Pelco MPTV1510 User manual

Brand: Pelco

Model: MPTV1510

Type: User manual

This manual is also suitable for

Boiler MPTV1510

Pelco MPTV1510 is a versatile controller for PTZ cameras, providing precise pan, tilt, and zoom control with variable speed options. Designed for 115 VDC pan and tilt units, it offers auto scan and zoom lens control, making it ideal for various applications like surveillance, security, and broadcasting. With its rugged construction and user-friendly interface, the MPTV1510 ensures reliable and efficient operation.

MPT1510DT and

MPTV1510 Series

Controllers

Installation/

Operation Manual

C565M-B (7/98)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120

OFF

MPTV1510PAZ

MANUAL

PAN

AUTO

TILT

SPEED

PAN

SPEED

LEFT

RIGHT

DOWN

ZOOM

TELE

WIDE

FOCUS

NEAR

FAR

IRIS

OPEN

SPEED

2 Pelco Manual C565M-B (7/98)

REVISION HISTORY

Manual # Date Comments

C565M 1/85 Original version (schematics only).

C565M-A 6/90 Added text.

C565M-B 7/98 Reformatted and added Model MPTV1510PZ.

Removed schematics.

LIST OF ILLUSTRATIONS

Figure Page

1 Output Connector Assembly Diagram ............................................... 7

2 Model MPTV1510PAZ Front Panel .................................................... 8

LIST OF TABLES

Table Page

A Output Connector Pin Assignments ................................................... 7

CONTENTS

Section Page

1.0 GENERAL .................................................................................................. 3

1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3

1.2 UNPACKING INSTRUCTIONS ..........................................................4

1.3 RECOMMENDED TOOLS ................................................................. 4

2.0 DESCRIPTION ..........................................................................................5

2.1 MODELS ............................................................................................ 5

3.0 INSTALLATION .......................................................................................... 6

3.1 OUTPUT CONNECTOR ASSEMBLY ................................................ 6

3.2 SYSTEM CONNECTIONS ................................................................ 6

4.0 OPERATION .............................................................................................. 8

5.0 TROUBLESHOOTING ............................................................................... 9

6.0 SPECIFICATIONS .................................................................................... 10

7.0 WARRANTY AND RETURN INFORMATION ........................................... 12

Pelco Manual C565M-B (7/98) 3

Please thoroughly familiarize yourself with the information

in this manual prior to installation and operation.

1.0 GENERAL

1.1 IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be

observed.

1. Installation and servicing should only be done by qualified service personnel

and conform to all local codes.

2. Only use replacement parts recommended by Pelco.

3. After replacement/repair of this unit’s electrical components, conduct a

resistance measurement between line and exposed parts to verify the

exposed parts have not been connected to line circuitry.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a

risk of electric shock is present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this

unit.

CAUTION:

RISK OF

ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION:

TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER. NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

4 Pelco Manual C565M-B (7/98)

1.2 UNPACKING INSTRUCTIONS

Unpack and inspect all parts carefully.

The following items are supplied:

1 MPT1510DT or MPTV1510 Series Controller

1 Installation/Operation Manual (C565M-B)

Be sure to save the shipping carton, boxes and inserts. They are the safest materi-

als in which to make future shipments.

If an item appears to have been damaged in shipment, replace it properly in its box

and contact the factory at 1-800-289-9100 or 1-559-292-1981 for a replacement.

(International customers fax 1-559-348-1120 for authorization and instructions.)

If an item needs to be returned to the factory for repair, consult the WARRANTY

AND RETURN section of this manual for instructions.

1.3 RECOMMENDED TOOLS

Pelco does not supply the basic tools needed for the installation process. The fol-

lowing tools are recommended.

Wire stripper

AMP style crimp tool

Pelco Manual C565M-B (7/98) 5

2.0 DESCRIPTION

The MPT1510DT or MPTV1510 Series Controllers provide all the necessary elec-

tronics to implement the features below for Pelco's PT1250DC heavy duty and

PT550P medium duty 115 VDC pan and tilt units.

