Balboa Micro Jet Replacement Nozzle User manual

Balboa
Brand
Balboa
Model
Micro Jet Replacement Nozzle
Type
User manual

Balboa Micro Jet Replacement Nozzle

Below you will find brief product information for Balboa Micro Jet Replacement Nozzle.

The Balboa Micro Jet Replacement Nozzle is a small, easy-to-install replacement nozzle for your Balboa micro jet.

This nozzle is designed to improve the performance of your micro jet, and it can be used to replace a worn or damaged nozzle.

The nozzle is made of durable plastic, and it is easy to clean and maintain.

Here are some of the benefits of using the Balboa Micro Jet Replacement Nozzle:

  • Improved performance: The nozzle is designed to improve the performance of your micro jet, by increasing the water pressure and flow rate.

Balboa Micro Jet Replacement Nozzle

Below you will find brief product information for Balboa Micro Jet Replacement Nozzle.

The Balboa Micro Jet Replacement Nozzle is a small, easy-to-install replacement nozzle for your Balboa micro jet.

This nozzle is designed to improve the performance of your micro jet, and it can be used to replace a worn or damaged nozzle.

The nozzle is made of durable plastic, and it is easy to clean and maintain.

Here are some of the benefits of using the Balboa Micro Jet Replacement Nozzle:

  • Improved performance: The nozzle is designed to improve the performance of your micro jet, by increasing the water pressure and flow rate.
Installation Instructions
Micro Jet Replacement Nozzle
Tools required:
Medium sized flathead screwdriverUÊ
Medium sized needle nose pliersUÊ
STEP 1 – Adjusting Scalloped Flange
Rotate scalloped adjusting flange counterclockwise (looking
into jet) until it stops.
STEP 2 – Removing Scalloped Flange
Remove scalloped adjusting flange from jet retaining
flange by pulling straight out of jet. If it does not easily
release from its snapped-in position, place the flathead
of a screwdriver between the jet flange and the scalloped
adjusting flange and carefully pry it loose.
STEP 3 – Breaking and Removing Old Jet Nozzle
The old jet nozzle will be broken into pieces when
removing. To do this, grip old jet nozzle tightly with needle
nose pliers at points shown, and firmly pull nozzle toward
you. This nozzle will most likely come out in pieces so be
sure to remove all pieces from jet body. Also, be careful not
to damage threads of jet body.
99510500 B January 20, 2010Page 1 of 2
IMPORTANT SAFETY INSTRUCTIONS
READ & FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION
Threads can be damaged when removing old nozzle. If threads are damaged you may not be able to install
the new nozzle and the entire jet may have to be replaced. To avoid this hazard, follow nozzle removal
instructions closely and be sure all broken nozzle pieces are removed from the jet.
Page 2 of 2
STEP 7 – Re-installing Scalloped Adjusting Flange
Re-install scalloped adjusting flange. Be sure that the retaining ring is adjusting as described in Step 6 so that
drive legs of adjusting flange will pass through slots in retaining ring.
STEP 4 – Installing New Nozzle
Hold new nozzle with needle nose pliers by gripping
nozzle on hex pattern (not on orifice) and insert into jet
body. After nozzle is inserted, be sure nozzle is seated
properly and is rotated clockwise (looking into jet) until
it stops. You may need to push nozzle into final position
with your finger. This will help you to “feel” the seated
position of the nozzle.
STEP 5 – Installing Split Retaining Ring
Insert split retaining ring with adjusting boss facing outward by pushing first one end into jet body and then the
other. Be sure retaining ring has snapped into jet body behind jet retaining flange and is laying flat around hex of
nozzle. Thread on retaining ring must engage internal threads of jet body without crossthreading and turn freely.
STEP 6 – Adjusting the Split Retaining Ring
Rotate the split retaining ring in threads of jet body with tip of screwdriver until it touches the nozzle.
Additionally, turn the ring until drive leg slots in the ring expose the next set of openings on nozzle.
This is the proper adjustment for the retaining ring. Do not over tighten as this may cause damage to the jet or
cause the jet to not operate properly.
CAUTION
Do not over tighten split retaining ring. Over tightening the split retaining ring can cause damage to the jet, or cause
the jet to not operate properly. Tighten until alignment is reached and no further.
SAVE THESE INSTRUCTIONS
  • Page 1 1
  • Page 2 2

Balboa Micro Jet Replacement Nozzle User manual

Balboa
Brand
Balboa
Model
Micro Jet Replacement Nozzle
Type
User manual

Balboa Micro Jet Replacement Nozzle

Below you will find brief product information for Balboa Micro Jet Replacement Nozzle.

The Balboa Micro Jet Replacement Nozzle is a small, easy-to-install replacement nozzle for your Balboa micro jet.

This nozzle is designed to improve the performance of your micro jet, and it can be used to replace a worn or damaged nozzle.

The nozzle is made of durable plastic, and it is easy to clean and maintain.

Here are some of the benefits of using the Balboa Micro Jet Replacement Nozzle:

  • Improved performance: The nozzle is designed to improve the performance of your micro jet, by increasing the water pressure and flow rate.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents