Optimus SX-200IP User manual

  • Hello! I am an AI chatbot trained to assist you with the Optimus SX-200IP User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION MANUAL
IP INTERFACE MODULE SX-200IP
Thank you for purchasing TOA’s IP Interface Module.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. SAFETY PRECAUTIONS
• Beforeinstallation oruse,besuretocarefully readalltheinstructions inthis section forcorrect andsafe
operation.
• Besuretofollowalltheprecautionaryinstructionsinthissection,whichcontainimportantwarningsand/or
cautions regarding safety.
• Afterreading,keepthismanualhandyforfuturereference.
2. GENERAL DESCRIPTION
The SX-200IP, designed to be installed in the SX-2100AI Audio input unit of the SX-2000 series, is an Interface
module for connection to the N-8000 series.
ByconnectingtheSX-200IPtoanetwork(LANorWAN),pagingannouncementscanbemadetotheSX-2000
systemusingtheN-8000seriesstation(s)(N-8600MSandN-8610RM)employingthepacketaudiotechnology.
Each function is set by the dedicated setting software on a PC.
3. FEATURES
• Upto8SX-200IPscanbeusedperSX-2000System.
• Pagingannouncementscanbemadetoupto8SX-2000systemsusingtheSX-200IPs.
4. SPECIFICATIONS
Network Section NetworkI/F: 10BASE-T/100BASE-TX(Automatic-Negotiation)
Networkprotocol: TCP/IP,UDP,HTTP,RTP,ARP,ICMP,IGMP
Connector: RJ45connector forLAN
Voicesamplingfrequency: 16kHz,8kHz(controllableonthesoftware)
48kHzsamplerateisusedforSX-2000systemonly.
Quantifyingbitnumber: 16bits
Voiceencodingmethod: Sub-bandADPCM,Cryptosystem
Voicepacketlossrecovery: Silenceinsertion
Audiodelaytime: 80ms,320ms(controllableonthesoftware)
Indicator Operationindicator(RUN)
Operating Temperature 0to40ºC
OperatingHumidity 90%RHorless(nocondensation)
Finish Panel:Pre-coatedsteelplate,black,30%gloss
Dimensions 35(w)x119.5(h)x178.4(d)mm
Weight 150g
Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.
Indicatesapotentiallyhazardoussituationwhich,
if mishandled, could result in death or serious
personalinjury.
WARNING
• Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
asdoingsomayresultinreorelectricshock.
• Should the following irregularity be found during
use, immediately turn off the power supply to the
SX-2100AI Audio Input Unit where the SX-200IP
is installed and contact your nearest TOA dealer.
Make no further attempt to operate the unit in this
conditionasthismaycausereorelectricshock.
· If you detect smoke or a strange smell coming
from the unit
· Ifwaterormetallicobjectgetsonthecircuitboard
· If the unit falls or breaks
· Ifitismalfunctioning(notonesounds.)
5. MODULE INSTALLATION
Notes
• MakesurethatthepowerisswitchedOFFbeforeattachingordetachingSX-200IPs.
• Toavoidfailuresduetostaticelectricity,donottouchthepartsontheSX-200IPcircuitboard.
• EnsurethattheSX-200IPisinstalledandsecuredwithscrewsinthecorrectposition.
• Twosilverslottedscrewsattheleftandrightsidesofthefrontpanelarehandlesusedformoduledetachment.
Never rotate them because they do not function as screws.
Step 1. Removetheblankpanelattached
to the SX-2100AI’s slot.
Step 2. Mount the SX-200IP.
Insert the SX-200IP and x it in
place using the screws (Machine
screwsM3x6)removedinStep1.
2
1
Blank panel
SX-2100AI
Machine screw M3 x 6
(screw removed in Step 1)
Handle
SX-200IP
6. CONNECTION
Note
UsableLANcableisaSTPCategory5orgreaterstraightthrough
cable only.
AUTPcablecannotbeused.
RJ-45 connector
LAN cable
SX-200IP
To network
LINK/ACT 10/100M
LAN
RESET RUN
IP INTERFACE MODULE
model SX-200IP
FOR SX-2000 SERIES ONLY
7. NOTES ON SETTING
It is necessary to perform SX-200IP setting using both the SX-2000 Setting software and N-8000 Setting
software.
7.1. SX-2000 Setting Software
TheSX-200IPisrecognizedasthe“D-922E/F”intheSX-2000system.SettheSX-200IPasthe“D-922E/F”on
theSX-2000Settingsoftware.Forthesettings,readtheSX-2000Softwareinstructionmanual.
7.2. N-8000 Setting Software
Forthesettings,readchapter5oftheN-8000seriesinstructionmanual.
URL:http://www.toa.jp/
133-22-400-10
Traceability Information for Europe
Manufacturer:
TOA Corporation
7-2-1,Minatojima-Nakamachi,Chuo-ku,Kobe,Hyogo,Japan
Authorizedrepresentative:
TOAElectronicsEuropeGmbH
Suederstrasse282,20537Hamburg,Germany
8. SX-200IP OPERATING REQUIREMENTS IN THE SX-2000 SYSTEM
•TheSX-2000SettingSoftwareusedforSX-2000systemsettingsshouldbeVersion3.10orlater.
•TheSX-2000systemcomponentsshouldbeofthefollowingrmwareversions.
SX-2000SM, SX-2100AI, SX-2000AO, SX-2100AO Version3.10orlater
SX-2000CI, SX-2000CO Version 2.01 or later
/