Marshall Air KK6 User manual

Brand: Marshall Air

Model: KK6

Type: User manual

This manual is also suitable for

KK6A
KK6B

Marshall Air KK6A is a multi-product holding unit with Lexan® doors on three sides and a digital display for precise temperature control, ideal for holding and serving food at optimal temperatures in various catering and foodservice establishments.

OWNER'S MANUAL

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

Supplier Name: MARSHALL AIR SYSTEMS, INC.

Address: 419 Peachtree Drive South

Charlotte, NC 28217

Serial #: __________________

Date Received: ______________ ___

Date Installed: __________________

Telephone #: 704-525-6230

Toll Free #: 800-722-3474 Customer Service

Fax #: 704-525-6229

Service Referral #: 800-722-3474

Local Service: ________________ _

Local Service #: __________________

MANUFACTURER'S INTRODUCTION

The Model KK6 Series Multi-Product Holding Unit

features Marshall's own ThermoGlo™ heating

technology. Heat radiates from every square inch of the

upper and lower flat plate heating surfaces. This

eliminates the need to clean intricate calrod, wire and

reflector assemblies. This unit is equipped with Lexan®

doors on three sides to prevent drafts and provide easy

access. A precision digital display and digital "set point"

temperature controller maintain consistent product

temperature.

GENERAL SPECIFICATIONS

Height: 15 1/2"

Width: 14 3/8"

Depth: 23 5/8"

Electrical: 110/120 volts AC 605 watts

60 Hz/6 amps

Power Cord: 6 ft. 3 wire grounding type UL

rating

Weight: 45 Ibs.

Note: Illumination with (2) 40 watt

food grade coated bulbs

Accessories: (1) Stacking kit (optional)

KK6A - W/(3) Pans, Lids &

Stack Unit

KK6B - W/(3) Pans, and

Stainless Steel Grates

Approvals: UL and NSF

Shipping Dimensions:

Height: 17 1/2"

Width: 16 1/4"

Depth: 25 3/4"

Weight: 54 Ibs.

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

TABLE OF CONTENTS

INSTALLATION............................................................................................................... 1

DAILY CHECKLIST AND CLEANING GUIDE............................................................ 1 -2

MONTHLY MAINTENANCE............................................................................................2

TROUBLESHOOTING CHART.......................................................................................3

REPLACEMENT PARTS LIST AND ILLUSTRATION..............................................…4-5

COMPLETE STACKING KIT P/N 110057......................................................................6

THERMOGLO™& HEATED HOLDING CABINET LIMITED WARRANTY................... 7

THERMOGLO™ & HEATED HOLDING CABINET WARRANTY RETURN

PROCEDURES............................................................................................................. 8

ILLUSTRATIONS

REPLACEMENT PARTS ILLUSTRATION.........................................FIGURE 1, PAGE 5

WIRING SCHEMATIC (KK6, KK6A, KK6B) 120V....................................... DWG 112620

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

INSTALLATION

PRE-INSTALLATION

The Multi-Product Holding Unit is packaged to minimize the risk of shipping damage. Immediately upon receipt,

make certain to inspect the unit for damage. FILE ALL CLAIMS WITH THE FREIGHT CARRIER.

FINAL INSTALLATION

1. Unpack unit and remove all protective paper or plastic covering from metal parts and Lexan® doors. NOTE: THE

SCREWS HOLDING THE LEXAN® DOORS ARE TO BE LOOSE TO ALLOW FOR HEAT EXPANSION.

2. Place holding unit on stable base. Make sure louvers at back of unit, next to power cord, are not blocked.

3. If unit is to be stacked, see Stacking Kit Installation Instructions, Page 5

4. Plug unit into an AC 120V receptacle.

DAILY CHECKLIST AND CLEANING GUIDE

TO USE THE MULTI-PRODUCT HOLDING UNIT

1. Turn on the power switch. The unit is ready to use after a 20-minute preheat period.

2. The temperature controller on the front of the unit is factory set for 175°F. With the control "ON", the

actual temperature is displayed. The range of set points available is from 140°F to 200°F.

CHANGING THE SET POINT

CAUTION: PRESS ONLY WITH SOFT PART OF FINGER - DO NOT PUSH WITH SHARP OBJECT.

FOR UNITS WITH SERIAL NO. 89021859 AND HIGHER:

The faceplate of the control is either black or gray. The set point may be verified or changed as follows:

IF BLACK: depress the set button to view the set point. To change set point, use Up/Down arrow to select new

set point while holding set button down.

IF GRAY: depress the set button and RELEASE to view set point. To change set point, push "set" and within

three seconds, use Up/Down arrow to select new set point.

FOR UNITS WITH SERIAL NO. 89021858 AND LOWER:

The "set point" can be checked by depressing the set button on the controller. The setting is adjustable and

may be changed by turning the small screw on the face of the controller while holding the red button down.

When the button is released the actual temperature is displayed.

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

3. If pans are to be used, place them in unit.

4. Wait one hour to stabilize the temperature.

5. Check the surface temperature on the unit digital display to see if it is 175°F ± 10°F.

6. If the digital display temperature is outside of the specified range, remove the pans, wait two

minutes, then check the actual surface temperature 6" from the front in the center. This should be

185°F ± 10°F. Note that the surface temperature is higher when the pans are removed.

