Tektronix THS3024 is a high-performance oscilloscope designed to meet the needs of demanding applications. With its advanced features and capabilities, the THS3024 is an ideal choice for engineers and technicians in a wide range of industries, including electronics, telecommunications, and automotive.
Some of the key features of the THS3024 include:
- 24 channels
- 1 GHz bandwidth
- 5 GS/s sample rate
- Large 12.1-inch capacitive touchscreen display
- Advanced triggering capabilities
- Comprehensive measurement and analysis tools
The THS3024 is ideal for a variety of applications, including:
Tektronix THS3024 is a high-performance oscilloscope designed to meet the needs of demanding applications. With its advanced features and capabilities, the THS3024 is an ideal choice for engineers and technicians in a wide range of industries, including electronics, telecommunications, and automotive.
Some of the key features of the THS3024 include:
- 24 channels
- 1 GHz bandwidth
- 5 GS/s sample rate
- Large 12.1-inch capacitive touchscreen display
- Advanced triggering capabilities
- Comprehensive measurement and analysis tools
The THS3024 is ideal for a variety of applications, including:
THS3000 Series Oscilloscopes
Declassification and Security
ZZZ
Instructions
xx
www.tektronix.com
*
P077060500*
077-0605-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverto
n, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.
Clear and Sanitize Procedures
If you have data security concerns, this document helps you to sanitize m emory
devices in the THS3000 Series Oscilloscopes.
If you have any questions, contact the Tektronix Technical Support Center at
http://www.tektronix.com/support.
Products
The following Tektronix products a re covered by this document:
THS3014
THS3024
Terms
The following terms may be used in this document:
Clear. This eradicates data on media/memory before reusing it in a secured
area. All reusable memory is cleared to deny acce
ss to previously stored
information by standard means of access.
Erase. This is equivalent to clear.
Media. Storage/data export device. A device that is used to store or export
data from the instrument, such as a USB port/USB flash drive.
Sanitize. This removes the data from media/memory so that the data cannot
be recovered using any known technology. This is typically used when the
device will be moved (temporarily or permanently) from a secured area to a
nonsecured area.
Scrub. This is equivalent to sanitize.
Remove. This is a physical means to clear the data by removing the memory
device from the instrument. Instructions are available in the product service
manual.
User Accessible. User is able to directly retrieve the memory device contents.
User-Modifiable. The memory device can be written to by the user during
normal instrument operation, using the instrument user interface or remote
control.
Volatile memory. Data is lost when the instrument is powered off.
Nonvolatile memory. Data is retained when the instrument is powered off.
Power off. Some instruments have a “Standby” mode, in which power is
still supplied to the instrument. For the purpose of clearing data, putting the
THS3000 Series Oscilloscopes Declassification and Security Instructions 1
Clear and Sanitize Procedures
instrument in S
tandby mode does not qualify as powering o ff. For these
products, you must either press a rear-panel OFF switch or remove the power
source from the instrument.
Instrument Declassification. A term that refers to procedures that must be
undertaken before an instrument can be removed from a sec ure environment.
Declassificat
ion procedures include memory sanitization and memory
removal, and sometimes both.
Memory Devices
The following table lists the volatile and nonvolatile memory devices in the
oscilloscopes.
Table 1: Memory Devices
Reference
designator Description Use
D4000
Controller “Spider” Contains a mask ROM 4k x 32 with a initial program with the operating
code for the oscilloscope and a RAM 1k x 32 to temporarily store stack
values for computing actions.
D4001
1x4MbSRAM.SRAMmemory
Used to store the actual screen and oscilloscope setup, and saved screens
and oscilloscope setups.
D5000, D5002
2 x 32 Mb Flash EEPROM Non-volatile memory used to store operating code (oscilloscope firmware)
for the product, and to store calibration constants.
D5001, D5003
2 x 8 Mb S RAM SRAM memory used to store the actual screen and oscilloscope setup,
and saved s creens and oscilloscope setups.
Memory Erasure
The operating code (instrument firmware)storedinD5000andD5002canbe
read and loaded using dedicated remote interface commands only available for
internal use by Tektronix.
Calibration constants stored in D5000 and D5002 can be read using special remote
interface commands only available for internal use by Tektronix. The calibration
constants are generated when the oscilloscope is sent through its calibration
process and are fundamental to the oscilloscope operation.
The saved screens and oscilloscope setups can be cleared from the oscilloscope by
using the following procedure:
1. Press the Save button.
2. Press F4 – FILE O PTIONS.
3. Select DELETE with the up/down arrow keys.
4. Press the Enter button.
2 THS3000 Series Oscilloscopes Declassification and Security Instructions
Clear and Sanitize Procedures
5. Press F2 – SELEC
TALL.
6. Press the Enter button.
7. Press F4 – YES to confirm the Clear action.
To clear all data stored in SRAM, disconnect the oscilloscope from all voltage
sources, open the battery door at the rear panel, and lift the battery out of the
instrument. Replace the battery after 10 minutes.
THS3000 Series Oscilloscopes Declassification and Security Instructions 3
-
1
-
2
-
3
-
4
-
5
Tektronix THS3024 Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Tektronix THS3024 is a high-performance oscilloscope designed to meet the needs of demanding applications. With its advanced features and capabilities, the THS3024 is an ideal choice for engineers and technicians in a wide range of industries, including electronics, telecommunications, and automotive.
Some of the key features of the THS3024 include:
- 24 channels
- 1 GHz bandwidth
- 5 GS/s sample rate
- Large 12.1-inch capacitive touchscreen display
- Advanced triggering capabilities
- Comprehensive measurement and analysis tools
The THS3024 is ideal for a variety of applications, including:
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Tektronix MDO3000 Series Instructions Manual
-
-
Tektronix MDO3 Series Owner's manual
-
Tektronix 6 series Instructions Manual
-
Tektronix MSO2024B Instructions Manual
-
-
Tektronix TDS3054C Owner's manual
-
-
Tektronix TLA6202 Operating instructions
-