Genesis GBDS450 User manual

Page is loading ...

English

Belt/Disc Sander

Operator’s Manual GBDS450

BELT/DISC SANDER 4.5 AMP

Operator’s Manual

Speciﬁcations:

• Model:  GBDS450

• RatedVoltage: 120V~60HZ

• RatedInputPower: 4.5A

• BeltSpeed(noload): 2,000SFPM

• DiscSpeed(noload): 3,400RPM

• BeltSize:  4”x36”(100mmx914mm)

• DiscSize:  6”(150mm)

• TableSize:  8-7/8”x6-1/4”(225mmx160mm)

• TableTilt:  0°-45°

• BeltTilt:  0°-90°

Includes:Table,MiterGaugeandWrenches

 WARNING:To reduce the risk of injury, user must read and understand

this operator’s manual before operating this tool. Save this Manual for future

reference.

Toll-Free Help Line: 1-888-552-8665

WARNING:TheOperationofanypowertoolcanresultinforeign

objectsbeingthrownintoyoureyes,whichcanresultinsevereeyedamage.

Beforebeginningtooloperation,alwayswearsafetygogglesorsafetyglasses

withsideshieldsandafullfaceshieldwhenneeded.WerecommendWide

VisionSafetyMaskforuseovereyeglassesorstandardsafetyglasseswith

sideshields.AlwaysweareyeprotectionwhichismarkedtocomplywithANSI

Z87.1.

Look for this symbol to point out important safety

precautions. It means attention!!! Your safety is

involved.

GENERAL SAFETY RULES

 WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

• Leadfromlead-basedpaints,

• Crystallinesilicafrombricksandcementandothermasonryproducts,and

• Arsenicandchromiumfromchemicallytreatedlumber.

Your risk from these exposures varies, depending on how often you do this

type of work. To reduce your exposure to these chemicals: work in a well

ventilated area, and work with approved safety equipment, such as those

dust masks that are specially designed to ﬁlter out microscopic particles.

WEARYOUR

FORESIGHTISBETTER

THANNOSIGHT

SAFETYGLASSES

3

English

WARNING:READ AND UNDERSTAND ALL WARNINGS, CAUTIONS

AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure

to follow all instructions listed below may result in electric shock, ﬁre and/or

serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA SAFETY

• Keep your work area clean and well lit.Clutteredbenchesanddarkareasinvite

accidents.

• Do not operate power tools in explosive atmospheres,suchasinthe

presenceofammableliquids,gases,ordust.Powertoolscreatesparkswhichmayignitethedust

orfumes.

• Keep bystanders, children, and visitors away while operating a power

tool.Distractionscancauseyoutolosecontrol.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Nevermodifythepluginanyway.Donot

useanyadapterplugsinanyearthed(grounded)powertools.Doubleinsulatedtoolsareequipped

withapolarizedplug(onebladeiswiderthantheother).Thisplugwilltinapolarizedoutletonly

oneway.Iftheplugdoesnottfullyintheoutlet,reversetheplug.Ifitstilldoesnott,contact

aqualiedelectriciantoinstallapolarizedoutlet.Donotchangethepluginanyway.Double

insulationeliminatestheneedforthethreewiregroundedpowercordandgroundedpowersupply

system.

•Donotexposepowertoolstorainorwetconditions.Waterenteringapower

toolwillincreasetheriskofelectricshock.

•Avoidbodycontactwithearthedorgroundedsurfacessuchaspipes,

radiators, ranges and refrigerators. Thereisanincreasedriskofelectricshockif

yourbodyisgrounded.

•Donotabusethecord.Neverusethecordforcarrying,pullingorunpluggingthepower

tool.Keepcordawayfromheat,oil,sharpedgesormovingparts.Damagedcordsincreasetherisk

ofelectricshock.

•Whenoperatingapowertooloutside,useanextensioncordsuitable

for outdoor use. Thesecordsareratedforoutdooruseandreducetheriskofelectricshock.

•DonotuseAConlyratedtoolswithaDCpowersupply.Whilethetoolmay

appeartowork.TheelectricalcomponentsoftheACratedtoolarelikelytofailandrateahazardto

theoperator.

PERSONAL SAFETY

• Stay alert, watchwhatyouaredoingandusecommonsensewhenoperatingapowertool.

Donotusetoolwhiletiredorundertheinuenceofdrugs,alcohol,ormedication.Amomentof

inattentionwhileoperatingpowertoolsmayresultinseriouspersonalinjury.

•Usesafetyequipment.Alwaysweareyeprotection.Safetyequipmentsuchasdust

mask,non-skidsafetyshoes,hardhat,orhearingprotectionforappropriateconditionswillreduce

personalinjuries.

•Dressproperly.Donotwearlooseclothingorjewelry.Keepyourhair,clothingandgloves

awayfrommovingparts.Looseclothes,jewelryorlonghaircanbecaughtinmovingparts.Air

ventsmaycovermovingpartsandshouldbeavoided.

English

Belt/Disc Sander

Operator’s Manual GBDS450

•Avoidaccidentalstarting.Ensuretheswitchisintheoffpositionbeforepluggingin.

Carryingpowertoolswithyourngerontheswitchorplugginginpowertoolsthathavetheswitch

oninvitesaccidents.

•Removeanyadjustingkeysorwrenchesbeforeturningthepower

tool on. Awrenchorkeythatisleftattachedtoarotatingpartofthetoolmayresultinpersonal

injury.

•Donotoverreach.Maintainproperfootingandbalanceatalltimes.Lossofbalancecan

causeaninjuryinanunexpectedsituation.

•Ifdevicesareprovidedforconnectionofdustextractionand

collection facilities, ensure these are connected and properly used.

Useofthesedevicescanreducedustrelatedhazards.

•Donotusealadderorunstablesupport.Stablefootingonasolidsurfaceenables

bettercontrolofthetoolinunexpectedsituations.

•Keeptoolhandlesdry,cleanandfreefromoilandgrease.Slipperyhandles

cannotsafelycontrolthetool.

TOOL USE AND CARE

• Secure the work piece. Useclamporotherpracticalwaytoholdtheworkpiecetoa

stableplatform.Holdingtheworkpiecebyhandoragainstyourbodyisunstableandmayleadto

lossofcontrol.

•Donotforcethepowertool.Thetoolwillperformthejobbetterandsaferatthefeed

rateforwhichitisdesigned.Forcingthetoolcouldpossiblydamagethetoolandmayresultin

personalinjury.

•Usethecorrectpowertoolforthejob.Don’tforcethetoolorattachmenttodoa

jobforwhichitisnotdesigned.

•Donotuseatooliftheswitchdoesnotturnitonoroff.Anytoolthat

cannotbecontrolledwiththeswitchisdangerousandmustberepairedorreplacedbyan

authorizedservicecenter.

•Turnthepowertooloff,anddisconnecttheplugfromthepowersourceand/

orbatterypackfromthepowertoolbeforemakinganyadjustments,changingtheaccessories,or

storingthetools. Suchpreventivesafetymeasuresreducetheriskofanaccidentalstartupwhich

maycausepersonalinjury.

•Storeidletooloutofreachofchildrenandotherinexperienced

persons. Itisdangerousinthehandofuntrainedusers.

•Maintainpowertoolswithcare.Checkforproperalignmentandbindingofmoving

parts,components,andanyotherconditionsthatmayaffectthetool’soperation.Aguardorany

otherpartthatisdamagedmustbeproperlyrepairedorreplacedbyanauthorizedservicecenterto

avoidriskofpersonalinjury.

•Userecommendedaccessories.Usingaccessoriesandattachmentsnot

recommendedbythemanufacturerorintendedforuseonthistypetoolmaycausedamageto

thetoolorresultinpersonalinjurytotheuser.Consulttheoperator’smanualforrecommended

accessories.

•Keepcuttingtoolssharpandclean.Properlymaintainedcuttingtoolswithsharp

cuttingedgesarelesslikelytobindandareeasiertocontrol.

5

English

•Feedtheworkpieceinthecorrectdirectionandspeed.Feedthework

pieceintoablade,cutter,orabrasivesurfaceagainstthedirectionofthecuttingtool’sdirection

ofrotationonly.Incorrectlyfeedingtheworkpieceinthesamedirectionmaycausethework

piecetobethrownoutathighspeed.

•Neverleavethetoolrunningunattended,turnthepoweroff.Donot

leavethetooluntilitcomestoacompletestop.

•Neverstartthepowertoolwhenanyrotatingcomponentisin

contact with the work piece.

SERVICE

• Have your power tool serviced by a qualiﬁed repair person using

only identical replacement parts. Thiswillensurethatthesafetyofthepowertool

ismaintained.

•Serviceyourpowertoolperiodically.Whencleaningatool,becarefulnotto

disassembleanyportionofthetoolsinceinternalwiresmaybemisplacedorpinched.

WARNING:

READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING

INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all

instructions listed below may result in electric shock, ﬁre and/or serious

personal injury.

EXTENSION CORDS

Grounded tools require a three wire extension cord.Doubleinsulatedtoolscan

useeitheratwoorthreewireextensioncord.Asthedistancefromthepowersupplyoutletincreases,

youmustuseaheaviergaugeextensioncord.Usingextensioncordswithinadequatelysizedwire

causesaseriousdropinvoltage,resultinginlossofpowerandpossibletooldamage.Refertothe

tableshownbelowtodeterminetherequiredminimumwiresize.

Thesmallerthegaugenumberofthewire,thegreaterthecapacityofthecord.Forexample:a

14-gaugecordcancarryahighercurrentthana16-gaugecord.Whenusingmorethanoneextension

cordtomakeupthetotallength,besureeachcordcontainsatleasttheminimumwiresizerequired.

Ifyouareusingoneextensioncordformorethanonetool,addthenameplateamperesandusethe

sumtodeterminetherequiredminimumwiresize.

Guidelines for Using Extension Cords

• Ifyouareusinganextensioncordoutdoors,besureitismarkedwiththesufx“W-A”(“W”in

Canada)toindicatethatitisacceptableforoutdooruse.

• Besureyourextensioncordisproperlywiredandingoodelectricalcondition.Alwaysreplacea

damagedextensioncordorhaveitrepairedbyaqualiedpersonbeforeusingit.

• Protectyourextensioncordsfromsharpobjects,excessiveheat,anddamporwetareas.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate

Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

English

Belt/Disc Sander

Operator’s Manual GBDS450

SPECIFIC SAFETY RULES FOR BELT/DISC SANDERS

 WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT

(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT

SAFETY RULES. If you use this tool unsafely or incorrectly, you can suffer

serious personal injury!

•Makesurethebelt/discsanderisonarm,levelsurfaceand

properly secured toavoidinjuryfromunexpectedmovement.

• Unplug the tool before making adjustments, repairs, maintenance

or storing.

•Alwaysswitchoffthetoolbeforeunpluggingittoavoidaccidentalstarting

whenrepluggingthetoolintoapowersource.

•Weareyeprotectionanddustmask.

•Donotoperatethesanderuntilitisassembledandinstalledaccordingtothis

manual’sinstructions.

•Donotusethetooliftheswitchdoesnotturnitonandoff.Defectiveswitchesshouldbe

immediatelyreplacedbyanauthorizedservicecenterandthemachinenotusedunderrepairs

arecompleted.

•Alwayssupportworkpiecewithmitergauge,worksupportor

table.

•Keepngersawayfrompinchpointsbetweenhousingandsandingbeltordisc.

•Maintain1/16in.(1-2mm)clearancebetweentableandsandingbelt

or disc.

•Maintainproperadjustmentofsandingbelttensionandalignment.

•Neversandmorethanonepieceatatime.

•Alwaysfeedtheworkpiecefromlefttorightagainstthedirectionthesanding

beltisrotating.

•Useextracautionwithlarge,verysmallorawkwardworkpiece.Neverusethistool

tosandapiecetoosmalltoholdbyhand.

•Avoidawkwardoperationsandhandpositionswhereanunexpectedor

suddenslipthatcouldcauseyourhandorngerstomoveintothesandingbeltordisc.

•Neverstandinlinewiththepathofworkpiece.

•Donotoperateinrainorindamplocations.

•Groundingrequired.

SAVE THESE INSTRUCTIONS

1.ON/OFFSwitch

2.Table

3.MiterGauge

4.TableLockKnob

5.DiscGuard

6.SandingDisc

7.WorkSupport

8.SandingBelt

9.BeltBed

10.BeltTensionLever

11.BeltTrackingKnob

12.BeltBedLockScrew

13.DustPort

14.MountingHoles

15.Base

7

English

YOUR BELT/DISC SANDER

10

15

13

14

12

11

9

8

7

6

5

4

3

2

1

FIG 1

A  Belt/DiscSander 1 

B  TableAssembly 1

C  WorkSupport 1

D  TableLockKnob 1

E  MiterGauge 1

F Wrench  1

G  AllenKey  1

Operator'sManual(notshown)1



English

Belt/Disc Sander

Operator’s Manual GBDS450

UNPACKING AND CONTENT

IMPORTANT:Due to modern mass production techniques, it is

unlikely the tool is faulty or that a part is missing. If you ﬁnd anything

wrong, do not operate the tool until the parts have been replaced or the

fault has been rectiﬁed. Failure to do so could result in serious personal

injury.

Contents in Package: (FIG 2)

Item Description QTY Item Description QTY

WARNING: If any parts are missing or damaged, do not attempt to

assemble the tool, plug in power cord or turn the switch on until the missing or

damaged parts are replaced.

FIG 2

A

G

F

E

D

B

C

9

English

ASSEMBLY

WARNING: Always be sure that the tool is switched off and unplugged

from the power source before adjusting, adding accessories, or checking a

function on the tool

.

Installing or replacing Sanding Disc and

Guard (FIG 3)

One6"sandingdisc(3)andthedisc guard (1) are pre-

installedatthefactory.

To replace the sanding disc

1.Unplugthesanderfromthepowersource.

2. Using a Phillips screwdriver, loosen and remove two

screws(2)onthediscguard.

3.Removethediscguard.

4.Peelofftheoldsandingdisc.

5. Remove the backing from a new sanding disc. Align

perimeterofdiscwithsandingplateandrmlypressthe

discintoposition.

6.Reinstall the disc guard as shownon FIG 3.Thedisc

guardcanbeadjustedupand downtocoversanding

discformoreprotection.

Installing or Replacing Sanding Belt

(FIG 4, 5, 6)

Asandingbeltispre-installedandalignedatthefactory.

To replace the sanding belt

NOTE:Use 4"x36" (100mm x 914mm) sanding

belt. On the smooth side of the sanding belt,

there is a directional arrow. The sanding belt

must run in the direction of the arrow.

1.Unplugthesanderfromthepowersource.

2.PulltheBeltTensionLever(1)atdirectionshownonFIG

4toreleasebelttension.

3.Loosenandremovethescrew(3)oneachsideofbelt

bed(8).Removetheupperbeltguard(5).

4.Loosenandremovetwoscrews(4)oneachsideofbelt

bed(8).Removethelowerbeltguard(7).

5.Removetherubberbump(6).

6.Removetheoldsandingbelt(10)fromdriver(9)andidler

rollers(10).SeeFIG6.

7.Placeanewsandingbeltoverthedriverroller(9)and

idler roller (10) with the direction arrows running

counter-clockwise.Besurethesandingbeltiscentered

onbothrollers.

8.Putrubberbump,lowerbeltguardandupperbeltguard

backon.Tightenscrews(3,4)onbothsidesofthebelt

bed(8)tokeepguards(5,7)inplace.

9.Pushthebelttensionlever(1)backintolockingposition

toapplybelttension.

FIG 3

1

2

3

FIG 4

1

2

FIG 5

3

4

8

5

7

6

FIG 6

9

10

11

English

Belt/Disc Sander

Operator’s Manual GBDS450

 WARNING: The belt tension lever is

spring loaded. Be careful when pushing the

tension lever back into place to avoid personal

injury.

Installing Table Assembly

To Install the Table Assembly for Use with

Sanding Disc (FIG 7,8, 9)

1.Unplugthesanderfromthepowersource.

2.Insertthepositionpinontablesupportintotheupperhole

onthemachine.SeeFIG7.

3.Inserttablelockknob(1)throughaatwasherandthe

tablesupportslotandintothethreadedholeofbaseas

shownonFIG7.Turnandtightenthetablelockknob.

4.Loosenthethreehexheadnutsatbottomoftablesupport

(FIG9)andadjusttabletomakesurethetableedgeis

nomorethan1/16"(1-2mm)fromthesandingsurface.

Tightenthethreehexheadnuts.Re-tightenthelockknob.

 WARNING:To avoid trapping the work

piece or your ﬁnger between the table and

sanding disc, the table edge must be no more

than 1/16" (1-2mm) from the sanding surface.

To Install the Table Assembly for Use with

Sanding Belt (FIG 9, 10, 11)

1.Unplugthesanderfromthepowersource.

2.Removetheworksupportifitison.

3.Placethebeltbedintheverticalsandingposition.Referto

"PositioningtheBeltBed".

4.Insertthepositionpinontablesupportintotheposition

holeonthebeltbedasshownonFIG10.

5.Inserttablelockknobthroughaatwasherandthetable

supportslotandintothethreadedholeasshownonFIG

10.Turnandtightenthetablelockknob(1).

6.Loosenthethreehexheadnutsatbottomoftablesupport

andadjusttabletomakesurethetableedgeisnomore

than1/16"(1-2mm)fromthesandingsurface.Re-tighten

thelockknob.

7.Adjusttheprotectionplate(2)underthetabletocoverthe

exposedsandingbeltforextraprotection.

Installing Work Support (FIG 12)

1.Unplugthesanderfromthepowersource.

2.Placetheworksupport(1)overtheholeinthesideofthe

toolhousingasshowninFIG12.

3.Usingawrenchprovided,fastentheworksupportinplace

withthewasherandhexheadscrew(2).

FIG 8

FIG 9

FIG 10

1

FIG 7

1

FIG 11

2

11

English

Mounting Belt/Disc Sander

If during operation of the Belt/Disc Sander, there is any

tendencyfor thesanderto slideor "walk"orto tipover,

thenthesandermustbesecuredtoaworkbenchorother

supportingsurfaceusingfasteners(notsupplied)through

thetwoholesinthesanderbase.

ADJUSTMENTS

 WARNING: Always be sure that the tool

is switched off and unplugged from the power

source before adjusting, adding accessories,

or checking a function on the tool

.

Adjusting the Belt Tracking (FIG 13)

1.Plugthesanderintothepowersource.

2.Turnswitch‘ON’andimmediately‘OFF’,notingifthebelt

tendstoslideofftheidlerdrumordrivedrum.Ifitdidnot

tendtoslideoff,itisTRACKINGproperly.

3. If the sanding belt moves toward the disc, turn the

trackingknob(3)clockwise1/4turn.

4.Ifthesandingbeltmovesawayfromthedisc,turnthe

trackingknob(3)counterclockwise1/4turn.

5. Turn switch ‘ON and immediately ‘OFF’ noting belt

movement.Re-adjusttrackingknobifnecessary.

Positioning Belt Bed (FIG 14)

Thebeltbedlockscrew(4)locksthebeltbedinahorizontal

orverticalposition.

To adjust the belt bed position

1.Unplugthesanderfromthepowersource.

2.Loosenthelockscrew(4)usingAllenwrenchprovided.

3.Positionbeltbedandre-tightenthelockscrew(4).

OPERATION

 WARNING: Always be sure that the tool

is switched off and unplugged from the power

source before adjusting, adding accessories,

or checking a function on the tool

.

ON/OFF Switch (FIG 15)

1. To turn the sander ON,movetheswitch(1)to

the"ON"position.

2.To turn the sander OFF,movetheswitchtothe

"OFF"position.

3.To lock the switch in the OFF position,remove

thesafetykey(2)fromtheswitch.Storethekeyina

safeplace.

FIG 12

1

2

FIG 13

3

FIG 14

4

FIG 15

1

2

English

Belt/Disc Sander

Operator’s Manual GBDS450

WARNING: Always switch off the tool before unplugging it to avoid

accidental starting when re-plugging the tool into a power source.

Dust Port

Yoursanderhasa2-1/4"dustport(13-FIG1)locatedontheleftsideofthesander.Theportcanbe

connectedtoadustcollectionsystem.

Bevel Sanding (FIG 16)

Thetablecanbetiltedfrom0to45forbevelsanding.

To set table at bevel position

1.Loosenthetablelockknobandtiltthetabletothedesired

angle.

2.Retightenthetablelockknob.

Sanding Small End Surfaces Using the

Miter Gauge (FIG 16)

Amitergaugeisincludedwiththetool.Usingmitergaugeis

recommendedforsandingasmallpieceonthesandingdisc.

1.Resttheworkpieceagainsttheedgeofthemitergauge.

2.Alwaysmovethe workacrossthelefthandsideofthe

sandingdisc.

Surface Sanding on the Sanding Belt

(FIG 17)

Thesandingbeltcanbeusedeitherverticallyorhorizontally.

Dependingontheworkpiece,theworksupportcanbeused

eitherthehorizontalorverticalsandingoperation.Forsurface

sandingonthesandingbelt,usethehorizontalposition.

1. Hold the work piece rmly with both hands, keeping

ngersawayfromthesandingbelt.

2.Keeptheendbuttedagainsttheworkstopandmovethe

workevenly across the sanding belt.Useextracaution

whensandingaverythinpiece.

3.Applyonlyenoughpressuretoallowthesandingbeltto

removeasmallamountofmaterialatatime.

NOTE: Remove the work support when sanding

a long piece.

End Sanding on the Sanding Belt (FIG 18)

Forsandingtheendsoflongpiece,usethesandingbeltina

verticalposition.SeeFIG18

Usethetableinsteadofworksupport.

Usemitergaugeonthetableformoreaccuracy.

Sanding Curved Edges (FIG 19, 20)

Alwayssandtheinside curveonidlerdrumasshownin

FIG19

FIG 16

FIG 17

FIG 18

FIG 19

13

English

WARNING: Never attempt to sand the

ends of a work piece on the idler drums. It

could cause the work piece to ﬂy up and result

in personal injury.

Alwayssandingtheoutside curve onthelefthandside

ofthesandingdisc,asshowninFIG20

WARNING: Sanding the work piece on

the right side of the sanding disc could cause

the work piece to ﬂy up and result in personal

injury.

MAINTENANCE

CLEANING

Avoidusingsolventswhencleaningplasticparts.Mostplasticsaresusceptibletodamagefrom

varioustypesofcommercialsolventsandmaybedamagedbytheiruse.Usecleanclothstoremove

dirt,dust,oil,grease,etc.

WARNING: Do not at any time let brake ﬂuids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact with plastic parts.

Chemicals can damage, weaken or destroy plastic which may result in serious

personal injury.

Electrictoolsusedonberglassmaterial,wallboard,spacklingcompounds,orplasteraresubjectto

acceleratedwearandpossibleprematurefailurebecausetheberglasschipsandgroundingsare

highlyabrasivetobearings,brushes,commutators,etc.Consequently,wedonotrecommendusing

thistoolforextendedworkonthesetypesofmaterials.However,ifyoudoworkwithanyofthese

materials,itisextremelyimportanttocleanthetoolusingcompressedair.

LUBRICATION

Thistoolispermanentlylubricatedatthefactoryandrequiresnoadditionallubrication.

TWO-YEAR LIMITED WARRANTY

Thisproductiswarrantedfreefromdefectsinmaterialandworkmanshipfor2yearsafterdate

ofpurchase.Thislimitedwarrantydoesnotcovernormalwearandtearordamagefromneglect

oraccident.Theoriginalpurchaseriscoveredbythiswarrantyanditisnottransferable.Priorto

returningyourtooltostorelocationofpurchase,pleasecallourToll-FreeHelpLineforpossible

solutions.THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL

PURPOSES. ACCESSORIES INCLUDED ARE NOT COVERED BY THE 2 YEAR WARRANTY.

TOLL-FREE HELP LINE

ForquestionsaboutthisoranyotherGENESISProduct,

PleasecallToll-Free:888-552-8665.(Mon-Fri,9:00amto4:30pmEST.)

Orvisitourwebsite:www.richpowerinc.com

FIG 20

Page is loading ...

Richpower Industries, Inc.

736 Hampton Road

Williamston, SC USA

www.richpowerinc.com

Genesis GBDS450 User manual

Genesis GBDS450 User manual

in other languages

Other documents