ACME LED Move 600SE User manual

Brand: ACME

Model: LED Move 600SE

Category: Floodlights

Type: User manual

This manual is also suitable for

LED?MS600SE

LED‐MS600SE





UserGuide



ProfessionalLEDMovingHead

CONTENTS



1.SafetyInstruction..............................................................................................2

2.TechnicalSpecifications ....................................................................................3

3.HowToSetTheUnit .........................................................................................4

3.1ControlPanel ..............................................................................................4

3.2GoboWheel................................................................................................5

3.3MainFunction.............................................................................................6

3.4HomePositionAdjustment.......................................................................11

4.ControlByUniversalDMXController .............................................................14

4.1DMX512Connection................................................................................14

4.2DMXAddressSetting ................................................................................15

4.3DMX512Configuration .............................................................................16

5.Troubleshooting..............................................................................................18

6.FixtureCleaning..............................................................................................20

 1.SafetyInstruction

WARNING

PleasekeepthisUserGuideforfutureconsultation.Ifyouselltheunittoanotheruser,besure

thattheyalsoreceivethisinstructionmanual.

Important:

Damagescausedbythedisregard ofthisusermanualarenotsubjecttowarranty.The

dealerwillnotacceptliabilityforanyresultingdefectsorproblems.

y Unpackandcheckcarefullythatthereisnotransportationdamagebeforeusingtheunit.

y Theunitisforindooruseonly.Useonlyinadrylocation.

y DOinstallandoperatebyqualifiedoperator.

y DONOTallowchildrentooperatethefixture.

y Use safety chain when fixing the unit. Hand le the unit by carrying its base instead of head

only.

y Theunitmustbeinstalledina locationwithadequateventilation,atleast50cmfromadjacent

surfaces.

y Besurethatnoventilationslotsareblocked,otherwisetheunitwillbeoverheated.

y Before operating, ensure that the voltage and frequency of power supply match the power

requirementsoftheunit.

y It’simportanttogroundtheyellow/greenconductortoearthinordertoavoidelectricshock.

y MaximumambienttemperatureTa:40℃.DONOToperateitwhenthetemperatureishigher.

DONOTconnectthedevicetoanydimmerpack.

y Duringinitialstart ‐upsomesmokeorsmell mayarise.Thisisanormalprocessanddoesnot

necessarilymeanthatthedeviceisdefective,anditwilldecreasegraduallywithin15minutes.

y Make sure there are no flammable 

materials close to the unit while operating to avoid fire

hazard.

y Examinethepowerwirescarefully,replacethemimmediatelyifthereisanydamage.

y Unit’s surface temperature may reach up to 85℃. DO NOT touch the housing bare‐handed

during itsoperation,and allow about 15 minutesfor cooling the unit down before replacing

bulbormaintenanceasitcouldbeveryhot.

y Avoidanyinflammableliquids,waterormetalobjectsenteringtheunit.Onceithappens,cut

Pleasereadcarefullytheinstruction,whichincludesimportant

informationabouttheinstallation,usageandmaintenance.

offthemainspowerimmediately.

y DONOToperateindirtyordustyenvironment,docleanfixturesregularly.

y DONOTtouchanywireduringoperationastheremightbeahazardofelectricshock.

y Avoidpowerwirestogethertwistothercables.

y Theminimumdistancebetweenlightoutputandtheilluminatedsurfacemustbemorethan

2.5

meters.



y Disconnectmainspowerbeforefuse/lampreplacementorservicing.

y Replacefuse/lamponlywiththesametype.

y Intheeventofseriousoperatingproblem,stopusingtheunitimmediately.

y Neverturnonandofftheunittimeaftertime.

y Thehousing,the lenses,ortheultravioletfiltermustbereplacediftheyarevisiblydamaged.

y DONOTopentheunitastherearenouserserviceablepartsinside.

y Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

y Disconnectthemainspowerifthefixtureishasnotbeenusedforalongtime.

y DOusetheoriginalpackingmaterialsbeforetransportingitagain.

Caution：

y To prevent or reduce the risk of electrical

shock or fire, do not expose the unit to rain or

moisture.

y Hotlampexplosionhazard.Donotopentheunitwithin15minutesafterswitchingoff.

y DOreplacethebulbonceitisdamaged,deformedorlife‐expired.

y DONOTlookdirectlyatthelightwhilethe

bulbison.

y Nevertouchbulbwithbarefingers,asitisveryhotafterusing.

y DONOTstartontheunitwithoutbulbenclosureorwhenhousingisdamaged.

 2.TechnicalSpecifications

y DMXChannels:14&15channels

y Greatbuilt‐inlightingshowsunderMaster/Slavemodetriggeredbymusic

y Smooth0~100%dimmingandvariablestrobespeeds

y MotorizedfocusbyDMXcontrol

y AutomaticPan/Tiltpositioncorrection

y Excellentventilation,ensuringreliableoperation

y Voltage：AC100‐240V~50/60Hz

y Powerconsumption:226W

y LightSource:1x150WLED

y Fuse:6.3A

y Dimension:327x247x526mm

y Weight:14Kgs

 3.HowToSetTheUnit

3.1ControlPanel

FrontviewRearview

①

Display:



Showthevariousmenusandtheselectedfunctions

②

LED:



 DMXOnDMXinputpresent

 MASTEROnMasterMode

 SLAVEOnSlaveMode

 SOUNDFlashingSoundactivation



③Button:

 MENUToselecttheprogrammingfunctions

 DOWNTogobackwardintheselectedfunctions

 UPTogoforwardintheselectedfunctions

 ENTERTo confirmtheselectedfunctions

④OnlyForRemoteControl:



ConnectingwithCA‐8/ C A ‐9RTXtocontroltheunitforStandby,FunctionandModefunction.

⑤DMXinput/output:

ForDMX512link,use3/5 ‐pinXLRplugcabletolinktheunittogether.

⑥Mainsinput:

Connecttosupplymainspower.

⑦Mainsoutput:

Connecttosupplymainspowerforthenextunit.

3.2GoboWheel

DANGER!

Installthegoboswiththedeviceswitchedoffonly.

Unplugfrommainsbeforechanginggobos!

3.3MainFunction

To select any of the given functions, press the MENU button up to when the required one is

showingonthedisplay.SelectthefunctionbyENTERbuttonandthe displaywillblink.UseDOWN

and UP button to change the mode. Once the required mode has been selected, Press ENTER

buttontostore.BacktothemainfunctionswithoutanychangepresstheMENUbuttonorwaitfor

8seconds.

HoldMENUbuttontoquitmenumode,theunitwillrunthebuilt‐inprogramyouselected.

Themainfunctionsareshownbelow:

DMXAddress

Select DMX Address, press the ENTER button to confirm, the present address will blink on the

display.UsetheUPandDOWNbuttontoadjusttheaddressfrom1to512.Oncetheaddresshas

beenselected,presstheENTER buttontosetup, to go backtothefunctions withoutanychange

presstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwaitforone

minutetoexitthemenumode.



ChannelMode

SelectChannelMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.

Use the DOWN and UP button to select the 14 Ch or 15 Ch Mode. Once the mode has been

selected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychangepress

the MENU button again. Hold and press the MENU button about one second or wait for one

minutetoexitthemenumode.



ShowMode

SelectShowMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheShow1orShow2orShow3orShow4mode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SlaveMode

SelectSlaveMode,presstheENTER buttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheSlave1(normal)orSlave2(2lightshow)mode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



BlackoutMode

SelectBlackoutMode,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.

UsetheDOWNandUPbuttontoselecttheM/S(Master/Slave),HoldorBlackoutMode.Oncethe

modehasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SoundState

SelectSoundState,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheOn(soundon)orOff(soundoff)mode.Oncethemode

hasbeenselected,presstheENTERbuttontosetup,togobacktothefunctionswithoutany

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



SoundSense

Select Sound Sense, pressthe ENTER button to confirm, present mode will blink on the display.

UsetheDOWNandUPbuttontochangethesoundsensefrom0…100.Oncethemodehasbeen

selected,presstheENTERbuttontosetup,togobacktothefunctionswithoutanychangepress

the MENU button again. Hold and press the MENU button about one second or wait for one

minutetoexitthemenumode.



PanInverse

SelectPanInverse,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheYes(paninversion)orNo(normal)mode.Oncethemode

has been selected, press the ENTER button to setup, to go back to the functions without any

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



10B

TiltInverse

SelectTiltInverse,presstheENTERbuttontoconfirm,presentmodewillblinkonthedisplay.Use

theDOWNandUPbuttontoselecttheYes(tiltinversion)orNo(normal)mode.Oncethemode

has been selected, press the ENTER button to setup, to go back to the functions without any

changepresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwait

foroneminutetoexitthemenumode.



BackLight

SelectBackLight,presstheENTERbuttontoconfirm,presentmodewill blinkonthedisplay.Use

the DOWN and UP button to selectthe On (LED on) or Off (LED off) Mode.Once the mode has

beenselected,presstheENTER buttontosetup, to go backtothefunctions withoutanychange

presstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutonesecondorwaitforone

minutetoexitthemenumode.



FocusAdjust

Select Focus Adjust, pressthe ENTER button to confirm, presentmode will blink on the display.

UsetheDOWNandUPbuttontochangethevaluefrom0…255.Onceselected,presstheENTER

button to setup, to go back to the functions without any change press the MENU button again.

Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.



AutoTest

SelectAutoTest,pressingENTERbuttonandtheunitwillrunself‐testbybuilt‐inprogram.Togo

backtothefunctionspresstheMENUbuttonagain.HoldandpresstheMENUbuttonaboutone

secondorwaitforoneminutetoexitthemenumode.



Temp.

SelectTemp.,pressingENTERbuttonandthedisplaywillshowthetemperatureoftheunit.Togo

11B

backtothefunctionspresstheMENUbuttonagain.Hold andpresstheMENUbuttonaboutone

secondorwaitforoneminutetoexitthemenumode.



FixtureTime

Select Fixture Time, pressing ENTER button and the display will show the number of working

hoursof the unit. Togo back to the functions presstheMENU button again. Hold and pressthe

MENUbuttonaboutonesecondorwaitforoneminutetoexitthemenumode.



FirmwareVersion

SelectFirmwareVersion,pressingENTERbuttonandthedisplaywill showtheversionofsoftware

ofthe unit.To gobackto thefunctionspresstheMENUbuttonagain.HoldandpresstheMENU

buttonaboutonesecondorwaitforoneminutetoexitthemenumode.



Reset

Select Reset, pressing ENTER button and all channels of the unit will return to their standard

position.

3.4HomePositionAdjustment

PressMENUbuttonintomenumode,thenpresstheENTERbuttonforabout3secondsintooffset

modetoadjustthehomeposition.SelectthefunctionbyENTERbutton.UseUPandDOWN

buttontochoosethesubmenu,presstheENTERbuttontostoreandautomaticallyreturntothe

lastmenu.

PressMENUbuttontoexit.



12B



PanOffset—panhomepositionadjustment

EnterOffsetMenu,SelectPanOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



TiltOffset—tilthomepositionadjustment

EnterOffsetMenu,SelectTiltOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



ColorOffset—colorhomepositionadjustment

EnterOffsetMenu,SelectColorOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



GoboOffset—gobohomepositionadjustment

EnterOffsetMenu,SelectGoboOffset,pressENTERbuttontoconfirm,thepresentpositionwill

13B

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



RGoboOffset—goborotationhomepositionadjustment

EnterOffsetMenu,SelectRGoboOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



PrismOffset—prismhomepositionadjustment

EnterOffsetMenu,SelectPrismOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom0to255,thenpressENTER

buttontostore.PressMENUbuttontoexit.



RPrismOffset—prismrotationhomepositionadjustment

EnterOffsetMenu,SelectRPrismOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom‐127to127,thenpressENTER

buttontostore.PressMENUbuttontoexit.



FocusOffset—focushomepositionadjustment

EnterOffsetMenu,SelectFocusOffset,pressENTERbuttontoconfirm,thepresentpositionwill

blinkonthedisplay,useUP/DOWNbuttontooffsetthevaluefrom0to255,thenpressENTER

buttontostore.PressMENUbuttontoexit.



14B

 4.ControlByUniversalDMXController 

4.1DMX512Connection



1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4 W 

resistor between pin 2(DMX‐) and pin 3(DMX+) into a 3‐pin XLR‐plug and plug it in the

DMX‐outputofthelastunit.

2. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the

input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very

high‐speedsignal.Inadequateordamagedcables,solderedjointsorcorrodedconnectorscan

easilydistortthesignalandshutdownthesystem.

3. The DMX output and input connectors are pass‐through to maintain the DMX circuit, when

powerisdisconnectedtotheunit.

4. Eachlightingunitneedstohaveanaddresssettoreceivethedatasentbythecontroller.The

addressnumberisbetween

0‐511(usually0&1areequalto1).

5. TheendoftheDMX512systemshouldbeterminatedtoreducesignalerrors.

6. 3pinXLRconnectorsaremorepopularthan5pinXLR.

3pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+)

5pinXLR:Pin1:GND,Pin2:Negativesignal(‐),Pin3:Positivesignal(+)

Pin4/5 : Notused.



15B

4.2DMXAddressSetting

IfyouuseauniversalDMXcontrollertocontroltheunits,youhavetosetDMXaddressfrom1to

512sothattheunitscanreceiveDMXsignal.

PressMENUbuttontoentermenumode,selectDMXAddress,pressENTERbuttontoconfirm,the

presentaddresswillblinkonthedisplay,useUPandDOWNbuttontoadjusttheaddressfrom0to

512,pressENTERbuttontostore.PressMENUbuttonbacktothelastmenuorlettheunitidle

oneminutetoexitmenumode.

PleaserefertothefollowingdiagramtoaddressyourDMX512channelforthefirst4units:

ChannelMode Unit1 Unit2 Unit3 Unit4

14channels 1 15 29 43

15channels 1 16 31 46



16B

4.3DMX512Configuration

14ChannelsMode:



17B

15ChannelsMode:



18B

 5.Troubleshooting

Followingareafewcommonproblemsthatmayoccurduringoperation.Herearesome

suggestionsforeasytroubleshooting:

A.Theunitdoesnotwork,nolightandthefandoesnotwork

1.Checktheconnectpowerandmainfuse.

2.Measurethemainsvoltageonthemainconnector.

3.CheckthepoweronLEDtoseeifitcanbelightupornot.

B.NotrespondingtoDMXcontroller

1.DMXLEDshouldbeon.Ifnot,checkDMXconnectors,cablestoseeiftheyarelinkedproperly.

2.IftheDMXLEDisonandnoresponsetothechannel,checktheaddresssettingsandDMX

polarity.

3.IfyouhaveintermittentDMXsignalproblems,checkthepinsonconnectorsoronPCBofthe

unitorthepreviousone.

4.TrytouseanotherDMXcontroller.

5.ChecktoseeiftheDMXcablesrunnearorrunalongsidetohighvoltagecablesthatmaycause

damageorinterferencetoDMXinterfacecircuit.

C.Oneofthechannelsisnotworkingwell

1.ThesteppermotormightbedamagedorthecableconnectedtothePCBisbroken.

2.Themotor’sdriveIConthePCBmightbeoutofcondition.

D.Thelampiscuttingoutintermittently

1.Thelampisnotworkingwell.Checkthemainsvoltageeithertoohighortoolow.

2.Internaltemperaturemaybetoohigh.Checkifreplacementoffanisneededonthehead.

E.Ifthepanbeltisbroken

1.Turnoffthemainspower.

2.Loosenthescrews(A)，openthecover(B).

3.Loosenthescrews(C).

4.Unplugalltheconnectwiresoverthebelt.

5.Changeanewbelt(D),putthebeltaroundtheaxisgearandmotorgear.

19B

6.Plugalltheconnectwire sbackuponthebelt.

7.Tightenallthescrews.



F.Ifthetiltbeltisbroken

1.Turnoffthemainspower.

2.Loosenallthescrews(A)andopentherightarmcover(B).

3.Loosenthescrews(C)thatfixthebridge.

4.Changeanewbelt(D).Pleaseadjustthetensionofthebeltproperly.



Note:donotfixthebelttootightasitiscaneasilyrupture.

Reversetheproceduresfromstep3to2.



Page is loading ...

ACME LED Move 600SE User manual

Brand: ACME

Model: LED Move 600SE

Category: Floodlights

Type: User manual

This manual is also suitable for

LED?MS600SE

Download PDF

report

ACME LED Move 600SE User manual

This manual is also suitable for

ACME LED Move 600SE User manual

Related papers

Other documents