Refer to Figures 1 and 2.
1. Locate the Transmitter next to or near
the door.
Do not mount the transmitter
on a metal surface.
2. Remove the Transmitter cover by
inserting the tip of a screwdriver in
the slot at the bottom of the Transmitter
and then gently rock the Transmitter
cover apart from the Transmitter base.
3. Choose a level place to locate the
Transmitter base.
4. Position the Transmitter base,
and mark the mounting surface with
a pencil through the two holes in
the Transmitter.
5. Drill two
3
⁄16" diameter holes at
the previously marked area.
6. Insert the plastic anchors into
the
3
⁄16" diameter holes.
7. Place Transmitter over anchors,
and fasten with two screws provided.
Do not replace cover at this time.
TRANSMITTER SOUND CODING
Refer to Figure 3.
1. The Transmitter can be coded to sound
one of three chime sounds.
2. Select the desired sound as illustrated
in Figure 3.
3. Position the plastic jumper straps
in the proper location for desired
chime sound.
TRANSMITTER SECURITY
CODING
Refer to Figure 3.
It is not necessary to change the
security code of the Transmitter unless
you experience interference from other
wireless devices.
1. To change the security code, remove
any combination of the six plastic
jumper straps.
2.
NOTE: Both the Transmitter and
Receiver codes must match.
BATTERY INSTALLATION
Refer to Figure 3.
1. Position the A23 12 volt battery
as illustrated. Be sure to observe
polarity (+/–). For replacement
battery, use EverReady
®
A23BP or
Duracell
®
MN21B (or equivalent).
INSTALLING TRANSMITTER
COVER
Refer to Figure 4.
1. Position the Transmitter cover over
the Transmitter base. The red light
must be lined up over the hole in the
Transmitter cover. Firmly press cover
over base.
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Wireless Chime
MODEL: LA-206WH
• For use with the LA-206TWH
FIGURE 1
FIGURE 2
TO OPEN COVER
“PUSH”
SCREW HOLE FOR WALL
MOUNTING
SCREW HOLE FOR WALL
MOUNTING
+
–
6
5
4
3
2
1
ONE NOTE
TWO NOTE
WESTMINSTER
SECURITY
CODE SETTING
FIGURE 3
SOUND SELECTION
12V “A23”
BATTERY
LED
Congratulations on your purchase of a NuTone Select-a-Tone chime. The chime
o
perates by a radio frequency signal transmitted by the pushbutton and received by the
c
hime. The pushbutton/transmitter is mounted at the door. The receiver may be located
a
nywhere in your home within 100 feet of the transmitter. The pushbutton/transmitter
can be programmed to sound one of three chime sounds. This feature allows up to
three transmitters to generate three different chime sounds.
FIGURE 4
MOUNTING THE PUSHBUTTON TRANSMITTER
REMOVING THE RECEIVER COVER
Refer to Figure 5.
1. Press the two locking tabs located
o
n the bottom of the Receiver cover,
and lift cover from base.
2. Set chime cover aside.
MOUNTING OF RECEIVER
Refer to Figure 6.
Receiver may be used as
a portable receiver or may
be wall mounted. Use the
f
ollowing procedure when
mounting the Receiver to
the wall.
1. Select the desired
mounting location. This
location should be at least 1
foot away from metal
objects and within 100 feet
of the chime transmitter.
2. Drill one
3
⁄
16
" hole at the desired mounting height.
3. Insert the plastic anchor into the
3
⁄
16
" hole.
4. Drive the upper screw into the plastic anchor until the head of
the screw extends approximately
1
⁄
8
" from the mounting surface.
5. Place the keyhole slot in the receiver base over the screw head.
Slide the Receiver down to secure it.
6. Level the chime receiver on the mounting surface.
7. Mark the mounting surface with a pencil at the center
of the oval hole in the bottom of the receiver base.
8. Gently remove the chime base from the mounting surface
and drill one
3
⁄
16
" hole at the previously marked area.
9. Insert the plastic anchor into the
3
⁄
1
6
" hole and remount
the chime receiver.
10. Insert the screw through the chime base into the plastic anchor.
Level chime base and tighten screw.
RECEIVER SECURITY CODING
Refer to Figure 7.
Changing the
Security code is not
necessary unless you
have changed the
security code
in the transmitter.
Both the transmitter
and receiver codes
must match.
1. Remove the
same jumpers in
the receiver as in
the transmitter.
INSTALLING BATTERIES IN RECEIVER
Refer to Figure 7.
Refer to Figure 7 for placement and polarity of batteries.
The NuTone wireless chime receiver requires four “D” size alkaline
batteries.
ADJUSTING THE RECEIVER VOLUME
Refer to Figure 7.
1. Slide power switch to the ON position.
2. Press Transmitter button. The red light
on the Transmitter will light.
3. Adjust volume control to desired sound level.
To increase volume, turn the control clockwise.
+
+
+
+
––
––
O
N OFF
V
OLUME
C
ONTROL
C
ODE
S
ETTING
SECURITY CODE
SETTING & VOLUME
6
5
4
3
2
1
FIGURE 5
CHIME
RECEIVER
POWER
SWITCH
4 – “D” SIZE
BATTERIES
1/8"
KEYHOLE
SLOT
“PUSH” TO OPEN
FIGURE 7
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in China, Rev. 9/06, Part No. 85766
TROUBLESHOOTING GUIDE
P
ROBLEM
1. Chime does not sound.
Check batteries and polarity.
Make sure receiver or transmitter
is not located on metal surface.
Check receiver and transmitter security
code.
These codes must match.
2. Chime changes tone. Check batteries in receiver.
3. Chime looses volume. Check batteries in receiver.
4. Chime is activated by another
wireless device.
Change the security code in the transmitter
and receiver. These codes must match.
5. When transmitter button is pressed,
the incorrect chime sound is heard.
Check the sound code jumpers
in the transmitter.
S
OLUTION
FIGURE 6
ATTACHING THE RECEIVER COVER
Position chime cover over chime base. Align locking tabs on bottom
of cover to bottom of chime receiver base. Firmly press chime cover onto
c
hime base.
PREPARING THE RECEIVER
One Year Limited Warranty
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that
such products will be free from defects in materials or workmanship for a period of one (1) year from
the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
During this one year period, NuTone will, at its option, repair or replace, without charge, any
product or part which is found to be defective under normal use and service. THIS WARRANTY
DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT,
ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not
cover (a) normal maintenance and service or (b) any products or parts which have been subject to
misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty
installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express
warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL
NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT
OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the
address stated below or telephone 1/800-543-8687, (b) give the model number and part
identification and (c) describe the nature of any defect in the product or part. At the time of
requesting warranty service, you must present evidence of the original purchase date.
Date of Installation Builder or Installer
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free 1-800-543-8687
Please be prepared to provide:
Product model number • Date and Proof of purchase • The nature of the difficulty
Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field
Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599.
Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive,
Mississauga, Ontario, Canada L5T 1H9.
Rev. 01/2005
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
