KitchenAid KUDD01SS User manual

Brand: KitchenAid

Model: KUDD01SS

Category: Dishwashers

Type: User manual

KitchenAid KUDD01SS is a single drawer dishwasher that can accommodate up to 104 lbs. It requires a 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply and a hot water line with 4.3-145 psi water pressure. The minimum water temperature should be 120°F (49°C). Installation requires a cabinet cutout that is level and will hold weight up to 104lbs. (47kg), and is in an area suitable for its size and use. Please refer to the Installation Instructions packed with the product for complete details.

PRODUCT MODEL SERIES OVERALL DIMENSIONS

CABINET DIMENSIONS

KUDD01SS

Electrical: 120-volt, 60 Hz, AC-only, 15 or

20 amp fused electrical supply is required. A

time-delay fuse or circuit breaker and separate

circuit is recommended.

Water: A hot water line with 4.3-145 psi

(30-1000 kPa) water pressure. Water temperature

must be minimum 120°F (49°C) at dishwasher. An

easily accessible valve with ³⁄₈” compression

fitting must be installed in the hot water supply

line.

Because Whirlpool Corporation policy includes a continuous commitment to improve our

products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. 8573714

02-03-06

Single Drawer Dishwasher

23⁷⁄₁₆"

(59.5 cm)

22⁷⁄₁₆" *

(57 cm)

16³⁄₃₂"

side

attaching

tabs

¹⁵⁄₃₂"

(52 cm)

drawer open

(10 cm)

moisture protection

tape

support surface must

be solid and level

Utility hole:

¹⁄₂" (3.8 cm) dia.

hole, either side –

immediately adjacent

to corner.

22⁷⁄₈" (58.0 cm)

¹³⁄₁₆

(9.7 cm)

⁷⁄₈

(50.5 cm)

⁵⁄₈

(6.7 cm)

23⁵⁄₈"* (60.0 cm)

16 ⁷⁄₃₂"

(41.2 cm)

These marks indicate the mounting tab screw locations.

Minimum thickness of cabinet/cavity sides – ⁵⁄₈" (1.6 cm)

* If custom wood panels are to be used, the product depth is specified

with an ¹¹⁄₁₆" (18 mm) door panel thickness.

NOTE: Product shown with front panels for dimension purposes.

Install the dishwasher in a cabinet cutout that is level, will hold weight

up to 104lbs. (47kg), and is in an area suitable for its size and use.

KitchenAid

Single Drawer Dishwasher Custom Cabinet Requirements

⁄16”

(9.7 cm)

⁄8”

(50.5 cm)

⁄8” (60.0 cm)

⁄2” (3.8 cm) dia.

either side immediately

adjacent to corner

Utility Hole:

⁄32”

(41.2 cm)

⁄8”

(6.7 cm)

⁄8 ”

(58.0 cm)

IMPORTANT: For best results, carefully read the following

instructions and recommendations before building the

custom cabinet.

• Build the custom cabinet to the size and speciﬁcations as

shown (See ﬁgure 2).

• The minimum thickness of cabinet/cavity sides is

⁄8” (1.6 cm).

• The supporting base of the cabinet must be solid, level,

and able to sustain weight up to 104 lbs. (47 kg).

• For best installation, the use of all four Side Attaching Tabs is

recommended. Wood spacers may need to be added to the

sides of the cabinet in order to properly secure the dishwasher

to the cabinet.

• A utility hole, that will be used to route power supply cord

and hoses, must be located as shown (See ﬁgure 2). The

utility hole can be located on either side depending on the

location of services. If the utility hole is not located as shown,

the hoses will prevent the dishwasher from being pushed

back all the way into the cavity. Make sure the edges of the

utility hole are smooth or covered to prevent damage to the

power cord and hoses. If the utility hole is through a metal

cabinet, the hole must be protected with an edge protector.

NOTE: Diamond

symbol indicates

Side Attaching Tab

screw locations.

• A 3-prong grounded outlet must be installed within

6” (15.2 cm) to 18” (45.7 cm) to either side of the utility hole

in the cabinet sidewall. The power outlet must be accessible

after installation.

• When installing a custom wood front door panel to the

dishwasher, the cabinet width of 23

⁄8” (60.0 cm) must be

increased to allow

⁄32” (2.5 mm) clearance between the

cabinet side and custom panel edge (See ﬁgure 2).

• For corner installation, there must be a

⁄2” (12.7 mm) space

between the adjacent cabinet doors (i.e. door knobs) and

open dishwasher drawer.

FIGURE 2

The minimum thickness of cabinet

cavity sides and bottom is

⁄8” (1.6 cm)

Adjacent cabinetry must not

extend above the cavity base.

DISHWASHER

• It is recommended that wood cabinetry surrounding

the dishwasher be sealed with an oil-based paint or

moisture-proof polyurethane to prevent possible

damage from humidity.

•

Refer to the Installation Instructions Single Drawer

Dishwasher included with the Drawer Dishwasher

to complete installation.

⁄8”

(39.7 cm)

⁄16”

(59.5 cm)

CUSTOM

PANEL

(Front Side)

FIGURE 1

9”

(22.9 cm)

⁄16”

(5.9 cm)

5”

(12.7 cm)

Medallion

Location Area

3) On the front side of the custom door panel, measure,

mark and cut a hole for the medallion to size as shown

(See ﬁgures 1 & 2).

NOTE: The medallion must be placed within the speciﬁed

medallion area. Do not locate outside of this speciﬁed area

(See ﬁgure 1)

4) Lay the custom door panel face down on a protective surface

to prevent damage or abrasions.

5) On the backside of the custom door panel, rout a

⁄4” (6.4 mm) radius around the medallion cutout previously

cut in step #3. The medallion end does not need to

be routed.

6) If custom door panel material is not suitable to withstand

damp conditions, seal with a moisture resistant material.

For painted panel, paint all rear edges to improve sealing.

7) On the backside of the custom door panel, measure and

mark the vertical center line and horizontal position line

(See ﬁgure 3).

NOTE: The 1

⁄16” (36.5 mm) horizontal position line is

marked for later use in the installation process. Refer to the

Installation Instructions Single Drawer Dishwasher included

with the Drawer Dishwasher to align and attach the custom

door panel to the factory supplied metal plate.

8) Mount the customer supplied handle to the location

previously marked on the custom panel.

IMPORTANT: When mounting the customer supplied

handle, screws must ﬁt ﬂush to the panel and not extend

beyond the back surface.

9) Refer to the

Installation Instructions Single Drawer

Dishwasher included with the Drawer Dishwasher

to complete installation.

⁄32” (32.6mm) MAX.

⁄32”

(30.8 mm)

⁄4”

(6.4 mm)

⁄64”

(30.6 mm)

⁄32”

(60.8 mm)

MEDALLION CUTOUT DIMENSIONS

Medallion

End

FIGURE 2

⁄16”

(36.5 mm)

Vertical

Center Line

Medallion

Location Area

FIGURE 3

Horizontal

Position Line

IMPORTANT: It is recommended that the custom door panel

be made from suitable material to withstand damp conditions

or adequately sealed with a moisture-resistant material to

withstand moisture and humidity.

1) Cut the custom door panel to size as shown

(See ﬁgure 1). The custom panel may be wider than

the dishwasher in order to match the surrounding cabinets.

NOTE: The minimum custom panel thickness is

⁄8” (16mm). Panel thickness more than

⁄16” (18mm)

can be accommodated but overall product depth will

increase accordingly.

2) On the front side of the custom door panel, measure and mark

the location of the customer supplied handle. The location is

customer preference. Do not install handle at this time.

CUSTOM

PANEL

(Back Side)

Center of

Custom Panel

KitchenAid

Single Drawer Dishwasher Custom Door Panel Requirements

MODEL: KUDD01SSPA

KitchenAid KUDD01SS User manual

Brand: KitchenAid

Model: KUDD01SS

Category: Dishwashers

Type: User manual

Download PDF

report

KitchenAid KUDD01SS User manual

KitchenAid KUDD01SS User manual

Related papers

Other documents