Curt Manufacturing 11574 Owner's manual

Curt Manufacturing
Brand
Curt Manufacturing
Model
11574
Type
Owner's manual

Curt Manufacturing 11574 is a weight-carrying hitch with a gross load capacity of 1,000 lbs. and a tongue weight of 100 lbs. It is designed to be used with a 4-door Honda Civic wagon manufactured between 1984 and 1987. The hitch is constructed from durable materials and features a .250" backing plate for added strength. It also includes all necessary hardware for installation, including 3/8" fasteners, fender washers, and a silicone sealant to ensure a weather-tight fit.

The Curt Manufacturing 11574 is easy to install, with a professional installation time of 45 minutes and a novice installation time of 90 minutes. It requires drilling for installation, so it is important to clear the trunk before beginning. Once installed, the hitch can be used to tow trailers or carry other heavy loads.

Curt Manufacturing 11574 is a weight-carrying hitch with a gross load capacity of 1,000 lbs. and a tongue weight of 100 lbs. It is designed to be used with a 4-door Honda Civic wagon manufactured between 1984 and 1987. The hitch is constructed from durable materials and features a .250" backing plate for added strength. It also includes all necessary hardware for installation, including 3/8" fasteners, fender washers, and a silicone sealant to ensure a weather-tight fit.

The Curt Manufacturing 11574 is easy to install, with a professional installation time of 45 minutes and a novice installation time of 90 minutes. It requires drilling for installation, so it is important to clear the trunk before beginning. Once installed, the hitch can be used to tow trailers or carry other heavy loads.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
1,000 100
8
45
84-87 HONDA CIVIC 4 DOOR WAGON ONLY
4/5/2010
11574
90
217282
Parts List DESCRIPTION
PART NUMBER
QTY
ITEM HEX BOLT3/8 - 16 x 1 1/431 LOCK WASHER3/8"
5
2HEX NUT3/8 - 16
5
3HEX BOLT3/8-16 X 1 1/224 FENDER WASHER3/8"2
5.250" BACKING PLATECM-11574-BP
16
1. Locate and mark the vehicle's centerline at the floor and the rear panel. Clear the trunk to permit
drilling for the hitch.
2. Position the hitch centered and square with the vehicle against the trunk floor and the rear panel.
Note that the hitch bracket slides under a metal edge to mate with the rear panel. Using the hitch as a
template, mark and drill (5) holes for 3/8" fasteners; (3) in the rear panel and (2) in the trunk floor.
3. Fasten the hitch to the vehicle using fasteners as shown. Be sure to use the CM-11574-BP backing plate
inside the rear panel and fender washes inside the trunk floor.
4. Torque all 3/8" fasteners to 30 lb-ft.
5. Use silicone sealant to seal hardware installed through trunk floor and rear panel.
6. Reinstall contents removed from trunk in Step 1.
32
4
51
SLIDE HITCH
UNDER METAL FLANGE
TRUNK FLOOR
- DRILLING REQUIRED
- CLEAR TRUNK
- SILICONE SEAL HARDWARE
6
REAR PANEL
  • Page 1 1

Curt Manufacturing 11574 Owner's manual

Curt Manufacturing
Brand
Curt Manufacturing
Model
11574
Type
Owner's manual

Curt Manufacturing 11574 is a weight-carrying hitch with a gross load capacity of 1,000 lbs. and a tongue weight of 100 lbs. It is designed to be used with a 4-door Honda Civic wagon manufactured between 1984 and 1987. The hitch is constructed from durable materials and features a .250" backing plate for added strength. It also includes all necessary hardware for installation, including 3/8" fasteners, fender washers, and a silicone sealant to ensure a weather-tight fit.

The Curt Manufacturing 11574 is easy to install, with a professional installation time of 45 minutes and a novice installation time of 90 minutes. It requires drilling for installation, so it is important to clear the trunk before beginning. Once installed, the hitch can be used to tow trailers or carry other heavy loads.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents