the On-Screen Menu 25

Menu Bar 26

Operating with Projector Control 27

Operating with Remote Control 29

Input Selection ................... 31

Input 31

Computer Input Source Selection 32

Video Input Source Selection 33

Computer Input .................. 34

Computer System Selection 34

Auto PC Adjustment 35

Manual PC Adjustment 36

Image Level Selection 38

Screen Size Adjustment 39

Video Input ...................... 41

Video System Selection 41

Image Level Selection 42

Screen Size Adjustment 43

Picture Image .................... 45

Image Adjustment 45

Setting .......................... 48

Setting 48

Maintenance and Care ............. 57

Filter Instructions 57

Replacing the Filter Cartridge 58

Resetting the Filter Counter 59

Resetting the Scroll Counter 59

Lamp Management 60

Lamp Replacement 61

Resetting the Lamp Counter 62

Cleaning the Projection Lens 64

Cleaning the Projector Cabinet 64

Warning Indicators 65

Appendix ........................ 66

Troubleshooting 66

Menu Tree 69

Indicators and Projector Condition 72

Compatible Computer Specifications 75

Technical Specifications 77

Optional Parts 78

Configurations of Terminals 79

PIN Code Number Memo 80

Dimensions 81

Serial Control Interface 82

4

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE EXCEPT LAMP REPLACEMENT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS

VOLTAGE CONSTITUTING A RISK OF ELECTRIC

SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE OWNER’S MANUAL WITH

THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before installing and operating the projector, read this

manual thoroughly.

The projector provides many convenient features and

functions. Operating the projector properly enables you to

manage those features and maintains it in good condition for

many years to come.

Improper operation may result in not only shortening the

product life, but also malfunctions, fire hazard, or other

accidents.

If your projector seems to operate improperly, read this

manual again, check operations and cable connections and

try the solutions in the “Troubleshooting” section in the

back of this manual. If the problem still persists, contact the

dealer where you purchased the projector or the service

center.

CAUTION

Not for use in a computer room as defined in the

Standard for the Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

CAUTION ON HANGING FROM THE CEILING

When hanging the projector from the

ceiling, clean the air intake vents and

top of the projector periodically with a

vacuum cleaner. If you leave the projector

unclean for a long time, the cooling fans

can be clogged with dust, and it may

cause a breakdown or a disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR

SMOKY CONDITIONS SUCH AS IN A KITCHEN TO

PREVENT A BREAKDOWN OR A DISASTER. IF THE

PROJECTOR COMES IN CONTACT WITH OIL OR

CHEMICALS, IT MAY BECOME DETERIORATED.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER

USE.

To The Owner

Safety Precaution

WARNING: l THIS APPARATUS MUST BE EARTHED.

l TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

– This projector produces intense light from the projection lens.

Do not stare directly into the lens, otherwise eye damage could

result. Be especially careful that children do not stare directly

into the beam.

– Install the projector in a proper position. Otherwise it may

result in a fire hazard.

– Allowing the proper amount of space on the top, sides, and

rear of the projector cabinet is critical for proper air circulation

and cooling of the unit. The diagrams shown here indicates the

minimum space required. If the projector is to be built into a

compartment or similarly enclosed, these minimum distances

must be maintained.

– Do not cover the ventilation slots on the projector. Heat build-

up can reduce the service life of your projector, and can also be

dangerous.

– If the projector is unused for an extended time, unplug the

projector from the power outlet.

– Do not project the same image for a long time, since the

afterimage may remain on the LCD panels by the characteristic

of panel.

3.3' (1m)

SIDE and TOP REAR

The symbol mark and recycling systems described below

apply to EU countries and do not apply to countries in other

areas of the world.

Your product is designed and manufactured with high qual-

ity materials and components which can be recycled and/or

reused.

The symbol mark means that electrical and electronic

equipment, batteries and accumulators, at their end-of-life,

should be disposed of separately from your household

waste.

Note:

If a chemical symbol is printed beneath the symbol mark,

this chemical symbol means that the battery or accumula-

tor contains a heavy metal at a certain concentration. This

will be indicated as follows: Hg: mercury, Cd: cadmium, Pb:

lead.

In the European Union there are separate

collection systems for used electrical and

electronic equipment, batteries and accumu-

lators.

Please, dispose of them correctly at your

local community waste collection/recycling

centre.

Please, help us to conserve the environment we live in!

5

All the safety and operating instructions should be read

before the product is operated.

Read all of the instructions given here and retain them for

later use. Unplug this projector from AC power supply

before cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning

storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet. This will

prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do n ot u s e att ach men ts n o t rec omm end e d by the

manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or

table. The projector may fall, causing serious injury to a child

or adult, and serious damage to the projector. Use only with

a cart or stand recommended by the manufacturer, or sold

with the projector. Wall or shelf mounting should follow the

manufacturer's instructions, and should use a mounting kit

approved by the manufacturers.

An appliance and cart combination

should be moved with care. Quick

stops, excessive force, and uneven

surfaces may cause the appliance and

cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are

provided for ventilation, to ensure reliable operation of the

equipment and to protect it from overheating.

The openings should never be covered with cloth or other

materials, and the bottom opening should not be blocked

by placing the projector on a bed, sofa, rug, or other similar

surface. This projector should never be placed near or over a

radiator or heat register.

This projector should not be placed in a built-in installation

such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through

cabinet slots as they may touch dangerous voltage points

or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air-

conditioning equipment.

This projector should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supplied, consult your authorized

dealer or local power company.

Do not overload wall outlets and extension cords as this

can result in fire or electric shock. Do not allow anything to

rest on the power cord. Do not locate this projector where

the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening

or removing covers may expose you to dangerous voltage

or other hazards. Refer all servicing to qualified service

personnel.

Unplug this projector from wall outlet and refer servicing to

qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the projector to normal

operation.

e. If the projector has been dropped or the cabinet has

been damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer that have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or injury to persons.

Upon completion of any service or repairs to this projector,

ask the service technician to perform routine safety

checks to determine that the projector is in safe operating

condition.

Safety Instructions

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY

AND MUST BE RECYCLED OR DISPOSED OF ACCORDING

TO LOCAL, STATE OR FEDERAL LAWS.

6

Openings in the cabinet are provided for ventilation. To

ensure reliable operation of the product and to protect

it from overheating, these openings must not be

blocked or covered.

CAUTION

Hot air is exhausted from the exhaust vent. When

using or installing the projector, the following

precautions should be taken.

– Do not put any flammable object or spray can near

the projector, hot air is exhausted from the air vents.

– Keep the exhaust vent at least 3’ (1 m) away from

any objects.

– Do not touch peripheral parts of the exhaust vent,

especially screws and metallic parts. These areas will

become hot while the projector is being used.

– Do not put anything on the cabinet. Objects put on

the cabinet will not only get damaged but also may

cause fire hazard by heat.

– Do not cover vents with papers or other materials.

– Make sure that there are no objects under the

projector. An object under the projector may prevent

the projector from taking cooling air through bottom

vent.

Cooling fans are provided to cool down the projector.

The fans’ running speed is changed according to the

temperature inside the projector.

Air Circulation

Safety Instructions Safety Instructions

EXHAUST VENT

AIR INTAKE VENT

The projector uses a lamp which generates

significant heat. The cooling fans and air vents are

provided to dissipate the heat by drawing air into the

housing and the filter is located in the intake vents to

prevent dust from getting inside of the projector.

In order to care for the projector appropriately,

regular cleaning is required. Remove any dirt or dust

that has accumulated on the projector.

If the projector reaches a time set in the timer

setting, a Filter replacement icon (Fig. 1) appears on

the screen and WARNING FILTER indicator on the

top panel lights up (see below), indicating that the

filter replacement is necessary.

If the projector detects that the filter is clogged and

no scroll is left in the filter cartridge, a Filter cartridge

replacement icon (Fig. 2) appears on the screen and

WARNING FILTER indicator on the top panel lights

up (see below). Stop using the projector immediately

and replace the filter cartridge.

Blocking the air vents and leaving the projector

uncleaned for a long time may not only damage the

projector and may require costly repairs but may also

cause accidents or fire.

For maintenance of the filter, refer to “Filter counter”

on page 56 and “Maintenance and Care” on pages

57–59.

Damages to the projector caused by using an

uncleaned filter or improper maintenance will

void the warranty on the projector.

IMPORTANT!

Filter Maintenance!!

Top Panel

WARNING FILTER

indicator

Fig.1 Filter replacement icon

Fig.2 Filter cartridge replacement

icon

7

Safety Instructions

Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in

severe accident or fire hazard.

This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the

horizontal plane.

Installing the Projector in Proper Directions

Avoid positioning the projector as described below when installing.

Positioning Precautions

Do not roll the projector more

than 10 degrees from side to

side.

For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted

properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty

on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit

or installation of the ceiling mount kit in an improper location.

CAUTION ON CEILING MOUNTING

10˚

Do not put the projector

on either side to project an

image.

10˚10˚

10˚

In upward projection, do

not tilt the projector over 10

degrees right and left.

In downward projection, do

not tilt the projector over 10

degrees right and left.

✔Note:

•To inverse or reverse the image, set the ceiling function to “On.” (pp. 40, 44)

•The projector can not be operated at an altitude above 3,000 meters.

8

Moving the Projector

Safety Instructions

Retract the adjustable feet to prevent damage

to lens and cabinet. For safety, holding the

projector on both sides by 2 or more people is

recommended to move the projector because

the projector is heavy. When moving the

projector by one person from necessity, hold

the handle carefully. Do not hold the lens

mount cover. Moving it improperly may result

in damage of cabinet or person's injury.

CAUTION IN CARRYING OR

TRANSPORTING THE PROJECTOR

– Do not drop or bump the projector, otherwise

damages or malfunctions may result.

– When carr ying the projector, use a suitable

carrying case.

– Do not transport the projector by courier or any

other transport service in an unsuitable transport

case. This may cause damage to the projector. For

information about transporting the projector by

courier or any other transport service, consult your

dealer.

– Do not put the projector in a case before it is

cooled enough.

– Do not transport the projector with a replacement

lens installed.

9

AC Power Cord for the United Kingdom:

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin

face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the

same rating, marked thus

A S A

. If the fuse cover is detachable, never use the plug with the cover omitted. If a

replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e.

red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted.

WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET

OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············· Earth

Blue ································· Neutral

Brown ······························ Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol

or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured

red.

WARNING: THIS APPARATUS MUST BE EARTHED.

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure

that the plug will fit into the power outlet. Do not try to defeat this safety feature.

Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC Power Cord Requirement

Compliance

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise specified in the

instructions. If such changes or modifications should be made, you could be required to stop operation

of the equipment.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Canadian Radio Interference Regulations

This Class A digital apparatus meets all requirements of the Canadian ICES-003.

GROUND

10

ue r t

Front

o

q

w

y i

Back

qLens Mount Cover

wProjection Lens (Option)

e Indicators

rInfrared Remote Receiver (Front)

!2

CAUTION

Hot air is exhausted from the exhaust

vent. Do not put heat-sensitive objects

near this side.

!0 Infrared Remote Receiver (Rear)

!1Exhaust Vent

t Adjustable Feet

y

Terminals and Connectors

u Handle

i Side Control

o Lamp Cover

!1 !3

Part Names and Functions

!0

!4

!5

t

!1

✽Kensington Security Slot

This slot is for a Kensington lock used

to deter theft of the projector.

* Kensington is a registered trademark of ACCO Brands

Corporation.

✽

!2Main On/Off Switch

!3 Power Cord Connector

!4 Air Intake Vent

!5 Air Filter Cover

11

Terminals and Connectors

rR/C JACK

When using the wired remote control, connect the

wired remote control to this jack with a remote

control cable (supplied).

eUSB CONNECTOR (Series B)

USB connector is to used to service the projector.

iS-VIDEO INPUT JACK

Connect the S-VIDEO output signal from video

equipment to this jack (p.21).

q

SERIAL PORT IN TERMINAL

If you control the projector by computer, you must

connect a cable (not supplied) from your computer

to this terminal.

w

SERIAL PORT OUT TERMINAL

This terminal outputs signal from SERIAL PORT IN.

More than two projectors can be controlled with

one computer by connecting SERIAL PORT IN of

another projector to this terminal.

u5 BNC INPUT JACKS

Connect the component or composite video

output signal from video equipment to VIDEO/Y,

Pb/Cb, and Pr/Cr jacks or connect the computer

output signal (5 BNC Type [Green, Blue, Red,

Horiz. Sync, and Vert. Sync.]) to G, B, R, H/V, and V

jacks (pp.20–21).

[ RESET button

A built-in micro processor which controls this unit may

occasionally malfunction and need to be reset. This can be done

by pressing the RESET button with a pen, which will shut down

and restart the unit. Do not use the RESET function excessively.

q w

e

r

✽

t y

i

u

t

DVI INPUT TERMINAL

Connect computer output (Digital/DVI-D type) to

this terminal (p.20).

HD (HDCP Compatible) signal can be also

connected (p.21).

y

D-sub 15-PIN INPUT TERMINAL

Connect computer output (Analog D-sub 15-pin

type) to this terminal (pp.20–21).

Part Names and Functions

12

iFOCUS button

Adjust the focus (p.27).

wZOOM button

Zoom in and out the images (p.27).

qON/STAND-BY button

Turn the projector on or off (pp.23,24).

o INPUT button

Select an input source Input 1, Input 2, Input 3 or

Input 4 (pp.31-33).

yAUTO PC ADJ. button

Automatically adjust the computer image to its

optimum setting (pp.27, 35).

rPOINT buttons

- Select an item or adjust the value in the On-

Screen MENU (p.25).

- Pan the image in DIGITAL ZOOM + mode (p.40).

Side Control and Indicators

uLENS SHIFT button

Select the LENS SHIFT function (p.27).

!0SELECT button

Used to execute the selected item (p.25). It is

also used to expand or compress the image in

DIGITAL ZOOM mode (p.40).

eMENU button

Open or close the On-Screen MENU (pp.25, 26).

Part Names and Functions

SIDE CONTROLS

INDICATORS

Side Control

q

w

e

r

t

y

i

u

!1

!0

o

t

SHUTTER button

Close and open up the built-in shutter (p.27).

!1 INFORMATION button

Display the input source information (p.28).

13

Indicators

q

w

e

r

t

y

u

eWARNING TEMP. indicator

This indicator flashes red when internal projector

temperature is too high (pp.65, 72-74).

u LAMP 1 REPLACE indicator

Turn orange when the life of the projection lamp1

draws to an end (p.61, 73).

qLAMP Indicator

This indicator is dim when the projector is turned

on. And bright when the projector is in stand-by

mode (pp.72-74).

wREADY indicator

This indicator lights green when the projector

is ready to be turned on. And it flashes green in

Power Management mode (pp.52, 72-74).

Part Names and Functions

rWARNING FILTER indicator

– Blink slow when the filter is being scrolled (pp.

57, 72).

– Blink fast when the filter scroll is not working

properly or the filter cartridge is not installed

(pp.57, 74).

– Light orange when the clogging of the filter is

detected or the filter counter reaches a time set

in the timer setting, urging immediate filter/ filter

cartridge replacement (pp.56, 57, 74).

yLAMP 2 REPLACE indicator

Turn orange when the life of the projection lamp2

draws to an end (pp.61, 73).

tSHUTTER indicator

Light blue when the shutter is closed (p72).

Remote Control

Part Names and Functions

q

t

e

!0

i

!4

r

!3

!1

w

y

u

o

!7

!2

!8

!9

@0

e

LIGHT button

Light the buttons on the remote control for about 10

seconds.

r

MENU button

Open or close the On-Screen MENU (pp.25-26).

t POINT ed 7 8 buttons

– Select an item or adjust the value in The ON-SCREEN MENU (p.25).

–Pan the image in DIGITAL ZOOM + mode (p.40).

y

LENS SHIFT button

Select the LENS SHIFT function (p.29).

u

FOCUS buttons

Adjust the focus (p.29).

i

ZOOM buttons

Zoom in and out the images (p.29).

o

FREEZE button

Freeze the picture on the screen (p.29).

!1

P-TIMER button

Operate the P-TIMER function (p.30).

!2

KEYSTONE button

Correct keystone distortion (pp.30, 40, 44).

q

ON/STAND-BY button

Turn the projector on or off (pp.23-24).

w

AUTO PC button

Automatically adjust the computer image to its optimum

setting (pp.29, 35).

!4

SHUTTER button

Close the built-in shutter for light blocking (pp.27, 30).

!5

SELECT

button

–Execute the selected item (p.25).

– Expand or compress the image in the DIGITAL ZOOM mode

(p.40).

@1

Wired Remote Jack

Connect the

remote control cable (supplied) to this jack when

using as a wired remote control.

@0

IMAGE SEL. button

Select the image level (pp.30, 38, 42).

!8

INPUT 1, 2, 3, 4

button

s

Select an input source (pp.31-33).

!7

IMAGE ADJ. button

Enter the image level adjustment mode (pp.30, 45-47).

!9 INFO. button

Display the input source information (p.29).

!6 SCREEN button

Select the screen size (pp.39-40).

!0D.ZOOM

button

Select the Digital zoom +/- mode and resize the image (pp.29, 40).

14

✔Note:

To ensure safe operation, observe the

following precautions:

• Do not bend, drop, or expose the remote

control to moisture or heat.

• For cleaning, use a soft dry cloth. Do not

apply benzene, thinner, spray, or any other

chemical materials.

!3FILTER button

Scroll the filter (p.30).

@1

!5

!6

Remote Control Battery Installation

1 2 3

Open the battery

compartment lid.

Install new batteries into

the compartment.

Replace the

compartment lid.

Two AA size batteries

For correct polarity (+ and –),

be sure battery terminals are

in contact with pins in the

compartment.

To ensure safe operation, please observe the following precautions :

l Use two (2) AA or LR6 type alkaline batteries.

l Always replace batteries in sets.

l Do not use a new battery with a used battery.

l Avoid contact with water or liquid.

l Do not expose the remote control to moisture or heat.

l Do not drop the remote control.

l If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

l Risk of an explosion if battery is replaced by an incorrect type.

l Dispose of used batteries according to the instructions.

Point the remote control toward the projector (to

Infrared Remote Receivers) when pressing the buttons.

Maximum operating range for the remote control is

about 16.4’ (5 m) and 60 degrees in front and rear of the

projector.

Infrared Remote Receivers are provided both in front and

back of the projector. You can conveniently use both of

the receivers (pp. 10, 52).

16.4’

(5 m)

Remote Control Receivers and Operating Range

The remote control can be used as a wired remote control. Wired remote control helps you use the remote control outside

of the operating range (16.4’/ 5 m). Connect the remote control and the projector with the remote control cable (supplied).

Connected with the remote control cable, the remote control does not emit wireless signal.

Wired Remote Control

Part Names and Functions

16.4’

(5 m)

15

Pull up the lid

and remove it.

✔Note:

•

When hanging the projector from the ceiling, select the

Infrared Remote Receiver which is located farther away

from the fluorescent light (p.52).

16

The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the remote

control codes prevents interference from other remote controls when several projectors or video equipment

next to each other are operated at the same time. Change the remote control code for the projector first before

changing that for the remote control. See “Remote control” in the Setting Menu on page 52.

1

2

Remote Control Code

Part Names and Functions

Flip the Reset Switch to "Use position" in the

compartment lid on the back of the remote control.

While holding down the MENU button, press

and release the IMAGE ADJ. button the number

of corresponding times you would like to set the

number of the remote control code for the projector.

Remote Control Code

Number of Times

Pressing IMAGE ADJ.

button

Code 1 1

Code 2 2

Code 3 3

Code 4 4

Code 5 5

Code 6 6

Code 7 7

Code 8 8

Reset position

Use position

IMAGE ADJ.

button

MENU button

Reset switch

17

Installation

Lens Installation

Before setting up the projector, install Projection Lens on the projector.

Before installation, check where the projector is used and prepare a suitable lens. For the specifications of

Projection Lens, contact sales dealer where you purchased the projector.

- Do not use the optional lens below for this projector. Otherwise damages may result.

LENS MODEL NO. : AH-21031, AH-21032

- Lens installation and replacement should be made by the qualified service personnel.

- When setting the projector after lens installation, be sure to replace a Lens Cap to protect a

surface.

- When carrying or holding up the projector, be careful not to put your hands on lens part. It may

damage lens, cabinet, or mechanical parts.

Installing the Strap for safety

Secure the lens mount cover and the projector with the

strap (supplied) to prevent the lens mount cover from

falling down.

Fig. 1

Screw A

Fig. 3

Label

Dot on the cabinet

Dot on the lens

mount cover

Strap

Remove the screw A. (See Fig. 1)

Turn the lens mount cover counter-clockwise and

take it off by pulling forward. (See Fig. 1)

1

2

Fit the raised dot of the lens mount cover to the

leftmost edge of the Label on the projector, and

then turn the lens mount cover clockwise and

adjust the position of the raised dot to the one of

the projector until it makes a clicking sound. (See

Fig. 3)

Put the strap through the hole of the lens mount

cover and fasten it ﬁrmly. (See Fig. 2)

3

5

Fig. 2

Strap

Lens Mount Cover

Screw A

Install the other end of the strap to the front of

the projector with screw A. (See Fig. 3)

4

✔Note:

• The accessory screw (supplied) is not used for installation.

Lens Mount Cover

Hole

18

Installation

Picture Level and Pitch Adjustment

ADJUSTABLE

FEET

REAR ADJUSTABLE

FEET (Refer to p.10)

Projection lens can be moved from side to side and up and down with the motor-driven lens shift function. This

function makes the positioning of images easy on the screen.(See page 27)

Lens Shift Adjustment

When the lens is shifted to top.

The display position can be

shifted upward up to 50%

elevation of the display.

When the lens is shifted to bottom.

The display position can be

shifted downward up to 50%

low level of the display.

When the lens is shifted to leftmost.

The display position can be

shifted to the left in up to

10% width of the display.

When the lens is shifted to rightmost.

The display position can be

shifted to the right in up to

10% width of the display.

The projection angle is adjustable up to 2.8 degrees

upward and downward respectively by rotating front and

back feet .

To raise the projector, rotate the feet clockwise.

To lower the projector or to retract the adjustable feet,

rotate the feet counterclockwise.

To correct keystone distortion, press the KEYSTONE

button on the remote control or select Keystone from the

menu (see pages 14, 30, 40, 44).

Do not rotate the adjustable feet when you

see the red line on the adjustable feet. The

adjustable feet may fall off.

Positioning Projector

This projector is designed to project on a flat projection

surface.

✔Note:

•

Brightness in room has a great influence on picture quality.

It is recommended to limit ambient lighting in order to

provide the best image.

SCREEN

19

Terminals of Projector

The projector has two replaceable Interface board slots. The projector's functions can be extended by installing

the optional interface boards into the terminal slots. 2 vacant slots (Input 3 and 4) are provided in your

purchasing the projector. For the Optional Interface Boards, contact sales dealer where you purchased the

projector.

Pull out the interface board.

Remove 2 Screws from an interface board.

1

2

Tighten screws to secure the interface board.

Replace the interface board. Insert a new interface

board along Guide to ﬁt Socket to inside Plug.

3

4

INPUT/OUTPUT

TERMINALS

Guide

Socket

Plug

Figure shows Dual-SDI terminal.

DVI / D-sub 15 Terminal 5-BNC / VideoTerminal

2 TERMINAL SLOTS (Factory set)

NOTES ON ORDERING OR USING

OPTIONAL INTERFACE BOARD

When ordering or using Optional Interface Board, contact

your sales dealer. When contacting the sales dealer, tell the

Option Control Number (Op.cont.No.) in the menu that is

located on the bottom of the information menu.

(See page 28)

✔Note:

• In the replacement of interface board, turn off the

projector, press the Main On/Off Switch to Off and

unplug the AC power cord from the AC outlet.

Replacement of Terminal

Installation

Screws

Page is loading ...

Eiki LC-X800 User manual

This manual is also suitable for

Eiki LC-X800 User manual

Related papers

Other documents