Avaya Configuring RADIUS (308640-14.20 Rev 00) User manual

BayRS Version 14.20

Part No. 308640-14.20 Rev 00

January 2001

600 Technology Park Drive

Billerica, MA 01821-4130

Configuring RADIUS

ii

308640-14.20 Rev 00

The information in this document is subject to change without notice. The statements, configurations, technical data,

and recommendations in this document are believed to be accurate and reliable, but are presented without express or

implied warranty. Users must take full responsibility for their applications of any products specified in this document.

The information in this document is proprietary to Nortel Networks NA Inc.

The software described in this document is furnished under a license agreement and may only be used in accordance

with the terms of that license. The software license agreement is included in this document.

Trademarks

NORTEL NETWORKS is a trademark of Nortel Networks.

Bay Networks, ACE, AFN, AN, BCN, BLN, BN, BNX, CN, FRE, LN, Optivity, Optivity Policy Services, and PPX

are registered trademarks and Advanced Remote Node, ANH, ARN, ASN, BayRS, BaySecure, BayStack, BayStream,

BCC, BCNX, BLNX, Centillion, EtherSpeed, FN, IP AutoLearn, Passport, SN, SPEX, Switch Node, System 5000,

and TokenSpeed are trademarks of Nortel Networks.

Microsoft, MS, MS-DOS, Win32, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

All other trademarks and registered trademarks are the property of their respective owners.Restricted Rights Legend

Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subparagraph

(c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013.

Notwithstanding any other license agreement that may pertain to, or accompany the delivery of, this computer

software, the rights of the United States Government regarding its use, reproduction, and disclosure are as set forth in

the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Nortel Networks NA Inc. reserves

the right to make changes to the products described in this document without notice.

Nortel Networks NA Inc. does not assume any liability that may occur due to the use or application of the product(s)

or circuit layout(s) described herein.

rights reserved. Redistribution and use in source and binary forms of such portions are permitted, provided that the

above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising

materials, and other materials related to such distribution and use acknowledge that such portions of the software were

developed by the University of California, Berkeley. The name of the University may not be used to endorse or

promote products derived from such portions of the software without specific prior written permission.

SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

In addition, the program and information contained herein are licensed only pursuant to a license agreement that

contains restrictions on use and disclosure (that may incorporate by reference certain limitations and notices imposed

by third parties).

Nortel Networks NA Inc. Software License Agreement

NOTICE: Please carefully read this license agreement before copying or using the accompanying software or

installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement).

BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF

THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS

UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE. If you do not accept

308640-14.20 Rev 00

iii

these terms and conditions, return the product, unused and in the original shipping container, within 30 days of

purchase to obtain a credit for the full purchase price.

1. License grant. Nortel Networks NA Inc. (“Nortel Networks”) grants the end user of the Software (“Licensee”) a

personal, nonexclusive, nontransferable license: a) to use the Software either on a single computer or, if applicable, on

a single authorized device identified by host ID, for which it was originally acquired; b) to copy the Software solely

for backup purposes in support of authorized use of the Software; and c) to use and copy the associated user manual

solely in support of authorized use of the Software by Licensee. This license applies to the Software only and does not

extend to Nortel Networks Agent software or other Nortel Networks software products. Nortel Networks Agent

software or other Nortel Networks software products are licensed for use under the terms of the applicable Nortel

Networks NA Inc. Software License Agreement that accompanies such software and upon payment by the end user of

the applicable license fees for such software.

2. Restrictions on use; reservation of rights. The Software and user manuals are protected under copyright laws.

Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including

any revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with

any copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble,

use for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user

manuals or any copy, in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or

transfer the Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’

and its licensors’ confidential and proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise

disclose to any third party the Software, or any information about the operation, design, performance, or

implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors; however,

Licensee may grant permission to its consultants, subcontractors, and agents to use the Software at Licensee’s facility,

provided they have agreed to use the Software only in accordance with the terms of this license.

3. Limited warranty. Nortel Networks warrants each item of Software, as delivered by Nortel Networks and properly

installed and operated on Nortel Networks hardware or other equipment it is originally licensed for, to function

substantially as described in its accompanying user manual during its warranty period, which begins on the date

Software is first shipped to Licensee. If any item of Software fails to so function during its warranty period, as the sole

remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for the problem that may be

included in a future Software release. Nortel Networks further warrants to Licensee that the media on which the

Software is provided will be free from defects in materials and workmanship under normal use for a period of 90 days

from the date Software is first shipped to Licensee. Nortel Networks will replace defective media at no charge if it is

returned to Nortel Networks during the warranty period along with proof of the date of shipment. This warranty does

not apply if the media has been damaged as a result of accident, misuse, or abuse. The Licensee assumes all

responsibility for selection of the Software to achieve Licensee’s intended results and for the installation, use, and

results obtained from the Software. Nortel Networks does not warrant a) that the functions contained in the software

will meet the Licensee’s requirements, b) that the Software will operate in the hardware or software combinations that

the Licensee may select, c) that the operation of the Software will be uninterrupted or error free, or d) that all defects

in the operation of the Software will be corrected. Nortel Networks is not obligated to remedy any Software defect that

cannot be reproduced with the latest Software release. These warranties do not apply to the Software if it has been

(i) altered, except by Nortel Networks or in accordance with its instructions; (ii) used in conjunction with another

vendor’s product, resulting in the defect; or (iii) damaged by improper environment, abuse, misuse, accident, or

negligence. THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE

IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Licensee is responsible

for the security of its own data and information and for maintaining adequate procedures apart from the Software to

reconstruct lost or altered files, data, or programs.

4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS LICENSORS BE LIABLE FOR

ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR

PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN

IF NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT

iv

308640-14.20 Rev 00

SHALL THE LIABILITY OF NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT

EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE.

5. Government licensees. This provision applies to all Software and documentation acquired directly or indirectly by

or on behalf of the United States Government. The Software and documentation are commercial products, licensed on

the open market at market prices, and were developed entirely at private expense and without the use of any U.S.

Government funds. The license to the U.S. Government is granted only with restricted rights, and use, duplication, or

disclosure by the U.S. Government is subject to the restrictions set forth in subparagraph (c)(1) of the Commercial

Computer Software––Restricted Rights clause of FAR 52.227-19 and the limitations set out in this license for civilian

agencies, and subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause of DFARS

252.227-7013, for agencies of the Department of Defense or their successors, whichever is applicable.

6. Use of software in the European Community. This provision applies to all Software acquired for use within the

European Community. If Licensee uses the Software within a country in the European Community, the Software

Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the

examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such

intended examination of the Software and may procure support and assistance from Nortel Networks.

7. Term and termination. This license is effective until terminated; however, all of the restrictions with respect to

Nortel Networks’ copyright in the Software and user manuals will cease being effective at the date of expiration of the

Nortel Networks copyright; those restrictions relating to use and disclosure of Nortel Networks’ confidential

information shall continue in effect. Licensee may terminate this license at any time. The license will automatically

terminate if Licensee fails to comply with any of the terms and conditions of the license. Upon termination for any

reason, Licensee will immediately destroy or return to Nortel Networks the Software, user manuals, and all copies.

Nortel Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license.

8. Export and re-export. Licensee agrees not to export, directly or indirectly, the Software or related technical data or

information without first obtaining any required export licenses or other governmental approvals. Without limiting the

foregoing, Licensee, on behalf of itself and its subsidiaries and affiliates, agrees that it will not, without first obtaining

all export licenses and approvals required by the U.S. Government: (i) export, re-export, transfer, or divert any such

Software or technical data, or any direct product thereof, to any country to which such exports or re-exports are

restricted or embargoed under United States export control laws and regulations, or to any national or resident of such

restricted or embargoed countries; or (ii) provide the Software or related technical data or information to any military

end user or for any military end use, including the design, development, or production of any chemical, nuclear, or

biological weapons.

9. General. If any provision of this Agreement is held to be invalid or unenforceable by a court of competent

jurisdiction, the remainder of the provisions of this Agreement shall remain in full force and effect. This Agreement

will be governed by the laws of the state of California.

Should you have any questions concerning this Agreement, contact Nortel Networks, 4401 Great America Parkway,

P.O. Box 58185, Santa Clara, California 95054-8185.

LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT, UNDERSTANDS IT, AND

AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS. LICENSEE FURTHER AGREES THAT THIS

AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN NORTEL NETWORKS AND

LICENSEE, WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND

COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS

AGREEMENT. NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST

NORTEL NETWORKS UNLESS NORTEL NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT,

INCLUDING AN EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT.

308640-14.20 Rev 00

v

Contents

Preface

Before You Begin .............................................................................................................. xi

Text Conventions ..............................................................................................................xii

Acronyms .........................................................................................................................xiv

Hard-Copy Technical Manuals ......................................................................................... xv

How to Get Help .............................................................................................................. xv

Chapter 1

RADIUS Overview

How RADIUS Works .......................................................................................................1-2

Configuring RADIUS .......................................................................................................1-4

Nortel Networks RADIUS Implementation ......................................................................1-5

RADIUS Authentication ..................................................................................................1-6

Using SecurID for Radius Authentication .................................................................1-6

Using RADIUS with Multilevel Access to the Router ................................................1-7

Using IP and IPX Unnumbered Protocols for PPP Connections ..............................1-8

Using RADIUS with a Dial Service ...........................................................................1-8

Configuring Vendor-Specific Attributes (VSAs) for Authentication ...........................1-9

Using RADIUS with Demand Circuit Groups (Site Manager only) ...........................1-9

Configuring the Remote User to Work with the RADIUS Client .............................1-10

Using RADIUS with IP Utilities ...............................................................................1-10

RADIUS Accounting .....................................................................................................1-11

Using IP and IPX Unnumbered Protocols for PPP Connections ............................1-12

Using Dial VPN Services with Multilink PPP Accounting .......................................1-12

Using RADIUS with a Dial Service .........................................................................1-13

Using RADIUS with Demand Circuit Groups (Site Manager only) .........................1-13

Using RADIUS-Compatible Servers with the RADIUS Client .......................................1-13

Accepting a Remote User’s IP Address ........................................................................1-14

Configuring a RADIUS Client .......................................................................................1-14

vi

308640-14.20 Rev 00

For More Information ....................................................................................................1-15

Chapter 2

Starting RADIUS

Before You Begin ............................................................................................................2-2

Starting Configuration Tools ...........................................................................................2-2

Enabling RADIUS ...........................................................................................................2-3

Configuring Multiple RADIUS Clients .............................................................................2-8

Chapter 3

Customizing the RADIUS Client Configuration

Modifying the Client’s IP Address ...................................................................................3-1

Modifying the Authentication and Accounting Services .................................................3-3

Modifying the Protocol for RADIUS Authentication .........................................................3-5

Modifying the PPP Authentication Protocol ....................................................................3-6

Removing RADIUS Authentication and Accounting .......................................................3-7

Setting the Debug Message Level ..................................................................................3-8

Chapter 4

Customizing the RADIUS Server Configuration

Modifying the Primary Server’s Password ......................................................................4-2

Modifying the Server Mode .............................................................................................4-3

Designating Authentication and Accounting UDP Ports .................................................4-4

Modifying the Server Response Time ............................................................................4-6

Modifying the Number of Client Requests to the Server ................................................4-7

Configuring Alternate Servers ........................................................................................4-9

Reconnecting to the Primary Server ............................................................................4-11

Changing the Primary and Alternate Servers ...............................................................4-12

Removing a Server Entry .............................................................................................4-14

Appendix A

Site Manager Parameters

Client IP Address Parameter ......................................................................................... A-2

Server Configuration Parameters .................................................................................. A-3

Protocol Parameters for RADIUS Authentication ........................................................... A-7

308640-14.20 Rev 00

vii

Appendix B

Monitoring RADIUS Using the

BCC show Commands

Online Help for show Commands .................................................................................. B-2

show radius alerts .......................................................................................................... B-3

show radius clients ........................................................................................................ B-4

show radius servers general .......................................................................................... B-5

show radius servers timers ............................................................................................ B-6

show radius stats accounting ......................................................................................... B-7

show radius stats authentication .................................................................................... B-8

Appendix C

Configuration Examples

Configuring RADIUS Authentication .............................................................................. C-2

Configuring RADIUS Accounting ................................................................................... C-6

Configuring RADIUS Accounting and Authentication .................................................. C-12

Appendix D

Vendor-Specific Attributes

Nortel Networks Vendor-Specific Attributes ................................................................... D-2

RADIUS Dictionary File ................................................................................................. D-3

Appendix E

Configuring RADIUS with SecurID

Configuring RADIUS Client and ACE/Server Attributes

on the Router ................................................................................................................. E-2

Using the BCC ........................................................................................................ E-2

Using Site Manager ................................................................................................. E-4

Configure a RADIUS Client .............................................................................. E-5

Configure a RADIUS Server ............................................................................. E-6

Select a Protocol for RADIUS Authentication .................................................. E-7

Configuring the ACE/Server .......................................................................................... E-8

Establishing User Authentication ................................................................................... E-8

Logging In the First Time Using “New PIN” Mode ................................................... E-9

Logging In with a Valid PIN ................................................................................... E-10

“Next Tokencode” Prompt ...................................................................................... E-10

Index

308640-14.20 Rev 00

ix

Figures

Figure 1-1. Sample Network Using RADIUS ..............................................................1-3

Figure 2-1. BCC Hierarchy of Objects ........................................................................2-3

Figure 2-2. Configuration Manager Window ...............................................................2-3

Figure A-1. RADIUS Client Configuration Window .................................................... A-2

Figure A-2. RADIUS Server Configuration Window ................................................... A-3

Figure A-3. RADIUS Dial_In Protocol Window .......................................................... A-7

Figure C-1. Sample Network Using RADIUS Authentication ..................................... C-2

Figure C-2. Sample Network Using RADIUS Accounting .......................................... C-6

Figure C-3. Sample Network Configured for Dialing an Alternate Site .................... C-12

308640-14.20 Rev 00

xi

Preface

This guide describes Remote Authentication Dial-In User Service (RADIUS) and

what you do to start and customize RADIUS services on a Nortel Networks

™

router.

You can use the Bay Command Console (BCC

™

) or Site Manager to configure

RADIUS on a router. In this guide, you will find instructions for using both the

BCC and Site Manager.

Before You Begin

Before using this guide, you must complete the following procedures. For a new

router:

• Install the router (see the installation guide that came with your router).

• Connect the router to the network and create a pilot configuration file (see

Quick-Starting Routers, Configuring BayStack Remote Access, or Connecting

ASN Routers to a Network).

Make sure that you are running the latest version of Nortel Networks BayRS

™

and

Site Manager software. For information about upgrading BayRS and Site

Manager, see the upgrading guide for your version of BayRS.

Configuring RADIUS

xii

308640-14.20 Rev 00

Text Conventions

This guide uses the following text conventions:

angle brackets (< >) Indicate that you choose the text to enter based on the

description inside the brackets. Do not type the

brackets when entering the command.

Example: If the command syntax is:

ping <

ip_address

>

, you enter:

ping

192.32.10.12

bold text

Indicates command names and options and text that

you need to enter.

Example: Enter

show ip {alerts

|

routes}.

Example: Use the

dinfo

command.

braces ({}) Indicate required elements in syntax descriptions

where there is more than one option. You must choose

only one of the options. Do not type the braces when

entering the command.

Example: If the command syntax is:

show ip {alerts

|

routes}

, you must enter either:

show ip alerts

or

show ip routes

, but not both.

brackets ([ ]) Indicate optional elements in syntax descriptions. Do

not type the brackets when entering the command.

Example: If the command syntax is:

show ip interfaces [-alerts]

, you can enter either:

show ip interfaces

or

show ip interfaces -alerts

.

ellipsis points (. . . ) Indicate that you repeat the last element of the

command as needed.

Example: If the command syntax is:

ethernet/2/1 [<

parameter

>

<

value

>] . . .

, you enter

ethernet/2/1

and as many parameter-value pairs as

needed.

Preface

308640-14.20 Rev 00

xiii

italic text Indicates new terms, book titles, and variables in

command syntax descriptions. Where a variable is two

or more words, the words are connected by an

underscore.

Example: If the command syntax is:

show at <

valid_route

>

valid_route

is one variable and you substitute one value

for it.

screen text Indicates system output, for example, prompts and

system messages.

Example:

Set Trap Monitor Filters

separator ( > ) Shows menu paths.

Example: Protocols > IP identifies the IP option on the

Protocols menu.

vertical line (

|

) Separates choices for command keywords and

arguments. Enter only one of the choices. Do not type

the vertical line when entering the command.

Example: If the command syntax is:

show ip {alerts

|

routes}

, you enter either:

show ip alerts

or

show ip routes

, but not both.

Configuring RADIUS

xiv

308640-14.20 Rev 00

Acronyms

This guide uses the following acronyms:

CHAP Challenge Handshake Authentication Protocol

DVS Dial VPN Services

FTP File Transfer Protocol

HTTP Hypertext Transfer Protocol

IP Internet Protocol

IPX Internetwork Protocol Exchange

IPXWAN Internet Packet Exchange Wide Area Network

ISDN Integrated Services Digital Network

ISP Internet service provider

LAN local area network

LCD liquid crystal display

NTP Network Time Protocol

OSPF Open Shortest Path First

PAP Password Authentication Protocol

POTS Plain Old Telephone Service

PPP Point-to-Point Protocol

RADIUS Remote Authentication Dial-In User Service

RAS remote access server

RIP Routing Information Protocol

SAP Service Advertising Protocol

TCP/IP Transmission Control Protocol/Internet Protocol

UDP User Datagram Protocol

VPN virtual private network

VSA vendor-specific attribute

WAN wide area network

Preface

308640-14.20 Rev 00

xv

Hard-Copy Technical Manuals

You can print selected technical manuals and release notes free, directly from the

Internet. Go to the support.baynetworks.com/library/tpubs/ URL. Find the product

for which you need documentation. Then locate the specific category and model

or version for your hardware or software product. Use Adobe Acrobat Reader to

open the manuals and release notes, search for the sections you need, and print

them on most standard printers. Go to Adobe Systems at www.adobe.com to

download a free copy of Acrobat Reader.

You can purchase selected documentation sets, CDs, and technical publications

through the Internet at the www1.fatbrain.com/documentation/nortel/ URL.

How to Get Help

If you purchased a service contract for your Nortel Networks product from a

distributor or authorized reseller, contact the technical support staff for that

distributor or reseller for assistance.

If you purchased a Nortel Networks service program, contact one of the following

Nortel Networks Technical Solutions Centers:

An Express Routing Code (ERC) is available for many Nortel Networks products

and services. When you use an ERC, your call is routed to a technical support

person who specializes in supporting that product or service. To locate an ERC for

your product or service, go to the www12.nortelnetworks.com/ URL and click

ERC at the bottom of the page.

Technical Solutions Center Telephone

EMEA (33) (4) 92-966-968

North America (800) 2LANWAN or (800) 252-6926

Asia Pacific (61) (2) 9927-8800

China (800) 810-5000

308640-14.20 Rev 00

1-1

Chapter 1

RADIUS Overview

RADIUS (Remote Authentication Dial-In User Service) enables Internet service

providers (ISPs) to offer more remote access services to their customers. Remote

access is one of the fastest growing segments of the networking industry. Users in

branch offices, sales people in the field, and telecommuters are just a few of the

people who rely on remote access to do their jobs.

This chapter provides a conceptual overview of RADIUS, and explains how

Nortel Networks implements it. This chapter covers the following topics:

Topic Page

How RADIUS Works 1-2

Configuring RADIUS 1-4

Nortel Networks RADIUS Implementation 1-5

RADIUS Authentication 1-6

RADIUS Accounting 1-11

Using RADIUS-Compatible Servers with the RADIUS Client 1-13

Accepting a Remote User’s IP Address 1-14

Configuring a RADIUS Client 1-14

For More Information 1-15

Configuring RADIUS

1-2

308640-14.20 Rev 00

How RADIUS Works

As networks grow to accommodate more users, network security and billing

become more difficult to manage. RADIUS centralizes security and controls

billing services. RADIUS thus not only improves security but also adapts to the

ever-increasing volume and needs of remote users and service providers.

A RADIUS application has two components, the RADIUS server and the

RADIUS client.

The RADIUS server is a computer equipped with server software (for example, a

UNIX workstation) that is located at a central office or campus. It has

authentication and access information in a form that is compatible with the client.

A network can have one server for both authentication and accounting, or one

server for each service.

The RADIUS client can be a router or a remote access server that is equipped with

client software and that typically resides on the same local area network (LAN)

segment as the server. The client is the network access point between the remote

users and the server.

RADIUS authentication lets you identify remote users before you give them

access to a central network site. RADIUS accounting enables the server to collect

data during a remote user’s dial-in session with the client. The server can then

determine billing charges.

RADIUS Overview

308640-14.20 Rev 00

1-3

Figure 1-1 shows a sample network using RADIUS over a POTS (Plain Old

Telephone Service) line and an ISDN (Integrated Services Digital Network).

Figure 1-1. Sample Network Using RADIUS

RADIUS

server

RADIUS client

POTS

ISDN

Remote dial-in

user

Remote dial-in

user

CR0001A

MODEM

BLN

Configuring RADIUS

1-4

308640-14.20 Rev 00

Configuring RADIUS

To configure the RADIUS server and client, follow these steps:

1.

Install the RADIUS server files. These files load at server startup and enable

the server to recognize the vendor-specific RADIUS clients.

• For Nortel Networks servers, copy the bayrs.dct, vendor.ini, and

dictiona.dcm files from the distribution CD to the directory you define at

installation time (usually C:\RADIUS\Services). For more information,

see Appendix D, “Vendor-Specific Attributes

” and the BaySecure Access

Control Administration Guide for your platform (UNIX, NetWare, or

NT).

• For non-Nortel servers, use the bayrs.dct file shown in Appendix D

to

modify your existing RADIUS dictionary. Because the bayrs.dct file is in

the format of some popular RADIUS servers, you may be able to use it as

a direct replacement for the existing RADIUS dictionary. For more

information, refer to the vendor-specific server documentation.

2.

Configure the user-specific information in the RADIUS server database. For

more information, refer to the vendor-specific documentation.

3.

Configure the BayRS RADIUS client using either Site Manager or the BCC.

For more information, see Chapters 2 through 4.

a.

Define the RADIUS slots and services to be provided (authentication,

accounting, or both).

b.

Configure the primary and secondary RADIUS servers.

4.

Configure RADIUS-enabled applications (dial services, HTTP, FTP, NTP,

Telnet).

Page is loading ...

Avaya Configuring RADIUS (308640-14.20 Rev 00) User manual

Related papers

Other documents