Lightolier IS:LCAWTSX User manual

Brand: Lightolier

Model: IS:LCAWTSX

Type: User manual

Lightolier IS:LCAWTSX is a DMX Control Accent Lighting Colorspot Luminaire that can be installed on Lytespan track for ceiling installations. It features a LED (Light Emitting Diode) light source, requiring no maintenance. The luminaire is easy to install, with a simple 5-step process for one-circuit track installation and a 2-step process for double-circuit installation. For DMX control, simply connect a data cable into the DMX connector or insert an RJ45e jack connector.

CAUTION: Please read these instructions before installing the luminaire. To avoid electric shock, turn off the power from the electric panel before beginning. For safety, this

luminaire must be grounded. Consult an electrician to make sure all the requirements of the US or Canadian Code for electricity and the current local regulations comply. Keep these

instructions as reference.

IMPORTANT: Do not expose this luminaire to a room ambient temperature more

than 28°C. An overheating of this luminaire could reduce the performance and the

time life os the light-emitting diode (LED).

Note: This luminaire uses a LED (Light Emitting Diode) light source,

no maintenance is required.

A. ONE-CIRCUIT TRACK INSTALLATION:

1. Align adapter lever open on bead side. (Fig.2 & 3)

2. Align locking lever 60° counter-clockwise. (Fig.3)

3. Insert luminaire module into the track. (Fig.4)

4. Turn adapter lever clockwise. (Fig.4)

5. Turn locking lever 60°. (Fig.4)

B. DOUBLE-CIRCUIT INSTALLATION:

1. Lift brass contact tab approximately ¼ in. (7mm). (Fig.5)

2. Follow previous steps 1-5.

C. FOR DMX CONTROL:

1. Simply connect data cable shielded CAT5 recommended into DMX connector or

insert RJ45e jack connector. (Fig.6)

2. For daisy chain data connection, connect data cable CAT5 into data-in socket of

the ﬁrst luminaire, then connect the data cable to the data-out connector jack of

the next luminaire and so on. (Fig.7)

3. For signal termination, connect a DMX signal terminator to the data out of the

last luminaire in the network. (sold separately). (Fig.8)

Note: Hardware required for DMX control system. (not supplied)

Controller: DMX512 protocol.

Wiring: Use low-capacitance shielded twisted-pair stranded cables such as

EIA485 (RS485) or shielded CAT5.

- 24AWG: maximum run length of 300 m (1000 ft).

- 22AWG: maximum run length of 500 m (1600 ft).

Note: Using unshielded cable may create noise in the system and may cause

undesirable light output.

Connectors: RJ45e connector – 8 conductors (connections: T568B).

Installation Instructions for Lytespan Track LED DMX Control

Accent Lighting Colorspot Luminaire

BEAD

FIG.1

FIG.2

FIG.3

ADAPTER

LEVER

INTERLOCKING LEVER

TRACK

ADAPTER

LEVER

LUMINAIRE MODULE

TRACK

FIG.4

BRASS CONTACT

FIG.5

ADAPTER

LEVER

LOCKING LEVER

WARNING: This luminaire is for ceiling installation on Lytespan track only. Do not install on Monopoint, Multipoint, Fast Track, Sloped Ceiling Adapter, Extension Wand or ProSpec

Track.

FIG.6

FIG.7

FIG.8

DATA-IN SOCKET

RJ45e PLUG

DATA-OUT SOCKET

DMX TERMINATOR

Lightolier is a Philips group brand

IS:LCAWTSX

10-08/Rev-01

Canlyte 3015, Louis Amos, Lachine, Québec H8T 1C4 - Tel.: (514) 636-0670 - Fax.: (514) 636-0460 - www.canlyte.com