• Pan and tilt control via a joystick

• Pan and tilt speed control (on some models)

• Auto scan (on some models)

• Zoom lens control (on some models)

• Desk top or rack mount options, depending on the model

The front panels on all models contain a power switch, pilot lamp, and a joystick.

The controls for the remaining features listed above are also located on the front

panel, depending upon the model. The rear panel provides the 120 VAC, 60 Hz

power cord and a 14-pin Amp hard-wired connector to interface with the pan and tilt

unit.

2.1 MODELS

MPT1510DT Desktop joystick control for 115 VDC pan and tilt units

MPTV1510DT Same as MPT1510DT except variable speed

MPTV1510CAZ Same as MPTV1510DT except auto scan and zoom lens

control

MPTV1510PZ Rack mount joystick with variable speed and zoom lens control

for 115 VDC pan and tilt units

MPTV1510PAZ Same as MPTV1510PZ except auto scan control

6 Pelco Manual C565M-B (7/98)

3.0 INSTALLATION

3.1 OUTPUT CONNECTOR ASSEMBLY

Assemble the connector parts according to the instructions below. Refer to Figure 1

during assembly. For best results use an AMP style crimper when making the wire-

to-pin connection.

1. Slide the connector clamp assembly over the conductor cable. If the diameter

of the conductor cable is such that the rubber boot will slide over it easily then

slide the rubber boot onto the conductor cable at this time. If not, discard the

rubber boot.

2. Prepare the wires from the conductor cable as follows. Refer to Detail A in

Figure 1.

a. Strip at least 1" from the cable jacket to expose the wires. You may need

to strip more from the cable jacket if you have more wires.

b. Strip 1/8" from each wire.

c. Using an AMP style crimper, crimp the wires and their insulation to the

connector pins.

3. Slide the connector pins into the appropriate holes in the connector body until

they snap into place. Refer to Table A for output connector pin assignments,

depending on model and options. Refer to Detail B in Figure 1 for the pin

arrangement.

4. Push the connector clamp assembly (with boot, if used) toward the connector

body. Screw the clamp assembly onto the connector body, being careful not to

disturb the wires.

5. To complete the assembly, attach the appropriate clamp with the screws pro-

vided and tighten.

3.2 SYSTEM CONNECTIONS

1. For the rack mount models, install the controller in an appropriate rack.

2. Connect the output cable to the pan and tilt unit and to the rear panel (OUT 1)

of the controller.

3. Connect the 120 VAC, 60 Hz power cord, on the rear panel, to a power recep-

tacle. Some models have an auxiliary AC OUTLET installed on the rear panel

for user convenience.

Pelco Manual C565M-B (7/98) 7

Table A. Output Connector Pin Assignments

Pin No. Function

1 Pan/tilt common

2 No connection

3 Pan left

4 Field supply

5 Tilt down

6 Tilt up

7 Pan right

8 Ground

9 No connection

10 Iris

11 Focus

12 Zoom

13 Lens common

14 No connection

Figure 1. Output Connector Assembly Diagram

1214

14-PIN

1/8"

FRONT VIEW

8 Pelco Manual C565M-B (7/98)

4.0 OPERATION

Refer to Figure 2.

1. Set the power switch to the ON position to activate the controller. The pilot

lamp will light when power is applied.

2. If your model has a PAN switch, set it in either the AUTO position to select

auto scan (pan) or the MANUAL position to use the joystick.

3. Operate the pan function by moving the joystick LEFT or RIGHT.

4. Operate the tilt function by moving the joystick UP or DOWN.

5. Adjust the TILT SPEED or PAN SPEED by rotating the respective knobs (on

some models). The clockwise direction increases speed and counterclock-

wise decreases speed. The PAN SPEED control can be used with the PAN

switch in either position.

6. On some models, the camera lens can be operated by three switches and one

lens speed control. The lens must have motorized zoom, focus, and iris capa-

bilities in order for these lens control functions to operate. The switches are

spring-loaded to the center or off position and control the following:

Switch function Up position Down position

ZOOM TELE WIDE

FOCUS NEAR FAR

IRIS OPEN CLOSE

The lens SPEED control will adjust the speed of all lens functions simulta-

neously, not individually. Rotating the knob in the clockwise direction increases

speed and counterclockwise decreases speed.

