Shenzhen Concox Information Technology GT03B User manual

Brand
Shenzhen Concox Information Technology
Model
GT03B
Type
User manual

This manual is also suitable for

Importer:
Przedsiębiorstwo Handlowo Usługowe FENIKS
Cyprian Pawlaczyk
ul. Słoneczna 110,
Nowa Kuźnica, 42-350 Koziegłowy
Polska - Poland
NIP: 627
-
114
-
97
-
86
REGON: 240243739
,
[email protected]
USER MANUAL
NAME:
GPS PORTABLE TRACKER
GPS + GSM + SMS / GPRS
MODEL:
GT03B
PLEASE READ THE INSTRUCTIONS
BEFORE USING THE UNIT.
SAVE IT FOR USE IN THE FUTURE.
Strona 2 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
Safety Warning & Attentions .................................................................................................................................................... 3
1.
Attention ...................................................................................................................................................................... 3
2.
Attention for operation of this product ........................................................................................................................ 3
3.
Operation and maintenance ........................................................................................................................................ 3
Product Overview - Model: GT03B ............................................................................................................................................ 3
1.
Accessories: .................................................................................................................................................................. 3
2.
Appearance: ................................................................................................................................................................. 4
3.
Usage: .......................................................................................................................................................................... 4
4.
Performance parameters: ............................................................................................................................................ 4
5.
LED Indicators Status: .................................................................................................................................................. 5
Getting Start .............................................................................................................................................................................. 5
1.
Install the SIM card ...................................................................................................................................................... 5
2.
Power on ...................................................................................................................................................................... 5
3.
Charging battery .......................................................................................................................................................... 5
Device functions and Parameter setting ................................................................................................................................... 6
1.
Settings of APN ............................................................................................................................................................ 6
2.
SOS numbers setting .................................................................................................................................................... 6
3.
Delete SOS numbers ..................................................................................................................................................... 6
4.
Arm /Disarm ................................................................................................................................................................. 6
5.
Vibration alarm ............................................................................................................................................................ 7
6.
SOS alarm ..................................................................................................................................................................... 7
7.
Geo-fence ..................................................................................................................................................................... 7
8.
Low battery alarm ........................................................................................................................................................ 8
9.
Voice monitoring .......................................................................................................................................................... 8
10.
View location method .............................................................................................................................................. 8
11.
Factory recovery settings ......................................................................................................................................... 9
12.
Reboot device .......................................................................................................................................................... 9
Troubleshooting ........................................................................................................................................................................ 9
Warranty instructions and service .......................................................................................................................................... 10
Statement ................................................................................................................................................................................ 10
Strona 3 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
Introduction
Thank you for choosing this GPS Portable Tracker. Please read this Manual carefully to fully understand its usage, perfect
functions and simple operation. The Company reserves the right to modify this Manual from time to time without prior
notice. Before using this product, please read these Attentions carefully to ensure safe and proper operation of this
product.
Safety Warning & Attentions
1. Attention
• Do not place this product on an uneven or unstable table-board to prevent failure or damage caused by falling.
• Only the battery designated by the Company can be used on this product. Application of other products may lead to
leakage, overheating, blowout and fire of the battery.
• Do not crash, vibrate, or throw device in order to avoid failure and fire.
• Do not use this product in a place with flammable and explosive gas; otherwise, product failure and fire may be
caused.
• Do not place this product in a place with high temperature, high humidity or large amount of dust; otherwise,
product failure may be caused.
2. Attention for operation of this product
• Do not dismantle or remodel this product, otherwise, damage, creepage and electrical fault may be caused to this
product.
• Place tiny metal objects such as drawing pin at a place far away from the speaker. As the speaker has magnetic
property while working, it will attract these tiny metal objects, which may lead to personal injuries or damage of the
speaker.
3. Operation and maintenance
• Please keep this product dry, as rainwater, moisture, humidity and liquids or moisture content may contain mineral
matters that erode the circuit.