CLEANING CHECKLIST

1. Turn off the unit and allow it to cool for 20 minutes.

2. Pans, lids and wire grates should be removed, washed in mild multi-purpose detergent, rinsed and

sanitized.

3. Clean unit and base with a damp cloth or non-abrasive cleaner. DO NOT IMMERSE UNIT IN

WATER! DO NOT USE CAUSTIC CLEANING SOLUTIONS!

4. Allow sufficient drying time before attempting to use.

MONTHLY MAINTENANCE

1. Follow the daily cleaning checklist; there are no periodic adjustments.

2. Check the condition of the two light bulbs located under the top cover. If these fail, do the following:

A. Unplug the unit.

B. Remove the bulb(s) by carefully unscrewing them from their sockets.

C. Replace the bulb(s) with a manufacturer's approved replacement part. (See parts list page 4.)

3. Check airflow through unit by feeling air at louvers on back of unit or checking for air draw at slots on

front on each side of temperature controller. If no movement felt, cooling fan is not working. Call a

qualified service technician to make repair.

4. Observe condition of Lexan® side panels. If excessively scratched and/or cracked, replace.

5. Inspect condition of cord/plug. If damaged, have it replaced.

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

TROUBLE SHOOTING CHART

** DISASSEMBLING HEATER VOIDS WARRANTY **

Identify problem in the left-hand column and look for probable cause and solution in right-hand column. Probable

causes listed in the order they are most likely to happen. This sequence should be used to isolate the problem.

PROBLEM PROBABLE CAUSE SOLUTION

1. No Light/No Heat Unplugged Circuit breaker is tripped

Plug in Reset breaker - call

electrician if tripped twice

Cord/plug defective Replace cord/plug

2. No Light/With Heat Light bulbs burned out Unplug unit and replace bulbs

3. Light/No Heat Defective heating unit assembly Replace heating unit assembly

4. No Heat at Base Defective wiring/temperature controller

Replace Wiring/temperature

controller

5. Low Product Temperature Set point too low Excessive air draft Reset to 175°F Move unit

6. Heat at Base too High Defective temperature controller

Replace defective temperature

controller

7. Heat at Base too Low

Defective sensor, temperature controller

or heating element

Replace sensor, temperature

controller or heating element

8. Display reads "EEE" Disconnected or defective sensor Reconnect or replace sensor

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

REPLACEMENT PARTS LIST (See Figure 1 for Diagram)

ITEM PART# DESCRIPTION

1 501867 Rubber Feet

2 114542 Temperature Controller *See Note)

3 502248 Transformer 120V to 12V

4 501864 Rocker Switch

5 110042 Fan

501882

501957

Lower Heating Element 120V

Lower Heating Element 220V

7 502169 Sensor

8 111894 Bumper Pin Replacement Set (see Page 6)

9 109872 ThermoGlo™

10 501865 Lampholder

11 502239 Coated Bulb

119892

109797

Optional Right Lexan® Side Panel With Stiffener Angle (KK6C Model)

Lexan® Side Panel (no stiffener angle)

13 501069 Hinge

119893

109798

Optional Lexan® Rear Panel With Stiffener Angle (KK6C Model)

Lexan® Rear Panel (no stiffener angle)

15 501193 Cord Strain Relief

16 109868 6 Ft. Cord w/Plug

17 109845 Lexan® panel, front (Optional)

18 501930 Hinge screws, 10-32 x 1/2"

19 501355 Nut 10-32

120918

109797

Optional Left Lexan® Side Panel With Stiffener Angle (KK6C Model)

Lexan® Side Panel (no stiffener angle)

21 109782 Platen Surface

22 117038 Temperature Controller Conversion (See Note Below)

Not Shown 503413 Kit, Temp. Control Faceplate REF:132574 Centigrade to Fahrenheit

• Note: If Temperature Controller Face looks like controller "A", order #114542. (See Figure 1)

If Temperature Controller Face looks like controller "B", order #117038. (See Figure 1)

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

REPLACEMENT PARTS ILLUSTRATION

110047KK6 RV082799

FIGURE

REPLACEMENT

PARTS

ILLUSTRATION

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

STACKING KIT INSTALLATION INSTRUCTIONS

1. When mounting units, be sure the rubber feet of the top unit are securely placed in the notches on the

brackets.

2. After stacking the two units, remove the two screws located on the rear side.

3. Mount the cord clamps and route the cord along the rear leg, as shown.

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

THERMOGLO™ AND HEATED HOLDING CABINET LIMITED WARRANTY

MARSHALL AIR SYSTEMS, INC., ("Marshall") warrants to the first purchaser ("Purchaser") all new equipment of its manufacture to be

free of defects in material and factory workmanship for a period of one year from date of shipment provided that (i) the equipment is installed

in the Continental United States, Canada or Hawaii and operated according to the Owner's Manual while located at the original address of

installation, (ii) the warranty registration card has been completed and returned to the factory within fifteen (15) days after installation.

Marshall's obligation under this warranty is limited to the repair or replacement at its option of any defective part. It is understood that

Marshall's obligation with respect to equipment located outside the Continental United States, Canada or Hawaii is limited to replacement

parts only.

Because Marshall does not and cannot control Purchaser's installation, use, and maintenance of equipment manufactured by Marshall,

this warranty DOES NOT COVER:

1. Any equipment calibration.

2. Switches.

3. Plugs and cords.

4. Blown fuses or bulbs.

5. Any component disassembled in the field or that has broken seals.

6. Any replacement parts used on the equipment which are not purchased from Marshall.

7. Accessory components not installed and/or manufactured by Marshall.

8. Water or grease accumulation, which will cause electrical failures.

9. Labor, except that provided at Marshall's factory.

10. Damage due to improper or lack of cleaning, abuse and/or service.

SHIPPING DAMAGE must be reported to the carrier and is not covered under this warranty. Marshall will not be liable for damage as a

result of improper installation, misuse, abuse, alteration of original design, incorrect voltage, unauthorized service, breakage of fragile items,

or any other damage caused by an act out of Marshall's control.

The effect of corrosion, fire, and normal wear on the equipment or component parts is not covered by this warranty. This warranty does

not cover cooking performance, smoke capture or holding temperatures which is a function of food types, textures, temperatures, equipment

line ups and other variables chosen by the Purchaser and over which Marshall has no control. This warranty does not apply to damage

caused by accident or to damage caused by the negligence of Purchaser or the employees of Purchaser or to damage caused by lightning

generated electrical current or any other Act of God whatsoever. This warranty does not apply to any equipment bearing a serial number

which has been tampered with or altered. Marshall reserves the right to accept or reject any such claim in whole or in part. Marshall will not

accept the return of any product without prior written approval from Marshall, and all such approved returns shall be made at Purchaser's

sole expense.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTY OF

MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OR PATENT OR OTHER

INTELLECTUAL PROPERTY RIGHT INFRINGEMENT, AND EXCEPT FOR THE EXPRESS WARRANTY CONTAINED HEREIN, THE

EQUIPMENT IS SOLD "AS IS." REMEDIES UNDER THIS WARRANTY AND UNDER ANY WARRANTY THAT MAY SURVIVE THE

DISCLAIMER OF WARRANTIES ARE LIMITED EXCLUSIVELY TO THOSE REMEDIES DESCRIBED ABOVE. NO OTHER REMEDY IS

AVAILABLE UNDER THIS WARRANTY OR ANY OTHER WARRANTY. NEITHER THIS WARRANTY NOR ANY OTHER WARRANTY

COVERS, AND MARSHALL WILL NOT BE RESPONSIBLE FOR, ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING

BUT NOT LIMITED TO THE COST OF DISASSEMBLY AND SHIPMENT OF THE EQUIPMENT, PRODUCTION OR PRODUCT LOSSES,

INJURY TO OTHER PROPERTY, OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR

FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS, OR

OTHER LOSSES. WHERE, DUE TO OPERATION OF LAW, CONSEQUENTIAL AND INCIDENTAL DAMAGES CANNOT BE

EXCLUDED, THEY ARE EXPRESSLY LIMITED IN AMOUNT TO THE PURCHASE PRICE OF THE EQUIPMENT.

FOR INTERNATIONAL INSTALLATIONS - PLEASE CONTACT YOUR LOCAL MARSHALL AIR

SYSTEMS RECOGNIZED DISTRIBUTOR.

110047KK6 RV082799

MODEL KK6 - MULTI-PRODUCT HOLDING UNIT

THERMOGLO™AND HEATED HOLDING CABINET WARRANTY

RETURN PROCEDURES

I. RETURN GOODS AUTHORIZATION FOR PARTS:

For prompt warranty parts replacement and RGA processing, please call Marshall's Customer

Service Department at 800-722-3474 or 704-525-6230 for assistance. In all cases, a Return Goods

Authorization (RGA) number must be issued by Marshall Air Systems, Inc. Unauthorized returns will

not be processed.

Option #1: Purchaser to return part(s) prepaid to Factory, Marshall to repair or replace at own

expense if defective, and ship part(s) back to Purchaser prepaid.

Option #2: Marshall to furnish replacement part(s) freight prepaid with or without requesting

return of the defective part(s).

Option #3: Purchaser may obtain replacement part(s) from recognized service agency.

II. NON-WARRANTY RETURNS:

All items returned for customer cancellations are subject to a 20% restocking fee. In the event of an

error by Marshall Air Systems, Inc., a Returned Goods Authorization will be issued for full credit.

Custom fabricated parts are not returnable.

FOR INTERNATIONAL INSTALLATIONS -- PLEASE CONTACT YOUR LOCAL

MARSHALL AIR SYSTEMS RECOGNIZED DISTRIBUTOR.

110047KK6 RV082799

Marshall Air KK6 User manual

Brand: Marshall Air

Model: KK6

Type: User manual

This manual is also suitable for

KK6A
KK6B

Download PDF

report

Marshall Air KK6 User manual

This manual is also suitable for

Marshall Air KK6 User manual

Related papers

Other documents