Figure 2. Model MPTV1510PAZ Front Panel

OFF

MPTV1510PAZ

MANUAL

PAN

AUTO

TILT

SPEED

PAN

SPEED

LEFT

RIGHT

DOWN

ZOOM

TELE

WIDE

FOCUS

NEAR

FAR

IRIS

OPEN

SPEED

Pelco Manual C565M-B (7/98) 9

5.0 TROUBLESHOOTING

If operating problems are experienced with the controller, check the fuses and the

power supply cord. Next, check the condition of the output cable and its two con-

nections.

There is nothing else that can be done without the aid of proper test equipment. It is

recommended that your dealer or the Pelco Customer Service Department be con-

tacted for assistance. Refer to Section 7.0 for warranty and return information.

10 Pelco Manual C565M-B (7/98)

6.0 SPECIFICATIONS

ELECTRICAL

Input Voltage: 120 VAC, 50/60 Hz

Maximum Power

Requirements: 250 vA

Power Cord: 3-wire grounded, #18 AWG

Fuse Protection:

Model F1 F2 F3

MPT1510DT 1 A N/A N/A

MPTV1510DT 2 A N/A N/A

MPTV1510CAZ 3 A 2 A 0.2 A Slow Blow

MPTV1510PZ 3 A 2 A 0.2 A Slow Blow

MPTV1510PAZ 3 A 2 A 0.2 A Slow Blow

Receptacles: 14-pin AMP CPC type

Auxiliary convenience outlet (on some models)

GENERAL

Construction

Cover: Steel, baked enamel finish (black leatherette)

Chassis: Steel, zinc plated

Panel: Aluminum, baked enamel finish (black with white silkscreen)

DIMENSIONS

Height Width Depth

MPT1510DT 1.8 (4.6) 5.5 (14.0) 8.9 (22.6)

MPTV1510DT 1.8 (4.6) 5.5 (14.0) 8.9 (22.6)

MPTV1510CAZ 1.8 (4.6) 19.0 (48.3) 10.2 (25.9)

MPTV1510PZ 1.8 (4.6) 19.0 (48.3) 10.2 (25.9)

MPTV1510PAZ 1.8 (4.6) 19.0 (48.3) 10.2 (25.9)

(Design and product specifications subject to change without notice.)

NOTE:

Values in parentheses are

centimeters; all others are inches.

Pelco Manual C565M-B (7/98) 11

NOTES

12 Pelco Manual C565M-B (7/98)

7.0 WARRANTY AND RETURN INFORMATION

Pelco, the Pelco logo, Camclosure, Esprit,

Genex, Legacy, and Spectra are registered

trademarks of Pelco.

Endura and ExSite are trademarks of Pelco.

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

Series products (multiplexers, server, and keyboard).

• Three years on Camclosure

and fixed camera models, except the CC3701H-2, CC3701H-2X,

CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-

year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed

dome products.

• Two years on Spectra

, Esprit

, ExSite

™

, and PS20 scanners, including when used in

continuous motion applications.

• Two years on Esprit

and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

™

Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications

(that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.

All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs

made necessary by reason of misuse, alteration, normal wear, or accident are not covered under

this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the

specific use or application made of the Products. Pelco’s liability for any claim, whether based on

breach of contract, negligence, infringement of any rights of any party or product liability, relating

to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event

will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss

of profit and claims of third parties) however caused, whether by the negligence of Pelco or

otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981

to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty

conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received

by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)

289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,

and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number

and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed

to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Pelco MPTV1510 User manual

Brand: Pelco

Model: MPTV1510

Type: User manual

This manual is also suitable for

Boiler MPTV1510

Download PDF

report

Pelco MPTV1510 User manual

This manual is also suitable for

Pelco MPTV1510 User manual

Related papers