• Do not keep this product in any place with high temperature. As high temperature may shorten the lifespan
of electronic device, damage the battery and cause deformation or melting of certain plastic parts and components.
• Do not keep this product in any place with low temperature. As when being moved from a place with low
temperature to a place with normal temperature, it may generate humidity inside, which may cause damage of circuit
board.
• Do not attempt to dismantle this product. As improper handling by nonprofessional personnel may cause damage of
the device.
• Do not toss, knock or shake this product, as tough operation mode may damage the motherboard inside the device.
• If this product is made wet by mistake, shut it down, remove the battery, and restart the product after confirming
it complete dry after 24 hours.
• Use clean and dry soft cloth to clean the lens, infrared lamp and light sensor.
Warning: improper operation will void warranty!
Product Overview - Model: GT03B
1. Accessories:
Device
Power cord
Charger
User Manual
Battery
Please make sure that all accessories are complete. Pictures are for indication and illustration purposes only.
GPS
Portable
tracke
r
Strona 4 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
2. Appearance:
3. Usage:
• for person
• for bikes
• for cars
• for vans
• for trucks
• for camper
• for buses
• for motorcycle
• for other vehicles
4. Performance parameters:
Serial Specifications Technical parameters
1 Dimension 76 (L) x 45 (W) x 16 (H) mm
2 Weight 70 g
3 Backup Battery 1000 mAh / 3.7V
4 Operation Temperature -25
℃
-60
℃
5 Humidity 5% - 95%
6 Standby Time 160 hours
7 GSM Frequencies 850/900/1800/1900 MHz
8 GPRS Class 12
9 GPS Channel 20
10 GPS Sensitivity -159dBm
11 Acquisition Sensitivity -144dBm
12 Position Accuracy 10m
13 TTFF (Open Sky) Cold Start
＜
38s / Warm Start
＜
15s / Hot Start
＜
2s
14 GSM/GPS Antenna Built-in design
15 LED Indicator GSM-green, GPS-blue, Power-red
16 Data Transmit TCP, SMS
SOS button /
Power Indicator
GPS Indicator
GSM Indicator
Parking
mini USB
ON / OFF Switch
Strona 5 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
5. LED Indicators Status:
GPS LED Indicator – Blue
Status Implication
Quick Flashing (interval 0.1s) Searching GPS signal
Slow flashing (flash 0.1s after every 2s ) GPS signal has been acquired successfully
Continuously in dark GPS stop working
GSM LED Indicator – Green
Status Implication
Flashing (flash 0.1s after every 1s) Receive GSM signal normally
Slow flashing (flash 0.1s every 2s) GPRS on line
Solid green Monitor function is activated
OFF No GSM Signal / SIM card not instaled
Power Status – Red
Status Implication
Flashing (interval 0.1s) Low battery
Slow flashing (interval 0.2s) Full charge
Slow flashing (flash 0.1s every 2s) Normal operating
Solid Red Charging
OFF Low battery/Power off
Notice: Ignition detection indication: three LED indicators take turns flashing.
Getting Start
Please follow below instructions for ensuring safe and correct use.
1. Install the SIM card
Place the SIM card into the device with the gold-colored side facing down.
Note: Make sure there is enough credit on the SIM card. If you will be using the GPRS function, you should pay
attention to the current SIM card GPRS charge.
2. Power on
Slide “ON/OFF” switch to power on.
3. Charging battery
• Connect the charger to power;
• This process needs 4-6 hours.
• The device can work normally when charging.
• The indicator state (please refer to 2. 2.1)
Warning：Charger from the manufacturer is recommended.
Strona 6 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
Device functions and Parameter setting
1. Settings of APN
To set up the APN parameter, please send SMS command to the number of device. The device will reply “OK”
automatically after setting successfully. The SMS command is as following:APN,APN’s name#
E.g: APN,internet# (“internet” is the APN of carrier)
The device will reply “OK” if setting successfully.
Note: The APN of some countries have user name and password, you may need to send SMS command as following:
APN,APN name,user name,password#
E.g: APN,internet,CLIENTE,AMENA#
2. SOS numbers setting
5.2.1 Add SOS number
SMS command: SOS,A,number1,number2,number3,number4#(A means add number). You could set 4 SOS numbers in
maximum
For example:
SOS,A, 13510682360,13511685136#(set 2 SOS numbers)
SOS, A,13510682360,13511685136,13612687248,13612683621# (set 4 SOS numbers)
It will reply “OK” if suceeded.
You can set SOS numbers via the platform after activating the device.
3. Delete SOS numbers
SMS: SOS, D,1,2,3,4# (D means delete SOS number)
For example: SOS, D,1# means delete the first number
SOS,D,3# means delete the third number
If you do not know the serial number, you can also delete number by SMS command like this: SOS, D,number#
For example: SOS, D, 13527852360# means delete this SOS number directly.
It will reply “OK” if succeeded to delete this number.
Note：Remotely arm/disarm, remotely monitor, checking location via SMS and receiving SOS alarm from device
must be functioned by SOS numbers only, which are pre-set.
You can set SOS numbers via the platform after activating the device.
4. Arm /Disarm
Three ways to arm/ disarm:
i. Via Parking button
Slide PK switch to “ON” to arm the device. The three LEDs will slowly circulation flashing. The device will be armed after 3
minutes. The 3 LEDs will quickly circulation flashing.
Slide PK switch to “OFF” to disarm the device.
ii. via calls
Any SOS number calls to the device (must be the SOS number), and then end up the call in 10s by the mobile side to arm
the device. The device will reply a SMS message “OK”. If the SOS number does not end up the call in 10s, it will turn to
monitoring function.
Any SOS number calls to the device (must be the SOS number), and then end up the call in 10s by the mobile side to
disarm the device (if the device is armed before). The device will reply a SMS message “OK”. If the SOS number does not
end up the call in 10s, it will enter monitoring function.
iii. via SMS command
Any SOS number can send SMS command “111” to arm the device (must be the SOS number). And the device will
automatically reply “OK” if it set successfully.
Any SOS number can send SMS command “000” to disarm the device (must be the SOS number). And the device will
automatically reply “OK” if it set successfully.
Strona 7 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
5. Vibration alarm
When the device is in arm state, vibration will activate alarms. The device will send vibration alarm to the SOS numbers in
10s.
If the GPS is located, the device will send accurate address information. If GPS is not located, the device will send LBS
address information. If GPS is located in 5 minutes, the device will send accurate address information.
Example of GPS address information:
“vibration alarm: Bao’an Road, Bao’an District, Shenzhen, Guangdong (N22.57139,E113.87710)
Example of LBS address information:
“vibration alarm: nearby Bao’an Road Bao’an District, Shenzhen, Guangdong (22.571,113.876)”.
When vibration alarm is actived, if GPS is located successfully while there is no GPRS connection, the device will send
longitude and latitude location to SOS numbers pre-set : " Vibration alarm! Location: N23.111748, E114,409215,
Date&Time: 11-04-28 10:00:48".
When vibration alarm is actived, if GPS is not located successfully and there is no GPRS connection, then device will not get
location information and send to SOS numbers pre-set :"Vibration alarm! Please notice".
Remark：The interval of vibration alarm could not be less than 5 minutes.
6. SOS alarm
Press SOS button for more than 3s to activate SOS alarm, meanwhile you could feel the vibration, and then the device will
send an address information message to the SOS number. If GPS is located, the device will send an accurate address
information,
e.g.: “Emergency call(LBS): Bao’an Road, Bao’an District, Shenzhen, Guangdong (N22.57139,E113.87710)”.
If GPS is not located, the device will send a LBS location information:
e.g.:“Emergency call(LBS): nearby Bao’an Road Bao’an District, Shenzhen, Guangdong (22.571,113.876)”.
Then it will dial the SOS numbers by cycle, if any SOS number answer the call, it will stop calling. If there’s no response
after all the number been dialed for three cycles, it will stop.
7. Geo-fence
You can set a designated area as geo-fence. When the device gets in/out of this area, it will send alarm to SOS numbers
when the geo-fence function is ON.
i. Turn on geo-fence
Geo-fence function is off as default. You can turn on geo-fence via SMS command.
Circular fence
You can set a coordinate as the centre of the circular fence and set the radius
Go in fence SMS command: “FENCE,ON,0,latitude,longitude,radius,IN#” to open circular fence function
e.g.: FENCE,ON,0,N22.57139,E113.87710,5,IN#
It means the radius is 500 meters.（radius 1=100M，2=200M····and so on）
The device will reply“OK”if set successfully. When the device is in this circular area, it will send alarm
to the SOS numbers.
Go out fence SMS: “FENCE,ON,0,latitude,longitude,radius,OUT#”to open circular fence function
e.g.: FENCE,ON,0, N22.57139,E113.87710,5,OUT #
It means the radius is 500 meters.（radius 1=100M，2=200M····and so on）
The device will reply“OK”if set successfully. When the device is out of this circular area, it will send alarm
to the SOS numbers.
Go in/out fence SMS: “FENCE,ON,0,latitude,longitude,radius#”
e.g.: FENCE,ON,0,N22.57139,E113.87710,5#
It means the radius is 500 meters（radius 1=100M，2=200M····and so on）
The device will reply“OK”if set successfully. As long as the device goes in or out of this circular area, it will send alarm to
the SOS numbers.
You can also set current location coordinates as the centre of the circular fence, SMS:
“FENCE,ON,0,0,0,radius#” (This SMS is only available when device get located)
ii. Disable Geo fence
If don’t need geo fence function, send SMS to disable it: FENCE,OFF#
After get reply “OK”, geo fence function is off.
Strona 8 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
iii. Check geo fence
If want to check status of geo fence, send SMS command "SEEFENCE#" to device from any number.
If geo fence is not active, it will reply SMS "Switch: OFF"
If geo fence is active, it will reply SMS "Switch: ON;State:IN&OUT;Lat:N22.567000;Lon:E113,890000,Radius:100M;FenceT
ype:Circle;"
8. Low battery alarm
When battery is low, device will send SMS to SOS numbers as following:
Low battery alarm SMS: “Warning! Battery is low, please charge in time!”
When battery is too low to approach power off, it will send SMS: Warning! Battery is too low, power off automatically
9. Voice monitoring
When the SOS number dials the device, keep ringing more than 10s, it will go to voice monitoring
status. In this case, caller can monitor the sound around the device.
Note: 1. Monitor function request the SIM card in device with caller ID display.
2. Only SOS numbers can monitor
10. View location method
i. Ask address information
Sending SMS command from SOS number to device: POSITION
After command is sent successfully, user will receive SMS of LBS/GPS location (depends on the situation)
Only SOS number can check location of device, other numbers will get a reply “ERROR:110”.
Situation:
If GPS is located successfully, device will reply SMS of an acurate location.
If GPS is not located, device will send LBS location first. And then if GPS located within 2mins, device will send another SMS
with accurate location.
Example of LBS address information: “ Current location (LBS): nearby Bao’an Road Bao’an District, Shenzhen, Guangdong
(22.571,113.876)”.
Example of GPS address information: “Accurate location (GPS):Bao’an Road, Bao’an District, Shenzhen, Guangdong
(N22.57139,E113.87710)
ii. Ask coordinates
SMS command: WHERE#
Apply for replying longitude and latitude from device. If GPS is located, it will reply current longitude and latitude
information. If not located within 2mins, it will reply the latest longitude and latitude information.
Examples of reply:
Lat:N22.571285,Lon:E113.877115,Course:42.20,Speed:0.0740,DateTime:10-11-23 22:28:51
If GPS is not located at all，device will reply after 2mins：“GPS is fail to locate, no data, please try again！”
iii. Ask Google link
Sending SMS command from SOS number to device: URL#
Apply for reply of google link, if GPS is located, it will reply google link of current longitude and latitude. If not located withi
n 2 mins, it will reply google link of the latest longitude and latitude:
examples of google link reply
<DateTime:10-11-23 23:42:51> http://maps. oogle.com/maps?q=N22.571490,E113.877103
If GPS has never been located before, it will reply SMS after 10mins "GPS is fail to locate, no data, please try again!"
Note: GPS can be located in the open air only; it can not be located indoor. The following conditions will be difficult for
GPS acquirement: under shade of trees, high buildings and the area with much metal material.
iv. Platform checking
The system will register login accounts according to IMEI of device automatically after the devices located by GPS/LBS
successfully first time. The website is: www.cootrack.com
You can use the IMEI marked on device to login, default password is 666666
E.g: Account --- 353419032549607
Password --- 666666
If it shows “Account is invalid, Please check it!”,it means the device is failed to locate, so please take your device outdoor
and make the GPS located successfully. And then try to login again.
Notice: The sim card should activate GPRS function.
Strona 9 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
11. Factory recovery settings
SMS command: FACTORY#
When device gets command, it will recover parameters into default value.
12. Reboot device
SMS command: RESET#
When device gets command, it will reboot after 1 min.
Troubleshooting
If there is trouble during using the phone, please read the solution as follow or contact provider.
Common problems Causes Solution
Bad reception
Radio waves can not communicate with
device when it is used in a bad signal area,
like basement or space beside tall building.
Change to a place with good signal.
Can not talk in Call-intensive period. Avoid call-intensive period
can not switch on No power Change a new battery
GPS is not locating
Keep the device indoor Locating in open space outdoor.
Weak GPS signal Keep the upside of the phone face to sky
There is metal stuff covered the phone. Move away the metal stuff.
Unable to monitor
The called number is not the SOS number Set up SOS number
SIM card without caller ID display function Active function of caller ID display
can not connect to
the network
The sheet metal of SIM card is dusty. Wipe with a clean wiper.
Invalid SIM card Contact your operator
Out of GSM service area Move back to the GSM service covered area.
weak signal Try again in a strong signal area
can not charge
Voltage is out of charging range of charger. Change to the proper voltage
Use non-standard charger Use charger that come with the package
Poor contact Check if the plug is in.
Red LED is continuous dark when charging It is because the battery is used up ,keep charging
after about half an hour, the LED will turn on
Can not check
address
information
SIM card can not support GPRS functions Please contact the sim card operator to activate GPRS
Reply “no data, please try again” all the
time Please contact with your distributors
It is not a SOS number Please set the number as SOS number
Strona 10 z 10 rev. 1.0.1
USER MANUAL: GT03B GPS PORTABLE TRACKER
www.elmic.p
l
,
[email protected]
Warranty instructions and service
1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of
purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. We reserve the
right to refuse warranty if this information has been removed or changed after the original purchase of the product from
the dealer.
2. Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of
the product itself.
3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has
been attempted by any unauthorized service centre.
4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty
period.
5. The warranty is not applicable to cases other than defects in material, design and workmanship.
Statement
All rights reserved.
Author instructions Shenzhen Concox Information Technology Co., Ltd.
Correction ELMIC / PHU FENIKS POLAND
Producer:
Shenzhen Concox Information Technology Co., Ltd.
China
www.concox.cn
Importer:
Przedsiębiorstwo Handlowo Usługowe FENIKS
ul. Słoneczna 110,
Nowa Kuźnica, 42-350 Koziegłowy
Poland
www.elmic.pl, elm[email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Shenzhen Concox Information Technology GT03B User manual

Brand
Shenzhen Concox Information Technology
Model
GT03B
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents