Moffat FN8127E Operating instructions

Category
Deep fryers
Type
Operating instructions
I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l
Electric Deep Fryer
FN8127E
FN8127EE
FN8127E21
FN8127EE21
FN8224E
FN8224EE
228685-18
For use in GB & IE
FNL8127E
FNL8127EE
FNL8127E21
FNL8127EE21
FNL8224E
FNL8224EE
FNB8127E
FNB8127EE
FNB8127E21
FNB8127EE21
FNB8224E
FNB8224EE
FNLB8127E
FNLB8127EE
FNLB8127E21
FNLB8127EE21
FNLB8224E
FNLB8224EE
The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.
In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.
© Copyright Moffat Ltd. July 2019.
Moffat Limited
Rolleston 7675
New Zealand
AUSTRALIA
Moffat Pty Limited
Web: www.moffat.com.au
E.Mail: [email protected]m.au
Main Office: (tel) +61 (03) 9518 3888
(fax) +61 (03) 9518 3833
Service: (tel): 1800 622 216
Spares: (tel): 1800 337 963
Customer Service: (tel): 1800 335 315
(fax): 1800 350 281
CANADA
Serve Canada
Web: www.servecanada.com
Sales: (tel): 800 551 8795 (Toll Free)
Service: (tel): 800 263 1455 (Toll Free)
NEW ZEALAND
Moffat Limited
Web: www.moffat.co.nz
E.Mail: [email protected].nz
Main Office: (tel): 0800 663328
UNITED KINGDOM
Blue Seal
Web: www.blue-seal.co.uk
E.Mail: sales@blue-seal.co.uk
Sales: (tel): +44 121 327 5575
(fax): +44 121 327 9711
Spares: (tel): +44 121 322 6640
(fax): +44 121 327 9201
Service: (tel): +44 121 322 6644
(fax): +44 121 327 6257
UNITED STATES
Moffat
Web: www.moffat.com
Sales: (tel): 1800 551 8795 (Toll Free)
(fax): +1 336 661 9546
Service: (tel): 866 673 7937 (Toll Free)
(tel): +1 336 661 1556
(fax): +1 336 661 1660
REST OF WORLD
Moffat Limited
Web: www.moffat.co.nz
E.Mail: export@moffat.co.nz
FN(L)(B)8127E - 'Fast-Fri' Electric Fryer, Manual Control (Single Tank - 27ltr, 17kW).
FN(L)(B)8127EE - 'Fast-Fri' Electric Fryer, Digital Control (Single Tank - 27ltr, 17kW).
FN(L)(B)8127E21 - 'Fast-Fri' Electric Fryer, Manual Control (Single Tank - 27ltr, 21kW).
FN(L)(B)8127EE21 - 'Fast-Fri' Electric Fryer, Digital Control (Single Tank - 27ltr, 21kW).
FN(L)(B)8224E - 'Fast-Fri' Electric Fryer, Manual Control (Twin Tank - 24 ltr, 17kW).
FN(L)(B)8224EE - 'Fast-Fri' Electric Fryer, Digital Control (Twin Tank - 24 ltr, 17kW).
Model Numbers Covered in this Specification
Electrical Supply Requirements
Installation Requirements
Unpacking
Location
Clearances
Assembly
Fitting Rear Rollers
Electrical Connection
Commissioning
Operation Guide
Description of the Controls - FN8127E and FN8224E Models Only
Description of the Controls - FN8127EE and FN8224EE Models Only
Control Panel Functions - FN8127EE and FN8224EE Models Only
Controller Basic Programming Mode - FN8127EE andFN8224EE Models Only
Filling the Tank(s)
Operation of the Appliance
FN8127E and FN8224E Models Only
FN8127EE and FN8224EE Models Only
Over TemperatureControl System
General
Draining and Daily Cleaning
Weekly Cleaning
Periodic Maintenance
Guide to Cooking Problems with Fryer
Fault Finding the Electrical System
FN8127E Single Tank 17kW Model Only
FN8127E21 Single Tank 21kW Model Only
FN8224E Twin Tank 17kW Model Only
FN8127EE Single Tank 17kW Model Only
FN8127EE21 Single Tank 21kW Model Only
FN8224EE Twin Tank 17kW Model Only
Timing Mode.
Temperature Offset.
Temperature Display Mode.
Programming the Melt Cycle.
Setting the Temperature Units.
System Programmable Default Settings.
3
We are confident that you will be delighted with your WALDORF Electric Deep Fryer, and it will become a
most valued appliance in your commercial kitchen.
To ensure you receive the utmost benefit from your new Waldorf Electric Deep Fryer, there are two
important things you can do.
Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.
If you are unsure of any aspect of the installation, instructions or performance of your appliance,
contact your WALDORF dealer promptly. In many cases a phone call could answer your question.
These instructions are only valid if the country code appears on the appliance. If the country code is
not shown, refer to the appliance supplier to obtain the technical instructions for adapting the appliance
to the conditions for use in that country.
THE OPERATOR MUST TAKE GREAT CARE TO USE THE EQUIPMENT SAFELY AND TO GUARD IT AGAINST THE RISK
OF FIRE.
THE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.
IT IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICE PERSON TO
ENSURE CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE.
4
FN[1]8127E 'Fast-Fri' Electric Fryer, Manual Control (Single Tank - 27ltr, 17kW).
FN[1]8127EE 'Fast-Fri' Electric Fryer, Digital Control (Single Tank - 27ltr, 17kW).
FN[1]8127E21 'Fast-Fri' Electric Fryer, Manual Control (Single Tank - 27ltr, 21kW).
FN[1]8127EE21 'Fast-Fri' Electric Fryer, Digital Control (Single Tank - 27ltr, 21kW).
FN[1]8224E 'Fast-Fri' Electric Fryer, Manual Control (Twin Tank - 24 ltr, 17kW).
FN[1]8224EE 'Fast-Fri' Electric Fryer, Digital Control (Twin Tank - 24 ltr, 17kW).
NOTE:
[1]: - Model Options;
- - Standard.
L - Low Back.
B - Bold Front.
LB - Low Back and Bold Front.
When connecting a this electric appliance to the mains supply, ensure that the following is carried out:-
n isolating
switch accessible during manual operation of the appliance.
The supply cord shall be protected against any mechanical or thermal damage.
Refer to the appropriate wiring standards for the size of cable that is to be supplied to an appliance for the
current drawn on that line.
Model
Power Supply
Total Power
Input
Amps
Voltage Type Frequency
L1 L2 L3
FN8127E / EE 400-415Vac 3 P+N+E 50 / 60Hz 17kW 23.6 23.6 23.6
FN8127E21 / EE21 400-415Vac 3 P+N+E 50 / 60Hz 21kW 29.2 29.26 29.2
FN8224E / EE 400-415Vac 3 P+N+E 50 / 60Hz 17kW 23.6 23.6 23.6
THIS APPLIANCE MUST BE EARTHED. IF SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY
QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
5
FN(L)8127E
FN(L)8224E
6
FN(L)8224EE
FN(L)8127EE
7
NOTE: It is most important that this appliance is installed correctly and that operation is correct
before use. Installation shall comply with local electrical and health and safety
requirements.
Waldorf Deep Fryers are designed to provide years of satisfactory service, and correct installation is
essential to achieve the best performance, efficiency and trouble-free operation.
This appliance must be installed in accordance with National installation codes and in addition, in
accordance with relevant National / Local codes covering health and safety, electrical and fire safety.
Australia / New Zealand AS / NZS3000 - Wiring Rules.
United Kingdom: BS 7671 - Requirements for Electrical Installations.
Installations must be carried out by qualified service persons only. Failure to install the
equipment to the relevant codes and manufacturers specifications shown in this section will
void the warranty.
Remove all packaging and transit protection from appliance including all protective plastic coating
from door outer panel and exterior stainless steel panels.
Check equipment and parts for damage. Report any damage immediately to carrier and distributor.
Report any deficiencies to distributor who supplied appliance.
Check available electrical supply is correct to as shown on rating plate on inside of access door.
Check the following parts have been supplied with appliance:
FN8127E / EE FN8224E / EE
Baskets 2 2
Lid 1 1
Drain Extension 1 2
1. Any appliance requires adequate clearance and ventilation for optimum and trouble-free operation.
Minimum installation clearances shown below, are to be adhered to.
2. Position the Deep Fryer in its approximate working position.
3. Legs (rear rollers - optional) must always be fitted. Ensure the legs / rollers are securely attached.
NOTE:
Only non-combustible materials can be used in close proximity to this appliance.
To allow easy operation, drainage and servicing of the appliance, a minimum of 600mm
clearance should be maintained at front of appliance.
This model is delivered completely assembled. Ensure that the legs are securely attached.
NOTE:
This appliance is fitted with adjustable feet to enable it to be positioned securely and level
on uneven floors. This should be carried out on completion of gas connection. Refer to
'Gas Connection Section'.
The rear leg housings on this appliance can also be fitted with rear rollers to enable the
appliance to be easily moved for positioning and cleaning purposes. If desired, these
rollers are supplied in the packaging, with tappliance. See overleaf for fitting instructions.
Optional Accessories (Refer to Replacement Parts List)
Plinth Kit. For installation details, refer to the instructions supplied with each kit.
Left / Right Hand Side 50mm 0mm
Rear 25mm 0mm
8
1. Raise the appliance from the floor by approx. 75mm,
using suitable lifting equipment (i.e. Palletiser / Forklift)
to allow rear adjustable feet to be removed.
2. Unscrew and remove both rear adjustable feet from
rear leg housings.
3. Fit rear roller to rear leg housing and align screw hole
in side of rear leg housing with threaded hole in rear
roller.
4. Secure the rear roller to the leg support with bolt
supplied and tighten bolt.
5. Fit second roller and tighten securing bolt.
6. Lower appliance back to the floor and adjust front
adjustable feet to level appliance.
Appliance
Base
Adjustable
Foot
Rear
Roller
Rear Leg
Housing
Roller
Locating Bolt
Fig 1
9
NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY A QUALIFIED
PERSON.
Each fryer should be connected to an adequately protected power supply and an isolation switch mounted
adjacent to, but not behind the fryer. This switch must be clearly marked and readily accessible in case of
fire.
1. Check the electricity supply is correct to as shown on the Rating Plate attached to the inside of the
access door.
2. Supply terminal connections are located at the lower front of the fryer.
3. Open the door and remove the service panel (6 screws) located behind the drain valve(s) to allow
connection access for electrical supply.
4. Bring the supply cable up through the grommet at the rear of the fryer and through the compression
type gland provided on rear of main electrical switchgear panel.
5. Connect mains supply to L1, L2 and L3 switch connections for 3 phases.
6. Connect neutral and earth conductors to the neutral and earth studs respectively.
7. For all connections ensure that the conductors are secure and appropriately terminated.
8. Tighten the cable gland to secure against tension on the cable.
NOTE:
This appliance must be grounded / earthed.
Fixed wiring installations must incorporate an all-pole disconnection switch.
1. Before leaving the new installation;
a. Check the following functions in accordance with the operating instructions specified in the
'Operation' section of this manual.
Check current draw and loading for the equipment. Refer to the Specifications section for
correct electrical requirements.
Check all connections are correct and that all cover panels have been re-fitted.
Check that the unit functions in accordance with the operating instructions.
Ensure the tank drain extension and this instruction manual are left with the appliance.
Ensure that all relevant details and contacts have been added to the front of this manual.
b. Check the thermostat operation by filling the fryer with oil / shortening to the appropriate oil 'FILL
LEVEL' mark and setting the thermostat to 180°C. Turn On the fryer as shown in 'Operation
Instructions' in this manual.
c. Check the calibration of the thermostat once oil is up to temperature. If a discrepancy is found,
thermostat calibration should be referred to the supplier.
d. Ensure the operator has been instructed in the correct operation and shutdown procedure for this
appliance.
Initial Start-Up
Before using the fryer;
a. For first time use of the fryer and before using fryer for cooking product, fill the fryer with oil and
operate fryer for about 1 hour at Full Flame setting to remove any fumes or odours which may be
present in the new appliance.
b. Refer to Operation Section of this manual for details on how to operate the fryer.
2. This manual must be kept by the owner for future reference, and a record of Date of Purchase,
Date of Installation and Serial Number of Appliance is recorded and kept with this manual.
(These details can be found on the Rating Plate fitted to the inside of the access door and in
'Specifications' section of this manual.
NOTE:
If it is not possible to get the fryer to operate correctly, turn Off electrical power and
contact a qualified service person. Appliance supplier will recommend a suitable person.
Make sure that the electrical supply is turned Off before any service or maintenance work
is carried out.
10
Temperature Control Knob
Temperature Graduations
60°C to 200°C.
Power ONIndicator. (When
main power switch is ON’).
Heating ONIndicator. (When
thermostat is turned to a
selected temperature).
Operating the Reset Switches
resets power to the elements.
(One switch for each element.
Press to operate).
Turns power to the Fryer ON
and OFF’. (Green Indicator
illuminates when switched
ON’).
Neon Indicator
(Green)
Neon Indicator
(Orange)
Temperature
Cut-out Reset
Switches
Located Behind Main Access Door
Mains Isolation
Switch
Fig 2
Electronic Controller
See description of Electronic
Controller overleaf.
Operating the reset switches
resets the elements.
(One switch for each element.
Press to operate).
Turns power ONand OFFto
the unit. (Green LED Indicator
illuminates when switched
ON’).
Mains Isolation
Switch
Fig 3
Temperature
Cut-out Reset
Switches
Located Behind Main Access Door
11
Each control panel comprises the following:-
One 4 digit, seven segment display with a 0.5” high, bright green LED display.
Three green LED indicator lights located under each of the 3 Timer Controls.
NOTE: Only one temperature
setting applies to all 3 timers.
The 3 Timer Keys on each control
panel can be used to program 3
different cook times for each tank.
6 Touch Control Keys;-
ON’ / ’OFFKey.
Programme Key (P).
Left Timer - UPKey and LED Indicator Light.
Centre Timer - and LED Indicator Light.
Right Timer - DOWNKey and LED Indicator Light.
Temperature Key (Thermostat).
12
The following Parameters can be changed in Controller Basic Programming Mode:-
Timer 1 - Cook Time Settings.
Timer 2 - Cook Time Settings.
Timer 3 - Cook Time Settings.
Cooking Temperature Setting.
Keypad Lock - Unlock(Programming the Password Protection).
NOTE:
Each Timer Key on the control panel can be individually programmed with a different cook
time.
The user cannot enter Basic Programming Mode whilst a timer is running. An alarm will
sound indicating the key press, but access to programming mode will be blocked.
1. To enter Programming Mode’, press ON / OFFkey to turn ON
the control panel.
2. Press Programme Key Pto access the parameter setting required.
a. If LoCis displayed, control panel is locked which will prevent
any accidental change to the operating mode.
b. To access parameters, whilst LoCis displayed on screen,
enter the passcode 1 1 3 3.
1. To change the settings, press either or Key until the value
required is shown on the display.
2. Press Programme Key Pto confirm new value and the change will
be accepted. Display will step on to the next parameter.
To exit Programming Mode, press and hold Programme Key Pfor approximately 3 seconds, or do not
press any key for 2 minutes. The display will revert to Idle Mode’.
TIMER 1
COOK TEMPERATURE
SETTING
KEYPAD
LOCK-UNLOCK
Min 0.01
Max 99.59
Min 88°C
Max 193°C
If set to LoC’, password is required
to change any of these settings.
Password is 1,1,3,3.
TIMER 3
TIMER 2
Min 0.01
Max 99.59
Min 0.01
Max 99.59
13
NOTE: WALDORF 'Deep Fryerscan be used with both oil and shortening.
1. Before filling the tank, always check that the drain valve behind the door is closed. A locking slide is
provided on these valves and this should always be in the locked position during use.
2. Ensure that the elements are swung down into the tank(s).
OIL - Carefully fill the fryer tank until the lower Fill Level mark is reached.
Set the thermostat to the required operating temperature, the oil will expand as heated and will
reach the upper level mark when the oil is hot (180 - 19C).
The FN8127 single tank fryer will hold 27 to 29 litres of oil.
The FN8224 twin tank fryer will hold 14 litres of oil per pan.
SHORTENING - Ideally shortening should be pre-melted prior to putting it into the tank. This is normally
done in a suitable vessel on a boiling table burner(s). The liquefied shortening can then be poured
into the tank until it reaches the 'FILL LEVEL' mark.
The FN8127 single tank fryer will hold 22 - 23kg of shortening.
The FN8224 twin tank fryer will hold 11kg of shortening per tank.
Pre-Heating
NOTE: When pre-melting shortening, only heat the shortening until it is just liquefied. Do not bring
the shortening up to high temperature as handling of hot shortening is dangerous.
If it is not possible to pre-melting the shortening, carefully cut shortening into small pieces and
pack below, all around and above the elements, ensuring that the element can fully lower to
operate the element tilt microswitch, otherwise the fryer will not operate.
FN8127E and FN8224E Only;- Set the tank control therm ostat to 120°C and sw itch
ON the appliance for 30 seconds and then OFF for 1 minute. Repeat the cycle until all the
shortening is melted enough to apply full power to the heating elements. To speed up this
process, break up the shortening and stir carefully during the melting process.
Add more shortening until the tank is filled to the level marked on the tank side. Refer to Fig 4
above.
NOTE: Running the elements continuously will cause the shortening in contact with the element to
overheat, resulting in premature oil breakdown. Never allow the shortening to smoke whilst
melting as this indicates that the temperature is too high. If the shortening starts smoking,
increase the Offintervals of the elements.
Fig 4
CORRECT LEVEL FOR FRYING MEDIUM WHEN
AT FRYING TEMPERATURE.
CORRECT LEVEL FOR FRYING MEDIUM WHEN
COLD.
14
1. Turn ONmains power at the mains supply.
2. Turn ONmains isolator switch located behind the front access door. Green neon indicator will
illuminate to indicate that there is mains power to the fryer.
3. Set the tank control thermostat to the temperature required. Orange neon indicator will illuminate
to indicate that the heating elements are On’.
4. When oil in tank reaches the set temperature, Orange neon will extinguish to indicate that fryer is up
to the selected temperature.
5. To turn OFFthe fryer, open the front access door and turn the mains Isolator Switch to the OFF
position.
6. Turn OFFmains power at mains supply.
THE OPERATOR MUST TAKE GREAT CARE TO USE THE EQUIPMENT SAFELY AND TO GUARD IT AGAINST THE RISK
OF FIRE.
DO NOT LEAVE THE FRYER UN-ATTENDED DURING OPERATION.
DO NOT REPLENISH THE OIL (FRYING MEDIUM) IN THE FRYER WHEN THE FRYER IS HOT.
DO NOT OVER FILL THE OIL (FRYING MEDIUM) IN THE FRYER ABOVE THE TOP LEVEL MARK.
DO NOT ALLOW THE OIL (FRYING MEDIUM) IN THE FRYER TO FALL BELOW THE LOWER LEVEL MARK.
DO NOT ALLOW THE OIL (FRYING MEDIUM) IN THE FRYER TO OVERHEAT.
DO NOT INTRODUCE WET FOOD OR WATER INTO THE HOT OIL (FRYING MEDIUM).
DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO THE FRYER
WHILST THE FRYER IS STILL HOT.
15
TURN ON FRYER
Press ON / OFF key to turn ONControl Panel.
When oil is Up To Temperature, display will show the following.
If t - 1’ selected in Advanced
Program Settings, display will show
Actual Temperature of oil.
Neon Dot Indicates Heating isON
If Melt cycle is active, display will show the
following. Refer to Controller Advanced
Programming Mode for available settings.
If t - 0’ selected in Advanced
Program Settings, display will show
the following.
Refer to Controller Basic Programming Modeat the start of this section for the basic programmable
settings for the controller.
Refer to the Controller Advanced Programming Modesection for controller advanced programming.
Fryer can now be used without using the Timers, if required.
TURN ON FRYER
Press ON / OFF key to turn ONControl Panel.
When oil is up to temperature, display will show the following.
If t - 1’ selected in Advanced
Program Settings,
Actual Temperature of oil is displayed.
If t - 0’ selected in Advanced
Program Settings, display will show
the following.
Display will show the following. Refer to Controller
Advanced Programming Mode for settings.
Fryer can now be used without using the Timers, if required.
16
Press Timer 1, 2 or 3 as required.
LED beneath timer will flash continuously.
On completion of frying, beeper will sound
and display will show which timer has
completed frying.
Left Centre or Right
Press Timer Key to cancel Beeper and Timer
Press Temperature Key.
Display shows Actual Temperature.
1. Press the On /OffKey on the control panel.
2. Turn Offthe power supply at the mains supply.
These fryers have been fitted with a Fail Safe Over Temperature Safety Cut-Outwhich will protect the oil /
fat from excessive temperature if the thermostat control should fail. The power light will turn Off if the
over temperature control has been triggered. The twin tank fryer (FN8224E) has an individual Fail Safe
Over Temperature Safety Cut-Outfor each tank.
Over-Temp Control
The over-temp thermostat is mounted behind the transformer panel, behind the access door and its
sensing bulb is located alongside the thermostat (E and EE Models).
This control is set for approx. 225-235°C oil cutout temperature. To reset the 'Overtemp Control',
allow the oil to cool down to approx 160-180°C then operate the red switch behind the access door.
The power light will then turn On.
NOTE: On dual tank models, if either 'Over-Temperature Control' is triggered, a fault exists in the
main thermostat and this must be reported and repaired. For temporary operation, Model
FN8127EE is fitted with a backup thermostat.
Press Temperature Key again,
within 3 seconds.
Display shows Set Temperature.
Display will count down time to
completion of frying.
NOTE: Refer to Basic Programming Mode for
information on how to set the Timer
Pre-Set times.
NOTE: Refer to Basic Programming Mode for
information on how to set the Cooking
Temperature.
17
To achieve the best results, cleaning must be regular and thorough and all controls and mechanical parts
checked and adjusted periodically by a competent serviceman. If any small faults occur, have them
attended to promptly. Don't wait until they cause a complete breakdown. It is recommended that a service
check is conducted every six months.
Clean the fryer regularly. A clean fryer looks better, will last longer and will perform better.
NOTE:
DO NOT use sharp scrapers, strong solvents, abrasive or caustic detergents as they could
corrode or damage the fryer.
Ensure that any detergent or cleaning material has been completely removed after each
cleaning.
To keep your fryer clean and operating at peak efficiency, follow the procedures shown below:-
1. At the end of each day or at the end of each shift, if frying schedule is heavy, frying medium should
be drained and filtered into a receptacle.
2. Always filter the fryer when the cool zone under elements is hot
and liquid. A cold fryer heated up won't drain, because frying
medium in this zone will remain hard if using solid fat / oils.
3. Screw the drain extension pipe onto the end of the drain valve
(see Fig 5) and position a suitable container and filter under the
drain extension pipe.
DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO FRYER WHILST
FRYER IS STILL HOT.
Never drain the fryer with power or elements turned ON
Always switch OFF' fryer before draining or re-filling tank.
DO NOT ATTEMPT TO MOVE FRYER WHILST FRYER IS FULL OF OIL.
Fig 5
Drain
Extension
Pipe
18
Opening the Drain Valve
a. Lift the locking slide on valve handle
(Fig 6) to release the valve.
b. While holding the locking slide in the
withdrawn position, rotate handle
anticlockwise (Fig 7) to open the
valve.
c. When the valve is closed, the locking
slide will drop down over the locking
valve to prevent accidental opening of
the valve, as shown in Fig.6.
4. Do not empty total fryer contents into one large container, as this will be dangerous and may be
difficult, when lifted up, to pour hot oil back into the fryer tank.
5. Slip a muslin or other suitable filter bag over the end of the drain valve. Crumbs will be caught in
the bag but the frying medium will strain freely through into the container.
6. Open the drain valve slowly to minimise splashing, and take care not to overfill the container.
7. When tank has been drained, use a ladle or small pan with a handle and dip into the hot frying
medium from the container and pour around the sides and bottom of the fryer tank to wash out
crumbs and particles adhering to the tank.
8. Continue to dip and pour until all crumbs and particles are washed down and into the filter bag.
9. Open the drain valve fully and check for any particles or crumb residue lodged in the valve. Clean
out the valve with a stiff nylon brush. Do not use a wire brush as this may damage the valve
seating and will eventually lead to valve leakage. If the obstruction cannot be removed with a
brush, use a wooden probe to dislodge the obstruction.
10. Wipe all exterior panels with a cloth dampened with detergent and rinse off any residue with clean
warm water.
11. Clean the Control Panel with a damp cloth lightly moistened with a solution of water and a
commercial quality foodservice approved detergent.
12. Once the daily cleaning is completed, close the drain valve and pour the frying medium back into the
fryer tank.
HOT OIL WILL BURN - DO NOT RUSH THIS JOB.
Fig 7
Fig 6
Locking Slide
Locking
Slide
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Moffat FN8127E Operating instructions

Category
Deep fryers
Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI