GE AHD06LZ Owner's manual

Brand: GE

Model: AHD06LZ

Type: Owner's manual

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find the rating label on the

side of the air conditioner.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

AIR CONDITIONER

ROOM

49-7778-2 09-19 GEA

SAFETY INFORMATION .........3

USING THE AIR CONDITIONER

Controls ..............................4

CARE AND CLEANING ...........8

INSTALLATION INSTRUCTIONS

Before you begin ......................9

Electrical Requirements ................9

Parts Included ........................10

Window Requirements ................ 11

Prepare the Air Conditioner ............ 11

Install the Air Conditioner ..............12

TROUBLESHOOTING TIPS ......14

Normal Operating Sounds .............15

CONSUMER SUPPORT

Limited Warranty .....................17

Consumer Support ....................18

AHD06

AHD08

2 49-7778-2

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-7778-2 3

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of

fire, electric shock or personal injury.

Ŷ8VHWKLVDSSOLDQFHRQO\IRULWVLQWHQGHGSXUSRVHDV

described in this Owner’s Manual.

ŶThis air conditioner must be properly installed in

accordance with the Installation Instructions before it is

used.

ŶNever unplug your air conditioner by pulling on the

power cord. Always grip plug firmly and pull straight

out from the receptacle.

ŶReplace immediately all electric service cords that

have become frayed or otherwise damaged. A

damaged power supply cord must be replaced with a

new power supply cord obtained from the manufacturer

and not repaired. Do not use a cord that shows cracks

or abrasion damage along its length or at either the

plug or connector end.

ŶTurn the unit OFF and unplug your air conditioner

before cleaning.

ŶFor your safety…do not store or use combustible

materials, gasoline or other flammable vapors or

liquids in the vicinity of this or any other appliance.

ŶIf the receptacle does not match the plug, the

receptacle must be changed out by a qualified

electrician.

Ŷ'RQRWXVHPHDQVWRDFFHOHUDWHWKHGHIURVWLQJSURFHVV

or to clean, other than those recommended by the

manufacturer.

ŶThe appliance shall be stored in a room without

continuously operating ignition sources (for example:

open flames, an operating gas appliance or an

operating electric heater.

ŶDo not pierce or burn refrigerant tubing. Be aware that

refrigerants may not contain an odor.

ŶKeep ventilation openings clear of obstruction.

ŶWhen handling, installing, and operating the appliance,

care should be taken to avoid damage to the

refrigerant tubing.

ŶDo not drill holes in the unit.

ŶMaintenance, cleaning, and service should only be

performed by technicians properly trained and qualified

in the use of flammable refrigerants.

ŶGE Appliances does not support any servicing of the

air conditioner.

ŶDispose of air conditioner in accordance with Federal

and Local Regulations. Flammable refrigerants require

special disposal procedures. Contact your local

authorities for the environmentally safe disposal of your

air conditioner.

WARNING

Risk of Fire or Explosion. This unit contains flammable refrigerant.

Additional safety precautions must be followed.

4 49-7778-2

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

READ AND SAVE THESE INSTRUCTIONS

WARNING

USE OF EXTENSION CORDS

RISK OF FIRE. Could cause serious injury or death.

Ŷ'2127XVHDQH[WHQVLRQFRUGZLWKWKLV:LQGRZ$LU

Conditioner.

Ŷ'2127XVHVXUJHSURWHFWRUVRUPXOWLRXWOHWDGDSWRUV

with this Window Air Conditioner.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord. For personal safety,

this appliance must be properly grounded.

DO NOT use an adapter plug with this appliance.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility

of electric shock hazard from this appliance.

Power cord includes a current interrupter device. A test

and reset button is provided on the plug case. The device

should be tested on a periodic basis by first pressing the

TEST

button and then the RESET button while plugged

into the outlet. If the TEST button does not trip or if the

RESET button will not stay engaged, discontinue use of the

air conditioner and contact a qualified service technician.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a 2-prong wall outlet is encountered, it is your

personal responsibility and obligation to have it replaced

with a properly grounded 3-prong wall outlet.

The air conditioner should always be plugged into its

own individual electrical outlet which has a voltage rating

that matches the rating plate.

This provides the best performance and also prevents

overloading house wiring circuits which could cause a

fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical connection

requirements.

49-7778-2 5

USING THE AIR CONDITIONER

Controls

This section explains how to operate this air conditioner.

IMPORTANT:

When you turn off the air conditioner, either at the control

panel or with the remote control, wait at least 3 minutes

before turning it back on. This prevents the compressor

from overloading. This 3 minute delay also applies when

switching from cool mode to fan and back.

NOTE: There is a built in 3 minute delay. You may notice

the compressor might not start right away. This was

designated to protect the unit.

Do not operate your air conditioner in the Cool Mode when

the outside temperature is below 61° F (16° C). This inside

evaporator coil will freeze up, and the air conditioner will not

operate properly.

NOTE: When the air conditioner is first plugged in, the

LED display will show “88” for 3 seconds. After the air

conditioner is turned on for the first time, the display will

show the temperature 72° F and the fan will automatically

set the Quiet speed and the Mode indicator will show

ENERGY SAVE.

NOTE: To switch the temperature display between

Fahrenheit (°F) and Celsius (°C), the air conditioner must

be plugged in and turned on. On the control panel on the

IURQWRIWKHDLUFRQGLWLRQHUSUHVVWKH83DQG'2:1EXWWRQ

at the same time and hold for 3 seconds. Press F/C button

on remote control to switch between Fahrenheit (°F) and

Celsius (°C).

NOTE: Each time this ENERGY STAR qualified air

conditioner is turned on, it will operate in energy save mode

per the EPA requirements. You can select any other mode

to satisfy your needs.

Features and appearance will vary.

Temp.

Time

FAN

E-SAVE

COOL

DEHUM.

HIGH

MED

QUIET ON SLEEP CLEAN FILTER

OFF

MODE SPEED TIMER

FILTER

RESET

POWER

°F/°C

AUTO

Controls

1. MODE

1. Press MODE until you see the indicator light come on

next to the desired setting.

2. Choose Fan, Cool, Energy Save, or Dehum.

Fan - Only the fan runs. Press SPEED to select High,

Med or Quiet fan speed. The display shows the current

room temperature. NOTE: in fan mode, the temperature

cannot be set.

Energy Save - In this this mode the fan runs only when

cooling is needed. The fan will run for 3 minutes after

the compressor shuts off. The fan then cycles on for 2

minutes at 10 minute intervals until the temperature in

the room is above the set temperature. The compressor

then turns back on.

Cool - Cools the room. Press SPEED to select High,

Med, Quiet or Auto Cool fan speed. Press the TEMP/

TIME ޔ or ޕarrow button to adjust the temperature.

The fan will run continuously in cool mode.

Dehum - Aids in removing humidity from the room.

Dehum mode cannot be used to cool room.

NOTE: In Dehum mode, when the set temperature is

close to ambient temperature, the compressor may stop

and the fan will run in Quiet speed only.

2. SPEED

1. Press SPEED until you see the indicator light come

on next to the desired setting.

2. Choose High, Med, Quiet, or Auto Cool

HIGH - For maximum cooling.

MED - For normal cooling.

48,(7)RUPLQLPXPFRROLQJDQGQRLVH

$872&22/$GMXVWVWKHIDQVSHHGDXWRPDWLFDOO\WR

provide ideal cooling based on the room temperature.

6 49-7778-2

Controls

3. TIMER OFF

To set the air conditioner to turn off between 1 hour and

24 hours (the air conditioner must be ON to set).

1. Press TIMER button until Timer Off indicator light

illuminates. The display will show the remaining hours

before the air conditioner will turn off.

2. Press the TEMP/TIME

ޔ or ޕ arrow button to change

the delay time from 1 hour to 24 hours..

3. Timer Off indicator light will remain on. The display

will show the remaining time to Timer Off.

4. TIMER ON

To set the air conditioner to turn on between 1 hour and

24 hours.

1. Press TIMER button until Timer On indicator light

illuminates. The display will show the remaining hours

before the air conditioner will turn on.

2. Press the TEMP/TIME ޔ or ޕ arrow button to change

the delay time from 1 hour to 24 hours..

3. Timer On indicator light will remain on. The display

will show the remaining time to Timer On.

To clear TIMER Program:

NOTE: Air conditioner can be either on or off.

Press TIMER until Timer indicator light turns off.

To view or change the remaining time (in hours):

TIMER OFF -

1. Press the Temp Time ޔ or ޕarrows button to

increase or decrease the time.

2. The display will show the remaining time to Timer

OFF.

TIMER ON -

1. The display will show the remaining time.

2. Press the Temp Time ޔ or ޕ arrows button to

increase or decrease the time.

3. The display will show the remaining time to Timer ON.

NOTE: In TIMER and SLEEP mode, temperature cannot

be adjusted.

5. SLEEP

1. Press the TIMER button to choose Sleep mode. The

indicator light will turn on.

2. The temperature will increase by 2° F one hour after

the mode is chosen. The temperature then increases

another 2° F after one hour. The unit will hold this

temperature for six hours then stop.

3. To turn off Sleep mode, press the TIMER button until

the indicator light is off.

6. TEMP/TIME

1. Press the TEMP/TIME ޔ arrow button to raise the

temperature. Each time you press the TEMP/TIME up

arrow button, the temperature will go up by 1° F until it

reaches 86° F (30° C).

2. Press the TEMP/TIME ޕ arrow button to lower the

temperature. Each time you press the TEMP/TIME down

arrow button, the temperature will go down by 1° F until it

reaches 61° F (16° C).

NOTE8QGHU)DQPRGHWKHGLVSOD\ZLOOVKRZWKH

FXUUHQWWHPSHUDWXUH8QGHU(QHUJ\6DYH&RRORU

Dehum mode, the display will show the set temperature.

7. FILTER RESET

This feature automatically notifies you that the air filter

must be cleaned. The indicator light will come on after

240 hours of operation. Clean the air filter (refer to Care

and Cleaning section), place it back in the front panel,

and press the Filter Reset button. The light will turn off.

USING THE AIR CONDITIONER

49-7778-2 7

USING THE AIR CONDITIONER

Using the Remote Control

Remote Control may differ in appearance from the image

show.

NOTE: Please remove the back of the controller and insert

two AAA batteries. Replace batteries after 6 months of use

or when remote control starts to lose power.

NOTE: DO NOT mix old and new batteries.

1. POWER

Press the power button to turn on the air conditioner.

When you first press the power button, the air conditioner

will operate in Energy Save mode, Quiet fan speed and

temperature of 72°F. You can select any other mode to

satisfy your needs .

2. SPEED

High - Press HIGH button to choose high fan speed.

Med - Press MED button to choose medium fan speed.

Quiet3UHVV48,(7EXWWRQWRFKRRVHTXLHWIDQVSHHG

Auto Cool 3UHVV$872EXWWRQWRFKRRVHDXWRFRROIDQ

speed.

3. MODE

Fan- Press the FAN button to activate fan mode.

Cool - Press the COOL button to activate cool mode.

Energy Save Press the ENERGY SAVE button to

activate fan mode.

Dehum -3UHVVWKH'(+80EXWWRQWRDFWLYDWHGHKXP

mode.

4. TIMER

To set the air conditioner to turn off after a set

amount of time between 1 hour and 24 hours (unit

must be ON):

1. Press TIMER ON/OFF button on the remote control to

select the time off function.

3UHVVWKH7,0(583RU7,0(5'2:1DUURZEXWWRQ

to change the delay time from 1 hour to 24 hours. Timer

OFF indicator light on the air conditioner panel will

illuminate.

3. The buzzer beeps twice after 5 seconds, then Timer

OFF countdown will initiate.

