KOV SBT300 User manual

Brand: KOV

Model: SBT300

Category: Mobile headsets

Type: User manual

K V

Wireless Entertainment

Bluetooth headset User Guide

SBT300

Thank you for choosing the KOV wireless charging TWS earbud

SBT300, it allows you the freedom to make any calls and enjoy the

music streaming any time. Please read this user manual carefully

also read

your device’s user manual

attention to those important

before using the earbud, and

regarding the Bluetooth function, and pay

safety and maintenance information.

1. Specifications

Bluetooth Specification

Bluetooth Profiles Supported

Battery Capacity

Charging Voltage

Charging Time*

Music Playing Time*

Weight

V4.2

Headset , Handsfree , A2DP,AVRCP

60-65mAh(earpiece)

2800-3000mAh(Power base)

DC3.3-4.2V(earpiece)

DC5V/2.4A

About 2 hours

Up to 5 hours

Up to 200 hours

22x16.8x12mm(earpiece)

95.2*52.6*29.2mm(Power base)

5g/earpiece

Standby Time*

Dimensions

*May vary due to user’s operation mode and device settings.

Talking Time*

213456

MULTI-FUNCTION KEY(MFB)

IRELESS CHARGING LED

N/OUT PORT

2 . Function key

ARPIECE LED

MICROPHONE

SPEAKER

OWER BANK LED

3 . Basic Operations

Charging Your SBT300

Prior to using for the first time, the batteries need to be fully charged

to prolong the battery life.

Put the earpieces into the charging sank and plug the battery base to

a power source, the led will turn on and, if earpiece fully being

charged, the led will turn off, if battery base is fully charged, the 4

leds will be stable.

Turning on the earpiece

In OFF MODE, press and hold MFB for about 3 seconds until you

hear a short beep and voice prompt “power on”, and the led flashes

white, then it will enter into STANDBY MODE.

Turning off the Headset

In ON MODE, press and hold MFB for about 5 seconds until you hear

a short beep and voice prompt “power off”, the led flashes red, then it

will enter into OFF MODE.

Pairing Your earpieces with a Bluetooth Mobile Phone

1. Ensure both earpieces are off, and the distance to your phone is

within 1 meter.

2. Press and hold MFB for about 5 seconds until the led flashes white

and red alternately and voice prompt “pairing” as PAIRING MODE,

the left and right will be connected automatically with voice prompt ,

after both earpieces being paired, the left earpiece will enter into

PAIRING MODE again, its led flashes fast with voice prompt “Pairing”,

now the TWS earbud readies to connect with your cell phone.

3. Activate the Bluetooth function on the phone; search Bluetooth

devices (See the user guide of your phone for instructions).

4. Select “SBT300” from the found devices list of the phone.

5. Enter the passkey “0000” if requested; confirm to pair the earbud with

your phone. If successfully paired, the earbud will beep with voice

prompt “connected”, The earbud enters into the STANDBY MODE,

the led circles white.

(If the pairing cannot be completed within 3 minutes after the PAIRING

MODE has been activated, the earbud will enter into the STANDBY

MODE. Repeat above steps to pair again).

6. Ensure the distance between your earbud and phone is within 10

meters, and without any obstacles. You can use the earbud freely.

7. If the earbud had paired with your phone but disconnected, it will

paired automatically again when turns on within operation range.

Note: Not all cell phones support this function, some may request

reconnection manually.

Multi-points connection (only one earpiece being used supports

this function)

Follow the above pairing procedure to pair with the first phone, power

off after successful pairing, repeat pairing procedure to pair the

second phone, then power off the earbud. Power on the earbud into

standby mode, it will automatically recognize and connect to both

phones

Answering/Ending a Call

Press left MFB once or from your cell phone

Rejecting a Call

Press and hold left MFB for 2 seconds or from your cell phone

Voice Dialing

In STANDBY MODE, press and hold left MFB and say the voice tag

as soon as you hear prompt (ensure your phone supports voice

dialing function, and you have recorded the voice tag into your phone.

See the user guide of your phone for instructions).

Last Number Redialing

Double Press the left MFB under standby mode or from your cell phone

Adjusting Volume

Please adjust volume from your cell phone

Play/Pause

Press any MFB once for music playing or pause, or control from your

cell phone’s APP.

Next/Previous song

Please control from your cell phone’s APP.

Disconnecting

To disconnect the paired earbud from your phone, please turn off the

headset or disconnect the headset from the Bluetooth menu of your

phone.

Note

Due to the power consumption difference, when the Left earbud

power drains, the right one may remain power, it is normal. You now

can pair the right one to your phone for music playing and phone talk.

Power bank operation

Charge your power bank

Connect your battery base to a power source to charge your power

bank.

Charge your digital device

Use offered cable and adapter to charge you devices.

Additional Statements

SBT300 is compliant with the specified Bluetooth version. It does not

guarantee compatibility of all functions on every Bluetooth enabled

device. Please check your device’s user manual for compatibility and

functionality.

The above operations may vary due to different devices.

Manufacturer reserves the right to final explanation of all the above

statements

The surrounding affects much to the wireless connection, if

the connection becomes weak in some specific surroundings,

it does not mean the earbud has quality issues.

KOV SBT300 User manual

Brand: KOV

Model: SBT300

Category: Mobile headsets

Type: User manual

Download PDF

report

KOV SBT300 User manual

KOV SBT300 User manual

Other documents