red roo GT622 Safety Precautions And Operating Instructions
- Category
- Mini tillers
- Type
- Safety Precautions And Operating Instructions
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) Wheninposition to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT5
GARDEN
TILLER
OPERATION OF GT622
1) Remove the garden tiller
from its trailer/carrier/ute. Use caution.
2) Familiarize yourself with the machine and its
controls.
5) Ensure the tyne engagement control lever is in
the neutral position. The tyne engagement
control lever is located
machine below handle bar. The neutral position
on the left hand side of the
of the lever is achieved by simply releasing the
tyne engagement control lever.
4)
3) Adjust wheels if required, using the handle wheel
adjustment lever.
Adjust depth shoe if required, using the depth
control adjustment lever.
6) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
pull up on the tyne engagement control lever.
The tynes will begin to turn. Release the tyne
7) Wheninposition to begingarden tilling,
engagement control lever to stop the tynes turning.
Tyne speed is governed by engine throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
8) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed. Consider
watering the surface and reducing engine speed.
Adjust wheels and depth shoe accordingly while
tilling
WARNING! –IN CASE OF DIFFICULTY,
RELEASE THE TYNE ENGAGEMENT
CONTROL LEVER. ALL TILLING ACTION
STOPS.Turn the engine "STOP" switch
to off located on the engine.
9) Stop Engine: Release the tyne engagement
control lever. Move throttle to Slow position.
Set engine stop switch to Stop or Off position.
DO NOT move choke
position to stop engine.
Backfire or engine
damage may occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheels and depth control handle to
transport position.
© Copyright 2012, Red Roo Sales & Service Company Pty. Ltd. 1301-0069-A
Commer
“The Right Way to Rent”
cial Outdoor Power Equipment
control to Choke or Start
You alone know the operational demands and
special conditions affecting the equipment in
your situation and therefore assume the
responsibility for developing, carrying out, and
enforcing the safety concepts which apply to your
own operation to effect the greatest safety for
yourself and the people around you.
Online Demonstration Available at:
www.redroo.com/products/rotaryhoe
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) Wheninposition to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) Wheninposition to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) Wheninposition to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
OPERATING
INSTRUCTIONS
BEFORE USE
1) Ensure that all grass and weeds have been
cut as low as possible.
2) If the garden tiller is to be used in clay or
hard ground conditions, it is recommended
to water the area thoroughly and allow
sufficient time for the soil to soften.
3) Police the area. Remove any foreign objects
from the area.
4) Identify and mark the location of sprinkler
heads, gas pipes, telephone cables, etc.
Digging
Zone
Depth
Control
Bar
Wheel Axle
Pivot
Safety Clutch
Control Lever
Engine
Lifting
Hook
You alone know the operational demands and
special conditions affecting the equipment in
your situation and therefore assume the
responsibility for developing, carrying out, and
enforcing the safety concepts which apply to your
own operation to effect the greatest safety for
yourself and the people around you.
“STAY ALERT – DON’T GET HURT”
USE COMMON SENSE
AND PLENTY OF IT
1) DO NOT allow any person to operate
the garden tiller without first reading
and understanding the safety
precautions and operating instructions.
KNOW THE CONTROLS AND HOW TO
STOP THE GARDEN TILLER QUICKLY IN
AN EMERGENCY.
2) NEVER allow children to operate the garden tiller.
3) ALWAYS wear protective clothing when
operating the garden tiller. This includes, but
is not limited to: safety glasses, loose fitting
gloves, steel capped boots and hearing
protection. NEVER wear loose fitting clothing
or jewellery when operating the garden tiller.
Keep all clothing away from moving parts.
Items could become
caught in the machine,
resulting in injury.
4) ALWAYS operate the garden tiller in a well lit area.
5) ALWAYS make certain that the tyne engagement
control lever is in the "neutral" position prior to
starting the engine. The TYNE ENGAGEMENT
CONTROL LEVER on the left handlebar is for the
operator’s protection. All motion stops when the
control lever’s released!
DO NOT TAPE THE CONTROL LEVER UP
or otherwise by-pass this safety feature!
6) ALWAYS operate garden tiller on level ground
only. Police the area before garden tilling.
Remove any foreign objects in the digging area
eg bricks, rocks, wire and sticks. Locate and
mark any sprinkler heads, water pipes, gas
lines, electrical and telephone cables or any
other hazard either below or above ground.
8) NEVER operate the garden tiller when
fatigued. ALWAYS BE ALERT! If you get
tired while operating the garden tiller, take a
break. If you have any type of physical or
mental condition that may be aggravated by
strenuous work, consult with your physician
before you operate this equipment. NEVER
operate the garden tiller under the influence of
medication, alcohol or drugs.
Hydraulic oil is under extreme pressure
and can get under skin and burn or poison.
Check for leaks with cardboard.
9)
11) NEVER operate the unit without the safety
guards in place and in working order. Keep
the unit well maintained and in good working
order
12) DO NOT leave the machine unattended while
the engine is running.
13) DO NOT overspeed the engine or alter the
governor settings. Excessive speed is
dangerous and will shorten engine life.
15) STOP the engine and disconnect the
spark plug lead(s) and allow engine
to cool before inspecting or
performing maintenance on the garden tiller.
16) REFUELLING
* Shut off engine. DO NOT REFUEL
AN ENGINE WHILE OPERATING!
* Allow engine to cool. Minimum 5 minutes.
*USE UNLEADED FUEL ONLY. Use clean,
fresh unleaded fuel.
*Do not mix oil with unleaded fuel.
* Do not over-fill fuel tank. Allow space for fuel
expansion.
* Do not smoke.
* Allow no naked flame or hot material in
refuelling area.
* Use only approved fuel containers and
funnels. Remember, fuel is a potential
hazard.
SAFETY PRECAUTIONS FOR GT622 USERS
10) ALWAYS KEEP YOUR HANDS,
FEET AND BODY AWAY FROM
THE DIGGING AREA WHILE
ENGINE IS RUNNING.
14) NEVER operate the garden tiller in
an enclosed area. Engine exhaust
contains carbon monoxide, an
odourless and tasteless poison.
7) DO NOT allow other persons near the garden tiller.
It is up to the operator to keep bystanders
and animals a minmum of 6 metres away
from the machine while in operation.
USE COMMON SENSE
AND PLENTY OF IT
1) DO NOT allow any person to operate
the garden tiller without first reading
and understanding the safety
precautions and operating instructions.
KNOW THE CONTROLS AND HOW TO
STOP THE GARDEN TILLER QUICKLY IN
AN EMERGENCY.
2) NEVERallow children to operate the garden tiller.
3) ALWAYS wear protective clothing when
operating the garden tiller. This includes, but
is not limited to: safety glasses, loose fitting
gloves, steel capped boots and hearing
protection. NEVER wear loose fitting clothing
or jewellery when operating the garden tiller.
Keep all clothing away from moving parts.
Items could become
caught in the machine,
resulting in injury.
4) ALWAYS operate the
garden tiller in a well lit area.
5) ALWAYS make certain that the safety clutch
control lever is in the "disengaged" position
prior to starting the engine.
6) ALWAYS operate garden tiller on level ground
only. Police the area before garden tilling.
Remove any foreign objects in the digging area
eg bricks, rocks, wire and sticks. Locate and
mark any sprinkler heads, water pipes, gas
lines, electrical and telephone cables or any
other hazard either below or above ground.
7) DO NOT allow other persons near the garden
tiller. It is up to the operator to keep bystanders
and animals a minimum of 6 metres away from
the machine while in operation.
8) NEVER operate the garden tiller when
fatigued. ALWAYS BE ALERT! If you get
tired while operating the garden tiller, take a
break. If you have any type of physical or
mental condition that may be aggravated by
strenuous work, consult with your physician
before you operate this equipment. NEVER
operate the garden tiller under the influence of
medication, alcohol or drugs.
9) ALWAYS KEEP YOUR HANDS,
FEET AND BODY AWAY FROM
THE DIGGING AREA WHILE
ENGINE IS RUNNING.
10) NEVER operate the unit without the safety
guards in place and in working order. Keep
the unit well maintained and in good working
order
11) DO NOT leave the machine unattended while
the engine is running.
12) DO NOT overspeed the engine or alter the
governor settings. Excessive speed is
dangerous and will shorten engine life.
13) NEVER operate the garden tiller in
an enclosed area. Engine exhaust
contains carbon monoxide, an
odourless and tasteless poison.
14) STOP the engine and disconnect the
spark plug lead(s) and allow engine
to cool before inspecting or
performing maintenance on the garden tiller.
15) REFUELLING
* Shut off engine. DO NOT REFUEL
AN ENGINE WHILE OPERATING!
* Allow engine to cool. Minimum 5 minutes.
*USE UNLEADED FUEL ONLY. Use clean,
fresh unleaded fuel.
*Do not mix oil with unleaded fuel.
* Do not over-fill fuel tank. Allow space for fuel
expansion.
* Do not smoke.
* Allow no naked flame or hot material in
refuelling area.
* Use only approved fuel containers and
funnels. Remember, fuel is a potential
hazard.
SAFETY PRECAUTIONS FOR GT5 USERS
OPERATING
INSTRUCTIONS
BEFORE USE
1) Ensure that all grass and weeds have been
cut as low as possible.
2) If the garden tiller is to be used in clay or
hardgroundconditions, it is recommended
to water the area thoroughlyandallow
sufficient time for the soil to soften.
3) Police the area. Remove any foreign objects
from the area.
4) Identify andmark the location of sprinkler
heads, gas pipes, telephone cables, etc.
Digging
Zone
Depth
Control
Bar
Wheel Axle
Pivot
Safety Clutch
Control Lever
Engine
Lifting
Hook
Youaloneknowtheoperationaldemandsand
special conditionsaffectingtheequipment in
your situationandtherefore assumethe
responsibilityfordeveloping,carryingout,and
enforcingthesafetyconceptswhichapply to your
ownoperation to effectthegreatestsafetyfor
yourself and the people around you.
“STAY ALERT – DON’T GET HURT”
USE COMMON SENSE
AND PLENTY OF IT
1) DO NOT allow any person to operate
the garden tiller without first reading
and understanding the safety
precautions and operating instructions.
KNOW THE CONTROLS AND HOW TO
STOP THE GARDEN TILLER QUICKLY IN
AN EMERGENCY.
2) NEVER allow children to operate the garden tiller.
3) ALWAYS wear protective clothing when
operating the garden tiller. This includes, but
is not limited to: safety glasses, loose fitting
gloves, steel capped boots and hearing
protection. NEVER wear loose fitting clothing
or jewellery when operating the garden tiller.
Keep all clothing away from moving parts.
Items could become
caught in the machine,
resulting in injury.
4) ALWAYS
5) ALWAYS make certain that the tyne engagement
control lever is in the "neutral" position
prior to starting the engine.
6) ALWAYS operate garden tiller on level ground
only. Police the area before garden tilling.
Remove any foreign objects in the digging area
eg bricks, rocks, wire and sticks. Locate and
mark any sprinkler heads, water pipes, gas
lines, electrical and telephone cables or any
other hazard either below or above ground.
7) DO NOT allow other persons near the garden tiller.
It is up to the operator to keep bystanders
and animals a minimum of 6 metres away
from the machine while in operation.
8) NEVER operate the garden tiller when
fatigued. ALWAYS BE ALERT! If you get
tired while operating the garden tiller, take a
break. If you have any type of physical or
mental condition that may be aggravated by
strenuous work, consult with your physician
before you operate this equipment. NEVER
operate the garden tiller under the influence of
medication, alcohol or drugs.
Hydraulic oil is under extreme pressure and can
get under skin and burn or poison. Check for
leaks with cardboard.
10)
9)
ALWAYS KEEP YOUR HANDS,
FEET AND BODY AWAY FROM
THE DIGGING AREA WHILE
ENGINE IS RUNNING.
11) NEVER operate the unit without the safety
guards in place and in working order. Keep
the unit well maintained and in good working
order
12) DO NOT leave the machine unattended while
the engine is running.
13) DO NOT overspeed the engine or alter the
governor settings. Excessive speed is
dangerous and will shorten engine life.
14) NEVER operate the garden tiller in
an enclosed area. Engine exhaust
contains carbon monoxide, an
odourless and tasteless poison.
15) STOP the engine and disconnect the
spark plug lead(s) and allow engine
to cool before inspecting or
performing maintenance on the garden tiller.
16) REFUELLING
* Shut off engine. DO NOT REFUEL
AN ENGINE WHILE OPERATING!
* Allow engine to cool. Minimum 5 minutes.
*USE UNLEADED FUEL ONLY. Use clean,
fresh unleaded fuel.
*Do not mix oil with unleaded fuel.
* Do not over-fill fuel tank. Allow space for fuel
expansion.
* Do not smoke.
* Allow no naked flame or hot material in
refuelling area.
* Use only approved fuel containers and
funnels. Remember, fuel is a potential
hazard.
SAFETY PRECAUTIONS FOR GT622 USERS
OPERATING
INSTRUCTIONS
BEFORE USE
1) Ensure that all grass and weeds have been
cut as low as possible.
2) If the garden tiller is to be used in clay or
hard ground conditions, it is recommended
to water the area thoroughly and allow
sufficient time for the soil to soften.
3) Police the area. Remove any foreign objects
from the area.
4) Identify and mark the location of sprinkler
heads, gas pipes, telephone cables, etc.
You alone know the operational demands and
special conditions affecting the equipment in
your situation and therefore assume the
responsibility for developing, carrying out, and
enforcing the safety concepts which apply to your
own operation to effect the greatest safety for
yourself and the people around you.
“STAY ALERT – DON’T GET HURT”
operate the garden tiller in a well lit area.
OPERATOR ZONE
Tyne Engagement Control Lever
Forward / Neutral / Reverse
(Operator Presence Control)
Lifting Hook
Engine
Bumper
Bar
Wheel
Axle Pivot Lever
(located on
other side of machine)
DIGGING ZONE
Depth
Control
Bar Lever
-
1
-
2
red roo GT622 Safety Precautions And Operating Instructions
- Category
- Mini tillers
- Type
- Safety Precautions And Operating Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Troy-Bilt 654J User manual
-
-
Mantis 7222 SV4 Owner's manual
-
Bolens 12060 User manual
-
MTD 390 Series User manual
-
Cub Cadet Series 390 User manual
-
Troy-Bilt 15006 User manual
-
-
-
Yard-Man 21A-392B401 User manual