To clear TIMER Program:

NOTE: Air conditioner can be either on or off.

Press TIMER ON/OFF button until Timer indicator light

turns off.

5. TEMP UP/TEMP DOWN

3UHVVWKH7(0383EXWWRQWRUDLVHWKHWHPSHUDWXUH

(DFKWLPH\RXSUHVVWKH7(0383EXWWRQWKH

temperature will go up 1° F until it reaches 86°F (30°C).

• Press the TEMP DOWN button to lower the

temperature. Each time you press the TEMP DOWN

button, the temperature will go down 1° F until it reaches

61°F (16°C).

6. SLEEP

1. Press SLEEP button on the remote control to choose

Sleep mode. This display will show (08) and the indicator

light will turn on.

2. The temperature will increase by 2° F one hour after

the mode is chosen. The temperature then increases

another 2° F after one hour. The until will hold this

temperature for six hours then stop.

3. To turn off Sleep mode, press the SLEEP button until

the indicator light is off.

7. FAHRENHEIT/CELSIUS

• Press the F/C button to choose between Fahrenheit

and Celsius.

8. LOCK

• Press the LOCK button on the remote control to

disable button functionality. Press the LOCK button

again to activate the remote control functionality.

9. LIGHT

• When you press the LIGHT button, the display on the

unit will turn off, but the unit is still operating normally.

When you press the LIGHT button again or press

any button on the remote control, the display will be

illuminated again.

10. RESET

• Press the RESET button to reset the unit to factory

settings.

DEHUM

TIMER

SLEEP

LOCK

TIMER

ON/OFF

F/C

TIMER

DOWN

LIGHT RESET

TEMP DOWN

QUIET

HIGH MED AUTO

COOLFAN

ENERGY

SAVE

TEMP UP

Controls

8 49-7778-2

Controls

USING THE AIR CONDITIONER

Air Direction

COOL MIN:

To reduce cooling capacity, point air directional louvers

up.

COOL MAX:

To maximize cooling capacity, point air directional

louvers down.

Changing the Air Direction

4-Way Air Flow: The air directional louvers let you

control the direction of the airflow. The airflow can be

directed up-down and left to right.

49-7778-2 9

CARE AND CLEANING

Care and Cleaning

Cleaning the Air Filter

The air filter is removable for easy cleaning. A clean air filter

helps remove dust, lint and particles from the air for optimal

cooling operating efficiency. The Filter Reset light will turn

on to notify you that the air filter must be cleaned. The light

goes on after the air conditioner has been operating for 240

hours.

1. Turn off the air conditioner and unplug the power supply

cord from the outlet.

2. Remove the air filter by opening the front panel and

removing the air filter. Some models may have a filter

that slides out instead and does not require opening of

the front panel.

8VHDYDFXXPFOHDQHUZLWKWKHKRVHDWWDFKPHQWWRFOHDQ

the air filter. If the air filter is very dirty, wash it in warm

water with mild detergent. Do not wash the air filter in

a dishwasher or clothes washer, or use any chemical

cleaners. Do not use a cloth dryer or microwave oven

to dry it. Air dry the air filter completely before placing it

back in the unit.

4. Place the air filter back in the air conditioner.

5. Close the front panel.

6. Plug the power supply cord into the outlet, turn on the air

conditioner and press the filter reset button to turn off the

indicator light.

NOTE: Do not operate the air conditioner without the filter

in place.

Cleaning the Front Panel

1. Turn off the air conditioner and unplug the power supply

cord from the outlet.

2. Clean the front panel with a soft cloth. Do not use

chemical cleaners, especially spray cleaners, sharp

instruments, or flammable fluids. These products can

damage the surface of your air conditioner.

3. Air-dry the front panel completely.

4. Plug the power supply cord in the outlet and turn on the

air conditioner.

10 49-7778-2

Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

 <RX0867XVHDOOVXSSOLHGSDUWVDQGXVHSURSHU

installation procedures as described in these

instructions when installing this air conditioner.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

These models require a 115/120-volt AC,

60-Hz grounded outlet protected with a

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility

of electric shock hazard. If the wall outlet you plan to

use is only a 2-prong outlet, it is your responsibility to

have it replaced with a properly grounded 3-prong wall

outlet.

CAUTION

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Do not change the plug on the power cord of this air

conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

Power cord includes a current interrupter device. A

test and reset button is provided on the plug case. The

device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button

while plugged into the outlet. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a

qualified service technician.

ELECTRICAL

REQUIREMENTS

WARNING

EXCESSIVE WEIGHT HAZARD - When moving or

lifting the air conditioner, use two or more people.

Wear gloves when handling the air conditioner to

protect against possible sharp edges and metal fins.

Remove Packaging Materials

• Remove packaging materials. Save the carton

and the foam packaging for storing the unit when

not in use.

NOTE: There is NO internal packing material

inside the air conditioner to remove - DO NOT

open the cabinet.

• Handle the air conditioner gently.

• Keep the air conditioner upright and level. Do not

set the air conditioner on its side, front, back or

upside down.

• The air conditioner must be standing upright for 2

hours prior to installation and operation.

UNPACKING THE AIR

CONDITIONER

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measurePencil

Level

Scissors or knife

Drill and 1/8” drill bit

INSTALLATION INSTRUCTIONS

49-7778-2 11

INSTALLATION INSTRUCTIONS

Installation Instructions

DEHUM

TIMER

SLEEP

LOCK

TIMER

ON/OFF

F/C

TIMER

DOWN

LIGHT RESET

TEMP DOWN

QUIET

HIGH MED AUTO

COOLFAN

ENERGY

SAVE

TEMP UP

Side Curtain

Frame

Type B (9)

1” wood screw

Weather Seal (3)

AHD06 only

Side

Curtain (2)

Top mounting rail

Air

conditioner

Window locking

bracket (1)

Side Brackets (2)

PARTS INCLUDED

(Appearance may vary)

Left

Right

Type A (4)

3/8” self-

tapping screw

Foam

Seal

Remote Control

Side Curtain

Foam (2)

AHD06 only

12 49-7778-2

Installation Instructions

3. PREPARE THE AIR CONDITIONER

A. Install the top mounting rail with 4 Type A screws

B. Slide the side curtain panels into the side panel

rails.

C. For model AHD06, cut and apply a weather

strip to side of the curtain frame (one each side).

D. Slide left and right side curtain frames into top

and bottom rails. Make sure that side curtains

snap into side of the frames.

1. WINDOW REQUIREMENTS

• These instructions are for a standard

double-hung window. You will need to modify

them for other types of windows.

• The air conditioner can be installed without the

side curtain panels if needed to fit in a narrow

window. See the window opening dimensions.

• All supporting parts must be secured to firm

wood, masonry or metal.

• The electrical outlet must be within reach of

the power cord.

• Follow the dimensions in the table and

illustration for your model.

2. STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and will

keep it from draining properly. To adjust for this,

attach a piece of wood to the sill.

WOOD PIECES

WIDTH: 2Ǝ

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place

DSLHFHRIZRRGRQWKHVLOOWRPDNHLWƎKLJKHU

than the top of the storm window frame or the

vinyl frame.

Attach securely with nails or screws provided by

the installer.

Vinyl frame

13 3/8”

(With side curtain panels)

26-1/16”- 39-1/4”

ƎKLJKHU

than storm

window

frame

Storm window

frame

Wood

Sill

ƎKLJKHU

than vinyl frame

(on some windows)

Top Mounting rail

CLICK

INSTALLATION INSTRUCTIONS

49-7778-2 13

INSTALLATION INSTRUCTIONS

Installation Instructions

4. INSTALL THE AIR CONDITIONER

IN THE WINDOW

A. Measure the width of the window opening and

mark the center line on the inside window sill.

For model AHD06:

Place the unit in the window. Lower the window

sash to hold unit in place.

B. Set the air conditioner in the window so that is

centered. Place the air conditioner so that front

edge of the bottom mounting rail is against the

back edge of the sill.

Make sure that the air conditioner is level or tilting

slightly to the outside.

Width of window opening

Center line

4. INSTALL THE AIR CONDITIONER

IN THE WINDOW (continues)

C. Install the side bracket into the unit and into the

window sill using two 1” wood screws provided.

Repeat on other side.

D. Extend the curtain panels until they fill the

window.

Mark the location of the holes in each corner of

WKHFXUWDLQ8VHWKHGULOODQG´GULOOELWWRGULOO

SLORWKROHV8VHW\SH%VFUHZVWRVHFXUHWKH

side panels in place.

Top Rail

Lower

Window Sash

Sill

Bottom Rail

Cut and apply weather

strip to front and

bottom edge of window

frame.

Cut and apply weather

strip to back edge of

the window sill

14 49-7778-2

Installation Instructions

INSTALLATION INSTRUCTIONS

5. INSTALL WINDOW LOCKING

BRACKET AND FOAM TOP

WINDOW GASKET

8VH7\SH%6FUHZWRLQVWDOOWKHZLQGRZORFN

bracket on top of the bottom window.

CAUTION

To prevent broken glass or

damage to windows, on vinyl

or other similarly constructed

windows, attach the window

locking bracket to the

window side jamb with one

Type B screw.

B. Cut the foam top window gasket to the window

width.

C. Stuff the foam between the glass and the window

to prevent air and insects from getting into the

room.

NOTE: If the gasket supplied does not fit your

window, obtain appropriate material locally to

provide a proper installation seal.

Wood

Vinyl

5. INSTALL WINDOW LOCKING

BRACKET AND FOAM TOP

WINDOW GASKET (continues)

D. For additional energy savings, on AHD06 only,

measure and cut the adhesive backed foam

sheets, and apply over the side curtains and

frames to seal air leakage.

Side Curtain

Foam

Weather

Seals

49-7778-2 15

Troubleshooting Tips... Before you call for service

Save time and money! Review the charts on the following pages first and you may not need to call for service.

Problem Possible Cause What To Do

Air conditioner does not

start.

The unit is unplugged. Make sure the air conditioner plug is pushed completely

into the outlet.

The fuse is blown/circuit breaker

is tripped.

Check the house fuse/circuit breaker box and replace

the fuse or reset the breaker.

Power Failure. The unit will automatically restart in the setting last

used after the power is restored.

There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start normal

cooling for 3 minutes after it is turned back on.

The current interrupter device is

tripped.

Press RESET button located on the power cord plug.

If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Remote control is not

working

Batteries are dead. Replace the batteries.

Batteries inserted wrong. Make sure batteries are inserted in the correct position.

Air conditioner does not

cool as it should.

Indoor airflow is restricted. Make sure there are not curtains, blinds or furniture

blocking the front of the air conditioner.

The temp control may not be set

properly.

Turn the temperature control to a higher number.

The air filter is dirty. Clean the filter at least every 30 days. See Care and

Cleaning section.

The room may have been hot. When the air conditioner is first turned on, you need to

allow time for the room to cool down.

Cold air is escaping. Check for open furnace registers and cold air returns.

Cooling coils have iced up. See “Air conditioner freezing up” below.

Air conditioner freezing up Ice blocks the air flow and stops

the air conditioner from cooling

the room.

On models with control knobs, set the mode control at

High Fan or High Cool with the Temp at 1 or 2.

Water drips outside Hot, humid weather. This is normal.

Water drips inside The air conditioner is not tilted to

the outside.

For proper disposal, make sure the air conditioner

slants slightly from the case front to the rear.

Water collects in base pan Moisture removed from air and

drain into base pan.

This is normal for a short period in areas with little

humidity; normal for a longer period in very humid

areas.

