Hoshizaki KM-901MAH User manual

KM-901MAH
Hoshizaki
Brand
Hoshizaki
Model
KM-901MAH
Category
Ice cube makers
Type
User manual

This manual is also suitable for

ICE MACHINE
CLEANING & SANITIZING
Ice machine should be cleaned and
sanitized at least once a year.
Item #51010 02.26.18
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Base Cover, disconnect the Pump Tubing. After the water tank has
drained, reconnect Pump Tubing. Do not replace the base cover at this time.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove the
Front Panel, then move the control switch to OFF.
Remove the Front Insulation Panel. Pour 14 fl.oz
(414 ml) of Hoshizaki Scale Away into the water
tank. Replace the Front Insulation Panel. Turn the
cleaning valve left until completely vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait
1 minute before next step.
Move the control switch to WASH, replace Front
Panel.
Ice Machine
KM-340MAH, MWH
KM-515MAH, MWH, MRH
KM-600MAH
KM-650MAH, MWH, MRH
KM-901MAH, MWH, MRH/3
OPEN
3
min.
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour .78 fl. oz (23 ml) of
chlorine bleach* into the
water tank
xReplace the front insulation
panel
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xMove control switch to OFF
xDisconnect the pump tubing
xAfter the water tank has
drained, reconnect the pump
tubing
3
min
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
A
1
A
2
R
3
R
d
4
14
15
16
17
g
18
R
re
5
(4
6
M
P
7
Front View of
Ice Maker
Base
Cover
Page 1
#51001 | 7.22.2016
Page 2
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
NOTICE! DO NOT leave the control switch on WASH
for extended periods when water tank is empty. It will
damage water pump seals.
Remove the Pump Tubing. Clean all items (See
Step 10). Once water tank has drained, replace and
reconnect all the items.
In bad water conditions, a more thorough cleaning may
be required. Turn off power supply, clean all items in a
solution of 5 oz. of Scale Away per gallon of warm
water. Rinse and replace the cube guides, float switch,
water supply tubes, spray tubes and spray guides. Turn
on power supply. Otherwise, continue to Step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Disconnect the Pump Tubing. After the water tank
has drained, reconnect Pump Tubing. Continue to
Sanitation – Step ༛on front...
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
30
min.
!
sanitizing continued…
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xDisconnect the pump
tubing
xAfter the water tank has
drained, reconnect the pump
tubing
RINSE 2 & 3:
(Steps 22-28)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE cleaning valve
xMove control switch to ICE,
replace front panel
xReplace all panels in their
correct positions
CONTROL PANEL
WASH >5 minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
xTo allow cleaning solution flow to
the inside the evaporator
xTurn left to open (vertical)
CLOSE cleaning valve:
xMust be closed for normal ice
making operation
xTurn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
A
8
R
S
9
I
b
10
T
h
11
T
12
19
D
h
13
20
21
22
29
AMMONIA
Cleaners
30
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
#51001 | 7.22.2016
Page 3
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Front Insulation Panel, slide the Cube Guide to right. Remove the
Rubber Cap &Sleeve covering the Overflow Pipe. Unscrew the Overflow Pipe.
Once the water tank has drained, replace all the items.
Refill water tank by moving the control switch to ICE,
replace the Front Panel. After 3.5 minutes, remove
Front Panel, move switch to OFF.
Remove the Front Insulation Panels. Pour 30 fl.oz
(887 ml) of Hoshizaki Scale Away into the water tank.
Replace the Front Insulation Panels. Turn the
cleaning valve left until completely vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait 1 minute
before next step.
Move the control switch to WASH, replace Front Panel.
NOTICE! DO NOT leave the control switch on WASH
for extended periods when water tank is empty. It will
damage water pump seals.
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
Ice Machine
KM-1100MAH, MWH, MRH
KM-1340MAH, MWH, MRH
KM-1601MRH/3
OPEN
Front of
Ice Maker
with
Front
Panel
removed
3.5
min.
30
min.
3
min
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker unattended when
panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
1
A
2
R
3
R
4
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3.5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour 1.7 fl. oz (50 ml) of
chlorine bleach* into the
water tank
xReplace the top, left, and
insulation panels
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xMove control switch to OFF
xRemove the front insulation
panel
xSlide the cube guide to right
xRemove rubber cap & sleeve
covering the overflow pipe
xUnscrew overflow pipe, drain
water tank
xReplace the rubber cap, sleeve,
cube guide & insulation panel
14
n
15
16
17
n
18
R
5
R
6
M
7
#51003 | 7.22.2016
Page 1
Left side of
Ice Maker
View
through side
panel
A
8
Page 4
Remove the Front Insulation Panel, slide the Cube Guide to right. Remove the
Rubber Cap &Sleeve covering the Overflow Pipe. Unscrew the Overflow Pipe.
Clean all items (See Step 10). Once the water tank has drained, replace all the items.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3.5 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel, slide the
Cube Guide to right. Remove the Rubber Cap &
Sleeve covering the Overflow Pipe. Unscrew the
Overflow Pipe. Once the water tank has drained,
replace all the items.
Continue to Sanitation – Step ༛ on front...
CLOSE
CONTROL PANEL
ICE >3.5 minutes >OFF
OPEN
!
sanitizing continued…
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3.5 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xSlide the cube guide to right
xRemove rubber cap & sleeve
covering the overflow pipe
xUnscrew overflow pipe, drain
water tank
xReplace the rubber cap, sleeve,
cube guide & insulation panel
RINSE 2 & 3:
(Steps 22-28)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE the cleaning valve
xMove control switch to ICE
xReplace all panels
CONTROL PANEL
WASH >5minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
x
To allow cleaning solution flow to
the inside the evaporator
x
Turn left to open (vertical)
CLOSE cleaning valve:
xMust be closed for normal ice
making operation
xTurn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
R
9
In
10
T
h
11
19
T
12
R
13
20
n
21
22
30
Page 2
#51003 | 7.22.2016
31
AMMONIA
Cleaners
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
29
Page 5
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Front Insulation Panel, remove the Drain Plug. After the water tank
has drained, replace Drain Plug. Replace the Front Insulation Panel.
NOTICE! DO NOT cross thread the drain plug.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove the
Front Panel, then move the control switch to OFF.
Remove the Front Insulation Panel. Pour Hoshizaki
Scale Away into the water tank (see Table).
Replace the Front Insulation Panel. Turn the cleaning valve left until completely
vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait
1 minute before next step.
Ice Machine
KM-1301SAH/3, SWH/3, SRH/3
KM-1601SAH/3, SWH/3, SRH/3
KM-1900SAH/3, SWH/3, SRH/3
KM-2100SWH3, SRH3
KM-2500SWH3, SRH3
OPEN
3
min.
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour chlorine bleach* into the
water tank (see below)
KM-1601 and smaller
3.75 fl. oz (110 ml)
KM-1900 and larger
5 fl. oz (148 ml)
xReplace the front insulation
panel
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xMove control switch to OFF
3
min
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
1
A
2
R
3
R
h
4
14
n
15
16
17
R
5
R
S
6
Front View of Ice Maker with Front Panel removed
#51002 | 7.21.2016
Page 1
Page 6
Move the control switch to WASH, replace Front Panel.
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
NOTICE! DO NOT leave the control switch on WASH
for extended periods when water tank is empty. It will
damage water pump seals.
Remove the Front Insulation Panel, remove the Drain Plug. Clean all items (See
Step 10). Once water tank has drained, replace all items.
In bad water conditions, a more thorough cleaning may
be required. Turn off power supply, clean all items in a
solution of 5 oz. of Scale Away per gallon of warm
water. Rinse and replace the cube guides, float switch,
water supply tubes, spray tubes and spray guides. Turn
on power supply. Otherwise, continue to Step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel, then remove
the Drain Plug. After the water tank has drained,
replace all items. Continue to Sanitation – Step ༛
on front...
Tech Support: 1.800.233.1940
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
30
min.
#51002 | 7.21.2016
!
sanitizing continued…
xRemove the front
insulation panel and drain
plug
xAfter the water tank has
drained, replace drain plug and
front insulation panel
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front
insulation panel and drain
plug
xAfter the water tank has
drained, replace drain plug and
front insulation panel
RINSE 2 & 3:
(Steps 22-28)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xReplace all panels in their
correct positions
CONTROL PANEL
WASH >5minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
x
To allow cleaning solution flow to
the inside the evaporator
x
Turn left to open (vertical)
CLOSE cleaning valve:
xMust be closed for normal ice
making operation
xTurn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
18
M
7
A
8
R
9
In
10
T
h
11
T
12
R
13
AMMONIA
Cleaners
19
20
21
22
30
29
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
Page 7
Cleaning Prep:
Remove the Front Panel, move the control switch to
OFF.After 3 min., move the control switch to ICE, then
replace the Front Panel
.
After 3 min., remove the Front Panel, move the
control switch to OFF. This removes the cubes from
the evaporator. Replace the Front Panel.
Remove all ice from the dispenser unit/ice storage bin.
ATTENTION! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the ice.
Cleaning:
Remove the Front Panel,movetheservice switch to
DRAIN.Move control switch to SERVICE. Replace the
Front Panel.
After 2 minutes, remove the Front Panel, move the
control switch to OFF.
Dilute Hoshizaki Scale Away with warm water (see Table below).
Remove the Insulation Panel (A) and pour cleaning solution into
the water tank.
KMD-410, 460, 530
Scale Away 9.5 fl. oz (281 ml)
Warm Water 1.8 gal. (6.8 l)
In bad water conditions, a more thorough cleaning may
be required. Move control switch to OFF, then turn off
the power supply. Dilute 5 oz. of Scale Away to 1
gallon of warm water. Remove and clean the float
switch assembly (see Float Switch Cleaning on back),
water supply tubes, spray tubes, water tank, and pump
motor and float switch assembly. Rinse thoroughly,
then replace in their correct positions. Turn the power
supply back on. Otherwise, continue to Step ව.
Ice Machine
KMD-410MAH, MWH, MRH
KMD-460MAH, MWH, MRH
KMD-530MAH, MWH, MRH
Sanitizing:
xDilute 5.25% chlorine
bleach* with warm water
(see Table below)
KMD-410, 460, 530
Bleach 0.9 fl. oz (27 ml)
Warm Water 1.8 gal. (6.8 l)
* Use bleach without additives.
xRemove the front panel &
insulation panel (A)
xPour the sanitizing solution
into the water tank
xReplace all the panels, except
the front panel
xMove service switch to
WASH and control switch to
SERVICE, replace the front
panel
xAfter 15 minutes, remove
front panel
xMove service switch to DRAIN,
replace the front panel
xAfter 2 minutes, remove
front panel
xMove control switch to OFF
3
min.
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The icemaker must be cleaned & sanitized at least once a year.
ATTENTION!
Do not leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
1
A
c
2
R
3
R
4
15
16
17
18
19
A
5
D
R
6
After 2 min.
I
7
Top
T
Top
Service Switch
Control Switch
Water Tank
Right
Side
Front of icemaker
Insulation Panel (B)
Thumbscrews
Tech Support: 1.800.233.1940
Page 1
#51009 | 4.28.2017
Page 8
KMD-460 & 530M_H:
Loosen the two thumbscrews on the pump insulation
panel (B) and remove the panel.
Disconnect the discharge hose, the drain valve hose,
and the overflow drain hose.
Disconnect the pump motor and then the float switch
connectors from the control board.
Remove the two thumbscrews securing the pump
motor and float switch assembly.
Pull out the water tank, cube guide, and pump motor
and float switch assembly all together.
Remove the screw securing the float switch to the
top of the assembly, remove the float switch*.
See Step ඿for cleaning steps. Reassemble in the
reverse order they were removed.
* Remove retainer rod (take care not to bend excessively) from bottom of the float switch housing & clean all float parts.
Replace all the Panels, except the Front Panel.
Move the service switch to WASH, and the control
switch to SERVICE. Replace the Front Panel.
After 30 minutes, remove the Front Panel, move
the service switch to DRAIN. Replace the Front
Panel.
ATTENTION! To prevent damage to the water pump,
do not leave the control switch on SERVICE for
extended periods when water tank is empty.
Cleaning Rinse:
After 2 minutes, remove the Front Panel, move the control switch to ICE. Replace
the Front Panel.
After 3 minutes, move the service switch to WASH,and the control switch to
SERVICE. Replace the Front Panel.
After 5 minutes, remove the Front Panel, move the service switch to DRAIN.
Replace the Front Panel
After 2 minutes, remove the Front Panel, move the control switch to OFF.
Repeat 3x (Steps ༗thru ༚)to rinse thoroughly. Continue to Sanitation – Step ༜
on front...
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIcemaker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
Tech Support: 1.800.233.1940
Page 2
#51009 | 4.28.2017
!
sanitizing continued…
RINSE 1:
(Steps 20-22)
xMove control switch to ICE,
replace front panel
xAfter 3 minutes, remove the
front panel
xMove service switch to WASH
and control switch to SERVICE,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove service switch to DRAIN,
replace the front panel
xAfter 2 minutes, remove
the front panel
xMove control switch to OFF,
replace the front panel
RINSE 2:
xRepeat RINSE 1 (Steps 20–22)
for complete ice/food safety
xClean the dispenser unit /
ice storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xMove control switch to ICE,
replace front panel
R
M
8
A
9
A
10
A
11
A
12
AMMONIA
Cleaners
20
e
21
22
23
,
25
24
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
After
30 min.
A
13
R
14
After
2 min.
After
3 min.
DO NOT use ammonia type cleaners
WEAR liquid-proof gloves and goggles
to protect skin & eyes from cleaning &
sanitizing chemicals
DO
N
OT
us
e
am
mo
ni
a
ty
pe
c
le
an
er
s
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
KMD-410M_H:
Loosen the two thumbscrews securing the
pump motor bracket.
Disconnect the discharge hose.
Disconnect the pump motor and float switch
connectors from the side of the control box.
While pushing up on the snap tab, pull out the
water tank, cube guide, pump motor bracket,
and pump motor and float switch assembly all
together.
Remove the pump motor bracket securing the
float switch to the top of the assembly, remove
the float switch*.
See Step ඿for cleaning steps. Reassemble in
the reverse order the
y
were removed.
co
Re
m
Pu
an
Re
t
o
Se
re
FLOAT SWITCH CLEANING
After
5 min.
After
3 min. Repeat
3x
Page 9
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Front Insulation Panel, Cube Guide B & A, Overflow Cap & Pipe,
Water Shield, and Drain Plug. After the water tank has drained, replace all items.
NOTICE! DO NOT cross thread the drain plug or
overflow pipe.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove Front
Panel, move switch to the OFF position.
Remove the Front Insulation Panels. Pour 14 fl.oz
(414 ml) of Hoshizaki Scale Away into the water
tank. Replace the front insulation panel. Turn the
cleaning valve left until completely vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait 1
minute before next step.
Move the control switch to WASH, replace Front Panel.
NOTICE! DO NOT leave the control switch on WASH for extended periods when
water tank is empty. It will damage water pump seals.
Ice Machine
KMD-850MAH, MWH, MRH
KMD-901MAH, MWH, MRH
OPEN
3
min.
3
min
3
min.
Cleaning & Sanitizing
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
A
1
A
2
R
3
R
4
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour .78 fl. oz (23 ml) of
chlorine bleach* into the
water tank
xReplace the front insulation
panel
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xRemove the front panel
xMove the control switch to OFF
xRemove the front insulation
panel, cube guide B & A,
overflow cap & pipe, water
shield, and drain plug
xAfter the water tank has
drained, replace all items
14
n
15
16
17
R
5
R
(
6
M
7
Front View of Ice Maker
#51004 | 7.22.2016
AMMONIA
Cleaners
n
18
Page 10
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
Remove the Front Insulation Panel, Cube Guide B
& A, Overflow Cap & Pipe, Water Shield, and Drain
Plug. Clean all items (See Step 10). After the water
tank has drained, replace all items.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel, Cube Guide
B & A, Overflow Cap & Pipe, Water Shield, and
Drain Plug. After the water tank has drained,
replace all items.
Continue to Sanitation – Step ༛on front...
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
30
min.
!
sanitizing continued…
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel, cube guide B & A,
overflow cap & pipe, water
shield, and drain plug
xAfter the water tank has
drained, replace all items
RINSE 2 & 3:
(Steps 22-27)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE the cleaning valve
xMove control switch to ICE
xReplace all panels
CONTROL PANEL
WASH >5 minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
xTo allow cleaning solution flow to
the inside the evaporator
xTurn left to open (vertical)
CLOSE cleaning valve:
x
Must be closed for normal ice
making operation
x
Turn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
A
8
R
9
In
10
T
h
11
T
v
12
19
R
B
13
2
20
n
21
22
28
29
AMMONIA
Cleaners
#51004 | 7.22.2016
30
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
Page 11
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Front Insulation Panel. Remove the Drain
Plug. Once the water tank has drained, replace the
Drain Plug and Insulation Panel.
NOTICE! DO NOT cross thread the drain plug.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove Front
Panel, move switch to the OFF position.
Remove the Front Insulation Panels. Pour 43 fl.oz
(1,272 ml) of Hoshizaki Scale Away into the water
tank. Replace the front insulation panel. Turn the
cleaning valve left until completely vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait
1 minute before next step.
Move the control switch to WASH, replace Front
Panel.
NOTICE! DO NOT leave the control switch on WASH
for extended periods when water tank is empty. It will
damage water pump seals.
Ice Machine
KMH-2000SWH/3
KMH-2000SRH/3
OPEN
Front
View of
Ice Maker
3
min.
30
min.
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour 5 fl. oz (148 ml) of
chlorine bleach* into the
water tank
xReplace the front insulation
panel
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xMove control switch to OFF
xRemove the front
insulation panel
xRemove drain plug
xAfter the water tank has
drained, replace drain plug and
insulation panel
3
min
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker
unattended when
p
anels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
A
1
A
2
R
3
R
4
14
n
15
16
17
R
5
R
(
1
6
M
P
7
#51005 | 7.22.2016
Page 12
After 30 minutes, remove Front Panel, then move the control switch to OFF.
Remove the Front Insulation Panels. Remove the Drain Plug. Clean all items (See
Step 10). Once the water tank has drained, replace the Drain Plug and Insulation
Panel.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel. Remove the
Drain Plug. Once the water tank has drained,
replace the Drain Plug and Insulation Panel.
Continue to Sanitation – Step ༛on front...
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
!
sanitizing continued…
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front
insulation panel
xRemove drain plug
xAfter the water tank has
drained, replace and reconnect
all the items
RINSE 2 & 3:
(Steps 22-27)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE the cleaning valve
xMove control switch to ICE
xReplace all panels
CONTROL PANEL
WASH >5 minutes >OFF
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
xTo allow cleaning solution flow to
the inside the evaporator
xTurn left to open (vertical)
CLOSE cleaning valve:
x
Must be closed for normal ice
making operation
x
Turn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
A
8
R
S
9
I
n
10
T
h
11
T
v
12
19
R
D
13
20
21
22
28
29
30
AMMONIA
Cleaners
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
#51005 | 7.22.2016
Page 13
CONTROL SWITCH
SERVICE SWITCH
Front of Icemaker
(KML-351MAH shown)
Side
Top
Cleaning Prep:
Remove the Front Panel, move the control switch to
OFF.After 3 min., move the control switch to ICE, then
replace the Front Panel
.
After 3 min., remove the Front Panel, move the
control switch to OFF. This removes the cubes from
the evaporator.
Remove all ice from the dispenser unit/ice storage bin.
ATTENTION! IF ON DISPENSER, turn off the dispenser
power supply after dispensing all the ice.
Cleaning:
Remove the Front Panel,movetheservice switch to
DRAIN.Move control switch to SERVICE. Replace
the Front Panel.
After 2 minutes, remove the Front Panel, move the
control switch to OFF.
Dilute Hoshizaki Scale Away with warm water (see Table below).
Remove the Front Insulation Panel and pour cleaning solution
into the water tank. Replace the Front Insulation Panel.
Ice Machine
KML-250MAH, MWH
KML-351MAH, MWH
KML-451MAH, MWH
KML-631MAH, MWH, MRH
Sanitizing:
x Dilute 5.25% chlorine
bleach* with warm water
(see Table below)
KML-451 and smaller
Bleach 1 fl. oz (30 ml)
Warm Water 2 gal. (7.6 l)
KML-631
Bleach 1.25 fl. oz (37 ml)
Warm Water 2.5 gal. (9.5 l)
* Use bleach without additives.
x Remove the front insulation
panel
xPour the sanitizing solution
into the water tank
xReplace the front insulation
panel
x Move service switch to
WASH and control switch to
SERVICE, replace the front
panel
x After 15 minutes, remove
front panel
x Move service switch to DRAIN,
replace the front panel
x After 2 minutes, remove
front panel
x Move control switch to OFF
3
min.
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The icemaker must be cleaned & sanitized at least once a year.
ATTENTION!
Do not leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
1
A
2
R
3
R
4
15
n
16
17
18
A
5
D
R
6
#51007 | 9.16.2016
After 2 min.
Page 14
Move the service switch to WASH, and the control
switch to SERVICE. Replace the Front Panel.
After 30 minutes, remove the Front Panel, move the
service switch to DRAIN. Replace the Front Panel.
ATTENTION! To prevent damage to the water
pump, do not leave the control switch on SERVICE
for extended periods when water tank is empty.
In bad water conditions, a more thorough cleaning may
be required. Move control switch to OFF, then turn off
the power supply. Dilute 5 oz. of Scale Away to 1
gallon of warm water. Remove and clean the cube
guides, float switch assembly (remove & clean all float
parts), water supply tubes, spray tubes, and spray
guides. Rinse thoroughly, then replace in their correct
positions. Turn the power supply back on. Otherwise,
continue to Step ༗.
Cleaning Rinse:
After 2 minutes, remove the Front Panel, move the
control switch to ICE. Replace the Front Panel.
After 3 minutes, move the service switch to WASH,and
the control switch to SERVICE. Replace the Front Panel.
After 5 minutes, remove the Front Panel, move the
service switch to DRAIN. Replace the Front Panel
After 2 minutes, remove the Front Panel, move the control
switch to OFF.
Repeat 3x (Steps ༗thru ༚)to rinse thoroughly.
Continue to Sanitation – Step ༜on front...
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIcemaker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
Tech Support: 1.800.233.1940
#51007 | 9.16.2016
!
sanitizing continued…
RINSE 1:
(Steps 19-22)
x Move control switch to ICE,
replace front panel
x After 3 minutes, remove the
front panel
x Move service switch to WASH
and control switch to SERVICE,
replace the front panel
x After 5 minutes, remove the
front panel
x Move service switch to DRAIN,
replace the front panel
x After 2 minutes, remove
the front panel
x Move control switch to OFF,
replace the front panel
RINSE 2:
x Repeat RINSE 1 (Steps 19–22)
for complete ice/food safety
x Clean the dispenser unit /
ice storage bin liner with a
neutral cleaner (dish soap)
x Rinse thoroughly
x Move control switch to ICE,
replace front panel
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/manuals
Type in the model number of your
icemaker (including dashes) to
download manuals
ATTENTION!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
19
7
A
8
In
b
9
A
10
A
11
A
12
AMMONIA
Cleaners
e
20
e
21
22
23
, 25
24
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
M
7
After
30 min.
A
13
R
14
After
2 min.
After 3 min.
After 5 min.
After 2 min.
Repeat 3x
ATTENTION!
IF ICEMAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
Page 15
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Front Insulation Panel, Cube Guide B & A, Overflow Cap & Pipe,
Water Shield, and Drain Plug. After the water tank has drained, replace all items.
NOTICE! DO NOT cross thread the drain plug or
overflow pipe.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove Front
Panel, move switch to the OFF position.
Remove the Front Insulation Panels. Pour 14 fl.oz
(414 ml) of Hoshizaki Scale Away into the water
tank. Replace the front insulation panel. Turn the
cleaning valve left until completely vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait
1 minute before next step.
Move the control switch to WASH, replace Front Panel.
NOTICE! DO NOT leave the control switch on WASH for extended periods when
water tank is empty. It will damage water pump seals.
Ice Machine
KMS-822MLH
OPEN
3
min.
3
min
3
min.
Cleaning & Sanitizing
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
A
1
A
2
R
3
R
4
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel
xPour .78 fl. oz (23 ml) of
chlorine bleach* into the
water tank
xReplace the front insulation
panel
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xRemove the front panel
xMove the control switch to OFF
xRemove the front insulation
panel, cube guide B & A,
overflow cap & pipe, water
shield, and drain plug
xAfter the water tank has
drained, replace all items
14
n
15
16
17
R
5
R
(
6
M
7
Front View of Ice Maker
#51006 | 7.22.2016
AMMONIA
Cleaners
n
18
Page 16
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
Remove the Front Insulation Panel, Cube Guide B
& A, Overflow Cap & Pipe, Water Shield, and Drain
Plug. Clean all items (See Step 10). After the water
tank has drained, replace all items.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ༘.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Front Insulation Panel, Cube Guide
B & A, Overflow Cap & Pipe, Water Shield, and
Drain Plug. After the water tank has drained,
replace all items.
Continue to Sanitation – Step ༛on front...
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
30
min.
!
sanitizing continued…
RINSE 1:
(Steps 19-21)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the front insulation
panel, cube guide B & A,
overflow cap & pipe, water
shield, and drain plug
xAfter the water tank has
drained, replace all items
RINSE 2 & 3:
(Steps 22-27)
xRepeat 2x (Steps 19–21) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE the cleaning valve
xMove control switch to ICE
xReplace all panels
CONTROL PANEL
WASH >5 minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
xTo allow cleaning solution flow to
the inside the evaporator
xTurn left to open (vertical)
CLOSE cleaning valve:
x
Must be closed for normal ice
making operation
x
Turn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
Tech Support: 1.800.233.1940
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
A
8
R
9
In
10
T
h
11
T
v
12
19
R
B
13
2
20
n
21
22
28
29
AMMONIA
Cleaners
#51006 | 7.22.2016
30
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
Page 17
Cleaning Prep:
Remove the Front Panel, move the control switch to OFF.
After 3 min., move the switch to ICE, then replace the panel
.
After 3 min., remove the Front Panel, move the switch to OFF.
Remove all ice from the ice storage bin and/or dispenser.
WARNING! IF ON DISPENSER, turn off the dispenser power
supply after dispensing all the leftover ice.
Cleaning:
Remove the Top,Left, and Insulation Panels. Remove the Distributor Hose.
Remove the Thumbscrew securing Cube Guide B, then remove both Cube
Guides B & A.
Remove the Overflow Cap,Overflow Pipe, and Drain Plug. Once water tank has
drained, replace and reconnect all the items and panels.
NOTICE! DO NOT cross thread the drain plug or
overflow pipe.
Refill water tank by moving the control switch to ICE,
replace the Front Panel.After 3 minutes, remove Front
Panel, move switch to the OFF position.
Remove the Top,Left, and Insulation Panels. Pour
14 fl.oz (414 ml) of Hoshizaki Scale Away into the
water tank. Replace the insulation, left and top
panels. Turn the cleaning valve left until completely
vertical (open).
NOTICE! AVOID EXCESSIVE FOAMING, wait 1 minute before next step.
Tech Support: 1.800.233.1940
Ice Machine
KMS-830MLH
OPEN
Left Side
View of
Ice Maker
3
min.
Sanitizing:
xFill the water tank
xCLOSE the cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xRemove the top, left, and
insulation panels
xPour .78 fl. oz (23 ml) of
chlorine bleach* into the
water tank
xReplace the top, left, and
insulation panels
xOPEN the cleaning valve
* Use bleach without additives.
Additives cause excessive foaming, and
reduces effectiveness of the cleaning.
xWait 1 minute to avoid
excessive foaming
xMove control switch to WASH,
replace the front panel
xAfter 45 minutes, remove
the front panel
xMove control switch to OFF
xRemove the top, left, and
insulation panels
xRemove distribution hose
xRemove thumbscrew from cube
guide B
xRemove cube guide B & A
xRemove the overflow cap,
overflow pipe, and drain plug
xAfter the water tank has
drained, replace and reconnect
all the items
3
min
3
min.
Page 1
#51000 | 7.21.2016
Cleaning & Sanitizing
AMMONIA
Cleaners
The ice maker must be cleaned & sanitized at least once a year.
WARNING!
DO NOT leave icemaker unattended when
panels are off
1continued on the back…
R
A
1
A
2
R
3
R
R
4
17
18
19
21
R
d
5
R
r
e
6
R
1
7
22
20
Page 18
Move the control switch to WASH, replace Front
Panel.
NOTICE! DO NOT leave the control switch on WASH
for extended periods when water tank is empty. It will
damage water pump seals.
After 30 minutes, remove Front Panel, then move the
control switch to OFF.
Remove the Top,Left, and Insulation Panels. Remove the Distributor Hose.
Remove the Thumbscrew securing Cube Guide B, then remove both Cube Guides
B & A.
Remove the Overflow Cap,Overflow Pipe, and Drain Plug. Clean all items (See
Step 12). Once water tank has drained, replace and reconnect all the items.
In bad water conditions, a more thorough cleaning
may be required. Turn off power supply, clean all items
in a solution of 5 oz. of Scale Away per gallon of
warm water. Rinse and replace the cube guides, float
switch, water supply tubes, spray tubes and spray
guides. Turn on power supply. Otherwise, continue to
step ༚.
Cleaning Rinse:
Turn the cleaning valve to the right until completely
horizontal (closed). Move the control switch to ICE,
replace Front Panel.After 3 minutes, remove the
Front Panel, move switch to OFF.
NOTICE! ICE MACHINE WILL NOT WORK,
unless valve is completely closed.
Turn the cleaning valve to the left until completely
vertical (open). Move the control switch to WASH,
replace the Front Panel. After 5 minutes, remove
the Front Panel, switch to OFF.
Remove the Top,Left, and Insulation Panels.
Remove the Distributor Hose. Remove the
thumbscrew securing Cube Guide B, then
remove both Cube Guides B & A.
Remove the Overflow Cap,Overflow Pipe, and Drain Plug. Once water tank has
drained, replace and reconnect all the items. Continue to Sanitation – Step ༞on
front...
Tech Support: 1.800.233.1940
CLOSE
CONTROL PANEL
ICE >3 minutes >OFF
OPEN
30
min.
#51000 | 7.21.2016
!
sanitizing continued…
RINSE 1:
(Steps 23-26)
xCLOSE cleaning valve
xMove control switch to ICE,
replace the front panel
xAfter 3 minutes, remove the
front panel
xMove control switch to OFF
xOPEN cleaning valve
xMove control switch to WASH,
replace the front panel
xAfter 5 minutes, remove the
front panel
xMove control switch to OFF
xRemove the top, left, and
insulation panels
xRemove distribution hose
xRemove thumbscrew from cube
guide B
xRemove cube guide B & A
xRemove the overflow cap,
overflow pipe, and drain plug
xAfter the water tank has
drained, replace and reconnect
all the items
.
RINSE 2 & 3:
(Steps 27-34)
xRepeat 2x (Steps 23–26) for
complete ice/food safety
xClean the dispenser /
storage bin liner with a
neutral cleaner (dish soap)
xRinse thoroughly
xCLOSE the cleaning valve
xMove control switch to ICE
xReplace all panels
CONTROL PANEL
WASH >5 minutes >OFF
DOWNLOAD COMPLETE
INSTRUCTION MANUAL:
hoshizakiamerica.com/support
Type in the model number of your
ice machine (including dashes) to
download manuals
OPEN cleaning valve:
xTo allow cleaning solution flow to
the inside the evaporator
xTurn left to open (vertical)
CLOSE cleaning valve:
x
Must be closed for normal ice
making operation
x
Turn right to close (horizontal)
NOTICE!
IF ICE MAKER IS ON DISPENSER,
remember to turn on the dispenser
after cleaning
WARNING!
DO NOT use
ammonia type
cleaners. Can cause
damage to icemaker
WEAR liquid-proof
gloves and goggles to
protect skin & eyes
from cleaning &
sanitizing chemicals
භ Scoop
භWater Filters
භ Exterior
භBin Door/Top Kit
භIce Maker/Bin
භWater Supply Inlet
භCondenser
භWater Hoses
Dish soap, rinse well
Check psi, change if req’d
Dish soap & damp cloth
Warm water & clean cloth
Follow these instructions
Clean inlet screen
Inspect. Clean with brush
Inspect. Replace if req’d
භ භභ
M
P
8
A
c
9
R
R
10
R
S
11
I
12
T
13
2
23
T
14
2
R
R
15
2
R
16
24
25
26
27
35
36
37
AMMONIA
Cleaners
Need Service or Re
p
air? Locate
y
our closest Hoshizaki Certified Service Tech: hoshizakiamerica.com/locate-service-re
p
Page 19
Cleaning Prep:
Remove the Front Panel, move the control switch to
OFF.After 3 min., move the control switch to ICE, then
replace the Front Panel
.
After 3 min., remove the Front Panel, move the
control switch to OFF. This removes the cubes from
the evaporator.
Remove all ice from the dispenser unit/ice storage bin.
ATTENTION! IF ON DISPENSER, turn off the dispenser
power supply after dispensing all the ice.
Cleaning:

Remove the Front Panel,movetheservice switch to
DRAIN.Move control switch to SERVICE. Replace
the Front Panel.
After 2 minutes, remove the Front Panel, move the
control switch to OFF.
Dilute Hoshizaki Scale Away with warm water (see Table below).
Remove the Front, Apron, Top, Left, & Left Insulation Panels
and pour cleaning solution into the water tank.
KMS-1122MLH(3)
Scale Away 27 fl. oz (800 ml)
Warm Water 5 gal. (19 l)
Ice Machine
<D^ͲϭϭϮϮD>,;ϯͿ
Sanitizing:
x Dilute 5.25% chlorine
bleach* with warm water
(see Table below)
KMS-1122MLH(3)
Bleach 2.5 fl. oz (74 ml)
Warm Water 5 gal. (19 l)
* Use bleach without additives.
x Remove the front, apron,
top, left, & left insulation
panels
xPour the sanitizing solution
into the water tank
x Replace all the panels, except
the front panel
x Move service switch to
WASH and control switch to
SERVICE, replace the front
panel
x After 15 minutes, remove
front panel
x Move service switch to DRAIN,
replace the front panel
x After 2 minutes, remove
front panel
x Move control switch to OFF
3
min.
3
min.
Cleaning & Sanitizing
AMMONIA
Cleaners
The icemaker must be cleaned & sanitized at least once a year.
ATTENTION!
Do not leave icemaker
unattended when panels are off
1continued on the back…
Tech Support: 1.800.233.1940
R
ϭ
A
Ϯ
R
ϯ
R
ϰ
ϭϱ
ϭϲ
ϭϳ
ϭϴ
ϭϵ
A
ϱ
D
R
ϲ
#51008 | 9.15.2016
Page 1
After 2 min.
ƌĂŝŶWůƵŐ
^ĞƌǀŝĐĞ^ǁŝƚĐŚ
ŽŶƚƌŽů^ǁŝƚĐŚ
tĂƚĞƌdĂŶŬ
dŽƉ
>ĞĨƚ
^ŝĚĞ
&ƌŽŶƚŽĨŝĐĞŵĂŬĞƌ
Page 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Hoshizaki KM-901MAH User manual

KM-901MAH
Hoshizaki
Brand
Hoshizaki
Model
KM-901MAH
Category
Ice cube makers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents