Flex L 14-11 125 Owner's manual

Page is loading ...

Originalbetriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . 3

Original operating instructions . . . . . . . . . . . . . . . . . . . 16

Notice d’instructions d’origine . . . . . . . . . . . . . . . . . . . 28

Istruzioni per l’uso originali . . . . . . . . . . . . . . . . . . . . . . 41

Instrucciones de funcionamiento originales . . . . . . . . . 54

Instruções de serviço originais . . . . . . . . . . . . . . . . . . . 67

Originele gebruiksaanwijzing . . . . . . . . . . . . . . . . . . . . 80

Originale driftsvejledning . . . . . . . . . . . . . . . . . . . . . . . 93

Originale driftsanvisningen . . . . . . . . . . . . . . . . . . . . . . 106

Originalbruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . 119

Alkuperäinen käyttöohjekirja . . . . . . . . . . . . . . . . . . . . 130

Αυθεντικές οδηγίες χειρισμού . . . . . . . . . . . . . . . . . . . . . 143

Instrukcja oryginalna . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Eredeti üzemeltetési útmutató . . . . . . . . . . . . . . . . . . . 171

Originální návod k obsluze . . . . . . . . . . . . . . . . . . . . . 184

Originálny návod na obsluhu . . . . . . . . . . . . . . . . . . . . 197

Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . 210

Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . 222

Lietošanas pamācības oriģināls . . . . . . . . . . . . . . . . . 235

Оригинальная инструкция по эксплуатации

. . . . . .

248

Page is loading ...

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

16

Contents

Symbols used in this manual . . . . . . . . . 16

Symbols on the power tool . . . . . . . . . . 16

For your safety . . . . . . . . . . . . . . . . . . . 16

Noise and vibration . . . . . . . . . . . . . . . . 19

Technical specifications . . . . . . . . . . . . 20

Overview . . . . . . . . . . . . . . . . . . . . . . . . 22

Instructions for use . . . . . . . . . . . . . . . . 23

Maintenance and care . . . . . . . . . . . . . . 26

Disposal information . . . . . . . . . . . . . . . 26

-Declaration of Conformity . . . . . . . . 26

Exemption from liability . . . . . . . . . . . . . 27

Symbols used in this manual

WARNING!

Denotes impending danger. Non-

observance of this warning may result

in death or extremely severe injuries.

CAUTION!

Denotes a possibly dangerous situation.

Non-observance of this warning may result

in slight injury or damage to property.

NOTE

Denotes application tips and important

information.

Symbols on the power tool

Before switching on the power

tool, read the operating manual!

Wear goggles!

Protection class II

(completely insulated)

Disposal information for the old

machine (see page 26)!

Prevents kickback of the machine

if the tool becomes blocked.

Overload protection: switches the

machine off in the event of

overload.

A tachogenerator prevents the

speed from falling under load.

Better work safety and improved

handling thanks to gentle speed

development.

Sensor-controlled temperature

monitoring: If there is a risk of over-

heating the machine switches off.

Prevents unintentional machine

start after a power failure.

The speed can be set variably in 6

stages.

Brake system reduces run-on

period of tool.

Micro-processor electronics

For your safety

WARNING!

Before using the angle grinder, please read

and follow:

–

these operating instructions,

–

the “General safety instructions” on the

handling of power tools in the enclosed

booklet (leaflet-no.: 315.915),

–

the currently valid site rules and the

regulations for the prevention of

accidents.

This angle grinder is state of the art and has

been constructed in accordance with the

acknowledged safety regulations.

Nevertheless, when in use, the power tool

may be a danger to life and limb of the user

or a third party, or the power tool or other

property may be damaged. The angle

grinder may be operated only if it is

–

as intended,

–

in perfect working order.

Faults which impair safety must be repaired

immediately.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

17

Intended use

This angle grinder

– for commercial use in industry and trade,

– is designed for dry grinding and cutting

metal and stone; a special cutting guard

must be used for cutting,

– for use with grinding tools and acces-

sories which are indicated in these

instructions or recommended by the

manufacturer.

Not permitted are e.g. chain cutting wheels,

saw blades.

Safety Warnings for Angle Grinder

WARNING!

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and

instructions may result in electric shock, fire

and/or serious injury. Save all warnings and

instructions for future reference.

Safety Warnings Common for Grinding

or Abrasive Cutting-Off Operations



This power tool is intended to function as

a grinder or cut-off tool. Read all safety

warnings, instructions, illustrations and

specifications provided with this power

tool.

Failure to follow all instructions listed

below may result in electric shock, fire and/

or serious injury.



Operations such as sanding, wire

brushing or polishing are not recommen-

ded to be performed with this power tool.

Operations for which the power tool was

not designed may create a hazard and

cause personal injury.



Do not use accessories which are not

specifically designed and recommended

by the tool manufacturer. J

ust because the

accessory can be attached to your power

tool, it does not assure safe operation.



The rated speed of the accessory must be

at least equal to the maximum speed

marked on the power tool.

Accessories

running faster than their rated speed can

break and fly apart.



The outside diameter and the thickness of

your accessory must be within the

capacity rating of your power tool.

Incorrectly sized accessories cannot be

adequately guarded or controlled.



Threaded mounting of accessories must

match the grinder spindle thread. For

accessories mounted by flanges, the

arbour hole of the accessory must fit the

locating diameter of the flange.

Accessories that do not match the

mounting hardware of the power tool will

run out of balance, vibrate excessively and

may cause loss of control.



Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess

wear, wire brush for loose or cracked

wires. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting

and installing an accessory, position

yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for

one minute.

Damaged accessories will

normally break apart during this test time.



Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments.

The eye protection

must be capable of stopping flying debris

generated by various operations. The dust

mask or respirator must be capable of

filtrating particles generated by your

operation. Prolonged exposure to high

intensity noise may cause hearing loss.



Keep bystanders a safe distance away

from work area. Anyone entering the work

area must wear personal protective

equipment.

Fragments of workpiece or of

a broken accessory may fly away and

cause injury beyond immediate area of

operation.



Hold the power tool by insulated gripping

surfaces only, when performing an

operation where the cutting accessory

may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire

may make exposed metal parts of the

power tool “live” and could give the

operator an electric shock.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

18



Position the cord clear of the spinning

accessory.

If you lose control, the cord

may be cut or snagged and your hand or

arm may be pulled into the spinning

accessory.



Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the

surface and pull the power tool out of your

control.



Do not run the power tool while carrying it

at your side.

Accidental contact with the

spinning accessory could snag your

clothing, pulling the accessory into your

body.



Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation

of powdered metal may cause electrical

hazards.



Do not operate the power tool near

flammable materials.

Sparks could ignite

these materials.



Do not use accessories that require liquid

coolants.

Using water or other liquid

coolants may result in electrocution or

shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power

tool to be forced in the direction opposite of the

accessory’s rotation at the point of the

binding.For example, if an abrasive wheel is

snagged or pinched by the workpiece, the

edge of the wheel that is entering into the pinch

point can dig into the surface of the material

causing the wheel to climb out or kick out. The

wheel may either jump toward or away from

the operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions. Kickback is the result of power tool

misuse and/or incorrect operating procedures

or conditions and can be avoided by taking

proper precautions as given below.



Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use

auxiliary handle, if provided, for maximum

control over kickback or torque reaction

during start-up.

The operator can control torque reactions

or kickback forces, if proper precautions

are taken.



Never place your hand near the rotating

accessory.

Accessory may kickback over

your hand.



Do not position your body in the area

where power tool will move if kickback

occurs.

Kickback will propel the tool in

direction opposite to the wheel’s

movement at the point of snagging.



Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory.

Corners, sharp

edges or bouncing have a tendency to

snag the rotating accessory and cause

loss of control or kickback.



Do not attach a saw chain woodcarving

blade or toothed saw blade.

Such blades

create frequent kickback and loss of

control.

Safety Warnings Specific for Grinding

and Abrasive Cutting-Off Operations



Use only wheel types that are recommen-

ded for your power tool and the specific

guard designed for the selected wheel.

Wheels for which the power tool was not

designed cannot be adequately guarded

and are unsafe.



The grinding surface of centre depressed

wheels must be mounted below the plane

of the guard lip.

An improperly mounted

wheel that projects through the plane of

the guard lip cannot be adequately

protected.



The guard must be securely attached to

the power tool and positioned for

maximum safety, so the least amount of

wheel is exposed towards the operator.

The guard helps to protect the operator

from broken wheel fragments, accidental

contact with wheel and sparks that could

ignite clothing.



Wheels must be used only for recommen-

ded applications. For example: do not

grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for

peripheral grinding; side forces applied to

these wheels may cause them to shatter.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

19



Always use undamaged wheel flanges

that are of correct size and shape for your

selected wheel.

Proper wheel flanges

support the wheel thus reducing the

possibility of wheel breakage. Flanges for

cut-off wheels may be different from

grinding wheel flanges.



Do not use worn down wheels from larger

power tools.

Wheel intended for larger

power tool is not suitable for the higher

speed of a smaller tool and may burst.

Additional Safety Warnings specific for

Abrasive Cutting-Off Operations



Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

binding of the wheel in the cut and the

possibility of kickback or wheel breakage.



Do not position your body in line with and

behind the rotating wheel.

When the

wheel, at the point of operation, is moving

away from your body, the possible

kickback may propel the spinning wheel

and the power tool directly at you.



When wheel is binding or when

interrupting a cut for any reason, switch off

the power tool and hold the power tool

motionless until the wheel comes to a

complete stop.

Never attempt to remove

the cut-off wheel from the cut while the

wheel is in motion otherwise kickback may

occur. Investigate and take corrective

action to eliminate the cause of wheel

binding.



Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut.

The wheel

may bind, walk up or kickback if the power

tool is restarted in the workpiece.



Support panels or any oversized

workpiece to minimize the risk of wheel

pinching and kickback.

Large workpieces

tend to sag under their own weight.

Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.



Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water

pipes, electrical wiring or objects that can

cause kickback.

Additional safety instructions



The mains voltage and the voltage

specifications on the rating plate must

correspond.



Do not press the spindle lock until the

grinding tool stops.

Noise and vibration

NOTE

Values for the A-weighted sound pressure

level and for the total vibration values can

be found in the “Technical specifications”

table.

The noise and vibration values have been

determined in accordance with EN 60745.

CAUTION!

The indicated measurements refer to new

power tools. Daily use causes the noise and

vibration values to change.

NOTE

The vibration emission level given in this

information sheet has been measured in

accordance with a standardised test given

in EN 60745 and may be used to compare

one tool with another. It may be used for

a preliminary assessment of exposure. The

declared vibration emission level represents

the main applications of the tool. However if

the tool is used for different applications,

with different accessories or poorly

maintained, the vibration emission may

differ. This may significantly increase the

exposure level over the total working period.

However if the tool is used for different

applications, with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly decrease

the exposure level over the total working

period.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

20

Identify additional safety measures to

protect the operator from the effects of

vibration such as: maintain the tool and the

accessories, keep the hands warm,

organisation of work patterns.

CAUTION!

Wear ear protection at a sound pressure

above 85 dB(A).

Technical specifications

L 8-11 115 L 8-11 125 LE 9-11 125 L 10-11 125

Machine type Angle grinderr

Max. grinding tool Ø

mm

115 125

Grinding tool thickness

mm

1–6

Shaft thread

mm

22.23

Spindle thread M14

Speed

r.p.m.

11,500 6,000–11,500 11,500

Power input

W

800 900 1050

Power output

W

460 600 650

Weight according to “EPTA

Procedure 01/2003”

(without power cord)

kg

2.0 2.1

Protection class

II/

A-weighted sound pressure level according to EN 60745 (see “Noise and vibration”):

Sound pressure level L

pA

dB(A)

86.4 87 85

Sound power level L

WA

dB(A)

97.4 98 96

Uncertainty K

db

3.0

Total vibration value according to EN 60745 (see “Noise and vibration”):

Emission value a

h

when

grinding surfaces

m/s

2

7.7 8.5 6.3

Emission value a

h

when

cutting-off

m/s

2

3.0 1.6

Uncertainty K

m/s

2

1.5

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

21

L 14-11 115 L 14-11 125 LE 14-11 115 LE 14-11 125

Machine type Angle grinderr

Max. grinding tool Ø

mm

115 125 115 125

Grinding tool thickness

mm

1–6

Shaft thread

mm

22.23

Spindle thread M14

Speed

r.p.m.

11,500 2,800–11,500

Power input

W

1400

Power output

W

880

Weight according to

“EPTA Procedure

01/2003” (without power

cord)

kg

2.3

Protection class

II/

A-weighted sound pressure level according to EN 60745 (see “Noise and vibration”):

Sound pressure level L

pA

dB(A)

86

Sound power level L

WA

dB(A)

97

Uncertainty K

db

3.0

Total vibration value according to EN 60745 (see “Noise and vibration”):

Emission value a

h

when

grinding surfaces

m/s

2

6.3

Emission value a

h

when

cutting-off

m/s

2

1.4

Uncertainty K

m/s

2

1.5

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

22

Overview

Different electric power tools are described in these instructions. The illustrated electric power

tool may differ in detail from the one which you purchased.

1 Spindle

2 Threaded flange

a Clamping nut

b Clamping flange

3 Guard hood

Can be adjusted without a tool through

360° by means of 12 notches.

a) 115 mm (L 8-11 115, L 14-11 115,

LE 14-11 115)

b) 125 mm

4 Handle

Handle can be fitted to the left or right.

(L 14-11 115, L 14-11 125, LE 14-11 115,

LE 14-11 125: handle with integrated

pin wrench)

5 Spindle lock

Secures the spindle when the tool

is changed.

6 Gear head

With air outlet and direction-of-rotation

arrow.

7 Switch rocker

Switches the power tool on and off.

With notched position for continuous

operation.

8 Rear handle

9 Dial for preselecting the speed

(LE 9-11 125, LE 14-11 115,

LE 14-11 125)

10 4.0 m power cord with plug

11 Rating plate (not illustrated)

12 Face spanner

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

23

Instructions for use

WARNING!

Before carrying out any work on the angle

grinder, always pull out the mains plug.

Before switching on the power tool

Unpack the angle grinder and check that

there are no missing or damaged parts.

Attach the guard

WARNING!

When using the angle grinder for roughing or

cutting, never work without the guard.

A special cutting guard must be used for cutting.

 Pull out the mains plug.

 Attach the guard (1.). Lugs on the guard

hood must be located in the flange

recesses (2.).

 Turn guard hood clockwise.

Rotation is possible in one direction only!

 Remove in reverse order.

Attach the handle

NOTE

It is not permitted to operate the electric

power tool without the handle.

Attaching/changing the tool

 Pull out the mains plug.

Attach the grinding wheel

 Press and hold down the spindle lock (1.).

 Using the face spanner, loosen the

clamping nut on the spindle in an anti-

clockwise direction and remove (2.).

Handle

(L 14-11 115, L 14-11 125, LE 14-11 115,

LE 14-11 125)

 Remove the handle from the power tool

by rotating it in an anti-clockwise

direction.

 Rotate the cover on the handle by 180°

until it engages.

 The stop key is released.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

24

 Press and hold down the spindle lock (1.).

 Using the stop key, loosen the clamping

nut on the spindle in an anti-clockwise

direction and remove (2.).

 Insert the grinding wheel in the correct

position.

 Screw the clamping nut with flange face

up, onto the spindle.

 Press and hold down the spindle lock.

 Tighten the clamping nut with the pin

wrench or stop key.

 Carry out a test run to check that the tool

is clamped in the centre.

Test run

 Insert the mains plug into the socket.

 Switch on the angle grinder with the

switch (without engaging it) and run the

angle grinder for approx. 30 seconds.

Check for imbalances and vibrations.

 Switch off the angle grinder.

Switching on and off

Brief operation without engaged switch

rocker

 Push the switch rocker forwards and

hold in position.

 To switch off the power tool, release

the switch rocker.

Continuous operation with engaged

switch rocker

 Push the switch rocker forwards (1.) and

engage by pressing the front end (2.).

 To switch off the power tool, release the

switch rocker by pressing the rear end.

NOTE

Following a power failure, the switched on

power tool does not restart.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

25

Preselecting the speed

(LE 9-11 125, LE 14-11 115,

LE 14-11 125)

 To set the operating speed, move the dial

to the required value.

CAUTION!

Risk of injury due to destruction of the tool.

Use the appropriate tool for the job.

NOTE

If an overload or overheating occurs during

continues operation, the power tool auto-

matically reduces the speed until the power

tool has cooled down adequately.

Adjusting the guard

To adjust the tool to the task at hand, the

guard hood can be adjusted by 12 notches

on 360° without a tool.

CAUTION!

Risk of injury! Wear protective gloves.

 Pull out the mains plug.

 Turn guard hood opposite to the

direction-of-rotation arrow on the gear

head to the required position.

Work instructions

NOTE

When the power tool is switched off,

the grinding tool continues running briefly.

Rough-grinding

WARNING!

Never use cutting-off wheels for rough-

grinding.

– Angle of wheel 20–40° for best cutting

performance.

– Applying moderate pressure, move the

angle grinder backwards and forwards.

As a result, the workpiece will not

become too hot and there will be no

discoloration; nor will there be any

grooves.

Cut-off grinding

WARNING!

A special cutting guard must be used for

cutting.

See manufacturer’s accessories catalogue.

– Do not press, tilt or oscillate the power

tool.

– The angle grinder must always be

operated backwards.

Otherwise, there is a risk of the angle

grinder jumping uncontrollably out of the

groove.

– Adjust the feed to the material which is to

be cut: the harder the material, the slower

the feed.

For further information on the manufac-

turer’s products go to www.flex-tools.com

.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

26

Maintenance and care

WARNING!

Before carrying out any work on the angle

grinder, always pull out the mains plug.

Cleaning

WARNING!

If metals are ground or cut over a prolonged

period, conductive dust may become

deposited inside the housing. Impairment of

the protective insulation! Operate the power

tool via a residual-current-operated circuit-

breaker (tripping current 30 mA).

 Regularly clean the power tool and

ventilation slots. Frequency of cleaning is

dependent on the material and duration

of use.

 Regularly blow out the housing interior

and motor with dry compressed air.

Carbon brushes

The angle grinder features cut-off carbon

brushes.

When the wear limit of the cut-off carbon

brushes is reached, the angle grinder

switches off automatically.

NOTE

Use only original parts supplied by the

manufacturer for replacement purposes.

If non-original parts are used, the guarantee

obligations of the manufacturer will be

deemed null and void.

When the power tool is being used, the

carbon brushes can be seen sparking

through the rear air inlet apertures. If the

carbon brushes spark excessively, switch

off the angle grinder immediately. Take the

angle grinder to a customer service

workshop authorised by the manufacturer.

Gears

NOTE

Do not loosen the screws on the gear head

during the warranty period. Non-compliance

will deem the guarantee obligations of the

manufacturer null and void.

Repairs

Repairs may be carried out by an authorised

customer service centre only.

Spare parts and accessories

For other accessories, in particular grinding

tools, see the manufacturer’s catalogues.

Exploded drawings and spare-part lists can

be found on our homepage:

www.flex-tools.com

Disposal information

WARNING!

Render redundant power tools unusable

by removing the power cord.

EU countries only

Do not throw electric power tools

into the household waste!

In accordance with the European Directive

2012/19/EU on Waste Electrical and

Electronic Equipment and transposition into

national law used electric power tools must

be collected separately and recycled in an

environmentally friendly manner.

NOTE

Please ask your dealer about disposal

options!

-Declaration of Conformity

We declare under our sole responsibility

that the product described under “Technical

specifications” conforms to the following

standards or normative documents:

EN 60745 in accordance with the

regulations of the directives 2014/30/EU

2006/42/EC, 2011/65/EU.

L 8-11 115/L 8-11 125/LE 9-11 125/L 10-11 125/L 14-11 115/L 14-11 125/LE 14-11 115/LE 14-11 125

27

Responsible for technical documents:

FLEX-Elektrowerkzeuge GmbH, R & D

Bahnhofstrasse 15, D-71711 Steinheim/Murr

05.11.2018

FLEX-Elektrowerkzeuge GmbH

Bahnhofstrasse 15, D-71711 Steinheim/Murr

Exemption from liability

The manufacturer and his representative

are not liable for any damage and lost profit

due to interruption in business caused

by the product or by an unusable product.

The manufacturer and his representative are

not liable for any damage which was caused

by improper use of the product or by use of the

product with products from other

manufacturers.

Page is loading ...

Flex L 14-11 125 Owner's manual

Flex L 14-11 125 Owner's manual

in other languages

Related papers

Other documents