Brennenstuhl 1171250101 Datasheet

Page is loading ...

2

1

2

3

5-10 mm

L N

5-10 mm

L N

BA_Chip_Leuchte_Stationaer_130701.indd 2 01.07.13 10:56

Page is loading ...

8

D

Operating Instructions

Chip LED Light

Please note: Please read these instructions carefully prior to mounting

the light and store them in a safe location afterwards!

SPECIFICATIONS

Protection class: I

Nominal voltage: 220 – 240V~ 50Hz

Model: Output: Type of Motion Protective cover

protec- detector: dimensions:

tion:

L CN 110 IP65 10W (1 x 10W) IP65 no 110.5 x 83 x 4mm

L CN 110 PIR IP44 10W (1 x 10W) IP44 yes 110.5 x 83 x 4mm

L CN 130 IP65 30W (1 x 30W) IP65 no 220.5 x 180.5 x 4mm

L CN 130 PIR IP44 30W (1 x 30W) IP44 yes 220.5 x 180.5 x 4mm

L CN 150 IP65 50W (1 x 50W) IP65 no 281.5 x 231 x 4mm

L CN 150 PIR IP44 50W (1 x 50W) IP44 yes 281.5 x 231 x 4mm

L CN 180 IP65 80W (1 x 80W) IP65 no 303.5 x 225.5 x 5mm

The heavy-duty LED light is suitable for indoor and outdoor lighting

applications and is designed for permanent installation. Do not use

this light for any other purposes.

BA_Chip_Leuchte_Stationaer_130701.indd 8 01.07.13 10:56

9

D

Chip LED Light Operating Instructions

SAFETY NOTES

1. The light must be installed and serviced by a qualied technician.

2. Always turn o the power supply before installing or servicing the

light.

3. The light must be properly earthed.

4. Do not use this light without properly attached gaskets!

5. LED lights are extremely bright! Avoid looking straight into an LED

light beam, as doing so could result in irreversible eye damage.

6. Damaged protective covers must be replaced with an original

Brennenstuhl protective cover before the light can be used again.

7. If the mains supply cable of the light is damaged it must be replaced

by a qualied technician in order to avoid risks.

MOUNTING AND CONNECTION TO THE POWER SUPPLY

1. Do not attach the light to a surface that is subject to vibrations.

2. Mounting position: If possible the light should be mounted using

the wall bracket. Lights with a motion detector must be mounted

as shown in Fig. 1.

3. Mark the position of the bore-holes that are needed to attach the

wall bracket and drill the required holes in the wall. Attach the

bracket to the wall using suitable screws.

4. Open the light’s terminal box.

BA_Chip_Leuchte_Stationaer_130701.indd 9 01.07.13 10:56

10

D

Operating Instructions Chip LED Light

5. Guide the connecting cable through the cable gland and connect

it to the light’s lustre terminal as shown in Fig. 2 (left image shows

10W version, right image shows 30W version and higher. N = blue

cable, earthing symbol = green / yellow cable, L = brown cable).

6. Make sure the cable is securely fastened in the cable gland.

7. Replace the cover of the terminal box. Make sure the gasket is

seated correctly.

8. Fasten the light to the wall bracket using the screws and nuts

included with the package. Set the light to the desired position

and tighten the screws.

DESCRIPTION OF OPERATION

(For Versions with a Motion Detector)

The light is equipped with an infrared sensor. It turns on automatically

whenever the sensor detects movement in its vicinity

Try not to aim the motion detector in the direction of swimming pools,

heater vents, air conditioners or objects which are subject to large

variations in temperature. Avoid pointing the motion detector at trees

or shrubs and at areas where pets like to move about.

Make sure when mounting the light that the motion detector is most

sensitive to things that move through its detection range from side

to side and least sensitive to things that move straight at the device.

ADJUSTING THE MOTION DETECTOR

There are three knobs on the underside of the light (see Fig. 3).

Setting the time (TIME):

Use the TIME knob to set how long the light remains on after the last

movement (between 10 seconds and 4minutes). Turn the TIME knob

clockwise to increase the time span.

BA_Chip_Leuchte_Stationaer_130701.indd 10 01.07.13 10:56

11

D

Chip LED Light Operating Instructions

Sensitivity (SENS):

This knob can be used to adjust the sensitivity of the sensor. Turn the

SENS knob clockwise to increase sensitivity.

Light Setting (LUX):

The LUX setting determines how dark it must be before the sensor

turns on the light. The sun symbol () shows that the sensor is active

during the day and at night. If the knob is set to moon (), the sensor

only works at night. To adjust the sensor, wait until the desired level

of ambient light has been reached. Turn the knob all the way to the

moon symbol (), then turn the knob slowly towards the sun symbol

() until the light turns on if movement is detected.

The light will thereafter turn on automatically at the preset level of

darkness whenever a movement is detected.

Motion detector: passive infrared sensor

Detection range: up to 12m / up to 180 ° (horizontal)

Time setting: approx. 10 sec–4min

MAINTENANCE AND CLEANING

All maintenance work must be carried out by a qualied electrician.

PLEASE NOTE: The LED light does not contain parts that need servicing.

The LED light source cannot be replaced. If necessary, replace the

entire light.

Do not use solvents, corrosive cleaners or the like. Use a dry or slightly

moist cloth for cleaning ONLY.

BA_Chip_Leuchte_Stationaer_130701.indd 11 01.07.13 10:56

12

D

Operating Instructions Chip LED Light

Dispose of electrical devices in an environmentally

responsible manner!

Do not dispose of electrical devices with household

rubbish!

In accordance with Directive 2012/19/EU on waste electrical

and electronic equipment, used electrical equipment

must be collected separately and reused or recycled in an

environmentally responsible manner.

Please contact your local authorities for available disposal

options for your worn-out device.

Addresses

Hugo Brennenstuhl GmbH & Co. KG

Seestraße 1 – 3 ∙ 72074 Tübingen ∙ Germany

H. Brennenstuhl S.A.S.

F-67460 Souelweyersheim

lectra-t ag

Blegistrasse 13 ∙ CH-6340 Baar

www.brennenstuhl.com

BA_Chip_Leuchte_Stationaer_130701.indd 12 01.07.13 10:56

Page is loading ...

BA_Chip_Leuchte_Stationaer_130701.indd 103 01.07.13 10:56

Hugo Brennenstuhl GmbH & Co. KG

Seestraße 1 – 3 · D-72074 Tübingen · Germany

H. Brennenstuhl S.A.S.

F-67460 Souelweyersheim

lectra-t ag

Blegistrasse 13 · CH-6340 Baar

www.brennenstuhl.com

0472362/613

BA_Chip_Leuchte_Stationaer_130701.indd 104 01.07.13 10:56

Brennenstuhl 1171250101 Datasheet

Related papers

Other documents