WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL: WHLD
1
6900-230-001
NEW: 02/08/23
R e m o v e S t a i n l e s s S t e e l
Fasteners and Drain Cover. Set
aside for later installation.
1
Prior to pouring concrete floor
slab or constructing alternate
flooring structure: Position Drain
Body Assembly at desired location
atop “sub-floor structure” and
aligned with 2” IPS Drainpipe.
Make up 2” IPS (2-3/8” OD) No-
Hub Waste Connection: Use
a p p r op ri a te Ba nd C o u pl in g
(Provided By Others) to ensure
connection does not leak.
3
PRE-COAT THE LAY-OUT AREA:
Using Water Proofing Compound
across the designated floor area
and side walls.
2
D e t ai l s l is te d
below for installation of Flooring
are provided as reference only.
Installer shall follow Industry
Standards of Practice which are
best suited for the site conditions
and materials being used.
NEW: 02/08/23
CONCRETE
SHOWN FOR
REF. ONLY
WATER PROOFING
COMPOUND
2” IPS
DRAIN OUTLET
BRACKET CHANNEL
SUPPORT
DRAIN BODY
ASSEMBLY
DRAIN COVER
ASSEMBLY
VANDAL RESISTANT,
COUNTERSUNK,
STAINLESS STEEL
FASTENERS
DRAIN PIPE BAND COUPLING
(BY OTHERS)
2" IPS
DRAIN
OUTLET
WHITEHALL MFG MODEL WHLD LIGATURE RESISTANT LINEAR DRAIN
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE
NUMBER: 1.800.591.9360
NOTES TO THE INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing and other applicable codes.
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL: WHLD
2
6900-230-001
NEW: 02/08/23
4Prep unfinished floor as required to receive
Sub-Floor: Pour the Floor Screed Compound,
pack underneath the Drain Body. And screed from
the bottom to the top of the Drain Flange.
Complete construction of sub-flooring structure.
NOTE: Use Level to make sure Drain Body is
positioned properly.
DRAIN BODY SUB-FLOOR
Top Flashing Flange must be
flushed to Screed Compound for proper
installation.
SUB-FLOOR
FINISHED
TOP FLASHING FLANGE
SUB-FLOOR
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
INSTALLATION, OPERATION & MAINTENANCE MANUAL MODEL: WHLD
3
6900-230-001
NEW: 02/08/23
Install Drain Cover: Position Drain
Cover [”into” or “inside”] the Drain
Body Assembly and screw Drain
Cover using the Fasteners Screws
provided.
Note: Using a socket wrench, tighten
Fa s t en er s f ro m in s i de t o o u t ,
alternating sides and repeating the
process until all screws are tight. do
not over tighten.
7
5Prep pre-finished floor as required
to Waterproofed Sub-Floor: Once
Screen Compound has dried. Apply
w a t e r p r o o fi n g c o m p o u n d P e r
Manufacturers recommendations and
to meet code standards.
Note: Carefully not to cover Drain
Holes during layer coating.
Install Tiles: Once Waterproof
Compound has completely
dried complete Flooring as
required. (Install Tiling etc.)
6
FINISHED TILE
DRAIN COVER
ASSEMBLY
VANDAL RESISTANT,
COUNTERSUNK,
STAINLESS STEEL
FASTENERS
DRAIN BODY
ASSEMBLY
FINISHED
TILE
Details listed below for installation of
Flooring are provided as reference only. Installer shall
follow Industry Standards of Practice which are best
suited for the site conditions and materials being used.
WATER PROOFING
COMPOUND
SUB-FLOOR
WATER PROOFING
COMPOUND
DRAIN BODY
(MEMBRANE) AS
REQUIRED TO
SUIT SITE
CONDITIONS.
/
