TOA SX-200IP User manual

Brand: TOA

Model: SX-200IP

Type: User manual

INSTALLATION MANUAL

IP INTERFACE MODULE SX-200IP

Thank you for purchasing TOA’s IP Interface Module.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

1. SAFETY PRECAUTIONS

• Beforeinstallation oruse,besuretocarefully readalltheinstructions inthis section forcorrect andsafe

operation.

• Besuretofollowalltheprecautionaryinstructionsinthissection,whichcontainimportantwarningsand/or

cautions regarding safety.

• Afterreading,keepthismanualhandyforfuturereference.

2. GENERAL DESCRIPTION

The SX-200IP, designed to be installed in the SX-2100AI Audio input unit of the SX-2000 series, is an Interface

module for connection to the N-8000 series.

ByconnectingtheSX-200IPtoanetwork(LANorWAN),pagingannouncementscanbemadetotheSX-2000

systemusingtheN-8000series’station(s)(N-8600MSandN-8610RM)employingthepacketaudiotechnology.

Each function is set by the dedicated setting software on a PC.

3. FEATURES

• Upto8SX-200IPscanbeusedperSX-2000System.

• Pagingannouncementscanbemadetoupto8SX-2000systemsusingtheSX-200IPs.

4. SPECIFICATIONS

Network Section NetworkI/F: 10BASE-T/100BASE-TX(Automatic-Negotiation)

Networkprotocol: TCP/IP,UDP,HTTP,RTP,ARP,ICMP,IGMP

Connector: RJ45connector forLAN

Voicesamplingfrequency: 16kHz,8kHz(controllableonthesoftware)

 48kHzsamplerateisusedforSX-2000systemonly.

Quantifyingbitnumber: 16bits

Voiceencodingmethod: Sub-bandADPCM,Cryptosystem

Voicepacketlossrecovery: Silenceinsertion

Audiodelaytime: 80ms,320ms(controllableonthesoftware)

Indicator Operationindicator(RUN)

Operating Temperature 0to40ºC

OperatingHumidity 90%RHorless(nocondensation)

Finish Panel:Pre-coatedsteelplate,black,30%gloss

Dimensions 35(w)x119.5(h)x178.4(d)mm

Weight 150g

Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.

Indicatesapotentiallyhazardoussituationwhich,

if mishandled, could result in death or serious

personalinjury.

WARNING

• Do not expose the unit to rain or an environment

where it may be splashed by water or other liquids,

asdoingsomayresultinreorelectricshock.

• Should the following irregularity be found during

use, immediately turn off the power supply to the

SX-2100AI Audio Input Unit where the SX-200IP

is installed and contact your nearest TOA dealer.

Make no further attempt to operate the unit in this

conditionasthismaycausereorelectricshock.

· If you detect smoke or a strange smell coming

from the unit

· Ifwaterormetallicobjectgetsonthecircuitboard

· If the unit falls or breaks

· Ifitismalfunctioning(notonesounds.)

5. MODULE INSTALLATION

Notes

• MakesurethatthepowerisswitchedOFFbeforeattachingordetachingSX-200IPs.

• Toavoidfailuresduetostaticelectricity,donottouchthepartsontheSX-200IPcircuitboard.

• EnsurethattheSX-200IPisinstalledandsecuredwithscrewsinthecorrectposition.

• Twosilverslottedscrewsattheleftandrightsidesofthefrontpanelarehandlesusedformoduledetachment.

Never rotate them because they do not function as screws.

Step 1. Removetheblankpanelattached

to the SX-2100AI’s slot.

Step 2. Mount the SX-200IP.

Insert the SX-200IP and x it in

place using the screws (Machine

screwsM3x6)removedinStep1.

Blank panel

SX-2100AI

Machine screw M3 x 6

(screw removed in Step 1)

Handle

SX-200IP

6. CONNECTION

Note

UsableLANcableisaSTPCategory5orgreaterstraightthrough

cable only.

AUTPcablecannotbeused.

RJ-45 connector

LAN cable

SX-200IP

To network

LINK/ACT 10/100M

LAN

RESET RUN

IP INTERFACE MODULE

model SX-200IP

FOR SX-2000 SERIES ONLY

7. NOTES ON SETTING

It is necessary to perform SX-200IP setting using both the SX-2000 Setting software and N-8000 Setting

software.

7.1. SX-2000 Setting Software

TheSX-200IPisrecognizedasthe“D-922E/F”intheSX-2000system.SettheSX-200IPasthe“D-922E/F”on

theSX-2000Settingsoftware.Forthesettings,readtheSX-2000Softwareinstructionmanual.

7.2. N-8000 Setting Software

Forthesettings,readchapter5oftheN-8000seriesinstructionmanual.

URL:http://www.toa.jp/

133-22-400-10

Traceability Information for Europe

Manufacturer:

TOA Corporation

7-2-1,Minatojima-Nakamachi,Chuo-ku,Kobe,Hyogo,Japan

Authorizedrepresentative:

TOAElectronicsEuropeGmbH

Suederstrasse282,20537Hamburg,Germany

8. SX-200IP OPERATING REQUIREMENTS IN THE SX-2000 SYSTEM

•TheSX-2000SettingSoftwareusedforSX-2000systemsettingsshouldbeVersion3.10orlater.

•TheSX-2000systemcomponentsshouldbeofthefollowingrmwareversions.

SX-2000SM, SX-2100AI, SX-2000AO, SX-2100AO Version3.10orlater

SX-2000CI, SX-2000CO Version 2.01 or later

TOA SX-200IP User manual

TOA SX-200IP User manual

Related papers

Other documents