TROUBLESHOOTING TIPS

16 49-7778-2

TROUBLESHOOTING TIPS

Ŷ<RXPD\KHDUDSLQJLQJQRLVHFDXVHGE\ZDWHUEHLQJSLFNHGXSDQGWKURZQDJDLQVWWKHFRQGHQVHURQUDLQ\GD\V

or when the humidity is high. This design feature helps remove moisture and improve efficiency.

Ŷ<RXPD\KHDUWKHWKHUPRVWDWFOLFNZKHQWKHFRPSUHVVRUF\FOHVRQDQGRII

Ŷ:DWHUZLOOFROOHFWLQWKHEDVHSDQGXULQJKLJKKXPLGLW\RURQUDLQ\GD\V7KHZDWHUPD\RYHUIORZDQGGULSIURPWKH

outdoor sideof the unit.

Ŷ7KHIDQPD\UXQHYHQZKHQWKHFRPSUHVVRUGRHVQRW

Ŷ:DWHUGURSOHWVEHLQJWKURZQDJDLQVWWKHRXWVLGHFRLOVFDQPDNHDSLQJLQJQRLVH7KLVKHOSVFRROWKHFRQGHQVHU

You can reduce this noise by removing the subbase water plug.

To ensure maximum efficiency it is recommended to check to ensure the rubber drain plug is properly inserted.

This plug may be removed during operation to minimize water in the back of the unit; however, removing it will

lower the efficiency of your unit.

NOTE: Do not drill hole in the base pan.

Subbase Water Plug

Normal Operating Sounds

49-7778-2 17

LIMITED WARRANTY

GE Appliances Air Conditioner Limited Warranty

Staple your receipt here.

Proof of the original purchase date is needed to make a warranty claim.

EXCLUSION OF IMPLIED WARRANTIES - Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed by law.

For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for

SURGXFWVSXUFKDVHGIRUKRPHXVHZLWKLQWKH86$,IWKHSURGXFWLVORFDWHGLQDQDUHDZKHUHVHUYLFHE\D*(

Appliances Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to

bring the product to an Authorized GE Appliances Service location for service. In Alaska, the limited warranty excludes

the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor US:

GE Appliances, a Haier company

Ŷ&XVWRPHULQVWUXFWLRQ7KLVRZQHU¶VPDQXDOSURYLGHV

information regarding operating instructions and

user controls.

Ŷ,PSURSHULQVWDOODWLRQ,I\RXKDYHDQLQVWDOODWLRQ

problem, or if the air conditioner is of improper

capacity, contact your dealer or installer. You

are responsible for providing adequate electrical

connecting facilities.

Ŷ)DLOXUHRIWKHSURGXFWUHVXOWLQJIURPPRGLILFDWLRQV

to the product or due to unreasonable use including

failure to provide reasonable and necessary

maintenance.

Ŷ5HSODFHPHQWRIKRXVHIXVHVRUUHVHWWLQJRIFLUFXLW

breakers.

Ŷ)DLOXUHGXHWRFRUURVLRQRQPRGHOVQRWFRUURVLRQ

protected.

Ŷ'DPDJHWRWKHSURGXFWFDXVHGE\LPSURSHUSRZHU

supply voltage, accident, fire, floods or acts of God.

Ŷ,QFLGHQWDORUFRQVHTXHQWLDOGDPDJHFDXVHGE\

possible defects with this air conditioner.

Ŷ'DPDJHFDXVHGDIWHUGHOLYHU\

What Will Not Cover:

For The Period Of: Will Replace:

One Year

From the date of the

original purchase

Replacement, repair, or refund of the original retail price for any product which fails due

to a defect in materials or workmanship. If the unit is exchanged, the replacement unit

is warranted for the remainder of your product’s original one-year warranty period. GE

Appliances will, at its sole discretion, replace the product with a product of the same or

comparable functionality and quality or refund the original retail price.

Ŷ Properly pack your unit. We recommend using the

original carton and packing materials.

Ŷ5HWXUQWKHSURGXFWWRWKHUHWDLOORFDWLRQZKHUHLWZDV

purchased.

Ŷ Include in the package a copy of the sales receipt

or other evidence of date of original purchase. Also

print your name and address and a description of the

defect.

In Order to Make a Warranty Claim During the First 90 Days from the Date of Original Purchase:

Ŷ/RFDWH\RXURULJLQDOVDOHVUHFHLSWDQGPDNHDQRWHRI

your model and serial number.

Ŷ&DOO866-907-1655LQWKH8QLWHG6WDWHV to initiate the

product replacement process.

Ŷ<RXZLOOEHDVNHGWRSURYLGH\RXUQDPHDGGUHVV

date of purchase, model and serial number.

Ŷ*($SSOLDQFHVZLOODUUDQJHIRUDFDUWRQWREHVHQWWR

your home to recover the product.

Ŷ Please return all requested materials (postage pre-paid)

in the carton provided. Please include a description of the

defect.

Ŷ<RXVKRXOGUHFHLYH\RXUUHSODFHPHQWSURGXFWRU

refund within 7 to 10 business days after your

package is received.

In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

18 49-7778-2

Printed in China

Consumer Support

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

VHUYLFHVGHVLJQHGIRU\RXUFRQYHQLHQFH,QWKH86GEAppliances.com

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

WKHSUHSULQWHGUHJLVWUDWLRQFDUGLQFOXGHGLQWKHSDFNLQJPDWHULDO,QWKH86GEAppliances.com/register

Schedule Service

Expert GE Appliances repair service is only one step away from your door. Get on-line and schedule your service at

\RXUFRQYHQLHQFHDQ\GD\RIWKH\HDU,QWKH86GEAppliances.com/service or call 800.432.2737 during normal

business hours.

Extended Warranties

Purchase a GE Appliances extended warranty and learn about special discounts that are available while your

warranty is still in effect. You can purchase it on-line anytime. GE Appliances Services will still be there after your

ZDUUDQW\H[SLUHV,QWKH86GEAppliances.com/extended-warranty or call 800.626.2224 during normal

business hours.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable),visit our website at

GEAppliances.com/connectRUFDOOLQWKH86

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

,QWKH86GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

,QWKH86*HQHUDO0DQDJHU&XVWRPHU5HODWLRQV_*($SSOLDQFHV$SSOLDQFH3DUN_/RXLVYLOOH.<

GEAppliances.com/contact

CONSUMER SUPPORT

ACCONDICIONADORES DE AIRE

PARA SALA

GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.

MANUAL DEL

PROPIETARIO

Escriba los números de modelo y de

serie aquí:

Nº de Modelo ____________

Nº de Serie ______________

Estos números se encuentran en una

etiqueta al costado del acondicionador

de aire.

INFORMACIÓN DE SEGURIDAD ...3

USO DEL ACONDICIONADOR DE

AIRE

Controles .............................4

CUIDADO Y LIMPIEZA .............8

INSTRUCCIONES DE INSTALACIÓN

Antes de comenzar ....................9

Requisitos Eléctricos ..................9

Piezas Incluidas ......................10

Requisitos de la Ventana .............. 11

Preparación del Acondicionador de Aire 11

Instalación del Acondicionador de Aire . 12

CONSEJOS PARA LA SOLUCIÓN

DE PROBLEMAS .................14

Sonidos de Funcionamiento Normal ....15

SOPORTE AL CLIENTE

Garantía Limitada .....................17

Soporte al Cliente ....................18

49-7778-2 09-19 GEA

AHD06

AHD08

2 49-7778-2

GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.

Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace

tenerlo en la familia.

Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de

GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico

asegura que podamos entregarle información importante del producto y detalles de la garantía

cuando los necesite.

Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles

están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.

También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con

el material embalado.

Page is loading ...

GE AHD06LZ Owner's manual

Brand: GE

Model: AHD06LZ

Type: Owner's manual

Download PDF

report

in other languages

español: GE AHD06LZ El manual del propietario

GE AHD06LZ Owner's manual

GE AHD06LZ Owner's manual

in other languages

Related papers

Other documents