Porter Cable 7518 User manual

Brand: Porter Cable

Model: 7518

Category: Power tools

Type: User manual

This manual is also suitable for

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. ______________________________________

IMPORTANT

Please make certain that the person who

is to use this equipment carefully reads

and understands these instructions before

starting operations.

ESPAÑOL: PÁGINA 17

FRANÇAISE : PAGE 31

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Part No. A14100 - 09-23-05 - Rev. A

Instruction

manual

Double Insulated

Routers

MODEL 7518

Consisting of:

MODEL 75182 Motor

MODEL 75361 Base

MODEL 7519

Consisting of:

MODEL 75192 Motor

MODEL 75361 Base

TABLE OF CONTENTS

Read and understand all warnings and operating

instructions before using any tool or equipment. When

using tools or equipment, basic safety precautions should always be

followed to reduce the risk of personal injury. Improper operation,

maintenance or modification of tools or equipment could result in serious

injury and property damage. There are certain applications for which tools

and equipment are designed. Porter-Cable strongly recommends that this

product NOT be modified and/or used for any application other than for

which it was designed.

If you have any questions relative to its application DO NOT use the product

until you have written Porter-Cable and we have advised you.

Online contact form at www.porter-cable.com

Postal Mail: Technical Service Manager

Porter-Cable

4825 Highway 45 North

Jackson, TN 38305

Information regarding the safe and proper operation of this tool is available from

the following sources:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New

York, NY 10036 www.ansi.org ANSI 01.1Safety Requirements for

Woodworking Machines, and the U.S. Department of Labor regulations

www.osha.gov

SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY GUIDELINES - DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

MAINTENANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals

known (to the State of California) to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, al ways wear

NIOSH/OSHA approved, properly fit ting face mask or res pi ra tor when us ing

such tools.

CALIFORNIA PROPOSITION 65

It is important for you to read and understand this manual. The

information it contains relates to protecting YOUR SAFETY and

PREVENTING PROBLEMS. The symbols below are used to help

you recognize this information.

SAFETY GUIDELINES - DEFINITIONS

indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not

avoided,could result in death or serious injury.

indicates a potentially haz ard ous situation which, if not

avoided,may result in minor or mod er ate injury.

used without the safety alert symbol indicates potentially

hazardous situation which, if not avoided, may result in

property damage.

Read all instructions. Failure to follow all

instructions listed below may result in electric

shock, fire and/or serious injury. The term "power tool" in all

of the warnings listed below refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use reduces

the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal

injury.

b) Use safety equipment. Always wear eye protection. Safety equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position

before plugging in. Carrying power tools with your finger on the switch

or plugging in power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

GENERAL SAFETY RULES

may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewelry or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to

operate the power tool. Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tools operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance

with these instructions and in the manner intended for the particular

type of power tool, taking into account the working conditions

and the work to be performed. Use of the power tool for operations

different from those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using

only identical replacement parts. This will ensure that the safety of the

power tool is maintained.

GENERAL SAFETY RULES

continued

1. HOLD POWER TOOL BY INSULATED GRIPPING SURFACES WHEN

PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY

CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

2. USE CLAMPS OR OTHER PRACTICAL WAY TO SECURE AND SUPPORT

THE WORKPIECE TO A STABLE PLATFORM. Holding the work by hand or

against your body is unstable and may lead to loss of control.

3. DISCONNECT TOOL FROM POWER SOURCE before making adjustments

or changing bits.

4. TIGHTEN COLLET NUT securely to prevent the bit from slipping.

5. USE A CLAMP or some other device to hold the workpiece rigidly in position.

and clear the path of the tool of obstructions.

6. PROVIDE CLEARANCE under workpiece for router bit when through-cutting.

7. CHECK TO SEE THAT THE CORD will not “hang up” during routing operation.

8. CLEAR THE ROUTER BIT AREA before starting motor.

9. MAINTAIN FIRM GRIP on router to resist starting torque.

10. KEEP HANDS CLEAR OF BIT when motor is running to prevent personal injury.

11. KEEP CUTTING PRESSURE CONSTANT. Do not overload motor.

12. LET THE MOTOR COME TO A COMPLETE STOP before putting the tool down.

13. NEVER TOUCH router bits after use. They may be extremely hot.

14. NEVER TIGHTEN COLLET NUT without a bit.

15. DO NOT USE ROUTER BITS with a diameter in excess of 2-1/2" at RPM above

13,000. Router bits up to 3-1/2" in diameter can be used when speed control is

set for 13,000 RPM or less.

16. ALWAYS KEEP CHIP SHIELD clean and in place.

17. AVOID “CLIMB-CUTTING” (see “Using The Router” section in this manual).

“Climb-cutting” increases the chance for loss of control resulting in possible

personal injury.

18. DO NOT HAND-HOLD THE ROUTER IN AN UPSIDE-DOWN OR HORIZONTAL

POSITION. The motor can separate from the base if not properly attached

according to the instructions.

19. Wear eye and hearing protection. Always use safety glasses. Everyday

eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.

Eye protection equipment should comply with ANSI Z87.1 standards. Hearing

equipment should comply with ANSI S3.19 standards.

20.

Use of this tool can generate and disburse dust or other

airborne particles, including wood dust, crystalline silica dust and asbestos

dust. Direct particles away from face and body. Always operate tool in well

ventilated area and provide for proper dust removal. Use dust collection system

wherever possible. Exposure to the dust may cause serious and permanent

respiratory or other injury, including silicosis (a

serious lung disease), cancer,

and death. Avoid breathing the dust, and avoid prolonged contact with dust.

Allowing dust to get into your mouth or eyes, or lay on your skin may promote

absorption of harmful material. Always use properly fitting NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure, and wash

exposed areas with soap and water.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS!

SYMBOL DEFINITION

V ........................................ volts

A ........................................ amperes

Hz ...................................... hertz

W ....................................... watts

kW ..................................... kilowatts

F ........................................ farads

µF ...................................... microfarads

l .......................................... litres

g ........................................ grams

kg ....................................... kilograms

bar ..................................... bars

Pa ...................................... pascals

h ........................................ hours

min ..................................... minutes

s ......................................... seconds

0 .......................................

no-load speed

.../min or …min

..............

Revolutions or reciprocations per minute

or d.c. .................... direct current

or a.c. ....................... alternating current

............................ two-phase alternating current

2N ........................... two-phase alternating current with neutral

.............................. three-phase alternating current

3N ............................ three-phase alternating current with neutral

.............................. rated current of the appropriate fuse-link in amperes

................................. time-lag miniature fuse-link where X is the symbol for

the time/current characteristic, as given in IEC 60127

................................... protective earth

.................................... class II tool

IPXX ................................... IP symbol

FUNCTIONAL DESCRIPTION

Model 7518 Porter-Cable Router incorporates a speed control that provides

operating speeds from 10,000 RPM to 21,000 RPM, to handle the most

demanding router applications in various materials.

Model 7519 Porter-Cable Router is designed for continuous, rugged operations

to handle the most demanding routing applications at 21,000 RPM.

* Router

* Open-end wrenches (2)

CARTON CONTENTS

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to

prevent excessive voltage drop which will cause loss of power and possible

motor damage. A table of recommended extension cord sizes will be found in this

section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230

volts) at 150% of rated amperes.

If an extension cord is to be used outdoors, it must be marked with the suffix W-A

or W following the cord type designation. For example – SJTW-A to indicate it is

acceptable for outdoor use.

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60

cycle A.C. current and voltage within plus or minus 5 percent of that shown on

the specification plate on the tool. Several models, however, are designed for A.C.

current only. Refer to the specification plate on your tool for proper voltage and

current rating.

Do not operate your tool on a current on which the voltage

is not within correct limits. Do not operate tools rated A.C.

only on D.C. current. To do so may seriously damage the tool.

SAVE THESE INSTRUCTIONS!

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.

230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.

Nameplate Ampere Rating

0-2 18 18 18 16 16 14 14 12 12

2-3 18 18 16 14 14 12 12 10 10

3-4 18 18 16 14 12 12 10 10 8

4-5 18 18 14 12 12 10 10 8 8

5-6 18 16 14 12 10 10 8 8 6

6-8 18 16 12 10 10 8 6 6 6

8-10 18 14 12 10 8 8 6 6 4

10-12 16 14 10 8 8 6 6 4 4

12-14 16 12 10 8 6 6 6 4 2

14-16 16 12 10 8 6 6 4 4 2

16-18 14 12 8 8 6 4 4 2 2

18-20 14 12 8 6 6 4 4 2 2

SELECTING THE BIT

Models 7518 and 7519 accommodate bits with 1/2" diameter shanks that are

installed directly into the power unit collet. Collets are available that will allow the

use of bits having 1/4" or 3/8" diameter shanks.

DON’T USE router bits with a diameter in excess of 2

/2"

except when using Model 75182 motor set for either

10,000 or 13,000 RPM. Router bits with a diameter up to 3" may be used

with the 75182 motor operating in the 10,000 or 13,000 RPM speeds.

Router bits with a diameter up to 3

/2" may be used with the 75182 motor

operating in the 10,000 RPM speed.

OPERATION

INSTALLING AND REMOVING THE BIT

Disconnect tool from power source.

1. To remove motor unit from base unit:

(a) Open the clamp (A) Fig. 1.

(b) While holding base,

turn motor unit

COUNTERCLOCKWISE

until lower pin (B) in motor

housing is disengaged from

groove in base.

unit.

2. Clean and insert shank of bit

into collet at least 3/4". If shank

“bottoms” in router, then back it out approximately 1/16" to allow proper

tightening.

3. Lay the power unit on its side on a bench with the collet pointing AWAY from

you.

4. Place one wrench on flats on

chuck with the opposite end

of the wrench resting on the

bench to your left, Fig. 2.

5. Place other wrench

on collet and tighten

COUNTERCLOCKWISE as

shown in Fig. 2. TIGHTEN

SECURELY.

6. To remove the bit, reverse the

above procedure. If bit does

not remove easily, tap the collet nut with wrench to release.

Avoid possible damage to collet. Never tighten collet without

a bit.

NOTE: This tool is shipped completely assembled. No assembly time or tools are

required.

ASSEMBLY

Fig. 1

Fig. 2

INSTALLING THE MOTOR

Disconnect tool from power source.

1. Loosen the clamp screw (A), Fig. 1, to allow the power unit to be set in the

base unit.

2. Insert motor unit into base aligning lower pin (B) with groove in base.

3. Rotate motor unit CLOCKWISE into base until upper guide pins are rigidly

set in the groove of the base.

4. Tighten clamp screw firmly.

ADJUSTING DEPTH

OF CUT

Disconnect tool from power

source.

1. Loosen clamp screw (A)

Fig. 3.

2. While holding base (E),

turn motor unit (F), Fig. 3,

COUNTERCLOCKWISE

until the tip of the bit is

above bottom surface of

base.

3. Set router on flat wood

surface.

4. Turn motor unit (F), Fig.

3, CLOCKWISE until

bit touches the wood

surface.

5. Tighten clamp screw (A)

Fig. 3.

6. Rotate depth adjusting

ring (B), Fig. 3, until the zero-line (C) is opposite the index line (D) on the

housing.

7. Loosen clamp screw (A), Fig. 3.

8. Tip the router so bit is clear of the wood surface. Turn motor unit (F),

Fig. 3, CLOCKWISE until the index line (D) on the motor housing reaches the

desired depth indicated on the ring.

9. Tighten clamp screw (A), Fig. 3, firmly.

NOTE: Setting the index line to

/4" on the ring means the cutting edge of the bit

is exposed

/4" below the base.

CONNECTING TO POWER SOURCE

Before connecting router to power source ALWAYS MAKE

SURE SWITCH IS IN THE “OFF” POSITION. Also check that

the power circuit is the same as that shown on specification plate of the

router.

Fig. 3

TO START AND STOP ROUTER

Before starting the router make sure bit is clear of

workpiece and foreign objects. Also keep firm grip on router

to resist starting torque.

The router is started and stopped by depressing the rocker switch (A), Fig. 4, into

the "ON" or "OFF" position.

To avoid personal injury or damage to finished work always

allow the motor to come to a COMPLETE STOP before

setting it down.

OVERLOAD PROTECTION

Model 7518 is equipped with an overload protector that will shut motor off if

prolonged overload conditions are encountered.

If the motor stops during use: (1) depress rocker switch (A), Fig. 4, into the "OFF"

position; (2) determine cause of overload (i.e. dull bit, low voltage, excessive feed

rate, etc.) and correct before continuing; (3) restart router following the instructions

in TO START AND STOP ROUTER.

Model 7519 is equipped with a thermal-type circuit breaker incorporated into the

ON/OFF rocker switch (A), Fig. 4. This circuit breaker will turn the switch "OFF" if

prolonged overload conditions are encountered.

If the circuit breaker “trips”, switching the motor "OFF": (1) determine cause

of the overload (i.e. dull bit, low voltage, excessive feed rate, etc.) and correct

before continuing; (2) allow router to cool for three minutes; and, (3) restart router

following the instructions in TO START AND STOP ROUTER.

SOFT START

Model 7518 and 7519 have a “Soft Start” feature designed to minimize startup

reaction torque.

SPEED CONTROL (Model 7518 only)

The speed control is located as shown in Fig. 4. Five operating speeds from 10,000

RPM to 21,000 RPM are available by moving the speed selector knob (B), Fig. 4.

It is recommended that the speed be set prior to engaging the router bit into work.

Should it be necessary to change the speed after work has begun, stop router,

remove router clear of work, and adjust speed setting.

MODEL 7518 MODEL 7519

Fig. 4

USING THE ROUTER

IMPORTANT: Before using your router, consider the kind and total amount of

material to be removed. Depending on the material, it may be necessary to make

more than one cut to avoid overloading the motor. Before beginning the cut on

the actual workpiece, it is advisable to make a sample cut on a piece of scrap

lumber. This will show exactly how the cut will look as well as enable you to

check dimensions.

Always be sure the work is rigidly clamped or otherwise

secured before making a cut.

IMPORTANT: Before using your router, consider the kind and total amount of

material to be removed. Depending on the material, it may be necessary to make

more than one cut to avoid overloading the motor. Before beginning the cut on

the actual workpiece, it is advisable to make a sample cut on a piece of scrap

lumber. This will show exactly how the cut will look as well as enable you to

check dimensions.

Always be sure the work is rigidly clamped or otherwise secured before making a

cut.

Generally speaking, when working on a bench, the workpiece should be held on

the bench by wood clamps. When routing edges, the router should be held firmly

down and against the work by both handles.

Since the cutter rotates clockwise (when viewing router from top), the router

should be moved from left to right as you stand facing the work (see Fig. 5). When

working on the inside of a templet, move router in clockwise direction. When

working on the outside of a templet, move router in a counterclockwise direction.

Avoid “Climb-

Cutting” (cutting

in direction opposite that shown in

Fig. 5), “Climb-Cutting” increases the

chance for loss of control resulting in

possible personal injury. When “Climb-

Cutting” is required (backing around a

corner), exercise extreme caution to

maintain control of router.

The speed and depth of cut will depend

largely on the type of material being

worked upon. Keep the cutting pressure constant but do not crowd the router so

the motor speed slows excessively. It may be necessary on exceptionally hard

woods or problem materials to make more than one pass at various settings to

get the desired depth of cut.

When making cuts on all four edges of the workpiece, it is advisable to have the

first cut on the end of the piece across the grain. Thus, if chipping of wood occurs

at the end of a cut, it will be removed when making the next cut parallel with the

grain.

THE EDGE GUIDE

An edge guide is available as an accessory to aid in routing operations such as:

straight edge planing, parallel grooving, dado or slotting operations.

To assemble, insert guide rods (A) in holes in base, Fig. 6, and secure with screws

(B). The guide (C) is adjusted on the rods and secured in desired position with

thumb screws (D)

Fig. 5

TEMPLET GUIDES

A wide variety of templet guides are available for use in pattern and templet

routing operations. Fig. 7 shows a typical combination bit, templet guide, and

locknut.

Disconnect the tool from the power source.

To install, insert templet guide in center hole in router base and secure in place

with the locknut.

NOTE: Before connecting the router to the power source, install, the bit, adjust

depth of cut, and rotate the router chuck by hand to be sure the bit or the collet

do not contact the templet guide.

For assistance with your tool, visit our website at www.porter-cable.com for a

list of service centers or call the Porter-Cable help line at 1-800-487-8665.

TROUBLESHOOTING

Fig. 6

LOCKNUT

ROUTER BIT

TEMPLET GUIDE

SUB-BASE

BASE

Fig. 7

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts

should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic

parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed

air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are

making good contact in the outlet. Also, check for blown fuses or open circuit

breakers in the line.

BRUSH INSPECTION (If applicable)

For your continued safety and electrical protection, brush inspection and

replacement on this tool should ONLY be performed by an AUTHORIZED

PORTER-CABLE SERVICE STATION or a PORTER-CABLE

·DELTA

FACTORY SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest

authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.

Have worn parts replaced and lubricated with fresh lubricant. Have new brushes

installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need

for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL

UNDER THIS CONDITION. If proper operating voltage is present, return your tool

to the service station for immediate service.

MAINTENANCE

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at

servicenet.porter-cable.com. You can also order parts from your nearest factory-owned

branch, or by calling our Customer Care Center at 1-800-223-7278 to receive personalized

support from highly-trained technicians.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For

information about Porter-Cable, its factory-owned branches, or an Authorized Warranty

Service Center, visit our website at www.porter-cable. com or call our Customer Care

Center at 1-800-223-7278. All repairs made by our service centers are fully guaranteed

against defective material and workmanship. We cannot guarantee repairs made or

attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North,

Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model number, type, serial number, etc.).

A complete line of accessories is available from your Porter-Cable·Delta

Supplier, Porter-Cable

·Delta Factory Service Centers, and Porter-Cable

Authorized Service Stations. Please visit our Web Site www.porter-cable.

com for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Porter-

Cable·Delta have not been tested with this product, use

of such accessories could be hazardous. For safest operation, only Porter-

Cable

·Delta recommended accessories should be used with this product.

ACCESSORIES

PORTER-CABLE LIMITED

ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original

purchase. We will repair or replace at our option, any part or parts of the product and accessories

covered under this warranty which, after examination, proves to be defective in workmanship or

material during the warranty period. For repair or replacement return the complete tool or accessory,

transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.

Proof of purchase may be required. This warranty does not apply to repair or replacement required

due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service

Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE

OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,

4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING

OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY

AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary

from state to state.

WARRANTY

Número de parte A14100 - 09-23-05 - Rev. A

ENGLISH: PAGE 1

FRANÇAISE : PAGE 31

La placa de Modelo y de Número de Serie está

localizada en la caja principal de la herramienta. Anote

estos números en las líneas de abajo y guárdelos para

su referencia en el futuro.

Número de modelo ______________________________

Tipo ___________________________________________

Número de serie ________________________________

IMPORTANTE

Asegúrese de que la persona que va a usar esta

herramienta lea cuidadosamente y comprenda estas

instrucciones antes de empezar a operarla.

Para obtener más información

sobre Porter-Cable,

visite nuestro sitio web en:

http://www.porter-cable.com

Manual de

Instrucciones

Contorneadores

(Ráuteres) con

Aislamiento Doble

MODELO 7518

Consiste de:

Motor, MODELO 75182

Base, MODELO 75361

MODELO 7519

Consiste de:

Motor, MODELO 75192

Base, MODELO 75361

Es importante para usted leer y entender este manual. La información que lo

contiene relaciona a proteger SU SEGURIDAD y PREVENIR los PROBLEMAS.

Los símbolos debajo de son utilizados para ayudarlo a reconocer esta

información.

Indica una situación de inminente riesgo, la cual, si no es evitada,

causará la muerte o lesiones serias.

Indica una situación potencialmente riesgosa, que si no es

evitada, podría resultar en la muerte o lesiones serias.

Indica una situación potencialmente peligrosa, la cual, si no es

evitada, podría resultar en lesiones menores o mode-radas.

Usado sin el símbolo de seguridad de alerta indica una situa-

ción potencialmente riesgosa la que, si no es evitada, podría

causar daños en la propiedad.

Algunos tipos de aserrín creados por máquinas eléctricas de

lijado, aserrado, amolado, perforado u otras actividades de

la construcción, contienen materiales químicos conocidos (en el Estado de California)

como causantes de cáncer, defectos de nacimiento u otros daños del aparato

reproductivo. Algunos ejemplos de dichos productos químicos son:

• El plomo contenido en algunas pinturas con base de plomo

• Sílice cristalizado proveniente de los ladrillos, el cemento y otros productos de

albañilería

• Arsénico y cromo de madera tratada químicamente

Su riesgo por causa de estas exposiciones varía, dependiendo de con cuánta frecuencia

realice este tipo de trabajo. Para reducir su exposición a estos agentes químicos: trabaje en

un área bien ventilada y trabaje con equipo de seguridad aprobado, use siempre protección

facial o respirador NIOSH/OSHA aprobados cuando deba utilizar dichas herramientas.

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

PAUTAS DE SEGURIDAD/DEFINICIONES

GUARDE ESTAS INSTRUCCIONES!

Lea y entienda todas advertencias y las instrucciones

operadoras antes de utilizar cualquier instrumento o el

equipo. Cuando se usa instrumentos o equipo, las precauciones básicas de la

seguridad siempre se deben seguir para reducir el riesgo de la herida personal. La

operación impropia, la conservación o la modificación de instrumentos o equipo

podrían tener como resultado el daño grave de la herida y la propiedad. Hay ciertas

aplicaciones para que equipaas con herramienta y el equipo se diseña. La Porter-

Cable recomienda totalmente que este producto no sea modificado y/o utilizado

para ninguna aplicación de otra manera que para que se diseñó.

Si usted tiene cualquiera pregunta el pariente a su aplicación no utiliza el producto hasta

que usted haya escrito Porter-Cable y nosotros lo hemos aconsejado.

La forma en línea del contacto en www. porter-cable. com

El Correo Postal: Technical Service Manager

Porter-Cable

4825 Highway 45 North

Jackson, TN 38305

Información con respecto a la operación segura y apropiada de este instrumento está

disponible de las fuentes siguientes:

Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive, Itasca, IL 60143-3201

American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036

www.ansi.org ANSI 01.1Safety Requirements for Woodworking Machines, and the

U.S. Department of Labor regulations

www.osha.gov

Lea todas las instrucciones. Si no se siguen

todas las instrucciones que aparecen a

continuación, el resultado podría ser sacudidas eléctricas, incendio y/

o lesiones graves. La expresión "herramienta mecánica" en todas las

advertencias que aparecen a continuación se refiere a su herramienta

mecánica alimentada por la red eléctrica (herramienta alámbrica) o su

herramienta mecánica alimentada por baterías (herramienta inalámbrica).

GUARDE ESTAS INSTRUCCIONES

1) Seguridad del área de trabajo

a) Mantenga el área de trabajo limpia y bien iluminada. Las áreas

desordenadas u oscuras invitan a que se produzcan accidentes.

b) No utilice herramientas mecánicas en atmósferas explosivas, como

por ejemplo en presencia de líquidos, gases o polvos inflamables. Las

herramientas mecánicas generan chispas que pueden incendiar el polvo o

los vapores.

c) Mantenga alejados a los niños y a las personas que estén presentes

mientras esté utilizando una herramienta mecánica. Las distracciones

pueden hacerle perder el control de la herramienta.

2) Seguridad eléctrica

a) Los enchufes de las herramientas mecánicas deben coincidir con el

tomacorriente. No modifique nunca el enchufe de ningún modo. No

use enchufes adaptadores con herramientas mecánicas conectadas a

tierra (puestas a tierra). Los enchufes no modificados y los tomacorrientes

coincidentes reducirán el riesgo de sacudidas eléctricas.

b) Evite el contacto del cuerpo con las superficies conectadas o puestas

a tierra, tales como tuberías, radiadores, estufas y refrigeradores. Hay

un aumento del riesgo de sacudidas eléctricas si el cuerpo del operador se

conecta o pone a tierra.

c) No exponga las herramientas mecánicas a la lluvia o a condiciones

mojadas. La entrada de agua en una herramienta mecánica aumentará el

riesgo de que se produzcan sacudidas eléctricas.

d) No maltrate el cordón de energía. No use nunca el cordón para

transportar la herramienta mecánica, tirar de ella o desenchufarla.

Mantenga el cordón alejado del calor, el aceite, los bordes afilados o las

piezas móviles. Los cordones dañados o enganchados aumentan el riesgo

de que se produzcan sacudidas eléctricas.

e) Cuando utilice una herramienta mecánica en el exterior, use un cordón

de extensión adecuado para uso a la intemperie. La utilización de un

cordón adecuado para uso a la intemperie reduce el riesgo de que se

produzcan sacudidas eléctricas.

3) Seguridad personal

a) Manténgase alerta, fíjese en lo que está haciendo y use el sentido

común cuando esté utilizando una herramienta mecánica. No use una

herramienta mecánica cuando esté cansado o bajo la influencia de

drogas, alcohol o medicamentos. Un momento de distracción mientras

esté utilizando herramientas mecánicas podría causar lesiones corporales

graves.

b) Use equipo de seguridad. Use siempre protección de los ojos. El

equipo de seguridad, como por ejemplo una máscara antipolvo, calzado

de seguridad antideslizante, casco o protección de oídos, utilizado para las

condiciones apropiadas, reducirá las lesiones corporales.

c) Evite el arranque accidental. Asegúrese de que el interruptor esté

en la posición de apagado antes de enchufar la herramienta. Si se

transportan herramientas mecánicas con el dedo en el interruptor o se

enchufan herramientas mecánicas que tengan el interruptor en la posición

de encendido, se invita a que se produzcan accidentes.

NORMAS GENERALES DE SEGURIDAD

d) Quite todas las llaves de ajuste o de tuerca antes de encender la

herramienta mecánica. Una llave de tuerca o de ajuste que se deje

colocada en una pieza giratoria de la herramienta mecánica podría causar

lesiones corporales.

e) No intente alcanzar demasiado lejos. Mantenga un apoyo de los pies y

un equilibrio apro

piados en todo momento. Esto permite controlar mejor

la herramienta mecánica en situaciones inesperadas.

f) Vístase adecuadamente. No use ropa holgada ni alhajas holgadas.

Mantenga el pelo, la ropa y los guantes alejados de las piezas móviles.

La ropa holgada, las alhajas holgadas o el pelo largo pueden quedar

atrapados en las piezas móviles.

g) Si se proporcionan dispositivos para la conexión de instalaciones

de extracción y recolección de polvo, asegúrese de que dichas

instalaciones estén conectadas y se usen correctamente. El uso de estos

dispositivos puede reducir los peligros relacionados con el polvo.

4) Uso y cuidado de las herramientas mecánicas

a) No fuerce la herramienta mecánica. Use la herramienta mecánica

correcta para la aplicación que desee realizar. La herramienta mecánica

correcta hará el trabajo mejor y con más seguridad a la capacidad nominal

para la que fue diseñada.

b) No use la herramienta mecánica si el interruptor no la enciende y apaga.

Toda herramienta mecánica que no se pueda controlar con el interruptor es

peligrosa y debe ser reparada.

c) Desconecte el enchufe de la fuente de energía antes de hacer cualquier

ajuste, cambiar accesorios o almacenar herramientas mecánicas.

Dichas medidas preventivas de seguridad reducen el riesgo de arrancar

accidentalmente la herramienta mecánica.

d) Guarde las herramientas que no esté usando fuera del alcance de

los niños y no deje que personas que no estén familiarizadas con la

herramienta mecánica o con estas instrucciones utilicen la herrramienta.

Las herramientas mecánicas son peligrosas en manos de usuarios que no

hayan recibido capacitación.

e) Mantenga las herramientas mecánicas. Compruebe si hay piezas

móviles desalineadas o que se atoran, si hay piezas rotas y si existe

cualquier otra situación que podría afectar el funcionamiento de la

herramienta mecánica. Si la herramienta mecánica está dañada, haga

que la reparen antes de usarla. Muchos accidentes son causados por

herramientas mecánicas mantenidas deficientemente.

f) Mantenga las herramientas de corte afiladas y limpias. Es menos

probable que las herramientas de corte mantenidas apropiadamente, con

bordes de corte afilados, se atoren, y dichas herramientas son más fáciles de

controlar.

g) Use la herramienta mecánica, los accesorios, las brocas de la

herramienta, etc., de acuerdo con estas instrucciones y de la manera

prevista para el tipo específico de herramienta mecánica, teniendo en

cuenta las condiciones de trabajo y el trabajo que se vaya a realizar. El

uso de la herramienta mecánica para operaciones distintas a aquéllas para

las que fue diseñada podría causar una situación peligrosa.

5) Servicio de ajustes y reparaciones

a) Haga que su herramienta mecánica reciba servicio de un técnico de

reparaciones calificado, utilizando únicamente piezas de repuesto

idénticas. Esto asegurará que se mantenga la seguridad de la herramienta

mecánica.

NORMAS GENERALES DE SEGURIDAD

(continuación)

Page is loading ...

Porter Cable 7518 User manual

Brand: Porter Cable

Model: 7518

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Porter Cable 7518 Manuel utilisateur
español: Porter Cable 7518 Manual de usuario

Porter Cable 7518 User manual

This manual is also suitable for

Porter Cable 7518 User manual

in other languages

Related papers

Other documents